Decoupling Structure Research Articles

A Dual‐Polarized Wide‐Angle Scanning Linear Phased Array Antenna With Simple Decoupling Structure

ABSTRACTA dual‐polarization linear phased array with a simple decoupling structure is designed for wide scanning in this letter. The suggested antenna is made up of two printed dipole antennas that are orthogonally arranged and have a high cross‐polarized isolation. Metal sheets cladding on antenna substrates serve as a decoupling structure, with an array element spacing of 0.48 . A linear phased array of seven elements is fabricated and measured to ensure that the planned array is feasible. The simulated and measured results demonstrate that the phased array can scan its main beam up to ±75° in dual‐polarized excitations at 5.6–6.4 GHz. The co‐polarized mutual coupling is below −28 dB, and the active reflection coefficient of the element is less than −15 dB.

Compact high isolation MIMO antenna array for 6G application (0.1–10 THZ)

ABSTRACT In wireless communication, channel capacity and reliability can be increased using a Multiple Input Multiple Output antenna. For several future applications, the sixth generation terahertz frequency spectrum (0.1–10 THz) will be used to increase the communication speed in wireless networks. To minimise coupling and reconfiguration, the decoupling structure and pin diodes are used in the MIMO antenna. This research presents a four-port electromagnetic band gap-based MIMO antenna array for 6 G applications. The entire MIMO system is influenced by the electromagnetic coupling between the four or eight MIMO parts. In the ground plane, antenna size reduction, insulation improvement, and defective ground are used. Here, the antenna is designed and compared using the two substrates Flame Retardant and polyimide. The performance of the suggested design is 288 GHz Polyimide and 301.6 GHz FR4. The suggested design showed better performance of the antenna as well as diversity measures.

A compact circularly polarized dielectric resonator antenna with MIMO characterizations for UWB applications.

Ultra-wideband (UWB) technology is extensively used in indoor navigation, medical applications, and Internet of Things devices due to its low power consumption and resilience against multipath fading and losses. This paper examines a multiple-input multiple-output (MIMO), circularly polarized (CP) dielectric resonator antenna for UWB systems. Compact form factor, high gain, wideband response, improved port isolation, and high data rates are the major design goals. This arrangement consists of two identical DRAs with self-decoupled orthogonal orientations eliminating the need for extra decoupling structures while achieving an impressive maximum isolation of 43 dB. The corner-edge feeding mechanism of the extended feedline generates two orthogonal E-fields, facilitating circular polarization. Additionally, a printed hook-shaped stub integrated with the ground plane enhances CP performance across the two operating bands without altering the DR structure. Fabrication and testing exhibit an impressive 133 impedance bandwidth (2.5-14 GHz) with high port isolation. For a 3 dB axial ratio reference, the single-element design exhibits axial ratio bandwidths (ARBW) of 1.2 GHz (3.6-4.8 GHz) and 0.8 GHz (9.3-10.1 GHz). Remarkably, the MIMO configuration achieves a single ARBW of 0.5 GHz (3.9-4.4 GHz). Detailed investigations of MIMO performance parameters, including diversity gain, envelope correlation coefficient, channel capacity loss, and total active reflection coefficient, underscore the design's efficacy, making it a good choice for UWB wireless applications.

Machine learning technique based highly efficient slotted 4-port MIMO antenna using decoupling structure for sub-THz and THz 6G band applications

Machine learning technique based highly efficient slotted 4-port MIMO antenna using decoupling structure for sub-THz and THz 6G band applications

A novel high‐isolation dual‐polarized air‐patch antenna based on composite decoupling structure

AbstractThis paper presents a novel wideband dual‐polarized air‐patch antenna with enhanced port isolation. The proposed design consists of a suspended metal patch, two feeding slots, and novel composite decoupling structures (CDS). The CDS is composed of two reactive loads (RLs), an additional square slot (ASS), and two neutralizing lines (NLs). The reactive loads and one NL are connected to the feeding slots. The other NL is connected to the ASS. The CDS plays a critical role in achieving wideband high port isolation. The decoupling principles are illustrated by using a circuit model and through rigorous mathematical derivation. Design evolution of the proposed antenna (Ant 1–5) was carefully explained. Experimental results demonstrate that the proposed antenna has a −15 dB refection coefficient bandwidth covering the frequency range of 3.32–3.67 GHz. Additionally, it exhibits high port isolation (>35 dB), low cross polarization, high gain, and excellent total efficiency (>85%).

