Cr Concentration Research Articles

Speciation of toxic metals in metal finishing filter cake by X-ray absorption spectroscopy

The speciation of Cr, Zn, Cu and Pb in two metal finishing filter cakes (TX and ST) was investigated by X-ray absorption spectroscopy (XAS) complemented by X-ray fluorescence (XRF) and X-ray diffraction (XRD). XRF showed that concentrations of Cr, Zn, Cu and Pb were 1.4%, 0.19%, 0.20% and 0.01%, respectively, in TX, and 12.6%, 3.3%, 1.3% and 0.21% in ST. No crystalline phases were detected in TX by XRD whereas ST was dominated by calcite. Cr and Fe K edge XAS showed Cr to be trivalent and octahedrally coordinated, co-precipitated with Fe as CrxFe1-x-(oxy)hydroxides in both filter cakes. Zn, P and Ca K edge XAS showed that 2ZnCO3∙3Zn(OH)2 and Zn3(PO4)2 were the dominant zinc-containing phases, with combined tetrahedral and octahedral coordination; Zn phases were slightly more crystalline in TX than ST. Pb L3 edge X-ray absorption near edge spectroscopy (XANES) found that Pb was likely adsorbed on amorphous SiO2. Cu, Si and S K edge XAS showed that all Cu was divalent, and the dominant copper phases were found to be Cu2Cl(OH)3, Cu(OH)2 and CuSO4·5H2O for ST, whereas Cu appeared to adsorb to amorphous SiO2 for TX, which contained much less Pb. Cr is thus immobilized in the filter cakes in a phase with low solubility at environmentally feasible pH values, whereas Zn, Cu and Pb could be released when the pH decreases below 8 or above 11. These findings are significant for the development of waste management regulations and/or metal recovery methods (e.g., hydro/pyrometallurgy).

Combined application of zinc oxide and iron nanoparticles enhanced Red Sails lettuce growth and antioxidants enzymes activities while reducing the chromium uptake by plants grown in a Cr-contaminated soil.

Soil contamination with chromium (Cr) is becoming a primary ecological and health concern, specifically in the Kasur and Sialkot regions of Pakistan. The main objective of the current study was to evaluate the impact of foliar application of zinc oxide nanoparticles (ZnO NPs) (0, 25, 50, 100 mg L-1) and Fe NPs (0, 5, 10, 20 mg L-1) in red sails lettuce plants grown in Cr-contaminated soil. Our results showed that both ZnO and Fe NPs improved plant growth, and photosynthetic attributes by minimizing oxidative stress in lettuce plants through the stimulation of antioxidant enzyme activities. At ZnO NPs (100 mgL-1), dry weights of shoots and roots and fresh weights of shoots and roots were improved by 53%, 58%, 34%, and 45%, respectively, as compared to the respective control plants. The Fe NPs treatment (20 mgL-1) increased the dry weight of shoots and the roots and fresh weights of shoots and roots by 53%, 76%, 42%, and 70%, respectively. Application of both NPs reduced the oxidative stress caused by Cr, as evident by the findings of the current study, i.e., at the ZnO NPs (100 mgL-1) and Fe NPs (20 mgL-1), the EL declined by 32% and 44%, respectively, in comparison with respective control plants. Moreover, Fe and ZnO NPs enhanced the Fe and Zn contents in red sails lettuce plants. Application of ZnO NPs at 100 mg L-1 and Fe NPs at 20 mg L-1, improved the Zn and Fe contents in plant leaves by 86%, and 68%, respectively, as compared to the control plants. This showed that the exogenous application of these NPs helped in Zn and Fe fortification in plants. At similar of concenteration ZnO NPs, CAT and APX activities were improved by 52% and 53%, respectively. Similarly, the POD contents were improved by 17% and 45% at 5 and 10 mg/L of Fe NPs. Furthermore, ZnO and Fe NPs limited the Cr uptake by plants, and the concentration of Cr in the leaves of lettuce was under the threshold limit. The exogenous application of ZnO NPs (100 mg L-1) and Fe NPs (20 mg L-1) reduced the Cr uptake in the leaves of red sails lettuce by 57% and 51%, respectively. In conclusion, ZnO and Fe NPs could be used for the improvement of plant growth and biomass as well as nutrient fortification in stressed environments. These findings not only underscore the efficacy of nanoparticle-assisted phytoremediation but also highlight its broader implications for sustainable agriculture and environmental health. However, future studies on other crops with molecular-level investigations are recommended for the validation of the results.

