Corrosion Resistance Of Alloy Research Articles

Influence of Low-Energy High-Current Electron Beam Exposure on the Phase Composition and Corrosion Resistance of the AM60 Magnesium Alloy

The surface of an AM60 (Al – 5.5, Zn – 0.2, Cu – 0.009, Fe – 0.005, Si – 0.1; Ni – 0.002, Mn – 0.3 wt.%, Mg – the rest) magnesium alloy was exposed to a low-energy high-current electron beam. After the irradiation, the content of the β-phase (Mg17Al12) decreases and the aluminum content increases in the alloy surface layer. After the exposure to the electron beam, the corrosion resistance of the alloy in a 1-molar NaCl solution increases significantly compared to the initial state. The physical reason for the increase in the alloy corrosion resistance after exposure to the electron beam is the higher corrosion resistance of the oxide film formed on the alloy surface due to the increased aluminum content.

Effects of Strontium Modification on Corrosion Resistance of Al-Si Alloys in Various Corrosive Environments

This study investigates the impact of strontium (Sr) additions on the corrosion resistance of an LM6 (A413) aluminium alloy. By incorporating varying concentrations of Sr (0.01 wt.% and 0.05 wt.%), the morphological and corrosion behaviours of the alloy were analysed under different corrosive environments, including sulphuric acid, sodium hydroxide, and sodium chloride solutions. The results demonstrate that Sr modifications significantly enhance the alloy’s corrosion resistance, with the most substantial improvement observed at 0.05 wt.% Sr. The analysis revealed that the weight loss of the alloy in sulphuric acid decreased by 2.5% with 0.05 wt.% Sr after 10 days of immersion, due to the formation of a stable passive oxide layer. In sodium hydroxide, however, the weight loss was reduced by 5% with 0.05 wt.% Sr after 10 days, indicating aggressive uniform corrosion. In the 3.5% sodium chloride solution, the corrosion rates remain relatively low, and the 0.05 wt.% Sr alloy showed a decrease in corrosion product formation over time, suggesting enhanced resistance. Detailed surface analyses, including 3D profiling and morphology assessments, revealed that Sr additions refine the eutectic silicon phase, transforming it from a coarse to a more desirable fibrous or lamellar structure, thus improving the alloy’s overall performance. The innovative findings underscore the potential of Sr as an effective microstructural modifier for enhancing the durability and longevity of Al-Si alloys in corrosive environments.

Enhancing corrosion resistance of lightweight metal alloys through laser shock peening

In this study, we investigated the effects of laser shock peening (LSP) on the corrosion resistance of lightweight metal alloys, specifically AA6061 and AZ31. LSP was performed underwater, using a nanosecond pulse laser and without using a protective coating or layer on the workpiece. The corrosion behaviors of these alloys were analyzed through electrochemical tests, including open circuit potential, electrochemical impedance spectroscopy, and potentiodynamic polarization measurements. The results demonstrated that LSP significantly improved the polarization resistance, and higher laser power intensities led to increased corrosion resistance and reduced corrosion rates. This enhancement in anti-corrosion performance is attributed to the formation of a protective oxide layer on the surface, acting as a barrier against corrosion. The findings underscore the potential of laser surface treatment as a viable technique for enhancing the corrosion resistance of lightweight metal alloys.

Enhanced Anti-Corrosion and Biological Performance of Plasma-Sprayed Nb/ZrO2/HA Coatings on ZK60 Mg Alloy

Niobium (Nb) and zirconium dioxide (ZrO2) were doped into hydroxyapatite (HA) to fabricate HA-based composite coatings prepared on a ZK60 magnesium alloy by plasma spraying technology to improve anti-corrosion and biocompatibility for clinical applications. The results revealed that the Nb-enriched coating exhibits fewer cracks and pores with a flat surface due to the decreased temperature gradient during spraying, and small needle-like structures can fill the cracks and pores in the ZrO2-contained coating, resulting in a more uniform and dense surface. Compared to coatings with only niobium or zirconium dioxide, the ZrO2/Nb/HA composite coating significantly enhanced the mechanical properties and corrosion resistance of the magnesium alloys. Among all the specimens, the ZrO2/HA coating and ZrO2/Nb/HA coating revealed high surface hardness values (327.73 HV and 293.80 HV, respectively). However, the higher hardness value made the ZrO2/HA coating fragile and more likely to crack, while the ZrO2/Nb/HA coating avoided this shortcoming and exhibited a more comprehensive performance. During immersion tests, the ZrO2/Nb/HA coating exhibited a gradual pH increase and minimal mass loss, and the cytocompatibility test demonstrated promising cellular activity.

