Decrease In Average Particle Size Research Articles

Synthesis and characterization of polyaniline-based composites using cellulose nanocrystals as biological templates

Polyaniline (PANI) is considered as an ideal electrode material due to its remarkable Faradaic activity, exceptional conductivity, and ease of processing. However, the agglomeration and poor cycling stability of PANI largely limit its practical utilization in energy storage devices. To address these challenges, PANI was synthesized via a facile one-pot, two-step process using cellulose nanocrystals (CNCs) as bio-templates in this work. Zeta potential and particle size measurements revealed that the CNC template could impart improved dispersion stability to the synthesized PANI, which exhibited a decrease in average particle size from 1100 nm to 300 nm as a function of 10 % CNCs. Furthermore, the effect of CNC loadings on the performance of PANI was systematically investigated. The results showed that the specific capacitance of PANI/CNC increased from 102.52 F·g−1 to 138.12 F·g−1 with the CNC loading increase from 0 to 10 wt%. Particularly, the PANI/CNC composite film with a 1:9 ratio (C-P-10 %) demonstrated a capacity retention of 84.45 % after 6000 cycles and an outstanding conductivity of 526 S·m−1. This work generally offers an effective solution for the preparation of high-performance PANI-based composites, which might hold great promise in energy storage device applications.

Gold doped Wollastonite hybrid nanocomposites as a candidate for bone regeneration/healing applications: Biocompatibility and antimicrobial efficacy

This work investigates the bioactivity of pure Wollastonite and gold-doped Wollastonite nanohybrids synthesized via a wet chemical technique. Doping with gold nanoparticles at different ratios for Wollastonite, where a dramatic decrease in the respective average particle sizes at the lowest doping ratio of 1.25 wt./v%, then the particle size raised gradually with an increase in the content of gold nanoparticles. In addition, a significant increase in the calculated surface area and the cumulative pore volume upon incorporating gold nanoparticles with the lowest doping ratio of 1.25 wt./v% is associated with a slight decrease in the average pore size. Then, a gradual decrease in the calculated surface area and cumulative pore volume with the increase of doping ratio with gold nanoparticles is associated with an increase in average pore size. The results revealed that after two days of incubation for treated MG-63 cells, the W/Au 5 wt./v% showed the significantly highest alkaline phosphatase (ALP) activity among all other concentrations and the control cells. The ALP activity exceeded four mU/mL. After four days of incubation, the ALP activity in all doping ratios was significantly higher than the control cells, with no significant difference among other groups, but lower than ALP levels after two days of incubation. Also, pure Wollastonite and gold-doped Wollastonite nanohybrids, especially the lowest doping ratio of 1.25 wt./v%, have remarkable efficacy in combating E. coli (Gram-negative), S. aureus (Gram-positive) and Candida albicans. In vitro studies showed that pure Wollastonite and gold-doped Wollastonite nanohybrids had minimal cytotoxic effects on osteosarcoma MG-63 cells, while they showed remarkable cell proliferation even at low concentrations. Based on the in-vitro ALP, bioactivity and biocompatibility results, the content of ALP can directly reflect the activity or function of osteoblasts and is positively correlated with the mineralization ability of cells, which shows that pure and gold-doped Wollastonite nanohybrids were suitable candidates for bone regeneration/healing applications.

Encapsulation of Black Rice Bran Extract in a Stable Nanoemulsion: Effects of Thermal Treatment, Storage Conditions, and In Vitro Digestion.