Corrosion Behavior of Ni-Cr Alloys with Different Cr Contents in NaCl-KCl-MgCl2

Corrosion Behavior of Ni-Cr Alloys with Different Cr Contents in NaCl-KCl-MgCl2

Wildfire Ashes from the Wildland-Urban Interface Alter Vibrio vulnificus Growth and Gene Expression.

Climate change-induced stressors are contributing to the emergence of infectious diseases, including those caused by marine bacterial pathogens such as Vibrio spp. These stressors alter Vibrio temporal and geographical distribution, resulting in increased spread, exposure, and infection rates, thus facilitating greater Vibrio-human interactions. Concurrently, wildfires are increasing in size, severity, frequency, and spread in the built environment due to climate change, resulting in the emission of contaminants of emerging concern. This study aimed to understand the potential effects of urban interface wildfire ashes on Vibrio vulnificus (V. vulnificus) growth and gene expression using transcriptomic approaches. V. vulnificus was exposed to structural and vegetation ashes and analyzed to identify differentially expressed genes using the HTSeq-DESeq2 strategy. Exposure to wildfire ash altered V. vulnificus growth and gene expression, depending on the trace metal composition of the ash. The high Fe content of the vegetation ash enhanced bacterial growth, while the high Cu, As, and Cr content of the structural ash suppressed growth. Additionally, the overall pattern of upregulated genes and pathways suggests increased virulence potential due to the selection of metal- and antibiotic-resistant strains. Therefore, mixed fire ashes transported and deposited into coastal zones may lead to the selection of environmental reservoirs of Vibrio strains with enhanced antibiotic resistance profiles, increasing public health risk.

Source identification and driving factor apportionment for soil potentially toxic elements via combining APCS-MLR, UNMIX, PMF and GDM

The contamination and quantification of soil potentially toxic elements (PTEs) contamination sources and the determination of driving factors are the premise of soil contamination control. In our study, 788 soil samples from the National Agricultural Park in Chengdu, Sichuan Province were used to evaluate the contamination degree of soil PTEs by pollution factors and pollution load index. The source identification of soil PTEs was performed using positive matrix decomposition (PMF), edge analysis (UNMIX) and absolute principal component score-multiple line regression (APCS-MLR). The geo-detector method (GDM) was used to analysis drivers of soil PTEs pollution sources to help interpret pollution sources derived from receptor models. Result shows that soil Cu, Pb, Zn, Cr, Ni, Cd, As and Hg average content were 35.2, 32.3, 108.9, 91.9, 37.1, 0.22, 9.76 and 0.15 mg/kg in this study area. Except for As, all are higher than the corresponding soil background values in Sichuan Province. The best performance of APCS-MLR was determined by comparison, and APCS-MLR was considered as the preferred receptor model for soil PTEs source distribution in the study area. ACPS-MLR results showed that 82.70% of Cu, 61.6% of Pb, 75.3% of Zn, 91.9% of Cr and 89.4% of Ni came from traffic-industrial emission sources, 60.9% of Hg came from domestic-transportation emission sources, 57.7% of Cd came from agricultural sources, and 89.5% of As came from natural sources. The GDM results showed that distance from first grade highway, population, land utilization and total potassium (TK) content were the main driving factors affecting these four sources, with q values of 0.064, 0.048, 0.069 and 0.058, respectively. The results can provide reference for reducing PTEs contamination in farmland soil.

Ultrahigh-temperature crustal anatexis and final cratonization in Eastern Hebei, North China Craton: Insights from ca. 2.46 Ga Taipingzhai enderbites