Powder bed fusion of solid and permeable Crofer 22 APU parts for applications in chemical process engineering

AbstractAdditive manufacturing of metals has attracted significant attention across various industries. However, its adoption in certain chemical and energy sectors remains constrained by the absence of optimized alloys tailored for high temperatures and corrosive environments. This study explores the laser-based powder bed fusion processing of Crofer 22 APU, a high-temperature, corrosion-resistant alloy ideal for applications such as methane steam reforming reactors, high-temperature fuel cells, and palladium membrane supports. Systematic optimization of laser parameters including laser power, hatch distance, point distance, and building angles was conducted for both dense and porous objects. Dense parts achieved a relative density of 0.9999 and surface roughness of Sa= 41.27±1.48 on a 45$$^\circ$$ ∘ overhang. Porous samples showed a porosity range of 28.655.5% and surface roughness Sa 22.2 $$\upmu$$ μ m to 45.9 $$\upmu$$ μ m as hatch distance increased from 0.12 mm to 0.16 mm. Additionally, an 8YSZ coating applied via screen printing demonstrated the impact of hatch distance and laser power on surface quality. The combination of additive manufacturing of Crofer 22 APU and screen printing of 8YSZ simplifies the preparation of metallic supports for Pd-based membranes, reducing fabrication time and cost by shortening the number of preparation steps. This technique offers a promising approach for scaling up membranes and membrane reactors.

Unveiling the influence of zirconium on the corrosion behavior of Fe-36Ni Invar alloy

The influence of zirconium (Zr) on the corrosion resistance of Fe-36Ni Invar alloy in a 3.5 wt% NaCl solution was systematically investigated. Results indicated that adding Zr promoted the formation of Zr-bearing intermetallic compounds (Ni7Zr2 and Ni2Zr). The phases suppressed the grain growth and numerous dislocations were enriched around the Ni-Zr phases. Unfortunately, the incorporation of Zr into Fe-36Ni Invar alloy impaired corrosion resistance. The marked disparity in Volta potential between the Ni-Zr phases and the matrix signified the existence of micro-galvanic coupling, which caused the matrix to dissolve preferentially. Furthermore, the matrix around the Ni-Zr phases possessed high dislocation density, promoting the emergence of local galvanic corrosion. The introduction of Zr also decreased the protectiveness of the passive film, which was ascribed to the reduction of the thickness of the passive film and the beneficial oxide content in the passive film.

Effect of stage gas nitriding on corrosion and wear resistance of Ti6Al4V alloy in physiological environment

The wear and corrosion resistance of the Ti6Al4V alloy after gas nitriding combined with stage heat treatment was studied in the physiological environment. It was shown that nitriding temperature at the first stage of the heat treatment mainly effects on the surface quality and microhardness of the treated alloy. The corrosion behaviour of the nitrided Ti6Al4V alloy was studied in Ringer's solution, which simulates the physiological environment of human body. It was shown that the corrosion resistance of the alloy is enhanced by increasing thickness and TiN content in the nitride layer, and improving surface quality. The tribological characteristics of the nitrided Ti6Al4V alloy in a tribo-pair with PE-UHMW were evaluated in a 10% aqueous solution of chondroitin sulfate, which simulates the synovial fluid. It was established that reducing nitriding temperature at the first stage of the heat treatment improved the wear resistance of the treated alloy due to decrease of the surface roughness and microhardness.

تأثير استعمال ليزر النيوديميوم ياك (Nd-YAG) على البنية الدقيقة وصلابة سطح الفولاذ AISI1012

The unique characteristics of the laser beam such as directionality, monochromaticity, and brightness make it a very important tool in the surface treatment engineering. The concentrated heat in the laser beam can be precisely directed toward the processed region on the surface. The laser beam power, beam size, and scanning velocity are easily controlled during the different processing methods. Laser surface modifications of metallic materials, such as laser surface melting, laser surface alloying, and laser cladding are some of the most important methods to improve the mechanical properties of the processed layer on the surface. A pulsed Nd-YAG laser surface melted specimens of low carbon steel with a maximum power of 90W at different processing parameters. The rapid melt and solidification of the treated layer produced a refinement in the microstructure. The original microstructure of this steel (Ferrite + Pearlite) has been transformed to new phases of martensitic and bainitic structures. The melted layer consists of the melted pool, the heat affected zone, and the substrate. The maximum hardness of the laser melted layer is more than 400 HV. The effect of different lasers such as high power CW CO2 laser on the mechanical properties and corrosion resistance of steel alloys will be carried out in future studies. Keywords: Nd-Yag Laser, Laser surface treatment, Microstructure and hardness of AISI1012 steel