This study aimed to improve the dispersibility of phenolic compounds from black rice bran through the encapsulation process within nanoemulsion. The study focused on assessing the stability of the nanoemulsions, which were prepared using a combination of surfactants with distinct hydrophilic-lipophilic balance (HLB) values and sunflower oil under different thermal treatments and storage conditions. The study revealed a significant correlation between the mixed surfactant HLB value and the nanoemulsions properties, including average particle size, polydispersity index (PDI), and ζ-potential. Specifically, an increase in the HLB value was associated with a decrease in the initial average particle size. The encapsulated polyphenols exhibited remarkable stability over a storage period of up to 30 days at different temperatures with no significant changes observed in particle size or PDI. The study also investigated the impact of different ionic strengths (0.2, 0.5, and 1.00 mol L-1 NaCl) on the physical stability and antioxidant black rice bran extract nanoemulsion, and the results revealed that adding NaCl influenced the particle size and surface charge of the nanoemulsions. Total phenolic content and DPPH results demonstrated a significant impact of salt concentration on antioxidant properties, with varying trends observed among the HLB formulations. Furthermore, the behavior of the encapsulated extracts during digestion was examined, and their antioxidant activity was evaluated.

Modeling Linear Polarization of the Didymos–Dimorphos System before and after the DART Impact

We analyze the polarization observations of the Didymos–Dimorphos system before and after the impact by the NASA Double Asteroid Redirection Test spacecraft on Dimorphos. We fit empirical polarization phase curve models and statistically confirm the discovery by Gray et al. about the degree of linear polarization of the system decreasing on the impact and remaining altered for at least 30 days post-impact. With numerical simulations of particles in the geometric optics domain, we estimate the dominant size of the particles either in the regolith of Didymos and Dimorphos or in the impact-driven ejecta cloud to be several hundred micrometers. The observed change between the pre-impact and post-impact systems indicates either a decrease in average particle size of some tens of micrometers or a decreased level of space weathering.

Comprehensive investigation of the impact of milling time on microstructural evolution and tribological properties in Mg-Ti-SiC hybrid composites

This research delves into the effects of milling time on the properties of Mg-Ti dual matrix composites reinforced with nano SiC powders, processed via spark plasma sintering. The study, driven by the need for advanced materials with enhanced wear resistance for the aerospace and automotive sectors, focuses on microstructural evolution and wear characteristics. It aims to understand how varying milling durations influence particle morphology, crystallite structure, and consequently, tribological behavior. Initial observations indicate a decrease in average particle size to 5.72 µm, followed by an increase to 14.83 µm due to cold welding and particle trapping, demonstrating the dynamic nature of particle morphology under different milling conditions. X-ray diffraction analysis reveals a notable reduction in magnesium's crystallite size with increased milling, suggesting plastic deformation. This study underscores that smaller crystallite sizes do not always correlate with strain, especially in smaller dimensions. Additionally, the research records variations in density and hardness, influenced by milling time and particle dispersion, with hardness showing a complex variation, peaking at 108 HV. Overall, the findings highlight the critical role of milling duration in shaping the microstructure and determining the mechanical and wear properties of Mg-Ti-SiC composites. This investigation contributes to the optimization of wear resistance in these composites, enhancing their applicability in high-performance industrial applications.

Novel mesoporous iron oxide synthesized from naturally occurring magnetic sand: A potential and promising catalyst for chemical processes

This paper presents the synthesis of iron oxide from natural magnetic sand that was obtained from Michika, Adamawa State, Nigeria. Characterization of the raw magnetic sand and the synthesized iron oxide was performed to investigate the effect of the synthesis method on functional groups, morphology, composition, crystallinity, acidity and surface area/pore distribution using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy – energy dispersive X-ray (SEM – EDX), X-ray fluorescence (XRF), X-ray diffraction (XRD), BET and pyridine FTIR, respectively. The XRF analysis of the two samples revealed a significant variation in oxide composition. The raw magnetic sand had an iron oxide content of 64.69 wt%, which increased to 85.20 wt% after synthesis. Furthermore, the SEM-EDX analysis indicated a decrease in average particle size from 114.6 and 36.8 µm for the respective samples. The XRD patterns revealed that the crystallinity increased after synthesis. FTIR showed the associations of functional groups present in the sample. The wavebands in the range 550 – 630 cm−1, which correspond to the Fe – O bond, improved clearly in the synthesized iron oxide sample, particularly at 582 cm−1. The pyridine FTIR depicts that the overall acidic site is higher in the synthesized sample. The N2 adsorption–desorption procedure shows an increased BET surface area from 9.394 m2/g (raw) to 24.851 m2/g (synthesized). Overall, the results showed that the synthesized mesoporous iron oxide exhibits properties similar to materials that have a high potential for application as catalysts in chemical processes.