Charnockitic rocks are a suite of granulite-facies plutonic rocks that include dominantly granitic−tonalitic and partly dioritic rocks. The Na-rich endmembers of the charnockite series, including dioritic to tonalitic rocks, are also termed enderbites. Charnockitic rocks are the main component of the cratonic-type lower continental crust in Precambrian cratons worldwide. These rocks are generally considered to be products of the anatexis of the lower crust under high- to ultrahigh-temperature conditions and play a key role in stratification between upper and lower crustal layers as well as the cratonic stabilization (cratonization) of Precambrian continents, although further study is required to gather detailed information about these rocks. In this study, a group of igneous enderbites (dioritic−tonalitic charnockites) from Eastern Hebei, North China Craton, is investigated. Zircon U-Pb dating reveals that the enderbites formed at ca. 2.46 Ga, which is coeval with the regional granulite-facies metamorphic overprinting. The enderbites are primarily composed of clinopyroxene, orthopyroxene, plagioclase, and quartz, with minor amphibole, biotite, K-feldspar, and Fe-Ti oxides. The rocks are characterized by high Fe2O3T + MgO (9.80−15.9 wt%), Cr (71.0−292 ppm), and Ni (41.2−107 ppm) contents, as well as low Al2O3 (13.9−16.6 wt%) and K2O (1.07−2.43 wt%) contents, with high Na2O/K2O ratios (1.51−4.43) and low Sr/Y (24.5−49.5) ratios. Moreover, these rocks are enriched in light rare earth elements (LREEs), (La/Yb)N = 8.06−17.8, and yield weak Eu anomalies, (Eu/Eu* = 0.80−1.18), with negative Th, U, Ta, Nb, and Ti anomalies. Various mineral thermobarometers, oxybarometers, and hydrometers are used to constrain the crystallized P-T-ƒO2-H2O conditions of the enderbites. These rocks crystallized at high temperature (860−1000 °C), crystallization pressure (8.0 ± 1.0 kbar), and H2O-poor (1.5−2.4 wt%) conditions, with oxygen fugacities (ΔQFM) of 0.0−3.0, which suggests “hot” (high-temperature) and “dry” (water-poor) crystallization conditions. The enderbites also have heterogeneous in situ zircon Hf-O isotopic compositions: εHf(t) = 2.4−7.5; δ18O = 5.78‰−7.74‰. These new data, combined with trace element characteristics, suggest that the enderbites were derived from the partial melting of metabasites, and that assimilation and fractional crystallization controlled the compositional variation in the enderbites. Further thermodynamic and geochemical modeling suggests that the anatexis of Mg-Fe−rich metabasite under ultrahigh-temperature (>1000 °C) and H2O-poor (1.0−1.5 wt%) conditions at a low crustal depth (∼9.0 kbar) could yield a melt composition comparable to that of the observed enderbites. Postcollisional lithospheric extension and mafic magma underplating prompted the partial melting of lower crustal metabasite at ultrahigh temperatures and normal lower crustal depths, resulting in the formation of enderbites. This study demonstrates that the enderbites could be formed by ultrahigh-temperature anatexis of metabasite with amphibole dehydration melting (Pl + Amp → Opx + Cpx + melt) and offers robust evidence of the genetic links between the ultrahigh-temperature anatexis of basic rocks and the generation of enderbites. In addition, the occurrence of ca. 2.46 Ga enderbites may mark the final cratonization of the North China Craton, and the ca. 2.50−2.45 Ga tectono-thermal event was an ultrahigh-temperature metamorphic-anatexis process rather than simple regional granulite metamorphic overprinting. Therefore, the generation and emplacement of enderbites involved not only a magmatic process but also an element redistribution process in the lower crust, which has important implications for stabilization of the North China Craton at ca. 2.5 Ga.

Pre-oxidation of porous ferritic Fe22Cr alloys for lifespan extension at high-temperature

Pre-oxidation of porous ferritic Fe22Cr alloys was extensively studied in this paper. Weight gain measurements and SEM analysis revealed that pre-oxidation performed at 900°C for 40 min increased the lifespan of the alloy. A Cr evaporation study did not disclose any significant influence of the pre-oxidation process on the Cr content in the alloy. For a more detailed assessment, TEM imaging and X-ray tomography measurements of pre-oxidized samples were performed. These analyses showed that alteration in the grain and grain boundary diffusion fluxes might be the key for explaining the corrosion prevention role of pre-oxidation.

Restoration of the soil fertility under Cr(VI) and artificial drought condition by the utilization of plant growth-promoting Bacillus spp. SSAU2.

The study explores the potential of an indigenous halo-tolerant microbe identified as Bacillus spp. SSAU-2 in enhancing soil fertility and promoting plant growth for sustainable agricultural practices under the influence of multiple abiotic stresses such as Cr(VI), high salinity, and artificial drought condition. The study investigated various factors influencing IAA synthesis by SSAU-2, such as pH (5 to 11), salinity (10 to 50g/L), tryptophan concentration (0.5 to 1%), carbon (mannitol mand lactose), and nitrogen sources (peptone and tryptone). The highest IAA concentration was observed at pH 10 (1.695mg/ml) and pH 11 (0.782mg/ml). IAA synthesis was optimized at a salinity level of 30g/l, with lower and higher salinity levels resulting in decreased IAA concentrations. Notably, the presence of mannitol and lactose significantly augmented IAA synthesis, while glucose and sucrose had inhibitory effects. Furthermore, peptone and tryptone played a pivotal role in enhancing IAA synthesis, while ammonium chloride exerted an inhibitory influence. SSAU-2 showed a diverse array of capabilities, including the synthesis of gibberellins, extracellular polymeric substances, siderophores, and hydrogen cyanide along with nitrogen fixation and ammonia production. The microbe could efficiently tolerate 45% PEG-6000 concentration and effectively produce IAA in 15% PEG concentration. It could also tolerate high concentration of Cr(VI) and synthesize IAA even in 50ppm Cr(VI). The findings of this study provide valuable insights into harnessing the potential of indigenous microorganisms to promote plant growth, enhance soil fertility, and establish sustainable agricultural practices essential for restoring the health of ecosystems.

