Corrosion Resistance Of Steel Research Articles

Steel corrosion resistance with new 2-mercaptopyrimidin-4-ol derivatives

Steel corrosion resistance with new 2-mercaptopyrimidin-4-ol derivatives

Protection of 316L Steel Against LBE Corrosion by a CaO-MgO-Al2O3-SiO2 Glass–Ceramic Coating

A CaO-MgO-Al2O3-SiO2 glass–ceramic coating was prepared by the slurry method and subsequent sintering to improve the corrosion resistance of 316L steel in liquid lead–bismuth eutectic alloy at high temperatures. The glass–ceramic coating, sintered at 884 °C, was dense and demonstrated strong adhesion to the substrate. It was composed of the crystalline phases diopside (CaMgSi2O6) and anorthite (CaAl2Si2O8) and had an average Vickers hardness of 595 HV, which was over three times that of 316L steel. After corrosion in an oxygen-saturated, static lead–bismuth eutectic alloy at 500 °C for 1000 h, the uncoated 316L experienced significant mass gain (0.04 g) due to severe oxidative corrosion, resulting in the formation of Fe3O4 and Pb2O on its surface. In contrast, the glass–ceramic-coated specimens showed a very small mass gain (0.0012 g) after corrosion. The coating maintained good thermal stability; its crystalline phase composition remained largely unchanged after the corrosion test. The glass–ceramic coating still exhibited dense microstructure and tightly adhered to the substrate after corrosion. There was no evident penetration of lead–bismuth into the coating, and no dissolution of the coating’s elements into the lead–bismuth alloy was detected. These observations confirm that the glass–ceramic coating possessed superior corrosion resistance in liquid lead–bismuth eutectic environments.

A Study of the Effect of Ultrasonic Assistance on the Microstructure and Corrosion Resistance of Laser-Welded P110 Steel

A Study of the Effect of Ultrasonic Assistance on the Microstructure and Corrosion Resistance of Laser-Welded P110 Steel

Corrosion of Steels in Liquid Bismuth–Lithium Alloy

The corrosion resistance of several types of steel (AISI 410, 321, 316L, 904L) was determined in a liquid Bi-Li (5 mol.%) alloy (BLA) medium at 650 °C combining gravimetric analysis of steel samples and chemical analysis of corrosion products’ content accumulating in the BLA phase. Energy dispersive X-ray spectrometry, scanning electron microscopy, X-ray fluorescence and inductively coupled plasma–atomic emission spectrometry analysis were employed for characterizing steel structure and alloy composition. AISI 321, 316L and 904L nickel-containing corrosion-resistant steels underwent severe corrosion in BLA, and their corrosion rates depended on the nickel content in the material. AISI 410 steel exhibited the lowest corrosion rate of all the materials investigated, and this type of steel can be considered as a reasonable structural material for work in BLA environments. The corrosion rates of AISI 410, 321, 316L and 904L steels in BLA at 650 °C were 77, 244, 252 and 280 µm/year, respectively. It was also found that chromium was etched more intensively than iron from the surface of steel samples.

Corrosion Resistance and Fracture Toughness of Cryogenic-Treated X153CrMoV12 Tool Steel

Abstract Cryogenic treatment can be employed as an additional heat treatment step for martensitic steels, particularly high-carbon and high-alloy tool steels, to improve their mechanical properties and wear resistance. This enhancement results from a transformation of retained austenite and precipitation of finely distributed secondary carbides. The present study examines the impact of a shallow cryogenic treatment, performed between the quenching and tempering processes, on the corrosion resistance and fracture toughness of cold work tool steel X153CrMoV12. The influence of the shallow cryogenic treatment was evaluated using potentiodynamic polarization test, salt spray tests and three-point bending tests in various hydrogen charging conditions. In addition, the microstructure and phase transformation of the tool steel were investigated using high-resolution scanning electron microscopy, X-ray diffraction and dilatometer tests. The results suggest that the shallow cryogenic treatment followed by a single tempering cycle can slightly enhance the corrosion resistance of the steel. More importantly, the shallow cryogenic treatment positively affects fracture toughness and reduces hydrogen susceptibility. It is discussed how these improvements in the properties of the X153CrMoV12 steel are linked to the microstructural changes induced by the shallow cryogenic treatment.