Impact of Micropulse and Radio Frequency Coupling in an Atmospheric Pressure Plasma Jet on the Synthesis of Gold Nanoparticles

Gold nanoparticles have been extensively studied due to their unique optical and electronic properties which make them attractive for a wide range of applications in biomedicine, electronics, and catalysis. Over the past decade, atmospheric pressure plasma jets in contact with a liquid have emerged as a sustainable and environmentally friendly approach for synthesizing stable and precisely controlled dispersions. Within the context of plasma jet/liquid configurations, researchers have explored various power sources, ranging from kHz frequencies to nanopulse regimes. In this study, we investigated the effects of coupling two distinct power supplies: a high-voltage micropulse and a radio frequency (RF) generator. The variations within the plasma induced by this coupling were explored by optical and electrical measurements. Our findings indicated a transition from a bullet plasma propagation mechanism to a capacitive coupling mechanism upon the introduction of RF energy. The impact on the production of metal nanoparticles was also examined as a function of the radio frequency power and of two distinct process gases, namely helium and argon. The characterization of gold nanoparticles included UV-visible spectroscopy, dynamic light scattering, and scanning electron microscopy. The results showed that the size distribution depended on the type of process gas used and on the power supplies coupling. In particular, the incorporation of RF power alongside the micropulse led to a decrease in both average particle size and distribution width. The comparison of the different set up suggested that the current density can influence the particle size distribution, highlighting the potential advantages of the use of a dual-frequency atmospheric pressure plasma jet configuration.

Controlling the combustion and agglomeration characteristics of solid propellants via new micro-unit composite fuel Al@AP

New micro-unit composite fuels Al@AP with different mass ratios of Al and AP are designed, prepared, and added to solid propellants in place of the original aluminum powder. Through Thermogravimetric Analysis- Differential scanning calorimetry- Mass Spectrometry (TG-DSC-MS), laser ignition experiment, thermocouple temperature measurement, burning rate test, and combustion diagnostic, we study how Al@AP affects the ignition, combustion, and agglomeration properties of solid propellants. The results indicate that the increase of Al content of Al@AP can promote the advance of thermal decomposition of AP. As the AP content increases in Al@AP, the ignition delay time of Al@AP decreases by three times, and the mass burning rate increases by almost five times. At the same time, Al@AP significantly improves the burning rate and temperature gradient. When compare to the baseline propellant, Al@AP-containing propellants present a maximum increase in burning rate of 33% at low pressures and 19% at high pressures. In terms of agglomeration reduction, the number of large-size agglomerates in the CCPs of propellants containing Al@AP is reduced, the average particle size decreases by 78%, and the combustion efficiency increases to 99.34%. A mechanism is proposed to explain how the micro-unit composite fuel Al@AP alters propellant combustion and agglomeration. In summary, Al@AP provides excellent control over ignition, combustion, and agglomeration characteristics. This study provides guidance on the application and development of new aluminum-based composite fuels used in solid propellants.

Characterization of silver oxide thin films with thickness variation prepared by thermal evaporation method

Thermal evaporation technique has been used to produce silver oxide (AgO). The findings demonstrate that the crystal quality of the AgO film was dominated by the thin and sharp peaks at (111) plans. Atomic Force Microscopy (AFM) confirm that the distribution grains size appears nanostructure and homogeneous in all films. RMS decreased from 6.84 nm to 2.17 nm with thicknesses 200 nm. The surface roughness decreased from 7.82 nm to 3.22 nm. The distribution of grains size appears nanostructured and homogeneous in all films, and a slight decrease in average particle size. The surface displayed that the roughness decreased with the increase in thicknesses. The spectrum fluctuation of their optical constants has been calculated using transmittance and absorption data. In the visible region of the wavelength, all films have a high absorption coefficient with a value of 104 (cm-1 ). According to the optical measurements, the films have a band gap between 1.73 and 1.61 eV. The Extinction coefficient and refractive index drop as film thickness rises.