A Deep Learning Approach for Chromium Detection and Characterization from Soil Hyperspectral Data

High levels of chromium (Cr) in soil pose a significant threat to both humans and the environment. Laboratory-based chemical analysis methods for Cr are time consuming and expensive; thus, there is an urgent need for a more efficient method for detecting Cr in soil. In this study, a deep neural network (DNN) approach was applied to the Land Use and Cover Area frame Survey (LUCAS) dataset to develop a hyperspectral soil Cr content prediction model with good generalizability and accuracy. The optimal DNN model was constructed by optimizing the spectral preprocessing methods and DNN hyperparameters, which achieved good predictive performance for Cr detection, with a correlation coefficient value of 0.79 on the testing set. Four important hyperspectral bands with strong Cr sensitivity (400–439, 1364–1422, 1862–1934, and 2158–2499 nm) were identified by permutation importance and local interpretable model-agnostic explanations. Soil iron oxide and clay mineral content were found to be important factors influencing soil Cr content. The findings of this study provide a feasible method for rapidly determining soil Cr content from hyperspectral data, which can be further refined and applied to large-scale Cr detection in the future.

Spatial variability and source analysis of soil heavy metals: A case study of the key planting area of special agricultural products in Cangxi County, China.

Heavy metal pollution in farmland soil represents a considerable risk to ecosystems and human health, constituting a global concern. Focusing on a key area for the cultivation of special agricultural products in Cangxi County, we collected 228 surface soil samples. We analyzed the concentration, spatial distribution, and pollution levels of six heavy metals (Cr, Cu, Pb, Ni, Zn, and Hg) in the soil. Moreover, we investigated the sources and contribution rates of these heavy metals using Principal Component Analysis/Absolute Principal Component Scores (PCA/APCS) and Positive Matrix Factorization (PMF) models. Our findings indicate that none of the six metals exceeded the pollution thresholds for farmland soils. However, the mean concentrations of Cr and Ni surpassed the background levels of Sichuan Province. A moderate spatial correlation existed between Pb and Ni, attributable to both natural and anthropogenic factors, whereas Zn, Cu, Hg, and Cr displayed a strong spatial correlation, mainly due to natural factors. The spatial patterns of Cr, Cu, Zn, Pb, and Ni were similar, with higher concentrations in the northern and eastern regions and lower concentrations centrally. Hg's spatial distribution differed, exhibiting a broader range of lower values. The single pollution index evaluation showed that Cr and Ni were low pollution, and the other elements were no pollution. The average value of comprehensive pollution index is 0.994, and the degree of pollution is close to light pollution. Predominantly, higher pollution levels in the northern and eastern regions, lower around reservoirs. The PCA/APCS model identified two main pollution sources: agricultural traffic mixed source (65.2%) and natural parent source (17.2%). The PMF model delineated three sources: agricultural activities (32.59%), transportation (30.64%), and natural parent sources (36.77%). Comparatively, the PMF model proved more accurate and reliable, yielding findings more aligned with the study area's actual conditions.

A New Modified Carbon Paste Electrode for Selective Determination of Chromium(III) in Pharmaceutical Drugs and Food Samples