Resonant MEMS Accelerometer with Low Cross-Axis Sensitivity-Optimized Based on BP and NSGA-II Algorithms.

This article proposes a low cross-axis sensitivity resonant MEMS(Micro-Electro-Mechanical Systems) accelerometer that is optimized based on the BP and NSGA-II algorithms. When resonant accelerometers are used in seismic monitoring, automotive safety systems, and navigation applications, high immunity and low cross-axis sensitivity are required. To improve the high immunity of the accelerometer, a coupling structure is introduced. This structure effectively separates the symmetric and antisymmetric mode frequencies of the DETF resonator and prevents mode coupling. To obtain higher detection accuracy and low cross-axis sensitivity, a decoupling structure is introduced. To find the optimal dimensional parameters of the decoupled structure, the BP and NSGA-II algorithms are used to optimize the dimensional parameters of the decoupled structure. The optimized decoupled structure has an axial stiffness of 6032.21 N/m and a transverse stiffness of 6.29 N/m. The finite element analysis results show that the sensitivity of the accelerometer is 59.1 Hz/g (Y-axis) and 59 Hz/g (X-axis). Cross-axis sensitivity is 0.508% (Y-axis) and 0.339% (X-axis), which is significantly lower than most resonant accelerometers. The coupling structure and optimization method proposed in this paper provide a new solution for designing resonant accelerometers with high interference immunity and low cross-axis sensitivity.

Design of Miniaturized and Wideband Four-Port MIMO Antenna Pair for WiFi.

A miniaturized and wideband four-port multiple-input multiple-output (MIMO) antenna pair for Wi-Fi mobile terminals application is proposed. The proposed antenna pair consists of four multi-branch antenna elements arranged orthogonally, with an overall size of 40 × 40 × 3.5 mm3 and each antenna element size of 15.2 × 3.5 mm × 0.8 mm3. The performance of the proposed antenna shows the advantages of a wide frequency band, low mutual coupling, high efficiency, and a compact structure. The wideband characteristics of the antenna elements are achieved through multi-mode resonance. The suppression of coupling is accomplished by strategically positioning the four compact antenna elements to ensure their maximum radiation directions are orthogonal, thus eliminating the need for an additional decoupling structure. In this paper, the proposed antenna is optimized in terms of the parameters then simulated and measured. The simulated results illustrate that an impedance bandwidth of the antenna is about 15% (5.06~5.88 GHz) with S11 < -10 dB, excellent port isolation exceeds 20 dB between all ports, a high radiation efficiency ranges from 51.2% to 89.9%, the maximum gain is 4.5 dBi, and the ECCs are less than 0.04. The measured results show that the -10 dB impedance bandwidth of the antenna is about 13% (5.13~5.80 GHz), the isolation between the antenna elements is better than 21 dB, the radiation efficiency ranges from 51.8% to 92.3%, the maximum gain is 5.3 dBi, and the ECCs are less than 0.05. The proposed four-port MIMO antenna works on the 5G LTE band 46 and Wi-Fi 6E operating bands. As a mobile terminal antenna, the proposed design scheme demonstrates excellent performance and applicability, fulfilling the requirements for 5G mobile terminal applications.

Wideband high gain metasurface-based 4T4R MIMO antenna with highly isolated ports for sub-6 GHz 5G applications

This study presents the design of four 178×178\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$178\ imes 178$$\\end{document} (mm)2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{2}$$\\end{document} wideband, high gain, highly efficient metasurface-based 4T4R MIMO (Multiple-Input Multiple-Output) antennas with highly isolated ports, covering the middle and a portion of the upper bands of the sub 6 GHz 5G frequency spectrum for 5G-based systems, such as IoT (Internet of Things) applications, vehicular communications (e.g., rooftop antennas of cars or trains), smart industries (e.g., farms and factories). The radiating elements of these antennas use the aperture-coupled feeding technique with a dumbbell-shaped slot, a truncated square patch with two U-shaped slots, and a metasurface layer. The proposed MIMO structures place four identical radiating elements like a 2×2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$2\ imes 2$$\\end{document} matrix with 90∘\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$90^\\circ$$\\end{document} successive rotations to produce orthogonal electromagnetic waves, improving the isolation between ports. Six-millimeter spaces are added between these elements, and two vertical and horizontal strip slots are carved on the ground as the decoupling structure to decrease the mutual coupling. Simulation results show that Antenna_1, Antenna_2, and Antenna_3 achieve gain values of 6.2 to 9.4 dBi, 8.2 to 11.6 dBi, 6.2 to 9.5 dBi, below − 35, − 25, and − 33 isolation and almost 10 dB diversity gain from 2.8 to 4.7 GHz, 2.8 to 4.5 GHz, and 2.7 to 4.9 GHz, respectively. As a prototype, Antenna_4 is manufactured, and measurements are performed. It achieves 6.28 to 10.45 dBi gain values, below − 23 dB isolation, and 0.001 envelope correlation coefficient over 2.7 to 4.3 GHz. The results confirm that the proposed MIMO antennas are compatible with the 5G essential requisites.