Effective role of vibrational annealing in enhancing room temperature physical properties of Co doped ZnO nanoparticles by using novel TVA technique

Well-annealed nanocrystalline semiconductor materials in pellet or thin film form, composed of small grains with a high surface-to-volume ratio, are considered as promising candidates for multiple device applications. However, no such method is available yet that can control the grain size of such samples during heat treatment. In this present work, a novel thermo-vibrational annealing (TVA) setup for processing nanocrystalline materials was designed and fabricated in-house. Here both thermal and mechanical vibrational energy were simultaneously applied to the sample during annealing, followed by vibrational dry quenching in the presence of an inert gas environment. Co-doped ZnO pellets were synthesized by chemical route pyrophoric method followed by annealing at 800 °C for 4 h using this set up. For comparison, one pellet was annealed with vibration with calibrated vibration at a speed of 360 rpm, and another pellet was annealed without vibration. X-ray diffraction (XRD), Raman and Fourier transform Infrared (FTIR) spectroscopic studies showed the formation of a single crystalline phase with hexagonal wurtzite structure of both the samples and the proper incorporation of Co2+ ions into the ZnO matrix without any impurity phases, which was also confirmed by energy dispersive X-ray (EDX) spectroscopy studies. Scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) studies confirmed the decrease in average grain and particle size of the sample when processed with the TVA setup. Ultraviolet–Visible spectra showed that the bandgap energy of the Co-doped ZnO sample varies inversely with particle size. Hall-effect measurements demonstrated the semiconducting nature of both samples with n-type charge carriers. The presence of Co2+ ions in the wurtzite ZnO lattice was confirmed by X-ray photoelectron spectroscopy (XPS). The magnetic properties were studied using a SQUID magnetometer, which confirmed that a Co doped ZnO sample annealed with the TVA technique exhibit better room temperature ferromagnetism properties compared to sample annealed without vibration. Based on these studies, it was believed that the sample annealed by mechanical vibrational energy with vibrational dry quenching has a great influence on several physical properties of any material and hence Co doped ZnO sample processed with this TVA technique can be used as a promising candidate for multiple sensor and magnetic storage devices.

Study of the influence of methanol/F-T diesel combustion particle materiality parameters on the deposition process in diesel particulate filter trap units

The use of different fuels will change the structural characteristics of the diesel engine exhaust particulates. This paper studies the impact of the particle physical and structural properties on DPF capture, and proposes to measure the particle deposition by particle chain length and particle layer thickness. This study builds a test bench based on a four-cylinder diesel engine, using F-T diesel fuel with 0%, 5%, and 15% methanol mixing ratio to collect particles after running for half an hour under the calibration condition. The physical properties of particles were analyzed by synchrotron radiation small angle scattering. The particle formation rate, friction between particles, particle size, and other parameters of mixed fuel combustion particles were then confirmed. The particle model was developed in EDEM based on the experimental data, and the creation of particle chains was studied. In addition, the impact of collision bounce on the particle deposition was taken into consideration to mimic the process of particle collision deposition on the filter wall. The results show that when the methanol mixing ratio increases, the Particles Number (PN) value of methanol F-T diesel combustion particles increases, the inter-particle friction increases, and the average particle size decreases. During the deposition process, the amount of deposition on the non-windward side of the DPF trap unit sharply increases, and the particle deposition efficiency increases with the increase of the deposition time. The particle deposition increases with the deposition time, and the thickness and length of the particle layer and chain increase with the increase of the particle number, friction, and size.