Background and Objective: This study presents a novel potentiometric method for the precise, accurate, selective, and rapid determination of Cr(III) ion concentration in different samples. Methods: A new ionophore, namely macrocyclic tetramide ionophore (MCTA), was synthesized through an inexpensive and straightforward approach, yielding a high-quality product. The (MCTA) ionophore was utilized as the active center in the preparation of modified carbon paste electrodes (MCPEs) to quantify the Cr(III) ion. The paste was made by adding graphite, MCTA, and plasticizer and mixing them in varying weight percent ratios. Results: The proposed electrodes, I and II, exhibited a trivalent Nernstian response of 20.029 ±0.57 and 20.3±0.56 mV decade-1 , respectively, with linearity of 1.0x10-7 – 1.0x10-2 and 1.0x10-5 – 1.0x10- 2 mol L-1 . Electrodes I and II were examined for their pH, response time, and thermal stability. In comparison to other mono-, bi-, and trivalent cations, starch, and sugars, the electrodes demonstrated a high degree of selectivity for Cr(III). The modified electrodes were used to determine the concentration of Cr(III) in various real samples, including drug tablets, juice extractions, and tap water, with acceptable recovery values. Conclusion: The results were compared with those obtained using the previously reported method, with no significant difference observed between them, as indicated by the F and t-test values. The data showed good accuracy and precision, as well as a high percentage of recovery. The adsorption capacity of the MCTA ionophore towards Cr(III) ions was also examined.

Concentrations of Bioelements (Zn, Cu, Fe, Cr, Mg, Mn) in Serum and Bone Tissue of Aging Men Undergoing Hip Arthroplasty: Implications for Erectile Dysfunction

Background: Erectile dysfunction (ED) stands out as one of the most prevalent sexual disorders in men, with its incidence progressively escalating with age. As delineated by the International Consultation Committee for Sexual Medicine on Definitions/Epidemiology/Risk Factors for Sexual Dysfunction, the prevalence of ED among men under 40 years is estimated to be within the range of 1–10%. The aim of this study was to determine the relationship between the concentration of bioelements (Zn, Cu, Fe, Cr, Mg, and Mn) in the serum and bone tissue and the concentration of selected hormones in men with and without erectile dysfunction. Materials and methods: The retrospective cohort study included 152 men who underwent total hip arthroplasty for hip osteoarthritis at the Department of Orthopaedic Traumatology and Musculoskeletal Oncology at the Pomeranian Medical University in Szczecin. Certain exclusion criteria were applied to ensure the integrity of the study. These included individuals with diabetes, a history of cancer, alcohol abuse, liver or kidney failure, New York Heart Association (NYHA) class III or IV heart failure, and those taking medications that affect bone metabolism, such as mineral supplements, neuroleptics, chemotherapeutic agents, immunosuppressants, corticosteroids, or antidepressants. Patients with hypogonadism or infertility were excluded from the study. Results: The study showed an association between bioT concentrations and Cu concentrations in both patients with and without erectile dysfunction. A correlation between bioactive testosterone and Cr concentrations was also observed in both groups. Patients with erectile dysfunction showed a relationship between bioT concentration and Zn concentration, TT concentration and Mn concentration, FT concentration and Zn concentration, and E2 concentration and Cr concentration. An analysis of elemental concentrations in bone tissue showed an association between FT and Mg and Mn concentrations, but only in patients with erectile dysfunction. In patients without erectile dysfunction, a correlation was observed between FT and Cu concentrations. A correlation was also observed between bioT concentrations and Mg, Mn, and Zn concentrations, but only in patients with erectile dysfunction. In patients without erectile dysfunction, a correlation was observed between bioT and Cu concentrations. Conclusions: Studying the relationship between the concentration of bioelements (Zn, Cu, Fe, Cr, Mg, and Mn) in the serum and bone tissue and the concentration of selected hormones in men may be important in explaining the etiology of the problem. The study of the concentration of Zn and Cu in bone tissue and serum showed that these two elements, regardless of the place of accumulation, may be related to the concentration of androgens in men.

Evaluation of heavy metal concentration in black tea and coffee marketed in Erbil, Iraq: a consumer health risk assessment

ABSTRACT Black tea and coffee are popular and widely consumed beverages worldwide. However, the potential accumulation of heavy metals in food products raises concerns regarding their toxicity. In this study, we investigated the concentrations of arsenic (As), cadmium (Cd), copper (Cu), chromium (Cr), lead (Pb), manganese (Mn), zinc (Zn), and iron (Fe) in 102 samples of black tea and coffee purchased from Erbil city market in Iraq. Additionally, we determined the Hazard Quotient (HQ) and Hazard Index (HI) levels of heavy metal intake to evaluate the non-carcinogenic health risks for adult consumers. The mean concentrations of As, Cd, Cu, Cr, Pb, Mn, Zn, and Fe in black tea and coffee were found to be 0.023, 0.11, 10.29, 0.60, 1.69, 294.99, 25.59, and 39.80 mg/kg, respectively. In the case of black tea, the highest mean concentration observed was 607.28 mg/kg for Mn, while the lowest was 0.035 mg/kg for Cd in coffee. Arsenic was below the detection limit in coffee. Our results revealed that, except for Cd content in some tea samples, the concentrations of the studied metals were within the standard levels. The HQ and HI values for all elements were found to be less than one, indicating no adverse health effects associated with consuming these beverages. However, continuous monitoring is essential to ensure the ongoing safety of black tea and coffee.