A compact double‐sided four‐port printed antenna with pattern and polarization diversity for super‐wideband applications

SummaryA compact, double‐sided four‐port printed antenna with pattern and polarization diversity performance is proposed for super‐wideband (SWB) applications. The proposed printed antenna consists of microstrip line‐fed corner truncated four identical square patches. One pair of patches is placed strategically on the top side of the substrate, and another pair is on the bottom side with rotational symmetry to realize a compact four‐port antenna with higher port isolation (&gt;25 dB) throughout the operating band along with pattern diversity. A half‐circular slit is etched in the partial ground plane of all four antennas to achieve SWB (1–19.81 GHz) response. A meander‐shaped decoupling structure is incorporated on both sides of the substrate to enhance the port isolation. T‐shaped slots on the patch and corner truncations are conceived to achieve circular polarization (CP) across 5.15–5.83 GHz. The beauty of this structure lies in the easy switching between LHCP and RHCP by just controlling the port excitation. Moreover, the strategic placement of antenna elements produces bidirectional patterns with proper choice of port excitation. A good agreement is observed between the measured and simulation results.

Introduction of the orthogonal mode via the polarization conversion parasitic structure for the isolation enhancement of MIMO patch antennas

Abstract In this study, a high-isolation multiple-input multiple-output (MIMO) microstrip patch antenna (MPA), which utilizes an orthogonal mode cancellation method is proposed. This method employs TM10 and TM01 modes, which are simultaneously excited in the rectangular passive MPA. Initially, a rectangular decoupling structure featuring polarization rotation characteristics is designed. Further studies show that by loading the polarization conversion parasitic structure (PCPS), the electric field of the spatial coupling wave can be transformed from the x-polarized TM10 mode to the y-polarized TM01 mode. Therefore, TM10 and TM01 modes from the excited antenna and decoupling structure are concurrently coupled to the passive antenna, forming an evident weak-field region on the passive antenna. Placing the feeding probe of the passive MPA within the weak-field region prevents signal reception at the port. Consequently, this results in an extremely low mutual coupling of −49 dB at a resonant frequency of 5.8 GHz. Finally, a prototype of the proposed antenna is fabricated and tested, and the measured results closely match the simulated results. Additionally, it is observed that PCPS slightly influences the performance of the MIMO antenna.

Low mutual coupling miniaturized dual-band quad-port MIMO antenna array using decoupling structure for 5G smartphones

Maintaining the compactness of 5G smartphones while accommodating millimeter-wave (mm-wave) bands presents a significant challenge due to the substantial difference in frequency. To tackle this issue, we introduce a miniaturized quad-port dual-band multiple-input, multiple-output (MIMO) antenna with low mutual coupling (MC) and a considerable frequency difference. This quad-port MIMO antenna, built on a Rogers TMM4 substrate, measures 17.76 × 17.76 mm2 and boasts a dielectric constant of 4.5. It incorporates four planar patch antennas, positioned at the corners in perpendicular orientations. For dual-band operation at 28/38 GHz, each antenna element features a rectangular patch with four rectangular slots, complemented by a full ground plane. The spacing between these elements is 0.5 λo, and we've included a decoupling structure (DS) to minimize mutual coupling (MC) among the MIMO antenna elements with minimal complexity and cost. Simulation and measurement results reveal a significant reduction in mutual coupling between the array elements, ranging from − 25 to − 60 dB. As a result, we’ve developed the envelope correlation coefficient (ECC) and made advancements in the total active reflection coefficient (TARC), mean effective gain (MEG), and diversity gain (DG). The measured gains for this design are approximately 8.9 dBi at both 28 GHz and 38 GHz, with a radiation efficiency of nearly 93%. Furthermore, specific absorption rate (SAR) analysis confirms the MIMO antenna's suitability for smartphone handsets operating within the target frequency band.

