Curcas Methyl Ester Research Articles

Catalytic Conversion of Jatropha curcas Oil to Biodiesel Using Mussel Shell-Derived Catalyst: Characterization, Stability, and Comparative Study

Biodiesel represents a promising solution for sustainable energy needs, offering an eco-friendly alternative to conventional fossil fuels. In this research, we investigate the use of a catalyst derived from mussel shells to facilitate biodiesel production from Jatropha curcas oil. Our findings from X-ray Fluorescence (XRF) analysis emphasize the importance of carefully selecting calcination temperatures for mussel shell-based catalysts, with 1100 °C identified as optimal for maximizing CaO content. We identify a reaction time of 6 h as potentially optimal, with a reaction temperature of approximately 110 °C yielding the desired methyl ester composition. Notably, a methanol-to-oil ratio of 18:1 is the most favorable condition, and the optimal methyl ester composition is achieved at a calcined catalyst temperature of 900 °C. We also assess the stability of the catalyst, demonstrating its potential for reuse up to five times. Additionally, a thorough analysis of J. curcas Methyl Ester (JCME) biodiesel properties confirmed compliance with industry standards, with variations attributed to the unique characteristics of JCME. Comparing homogeneous (NaOH) and heterogeneous (CaO) catalysts highlights the potential of environmentally sourced heterogeneous catalysts to replace their homogeneous counterparts while maintaining efficiency. Our study presents a novel approach to sustainable biodiesel production, outlining optimal conditions and catalyst stability and highlighting additional benefits compared with NaOH catalysts. Therefore, utilizing mussel shell waste for catalyst synthesis can efficiently eliminate waste and produce cost-effective catalysts.

Optimization of the process variables on biodegradable industrial lubricant basestock synthesis from Jatropha curcas seed oil via response surface methodology

The synthesis of biolubricants from renewable feedstocks is currently gaining attention. Over 95% of the market is comprised of lubricants made from petroleum. Due to their limited biodegradability and high eco-toxicity, lubricants generated from petroleum constitute a significant environmental hazard. As pollution levels increase and oil supplies decline, there is a rising need to develop biobased alternatives. Manufacturing cleaner fuel products will mitigate the negative environmental impact of greenhouse gas emissions, which contribute to global warming. Jatropha curcas seed oil is an efficient renewable feedstock for biolubricant synthesis. This study optimized the process variables on biodegradable lubricant basestock production from J. curcas seed oil. A central composite design was used to maximize the chemical interaction between J. curcas methyl ester and ethylene glycol (EG) as a polyol. A total of 20 experimental runs were done to examine reaction temperature, time, and the ethylene glycol to fatty acid methyl ester (EG-to-FAME) molar ratio. A statistical model indicated that the maximum conversion yield of jatropha biolubricant (JBL) would be 92.48% under the following optimum reaction conditions: 128.95°C, 202.40 min, and ethylene glycol to fatty acid methyl ester (EG-to-FAME) molar ratio of 3.87:1. At these optimum conditions, an average jatropha biolubricant (JBL) yield of 94.12% was achieved under experimental conditions, and this value was well within the range predicted (92.48%) by the model. The quadratic model predicted the biolubricant output (R2 = 0.9919). The synthesized biolubricant met the requirements of Viscosity Grade 46 (ISO VG 46) set by the International Organization for Standardization.

Production and comparative fuel properties of biodiesel from non-edible oils: Jatropha curcas, Sterculia foetida and Ceiba pentandra

Biodiesel production from non-edible vegetable oil is one of the effective ways to overcome the problems associated with energy crisis and environmental issues. The non-edible oils represent potential sources for future energy supply. In this study, the physical and chemical properties of crude Jatropha curcas oil (CJCO), crude Sterculia foetida oil (CSFO) and crude Ceiba pentandra oil (CCPO) and its methyl ester have been studied. The acid values of three oils were found to be 12.78mg KOH per g, 5.11mg KOH per g and 11.99mg KOH per g which required acid-esterification and alkali-transesterification process. Acid value was decreased by esterification process using sulfuric acid anhydrous (H2SO4) as a catalyst and alkaline (NaOH) catalyst transesterification was carried out for the conversion of crude oil to methyl esters. The optimal conditions of FAME yield achieved for those three biodiesel were 96.75%, 97.50% and 97.72% respectively. Furthermore, the fuel properties of J. curcas methyl ester (JCME), S. foetida methyl ester (SFME) and C. pentandra methyl ester (CPME) were determined and evaluated. As a result, those produced biodiesel matched and fulfilled ASTM 6751 and EN 14214 biodiesel standards. Based on the results, JCME, SFME and CPME are potential non-edible feedstock for biodiesel production.