White-flesh guava juice clarification by a fixed-angle conical rotor centrifuge laboratory and characterization of continuous disk stack centrifuges

The two objectives of this paper were to determine the effect of centrifugation parameters on guava juice physicochemical characteristics and to identify operational characteristics of continuous disc-stack centrifuges based on the performance of a laboratory centrifuge. Effects of g-force (149 g–3731 g) and centrifugation time (10–40 min) on juice physicochemical characteristics (protein, pectin, galacturonic acid, dry matter, total soluble sugars contents; pH; electrical conductivity, clarity and particle size distribution) were assessed. Laboratory centrifuge performance was evaluated for 1343 g, 2388 g and 3731 g. At 1343 g, separation limits (xmax), feed flow-rates of disc-stack centrifuges and cut-off sizes (x50) were determined for corresponding laboratory centrifuge operation times. Significant decrease in average particle size, protein and pectin contents was observed, contrary to juice clarity. Similar clarification efficiency was obtained for g-forces ≥ 1343 g. xmax were 2669 nm, 2200 nm and 1783 nm, with corresponding x50 for continuous centrifuges, 1887 nm, 1556 nm, 1261 nm, for 20 min, 30 min and 40 min, respectively.

Evaluating the role of salts on emulsion properties during water-based enhanced oil recovery: Ion type, concentration, and water content

Potential determining ions (SO42−, Mg2+, Na, and Ca2+) positively affect oil recovery. These ions can cause changes in the oil and water system due to their ionic radius and proper charge density. Besides the type of ions, the concentration of these ions is also important. In order to maximize oil recovery, the concentration of these active ions should be at a level that pulls the polar components of the oil towards the oil–water interface and causes the interfacial tension to decrease, resulting in a decrease in capillary force and an increase in oil recovery. In some cases, the presence of various ions in the formation water or injection water provides the conditions for the formation and stability of the emulsion. Emulsion formation sometimes reduces production and sometimes improves production from oil reservoirs. Therefore, it is imperative to study the effects of ions on the formation, stability, and viscosity of emulsions. Regarding the emulsion stability in the presence of different ions, there are high uncertainties, and there is no uniform opinion on this matter. In this study, MgCl2, CaCl2, NaCl, and Na2SO4 were used to investigate emulsion properties. Droplet size and viscosity were measured using an optical microscope and a rolling ball viscometer, respectively, in order to determine emulsion stability. The results have shown that salts with higher positive charge density, such as MgCl2 and CaCl2 can significantly reduce the size of emulsion droplets and increase emulsion stability. Moreover, the presence of divalent anions such as sulfate reduces the amount of asphaltene at the interface between oil and water, thereby reducing the stability of the emulsion. In the order of MgCl2 > CaCl2 > Na2SO4 > NaCl, salts decreased the droplet size and increased the emulsion stability. The viscosity of the emulsion also showed a similar trend, as the average particle size decreases, the viscosity of the emulsion increases. Based on the results, the size of the emulsion droplets decreases up to a certain concentration and then increases. In the case of all salts, this concentration was equal to 10,000 ppm. The viscosity of the emulsion shows an increasing trend up to the concentration of 10,000 ppm, and after this concentration, it shows a decreasing trend. Salt-in and salt-out effects are responsible for the reduction and increase in droplet size. This study can provide insight into the effect of different ions on the stability and viscosity of the emulsion, as well as the design of the injection fluid for the enhanced oil recovery process.

Utilization of Sulfonated Waste Polystyrene-Based Cobalt Ferrite Magnetic Nanocomposites for Efficient Degradation of Calcon Dye.