A Partially Reflective FSS-Based Superstrate as a Decoupling Structure for Reducing the Mutual Coupling of Circularly Polarized Antennas

A Partially Reflective FSS-Based Superstrate as a Decoupling Structure for Reducing the Mutual Coupling of Circularly Polarized Antennas

Design and analysis of ultra‐wideband decoupling structure based on polarization mismatch

AbstractIn this work, a polarization rotating surface is designed, analyzed, and applied to the decoupling of ultra‐wideband antennas. A method of using dual‐size combined rings is proposed to expand the operating bandwidth to 4.8 to 18.2 GHz, and the polarization conversion rate within the entire bandwidth is higher than 99%. Based on the principle of polarization mismatch, placing the polarization rotating surface between ultra‐wideband antennas for decoupling can reduce the coupling between antennas by an average of 20 dB within the operating bandwidth. Simulation and experimental results consistently prove its excellent decoupling capabilities and ultra‐wide operating bandwidth.

CPW-Fed UWB-MIMO Antenna with Triple-band Notched and High Isolation using Double Y-shaped Decoupling Structure

A ultra-wideband (UWB) multiple-input-multiple-output (MIMO) antenna using double Y-shaped decoupling structure with high isolation and triple notched-band is presented. The designed antenna composed of two orthogonally placed monopole elements, coplanar ground and double Y-shaped branch. The defected substrate structure is used to achieve miniaturization. By slotting successively C-shaped slot, semi-circular slot and rectangular slot on the radiation patch and the ground, achieved three notched bands at 3.5 GHz WiMAX, 5.25 GHz WLAN, and 7.5 GHz X-band. The proposed antenna can operate in range of 2.56-12 GHz with triple notched bands of 3.31-3.96 GHz, 4.58-5.67 GHz and 6.57-8.16 GHz. Considering all the results, it can be concluded that the antenna presented has a great performance in terms of good radiation, high isolation (&gt;24 dB), a low level ECC (&lt;0.01) and a high DG level (&gt;9.99), which proves the presented antenna has good prospect in UWB-MIMO systems.

The design and decoupling of TX/RX antenna with omnidirectional conical beam operating at V band

Abstract In this work, a high isolation transmitter–receiver antenna with omnidirectional conical beam operating at 61.5 GHz is presented. The proposed dual-antenna system consists of a transmitter (TX) antenna and a receiver (RX) antenna with the same structure, composed of a circular metal patch with ring slot and metal shorting vias, fed by a coaxial probe at their respective geometric center. And both antennas are placed on a circular metal platform, positioned symmetrically with each other. To increase the isolation between them, three different decoupling methods are proposed, and the one with an electromagnetic band gap (EBG) structure added in-between shows the most promising decoupling effect, as the surface wave current can be maximally suppressed. The overall size of the antenna system is 2.2552 × π × 0.579 λ 0 3, where λ 0 is the free space wavelength at 61.5 GHz. A prototype of the proposed antenna system with EBG decoupling structure is fabricated and measured, demonstrating that the TX–RX isolation is 57.9 dB at 61.5 GHz, 21.6 dB better than that without decoupling structure, with omnidirectional conical beam radiation achieved at the same time.

Patch antenna mutual coupling reduction using a genetic algorithm

Many modern telecommunication systems use antenna arrays for beamforming, and data rates increase. Mutual coupling between antennas negatively affects such systems' performance, so reducing the mutual coupling is a relevant research topic. This paper aims to cover a program development for the automated synthesis of decoupling structures between printed radiators. The results of the synthesis of printed structures for the reduction of mutual coupling between microstrip antennas placed on one dielectric substrate have been presented. Several structures that reduce the mutual coupling between antenna elements have been designed using a genetic algorithm. The developed program allows decoupling structure synthesis automation using numerical modelling methods. While synthesizing the decoupling structures, the directional properties of the received two-element antenna arrays have been considered.