Cellular absorption and cytotoxic mitigation of heavy metals in mining vegetables in southwest China: Mechanistic insights and health implications

The existing health risk assessment models often rely on total concentrations of contaminants, neglecting cellular absorption, leading to an overestimation of risks due to a lack of toxicological verification. In this study, the content, bioaccessibility, and health risk evaluation of Cr, Ni, Cu, and As in vegetables from mining areas in Southwest China were examined. The cytotoxicity and gastric absorption of heavy metals and underlying mechanisms as well as the toxic mitigation approach after consumption of risky vegetables were explored. Our results showed that the heavy metals in cabbage, celery, and garlic seedlings were within the safety limit, even though grown in contaminated soils. The bioaccessibility of As, Cu, Ni, and Cr in vegetables in the gastric phase is from 6.92% to 81.15%, with mint having the highest bioaccessible concentrations of Cr (32.7 μg/kg), Cu (540.1 μg/kg), and As (103.9 μg/kg). The Hazard Quotient and Hazard Index values of the bioaccessible metals suggested an unacceptable cancer risk. Besides, the vegetable extracts increased cell apoptosis and tight junction disruption. Unexpectedly, the high-risk mint extract with the greatest bioaccessibility didn't cause cytotoxicity but inhibited cell apoptosis and enhanced cellular tight junction, evidenced by the upregulation of Zonula Occludens-1, Occludin, and Claudin 3, and a decrease in cellular heavy metal uptake. Furthermore, the mint extract could alleviate garlic seedling extract-induced cytotoxicity, indicating that the special substance in mint has protective effects. Taken together, special components in vegetables, cellular uptake, and toxicity of heavy metals should be considered in the accurate assessment of health risks.

Stabilization and Release Characteristics of Heavy Metals in Desulfurization Sludge from Coal-Fired Power Plants

ABSTRACT The leaching risk of heavy metals from flue gas desulfurization (FGD) by-product sludge of coal-fired power plants is high, and there is an urgent need for effective treatment using solidification. In this paper, dithiocarbonates (DTC), 2,4,6-tri-mercapto-S-triazine trisodium salt (TMT-15) curing agent, fly ash and cement were used to cure the desulfurization sludge and study the environmental release characteristics of heavy metals before and after curing. The results show that all four curing agents had a good curing effect. The best chelating agent was DTC, and the best curing conditions were achieved at a liquid-to-solid ratio of 3:1 and a mass fraction of 8%. The leaching concentrations of As, Pb, Cd, Cr, Ni, Cu, Zn, and Hg were reduced by 87.95%, 100%, 85.29%, 86.17%, 70.11%, 95.06%, 90.28%, and 98.44%, respectively, after curing. In the environmental release characteristics test, the leaching concentrations of heavy metals in the cured sludge were lower than those of the original samples at different pH values and temperatures, indicating better stability. The mass fraction had the greatest effect on the leaching concentration of heavy metals, followed by the pH value and temperature.

Screening for Antibiotic Resistance Genes in Bacteria and the Presence of Heavy Metals in the Upstream and Downstream Areas of the Wadi Hanifah Valley in Riyadh, Saudi Arabia