We presented a simple and efficient method for making a polymer–metal nanocomposite using various amounts of cobalt ferrite magnetic nanoparticles (CoFe2O4 MNp) with sulfonated waste polystyrene (SWPS) and utilized for Calcon dye degradation. The MNp was encapsulated with SWPS to avoid agglomeration and maintain its smaller size. ATR-FTIR, Raman spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), dynamic light scattering (DLS), field emission scanning electron microscopy (FESEM), high-resolution transmittance electron microscopy (HR-TEM), atomic force microscopy (AFM) and solid UV were used to analyze the produced polymeric magnetic nanoparticles (SWPS/MNp). As the MNp loading increases, the average particle size decreases. For Calcon dye degradation, SWPS/MNp (20 wt%) was utilized with a smaller average particle size, and the structural changes were detected using a UV-Vis spectrophotometer. As a result, the Calcon dye’s characteristic absorbance peak at 515 nm was red-shifted to 536 and 565 nm after 5 min, resulting in a color shift from dark brown to light blue that could be seen with the naked eye. A strong linear correlation was found between the red-shifted absorbance and the concentration of dye solution over the range of 10–100 ppm under optimal conditions. The proposed dye degradation process is simple, efficient, and environmentally friendly and has been successfully used to purify organic azo-dye-containing water.

Impact of Atomization Pressure on the Particle Size of Nickel-Based Superalloy Powders by Numerical Simulation.

Vacuum induction melting gas atomization (VIGA) has evolved as an important production technique of superalloy powders used in additive manufacturing. However, the development of powder preparation techniques is limited because the crushing process of gas-atomized metal melt is difficult to characterize by conventional experimental methods. Herein, we report the application of computational fluid dynamics to simulate the breaking behavior of droplets in the process of preparing nickel-based superalloy powders by VIGA, as well as the results on the effect of gas pressure on the atomization process and powder particle size distribution of metal melt. In the process of primary atomization, the crushing morphology of superalloy melt shows an alternate transformation of umbrella shapes and inverted mushroom cloud shapes, and with the increase in atomization pressure, the disorder of the two-phase flow field increases, which is conducive to sufficient breakage of the melt. Most importantly, in the process of secondary atomization and with the increasing atomization pressure, the particle size distribution becomes narrower, the median particle diameter and average particle size decrease, and the decreasing trend of the particle size increases gradually. The simulation results are compliant with the performed nickel-based superalloy powder preparation tests. This study provides insight into the production and process optimization of superalloy powder prepared by the VIGA method.

Chemo-mechanical preparation and investigation of physio-chemical and thermo-sensitive properties of Octogen

ABSTRACT Present work demonstrates the effect of in tandem application of chemo-mechanical methods on physio-chemical and thermo-sensitive properties of HMX. Solvent-antisolvent recrystallization produced γ-polymorph of HMX with mean diameter ~7 μm and ~8 μm when acetone and DMF were used as solvent respectively, whereas with γ-butyrolactone, β-HMX with larger particle size (mean diameter ~24 μm) was produced. Ultrasonication initially (1 h) resulted in increase in particle size but with increase in duration (24 h) particles size decreased to (~4 μm) whereas, ball milling resulted in decrease in average particle size to ~1 μm with β-polymorphic form with reduced impact sensitivity.

Effect of Gd doping on magnetic and MCE properties of M-type barium hexaferrite

Gd doped barium hexaferrite (BaFe12−xGdxO19, x = 0.0–0.7) has been synthesized by the sol-gel method to explore its magnetic and MCE (magnetocaloric effect) properties. The materials crystallize to hexagonal magnetoplumbite phase. Average particle size decreases with the increase in Gd concentration in barium hexaferrite (BHF). The coercive field increases from 3.2 to 4.8 kOe, and saturation magnetization decreases from 68.21 to 54.23 emu/g with the increase in Gd concentration from x = 0.0 to x = 0.7. These large changes in magnetic parameters reveal the effect of Gd concentration in BHF. The saturation magnetization monotonously reduces with an increase in Gd concentration in BHF due to a decrease in average particle sizes. The saturation magnetization is found to be higher at a lower temperature (60 K) compared to that of room temperature (300 K). It is due to a reduction in thermal energy at low temperature which is smaller compared to the magnetic Gibbs free energy at low temperature. Hence, the magnetic spins are freezing along the applied magnetic field direction at the low temperature. Also, the magnetocrystalline anisotropy constant (obtained by the "Law of Approach to Saturation method") is found to be more at low temperature compared to that of room temperature due to an increase in the strength of spin-orbit coupling with the decrease in temperature (i.e. thermal energy). The M-T curves and M-H hysteresis loops reveal paramagnetic to ferromagnetic transition at the Curie temperature. The maximum entropy change was found to be in the range of 0.12–0.72 J/kgK in a window of the applied magnetic field of 0.5–3 T, and the corresponding RCPmax was found to be 2.5–27.5 J/kg. The present study opens a window to explore the MCE on BHF based material.