Enhancing aesthetics, hardness and corrosion resistance of aluminum alloy via deposition of Al/Si/AlN coatings

Enhancing aesthetics, hardness and corrosion resistance of aluminum alloy via deposition of Al/Si/AlN coatings

Construction and biocompatibility evaluation of CS-FA/VA composite coating on the surface of ZE21B vascular stent

Magnesium alloys have become the focus of attention as a new generation of vascular stent materials due to their excellent mechanical properties and degradability. However, their rapid degradation rate and poor surface endothelialization performance have become key factors limiting their clinical application. In this study, the Mg-Zn-Y-Nd (ZE21B) surface was modified with the magnesium fluoride (MgF2) corrosion-resistant layer, and the polydopamine (PDA) layer was used to immobilize the chitosan (CS)-ferulic acid (FA)/vanillic acid (VA) bioactive composite coating. The results of the electrochemical and hydrogen evolution experiments showed that the corrosion current density and hydrogen release of the modified ZE21B alloy significantly decreased, and its corrosion resistance was enhanced; the results of the hemolysis rate and whole blood experiments showed that the adhesion of blood components such as white blood cells and platelets on the surface of the modified ZE21B alloy significantly decreased, improving the blood compatibility of the magnesium alloy; the results of in vitro cell experiments showed that the modified ZE21B alloy effectively promoted endothelial cell (ECs) adhesion and proliferation, and inhibited smooth muscle cell (SMCs) pathological proliferation. These enhancements suggest that the CS-FA/VA coating significantly improves both the corrosion resistance and biological compatibility of the ZE21B alloy.

Microstructure and localized corrosion properties of 2219 aluminum alloy manufactured by additive friction stir deposition

Multi-layer 2219 aluminum alloy samples were successfully fabricated using additive friction stir deposition (AFSD). AFSD deposition reduced grain size and the size of intermetallic Al2Cu particles, but greatly increased the amount of Al2Cu particles. More Al2Cu particles increased the number of galvanic microcells on alloy surface and at the grain boundaries, which promoted the localized corrosion and improved the intergranular corrosion sensitivity of AFSD alloy. Subsequent T6 heat treatment had little effect on grain size but enhanced the corrosion resistance of AFSD alloy, primarily attributed to the reduction in Al2Cu particles and the elimination of dislocations within grains.

Enhanced wear resistance, corrosion behavior, and thermal management in magnesium alloys with PEO coatings

The harsh conditions encountered in aerospace applications, such as high operational temperatures, abrasive wear, and corrosive substances, present significant challenges to the performance and longevity of magnesium alloy components. To create a coating with superior wear resistance, corrosion resistance, and high emissivity, this study employs plasma electrolytic oxidation (PEO) technology to develop a nanocomposite coating doped with carbon nanotubes (CNTs) and hexagonal boron nitride (h-BN). The results demonstrate that the MgO-BN/CNTs coating with an emissivity of 0.82 reduces the equilibrium temperature of the 5 W LED junction by nearly 10 °C compared to the magnesium alloy substrate, showing improved radiative heat dissipation performance. Due to the ability of the porous structure to accommodate abrasive particles, coupled with the lubricating effect of h-BN and CNTs, the friction coefficient of the MgO-BN/CNTs coating is 0.57, which is 21 % lower than that of the MgO coating. Additionally, the coating exhibits excellent corrosion protection, attributed to the dense microstructure and chemical inertness of h-BN. The findings demonstrate that the strategic incorporation of h-BN and CNTs into PEO coatings effectively improves the wear resistance, corrosion resistance, and thermal management performance of magnesium alloys.

Influences of friction stir processing on the microstructure and properties of TC4 titanium alloy by laser metal deposition

To enhance the properties of TC4 titanium alloy samples prepared by Laser Metal Deposition (LMD), while minimizing metallurgical defects and increasing relative density of the samples, the advanced Friction Stir Processing (FSP) technology was employed to conduct a refined secondary modification on the LMD-deposited TC4 titanium alloy samples. The comprehensive influences of FSP on the microstructure and properties of the as-deposited TC4 titanium alloy were emphatically investigated. The results reveal that the as-deposited TC4 titanium alloy exhibits a microstructure characterized primarily by columnar grains interspersed with a minor amount of equiaxed grains in the vertical section. After FSP treatment, the microstructure transforms into a new morphology where more refined equiaxed grains coexist with bimodal structures. Meanwhile, on the horizontal plane, the existing equiaxed grains are further refined, and the microstructure gradually transitions from the original Widmanstätten and basketweave structures to a more uniform laminar structure. Accordingly, the transformation of the microstructure leads to enhanced mechanical properties of the TC4 titanium alloy. Compared to the untreated as-deposited titanium alloy, the hardness of the FSP-processed samples significantly increases by 46.9 HV1 on the horizontal plane and 33.8 HV1 on the vertical plane. Additionally, the reduction in friction coefficient (from 0.47 to 0.41), a substantial decrease in wear mass (3.7 mg), and a slight improvement in the corrosion resistance of the titanium alloy collectively demonstrate the effectiveness of the FSP process in enhancing the performance of as-deposited TC4 titanium alloy.