Enhancing wear and corrosion resistance of AISI410 stainless steel in simulated seawater environments through PVD sputtering of TiCrN and CrSiN coatings

Enhancing wear and corrosion resistance of AISI410 stainless steel in simulated seawater environments through PVD sputtering of TiCrN and CrSiN coatings

Effect of P Addition on the Corrosion Resistance of Steels before and after Rust Formation

Effect of P Addition on the Corrosion Resistance of Steels before and after Rust Formation

Durability and steel corrosion resistance of Fly ash-based geopolymer concrete exposed to water of Lake Qaroun

Durability and steel corrosion resistance of Fly ash-based geopolymer concrete exposed to water of Lake Qaroun

Passivation and depassivation of reinforcement steel in alkali-activated materials—A review

This paper reviews the formation and breakdown of passive film on the surface of reinforcement steel in alkali-activated materials (AAMs) considering the characteristics of reaction product and pore solution chemistry. The literature review shows that the pore solution of AAMs has higher concentrations of OH−, Na+, silica and aluminium compared to Portland cement (PC). This relatively high alkalinity contributes to the generation of a passive film, which has positive effects on the corrosion resistance of reinforcement steel embedded in AAMs. The silica-aluminium zeolite layer present on the surface of passive film adsorbs chloride ions and effectively inhibits chloride-induced depassivation. Generally, lower ratios of [Cl−]/[SO42−] and [Cl−]/[S2O32−] potentially inhibit the depassivation of reinforcement steel. The high pH value and the elevated concentrations of HS− of AAMs contribute to the increase of critical chloride content (Ccrit). However, the higher content of reduced sulfide mainly dissolved from slag results in the consumption of dissolved oxygen, which is necessary for the formation of passive film. Generally, the presence of reduced sulfide forms Fe-S complexes on the surface of reinforcement steel in AAMs. Even so, higher corrosion resistance for AAMs is mostly expected with longer depassivation time due to finer microstructure and lower chloride penetration rates compared to PC-based materials. The decrease in pH value in the pore solution of the AAMs is the main factor affecting carbonation-induced depassivation of reinforcement steel, while high concentrations of bicarbonate and carbonate ions inhibit depassivation.

Effect of Tempering Temperature on the Aqueous Corrosion Resistance of 9Cr Series Heat-Resistant Steel

In this investigation, the aqueous corrosion resistance of 9Cr series heat-resistant steel during tempering was investigated. Optical Microscopy (OM), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectrometer (EDS) were used to analyze the effect of tempering temperature on the microstructure and precipitation behavior of precipitates. The heat-resisting steel was heated to 1150 °C for 1 h, and then tempered at different temperatures between 680 °C and 760 °C for 2 h. The microstructure of the heat-resistant steel after tempering was composed of lath-tempered martensite and fine precipitates. The hardness decreased with increasing tempering temperature, ranging from HBW 261 to HBW 193. The aqueous corrosion resistance improved as the tempering temperatures increased from 680 °C to 720 °C but deteriorated at higher temperatures, such as 760 °C, which was obtained by an electrochemical corrosion performance test. The aqueous corrosion resistance was affected by the decrease in dislocation density and the decrease in Cr solution in the tempered martensite. With the increase in the tempering temperature, the aqueous corrosion potential first increases and then decreases, the self-corrosion current density first decreases and then increases, and the polarization resistance first increases and then decreases. Furthermore, the increase in corrosion resistance is attributed to the reduction in dislocation density and chromium depletion in the martensitic structure as the tempering temperature approaches 720 °C. This paper reveals the effect of tempering temperature on the corrosion resistance of 9Cr series heat-resistant steel, which is a further exploration of a known phenomenon.

Corrosion Behavior of 700L Automotive Beam Steel in Marine Atmospheric Environment.