Valley surface water is considered a focal public health concern owing to the presence of multi-drug-resistant bacteria. The distribution of antimicrobial resistance (AMR) bacteria in the surface water is affected by the presence of multiple factors, including antibiotics coming from wastewater discharge or other contaminant sources such as pharmaceuticals, biocides, and heavy metals. Furthermore, there is evidence suggesting that high levels of antibiotic resistance genes (ARGs) can be transferred within bacterial communities under the influence of heavy metal stress. Hence, the primary aim of this study is to investigate the presence of heavy metals and bacterial ARGs in upstream as well as downstream locations of Wadi Hanifah Valley in Riyadh, Saudi Arabia. Sample collection was conducted at eighteen surface water sites within the valley in total. The selection of ARGs was associated with the most common antibiotics, including β-lactam, tetracycline, erythromycin, gentamicin, sulphonamide, chloramphenicol, vancomycin, trimethoprim, and colistin antibiotics, which were detected qualitatively using polymerase chain reaction (PCR) technology. The tested antibiotic resistance genes (ARGs) included (blaNDM-1 (for the antibiotic class Beta-lactamases), mecA (methicillin-resistant Staphylococcus aureus), tet(M) and tet(B) (for the antibiotic class Tetracycline), ampC (for the antibiotic class Beta-lactamases), vanA (for the antibiotic class vancomycin), mcr-1 (for the antibiotic class colistin), erm(B) (for the antibiotic class erythromycin), aac6′-Ie-aph2-Ia (for the antibiotic class Gentamicin), sulII (for the antibiotic class sulphonamide), catII (for the antibiotic class Chlorophincol), and dfrA1 (for the antibiotic class trimethoprim). Moreover, an assessment of the levels of heavy metals such as lithium (Li), beryllium (Be), chromium (Cr), cobalt (Co), arsenic (As), cadmium (Cd), tin (Sn), mercury (Hg), and lead (Pb) was conducted by using inductively coupled plasma mass spectrometry (ICPMS). According to our findings, the concentrations of sulphonamide, erythromycin, and chloramphenicol ARGs (erm(B), sulII, and catII) were observed to be the most elevated. Conversely, two ARGs, namely mecA and mcr-1, were not detected in the samples. Moreover, our data illustrated a significant rise in ARGs in the bacteria of water samples from the upstream sites as compared with the water samples from the downstream sites of Wadi Hanifah Valley. The mean concentration of Li, Be, Cr, Co, As, Cd, Sn, Hg, and Pb in the water samples was estimated to be 37.25 µg/L, 0.02 µg/L, 0.56 µg/L,0.32 µg/L, 0.93 µg/L, 0.01 µg/L, 200.4 µg/L, 0.027 µg/L, and 0.26 µg/L, respectively, for the selected 18 sites. Furthermore, it was revealed that the concentrations of the screened heavy metals in the water samples collected from various sites did not surpass the maximum limits set by the World Health Organization (WHO). In conclusion, this study offers a concise overview of the presence of heavy metals and ARGs in water samples obtained from the Wadi Hanifah Valley in Riyadh, KSA. Such findings will contribute to the ongoing monitoring and future risk assessment of ARGs spread in surface water.

An innovative ionic liquid-aqueous biphasic system for simultaneously highly efficient dechroming and collagen recovery from chrome-tanned leather shavings at room temperature

Chrome-tanned leather shavings (CTLS) with abundant collagen of 70–90 wt% but high Cr content of 2–4 wt% are considered as hazardous wastes. Due to the stable covalent bond between Cr and collagen, current processes for collagen recovery from CTLS face challenges including low dechroming efficiency, collagen disruption, high energy and chemical consumption and secondary pollution. In this paper, an innovative IL-targeted homogeneous isolation (IL-THI) process based on the reusable ionic liquid-aqueous biphasic system (IL-ABS) was established for the simultaneous resource recovery and complete dechroming of CTLS at room temperature, with the recovery rate of collagen reached 72.4 % while Cr content in collagen is reduced from 35.65 × 103 mg/kg to 1.78 mg/kg. This IL-ABS enriched TBAH in the upper phase and potassium tartrate in the lower phase. Moreover, TBAH demonstrated excellent reproducibility across five cycles, achieving consistently low Cr content of 2.65 mg/kg in collagen, far below the 50 mg/kg limit in national standards. The triple helix conformation and the molecular weight of the collagen product were confirmed via Fourier-transform infrared spectroscopy, X-ray diffraction analyses, circular dichroism spectra analysis and SDS-PAGE. Moreover, economic calculations demonstrated the suitability of this novel process for sustainable CTLS recovery. The superior dechroming ability of IL-ABS is attributed to the formation of Cr(III)-Tartrate complexes, which preferentially migrate to the lower phase due to the solvophobic effect, while dissolved collagen is recovered from the upper phase, as disclosed by UV–Vis spectra, ICP-OES, and all-atom molecular dynamics simulations. Additionally, IL-THI process demonstrates considerable potential for the isolation of Cr(III) and collagen in solid waste, with low energy consumption, improved separation efficiency, and increased design flexibility.