Synthesis and Characterization of Polyethylenimine-Silica Nanocomposite Microparticles.

A novel procedure for the synthesis of polyethylenimine (PEI)-silica nanocomposite particles with high adsorption capacities has been developed based on an emulsion templating concept. The exceptional chelating properties of PEI as the parent polymer for the particle core promote the binding abilities of the resulting composite for charged species. Further, the subsequent introduction of silica via the self-catalyzed hydrolysis of tetraethoxysilane facilitates production of robust composite particles with smooth surfaces, enabling potential use in multiphase environments. To enable tailored application in solid/liquid porous environments, the production of particles with reduced sizes was attempted by modulating the shear rates and surfactant concentrations during emulsification. The use of high-speed homogenization resulted in a substantial decrease in average particle size, while increasing surfactant loading only had a limited effect. All types of nanocomposites produced demonstrated excellent binding capacities for copper ions as a test solute. The maximum binding capacities of the PEI-silica nanocomposites of 210-250 mg/g are comparable to or exceed those of other copper binding materials, opening up great application potential in resources, chemical processing, and remediation industries.

MoO2/mesoporous carbon and MoO2/reduced graphene oxide composite electrodes for supercapacitor applications

The electrochemical properties of MoO2/mesoporous carbon and MoO2/reduced graphene oxide (rGO) materials have been investigated. Composite materials have been obtained by ultrasound dispersion of hydrothermally synthesized MoO2 and carbon or rGO (mass ratio of 1:1 and 1:2). The samples have been tested using XRD, SEM, and low-temperature nitrogen adsorption–desorption. The electrochemical performance was investigated by cyclic voltammetry and galvanostatic cycling methods. The maximal specific capacitance values for MoO2/carbon (1:1) and MoO2/carbon (1:2) materials are 225 and 120 F/g, respectively. It is the evidence that increase in carbon content causes specific capacitance decreasing. For the case of MoO2/reduced graphene oxide (1:1) material the maximal value of the specific capacitance is 52 F/g that is less than one for pure MoO2. An increase in reduced graphene oxide content causes the increase in specific capacitance value up to 232 F/g that corresponds to the decrease in MoO2 average particle sizes and contribution of reduced graphene oxide component to pseudocapacitance response.

Effect of thermomechanical treatment on MX phase precipitation behavior in CLAM steel

Reduced Activation Ferritic/Martensitic (RAFM) steels are the preferred first wall structural materials in nuclear fusion experimental reactors at this stage, which puts forward high requirements for its creep properties. Previous references point out that the main factor for the creep resistance of RAFM steel is the massively precipitated MX phases in the matrix. Thermomechanical treatment (TMT) technology can promote the precipitation of a large number of nano-sized MX phases, and has great potential for improving the creep strength of RAFM steels. In this paper, China Low Activation Martensitic (CLAM) steel is taken as the research object, and four different thermomechanical treatment processes are designed for comparison. The purpose is to deepen our understanding of the effects of austenitization temperature, deformation temperature and strain on the precipitation of MX phases. It is found that the number density of MX phase after TMT increases by two orders of magnitude, and the average particle size decreases by about 79% when the austenitization temperature increases from 1000 to 1150 °C, while the effect of deformation temperature and strain is relatively small; after TMT, the specimen with the largest number and the smallest size of MX phase has the best creep performance, and vice versa.