The marine atmospheric corrosion behavior of 700L high-strength automotive beam steel exposed for 36 months was investigated by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, and electrochemical technology. The corrosion kinetics of 700L steel followed the exponential function: D = 4.85t1.23. The rust layers were mainly composited of γ-FeOOH, α-FeOOH, γ-Fe2O3, and Fe3O4, regardless of the exposure duration. With an extended exposure time, the porosity, cracking, and spalling of the rust layers increased, and the densification and thickness uniformity decreased. Electrochemical measurements displayed that the corrosion resistance of the rusted 700L steel gradually decreased with increasing exposure time. A good correlation was found between rust layer composition, microstructure, and corrosion resistance.

A 10-year study of the corrosion resistance of stainless steels used as reinforcement in chloride-contaminated concrete exposed to severe conditions

A 10-year study of the corrosion resistance of stainless steels used as reinforcement in chloride-contaminated concrete exposed to severe conditions

Enhancing high-temperature chloride molten salts corrosion resistance of 310S steel with Si-added Ni–Al coating

Ni–Al based coating is one of the common high temperature and corrosion resistant protective coatings. In the present paper, the effect of Si content on the formation of Al2O3 layer and the corrosion resistance of Ni–Al coating to chloride molten salt was studied. The research results show that the Ni–Al coatings with varying Si content mainly form NiAl2O4 and Al2O3 oxide layers after pre-oxidation, and form a three-layer structure after molten salt corrosion. The appropriate amount of Si added to the Ni–Al coating can promote the formation of the α-Al2O3 layer during pre-oxidation and thermal corrosion, improving the corrosion resistance of the coating to high temperature chloride molten salt, and hindering the diffusion of Cr elements. Particularly, the Ni–Al coating with Si content of 1.2 at.% has the thickest and densest Al2O3 protective layer, showing the best corrosion resistance. The simulation results shows that compared with the Ni–Al coating without Si, the Cl atoms in the Si-added Ni–Al coating need to overcome greater energy barriers to diffusion during the molten salt corrosion process, which also indicates that the addition of Si can improve the corrosion resistance of the coating.

Effect of rare earth Ce treatment on the microstructure and properties of 430 ferritic stainless steel bearing Sn and Cu

The effects of rare earth Ce on purifying molten steel, modifying inclusions and micro-alloying in 430 ferritic stainless-steel bearings with Sn and Cu has been studied in this paper. The results demonstrate that Ce can purify molten steel, modify inclusions, enhance the mechanical properties and improve the pitting and corrosion resistance of the experimental steel. Ce effectively purifies the molten steel, reducing the total oxygen (T. O) content to as low as 0.00086 wt.% and sulphur (S) content to 0.0020 wt.%. The transformation of inclusions in the steel follows the sequence of MnS·Al2O3 → CeAlO3 → Ce2O2S → Ce2O3 with increasing Ce content. The number of inclusions initially decreases and then increases, with the experimental steel containing 0.012 wt.% Ce showing the best cleaning effect. Additionally, Ce treatment only slightly improves the mechanical properties of the experimental steel, but significantly enhances its pitting corrosion resistance and intergranular corrosion resistance by changing the enrichment state of carbides and impurity elements at the grain boundaries. In detail, Ce can partially inhibit the precipitation of M23C6 type carbides at grain boundaries, thereby improving the intergranular corrosion resistance of the experimental steel.

Effects of Thermal Aging on Corrosion Resistance of Duplex Stainless Steel Fabricated by Different Methods

Effects of Thermal Aging on Corrosion Resistance of Duplex Stainless Steel Fabricated by Different Methods

A comprehensive investigation of oxygen/graphite carbon nitride smart Nano coatings for sustainable maintenance and sacrificial anode protection of mild steel