Influencing Factors, Risk Assessment, and Source Identification of Heavy Metals in Purple Soil in the Eastern Region of Guang’an City, Sichuan Province, China

Soil heavy metal contamination poses a significant threat to both environmental health and ecological safety. To investigate the influencing factors, ecological hazards, and sources analysis of heavy metals in purple soil, 27 sets of soil samples were collected from varying genetic horizons within Guang’an City, and the contents of As, Cd, Cu, Cr, Hg, Ni, Pb, and Zn were analyzed. The results indicated higher concentrations of heavy metals in soil A horizon, compared to that of C horizon. The relevance analysis indicated that the soil’s heavy metals were strongly correlated with the soil’s physicochemical properties. The enrichment factor, pollution load index, and potential risk index highlighted slightly to severely polluted levels of soil Cd and Hg, which significantly contribute to the ecological hazards posed by soil heavy metals. The potential source of heavy metals analyzed using the APCS-MLR model identified both anthropogenic inputs and natural sources as primary contributors to heavy metal presence in soils. The Cu, Cr, Ni, Pb, and Zn contents in the samples from different genetic horizons were chiefly influenced by natural sources, such as soil matrix erosion and weathering, while the concentrations of Cd and Hg were largely affected by anthropogenic activities, specifically coal combustion and agriculture. Conversely, the As content was found to be influenced by a combination of both factors. Anthropogenic activities greatly impacted soil heavy metals at various depths within the study area, thereby underscoring the importance of monitoring these heavy metals. The findings gained from this research can give a scientific basis for the potential utilization of purple soil.

Characterization of heavy metal contamination in wetland sediments of Bosten lake and evaluation of potential ecological risk, China

In November 2023, twenty-two sediment samples were collected from the Bosten Lake wetland in Xinjiang to determine the concentrations of eight heavy metals: arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), mercury (Hg), nickel (Ni), lead (Pb), and zinc (Zn). This data was used to assess heavy metal contamination and potential ecological risks in the sediments using the Pollution Load Index (PLI) and the Potential Ecological Risk Index (RI). Additionally, multivariate statistical analysis and Positive Matrix Factorization (PMF) were employed to elucidate potential sources and their contributions to contamination. The following are the main conclusions: (1) average concentrations of Zn, Cd, Cr, Pb, and Hg in the sediments surpassed Xinjiang soil background levels by factors of 1.01, 3.58, 1.32, 1.94, and 1.53, respectively. (2) Sediments demonstrated severe pollution with Cd, slight pollution with Zn, Cr, Pb, and Hg, while Cu and Ni indicated mild pollution and As showed non-polluted levels. The overall PLI average (1.01) suggested slight contamination. (3) The descending order of average single ecological risk values were Cd, Hg, Pb, Cu, Ni, Cr, As, and Zn, with a comprehensive RI averaging at 184.07, signaling a moderate ecological risk. (4) Source apportionment revealed that Zn, Cu, Pb, and Ni were influenced by transportation and household waste emissions, while Cr and As were dictated by natural background levels. Hg predominately originated from fossil fuel combustion and Cd from agricultural activities. (5) Mixed sources accounted for the following percentage contributions to sediment heavy metal content: transportation and domestic waste (30.41%), natural background (25.88%), fossil fuel combustion (22.40%), and agricultural activities (21.31%). With anthropogenic inputs exceeding those of natural origins, it is imperative to prioritize the management of Cd, Hg, and Pb as primary pollutants within the region.

Moss as a passive biomonitoring tool for the atmospheric deposition and spatial distribution pattern of toxic metals in an industrial city.

Anthropogenic pollution impacts human and environmental health, climate change, and air quality. Karabük, an industrial area from the Black Sea Region in northern Türkiye, is vulnerable to environmental pollution, particularly soil and air. In this research on methodological aspects, we analyzed the concentrations of six potential toxic metals in the atmospheric deposition of the city using the passive method of moss biomonitoring. The ground-growing terrestrial moss, Hypnum cupressiforme Hedw., was collected during the dry season of August 2023 at 20 urban points. The concentrations of Cr, Cu, Cd, Ni, Pb, and Co were determined in mosses by the ICP-MS method. Descriptive statistical analysis was employed to evaluate the status and variance in the spatial distribution of the studied metals, and multivariate analysis, Pearson correlation, and cluster analysis were used to investigate the associations of elements and discuss the most probable sources of these elements in the study area. Cd and Co showed positive and significant inter-element correlations (r > 0.938), representing an anthropogenic association mostly present in the air particles emitted from several metal plants. The results showed substantial impacts from local industry, manufactured activity, and soil dust emissions. Steel and iron smelter plants and cement factories are the biggest emitters of trace metals in the Karabük area and the primary sources of Cr, Cd, Ni, and Co deposition.