Isolation enhancement of distinct element dual polarized compact MIMO antenna for 5G/WLAN application

AbstractA novel‐shaped dual‐polarized low‐profile multiple‐input multiple‐output (MIMO) antenna with high isolation is proposed for 5G/WLAN application. An 8‐element MIMO antenna design comprises two unique planar radiators (chamfer, circular). Each radiator has dual feed and dual polarization characteristics. The prototype is fabricated with an FR‐4 dielectric substrate. A decoupling structure maintains desirable isolation for self‐isolated elements (−12 dB) using substrate integrated waveguide stubs between inter‐ports and high isolation among the adjacent radiating elements (−15 dB). The simulation was performed by using CST microwave studio. The simulated results of the proposed MIMO antenna are compared with the measurement results. Furthermore, ECC and DG are investigated.

Characteristics mode analysis based wideband Sub-6 GHz flexible MIMO antenna using a unique hybrid decoupling structure for wearable applications

This article presents a compact flexible four-element multiple input multiple output (MIMO) antenna for Sub-6 GHz wearable applications. A wideband monopole antenna with a modified edge tapered radiator and a lowered ground plane is replicated to form a four-element antenna. The proposed antenna is fabricated on a flexible polyethylene terephthalate (PET) substrate and holds an overall dimension of 65 × 56 × 0.25 mm3. The antenna has a measured bandwidth of 3.55–5.3 GHz with a peak gain of 4.9 dBi. A novel hybrid decoupling structure with a neutralization line in the radiator and a unique defective ground structure (DGS) suppresses the coupling current and provides isolation better than −24 dB throughout the bandwidth. The antenna design evolution is explained using characteristics mode analysis (CMA). The MIMO diversity performance is relatively good with MIMO diversity metrics showing envelope correlation coefficient (ECC) < 0.001, diversity gain > 9.99, total active reflection coefficient (TARC) < −10 dB, channel capacity loss (CCL) < 0.3 bps Hz−1 and multiplexing efficiency (ME) < −0.5. Specific absorption rate (SAR) analysis of the antenna is performed to check the antenna’s suitability in wearable applications and the proposed antenna exhibits 0.745 W kg−1 and 0.326W kg−1 for 1g and 10g of tissue respectively which is much less than the permissible international standards.

Dual-band independently tunable 8-element MIMO antenna for 5G smartphones

In this paper, a multi-input multi-output (MIMO) antenna for future mobile phone applications operating in sub-6 GHza using a novel combination of an E-shaped slot placed on the ground plane and an F-shaped probe is used to achieve a dual-band independently tunable antenna. The proposed antenna is not only self-isolated but it has also effectively achieved high isolation of greater than 17 dB in both 3.5 GHz (3.4 – 3.6 GHz) and 4.7 GHz (4.6 – 4.87 GHz) frequency bands for 8-element MIMO antenna configuration for 5G smartphones. The simple yet compact size of (0.035 λ0▪ 0.23 λ0), of the slot antenna produces a balanced slot mode which not only reduces the ground effects but also improves the isolation between two adjacent input ports. The novelty of the proposed dual-band MIMO antenna is its independent control of each band across a wide frequency band and results demonstrate higher efficiency (64% – 71%) and diversity gain performance in both frequency bands. Furthermore, the antenna is designed by the meticulous configurations of 8-antenna elements without employing any external decoupling structure to attain the desired polarization diversity. The prototype of this 8-element MIMO antenna is also fabricated and measured to validate its simulated performance. The simple structure of the proposed design and high efficiency makes it a promising candidate for 5G smartphones.

A large-scale MIMO antenna system for 5G IoT applications.

A multiple-input-multiple-output (MIMO) antenna system with low-profile and small element spacing characteristics is presented in this paper. This antenna contains multiple elements arranged in both E-plane and H-plane configurations. The original strong coupling between the MIMO elements can be suppressed by exciting orthogonal operating modes. To achieve this, a half-wavelength microstrip line and a quarter-wavelength grounded stub are utilized to decouple the H- and E-plane MIMO arrays. A 2 × 2 antenna prototype is fabricated and measured to demonstrate the decoupling concept's feasibility. The measured impedance bandwidth is from 4.78 to 4.81 GHz. Across this band, the isolation is better than 15 dB with extremely small edge-to-edge distances of 0.032λ and 0.026λ in the E- and H-plane, respectively. Featuring the simple decoupling structure, small element spacing, and the capability of extending to a large-scale 2 × N array, the proposed antenna can be used for 5G Internet of Things (IoT) applications operating at the N79 frequency band.