AbstractBACKGROUNDThis study enhancing the corrosion resistance of mild steel (MS) by incorporating photo‐catalyst‐doped graphitic carbon nitride (g‐C₃N₄) nano‐sheets containing silver (Ag) and oxygen (O₂) into a solar light‐active photoelectrochemical anticorrosion paint with polyester (PE). The objective is to provide sacrificial anode protection through visible light activation.RESULTSThe developed paint forms a uniform film on the MS surface, effectively providing anodic protection under visible light. Characterization techniques, including energy‐dispersive X‐ray spectroscopy (EDX), transmission electron microscopy (TEM), Fourier‐transform infrared spectroscopy (FTIR), and UV–Vis spectroscopy, confirm the molecular structure of the nano‐sheets. Corrosion resistance, assessed through weight loss measurements and open circuit potential (OCP) tests, shows significant improvement with the addition of Ag/g‐C₃N₄ and Ag‐O₂/g‐C₃N₄ nano‐sheets at an optimized concentration of 15 mg. The protection efficiency is ranked as follows: O₂‐g/C₃N₄ > O‐g/C₃N₄ > Ag‐O₂/g‐C₃N₄ > Ag‐g/C₃N₄ > g‐C₃N₄. After 28 days of immersion in seawater, MS coated with O₂/g‐C₃N₄ exhibited the least weight loss, with an inhibition efficiency of up to 99%. Electrochemical impedance spectroscopy (EIS) further demonstrated enhanced coating resistance for the O₂/g‐C₃N₄ coating (Rct = 3.76 kΩ.cm2, Rcoat = 1.69 kΩ.cm2) compared to pure PE (Rct = 0.005 kΩ.cm2, Rcoat = 0.096 kΩ.cm2).CONCLUSIONThe synthesized O₂/g‐C₃N₄ and Ag‐O₂/g‐C₃N₄ nano‐sheets exhibit high surface areas and enhanced water dispersibility, which contribute to significant corrosion protection of MS. The electrochemical performance, including weight loss and OCP measurements, highlights the potential of these nano‐sheet photo‐catalysts in advancing corrosion resistance technologies, with broad implications for materials science and engineering applications. © 2024 Society of Chemical Industry (SCI).

Improving Corrosion Resistance of Low Carbon Steel through Surface Mechanical Attrition Treatment Duration

Improving Corrosion Resistance of Low Carbon Steel through Surface Mechanical Attrition Treatment Duration

The effect of drying-wetting alternation on corrosion resistance of rusted weathering steel

In order to understand the effect of drying-wetting alternation on the corrosion resistance of rusted weathering steel, firstly, a rusted weathering steel was obtaioned through the preparation of stabilized rust layer on the surface of naked weathering steel; secondly, a cyclic corrosion test (CCT) of drying-wetting alternation with different cyclic periods was carried out for rusted weathering steel. With the extension of cyclic period in drying-wetting CCT, the corrosion resistance of rusted weathering steel increased from 0 cycle to 6 cycle and then decreased after 6 cycle, which was closely associated with the variations of composition and microstructure for stabilized rust layer during the process of drying-wetting CCT. From 0 cycle to 6 cycle, the increased corrosion resistance of rusted weathering steel was attributed to the abundance rise of α-FeOOH in the interior of stabilized rust layer; however, from 6 cycle to 20 cycle, the decreased corrosion resistance of rusted weathering steel was due to the partial destruction of crystal sturcuture for stabilized rust layer.

Effect of Boronizing on the Corrosion Resistance of Martensitic Stainless Steels

Effect of Boronizing on the Corrosion Resistance of Martensitic Stainless Steels

Effect of ultrasonic impact treatment on surface residual stress, microstructure and electrochemical properties of the hot-rolled S355 steel

The effects of ultrasonic impact treatment (UIT) on the microstructure, corrosion resistance, and surface residual stress of hot-rolled S355 steel were investigated. In addition, the improving mechanism of the UIT induced corrosion resistance was discussed. The results show that the UIT can effectively improve the corrosion resistance of hot-rolled S355 steel, and corrosion current density reduction is demonstrated. Based on the corrosion morphology, it can be found that after the UIT the corrosion pits became shallower, the oxide layer becomes denser, and more flocculent structures appear on the surface as well as the appearance of dense irregular curved structures. Moreover, the residual tensile stress on the surface of the hot-rolled S355 steel is transformed into residual compressive stress after the UIT. The grains are refined, and the microhardness is increased, which implied that the significant plastic deformation has occurred on the surface of the hot-rolled S355 steel. The findings confirm that dense oxides could be generated on the surface of hot-rolled S355 steel treated by ultrasonic impact since the residual compressive stress is introduced, the plastic deformation is induced, and the grains are refined.