Effects of Mo Addition on Microstructure and Corrosion Resistance of Cr25-xCo25Ni25Fe25Mox High-Entropy Alloys via Directed Energy Deposition

Effects of Mo Addition on Microstructure and Corrosion Resistance of Cr25-xCo25Ni25Fe25Mox High-Entropy Alloys via Directed Energy Deposition

Use of Pulsed Potentials for Electropolishing TA6V Parts Elaborated By Additive Manufacturing in Deep Eutectic Solvent

The Ti-6Al-4V alloy's high mechanical properties, low density, excellent biocompatibility, and corrosion resistance make it an ideal material for sectors such as aeronautics, astronautics and medical technology. The demand for increasingly complex part designs is speeding up the development of Additive Manufacturing (AM) technology, enabling the creation of shapes unachievable with traditional machining. However, the parts manufactured present significant surface roughness, thus reducing resistance to corrosion and mechanical stress. To mitigate these risks, homogeneous polishing of the entire shape is required. Electrochemical polishing is an all-round part treatment technique ideal for addressing AM challenges. Deep Eutectic Solvent (DES) electrolytes are well-suited for this application. The aim of this study is to develop electropolishing of Ti-6Al-4V parts in a DES solvent of ethylene glycol and choline chloride. The challenges posed by viscous layer thickness problems, as well as two methods to overcome them, are described, including agitation control and pulsed potentials.

State-of-the-Art titanium carbide hard coatings: a comprehensive review of mechanical and tribological behaviour

Abstract This present paper focuses on various conventional and advanced surface modification techniques to enhance surface characteristics, tribological behaviour, and mechanical properties of metals and alloys exposed to abrasive or corrosive environments. A particular emphasis is placed on the utilization of hard protective coatings, notably Titanium Carbide (TiC), known for its exceptional attributes including high chemical and thermal stability, elevated hardness, substantial elastic modulus and a low coefficient of friction. TiC coatings significantly contributes to the enhanced hardness, wear and corrosion resistance of metals and alloys. Deposition of TiC coatings using various technologies including chemical vapor deposition (CVD), physical vapour deposition (PVD) and laser-based approaches finds application in automobile manufacturing, cutting tools, marine environments, aerospace components, machinery parts among others. In this context the discussion intricately analyses the impact of processing parameters on the wear and hardness of TiC coatings along with characterization techniques employed for testing microstructure and tribological properties. A comparative study of various deposition methods is meticulously presented, offering insights into the strengths and limitations of each approach.

Effects of Ti and Y on resistance to corrosion in Fe–Cr-X Alloys

The effect of Ti and Y on the corrosion behavior of the FeCr alloy was investigated in a 3.5% NaCl solution. Ti was found to inhibit the formation of the σ phase, significantly reducing the presence of pitting in the material. In addition, Ti acted indirectly on the oxide layer, increasing the concentrations of Cr and Fe, consequently generating a probable enrichment of Cr2O3 and FeOOH, which enabled the formation of a more stable passive film resistant to attack by chloride ions. On the other hand, Y caused the precipitation of a phase identified as Fe17Y2, which was accompanied by an elongated σ phase, both located at the grain boundaries, besides the formation of Cr23C6 and Y2O3. Its addition resulted in an improvement in the corrosion resistance of the FeCr alloy by reducing the precipitation of the σ phase. However, its effect was much less important than that of Ti, since the results showed that the FeCrY alloy was still highly susceptible to localized forms of corrosion.

Investigation of Mechanical and Corrosion Properties of New Mg-Zn-Ga Amorphous Alloys for Biomedical Applications.

Magnesium alloys are considered as promising materials for use as biodegradable implants due to their biocompatibility and similarity to human bone properties. However, their high corrosion rate in bodily fluids limits their use. To address this issue, amorphization can be used to inhibit microgalvanic corrosion and increase corrosion resistance. The Mg-Zn-Ga metallic glass system was investigated in this study, which shows potential for improving the corrosion resistance of magnesium alloys for biodegradable implants. According to clinical tests, it has been demonstrated that Ga ions are effective in the regeneration of bone tissue. The microstructure, phase composition, and phase transition temperatures of sixteen Mg-Zn-Ga alloys were analyzed. In addition, a liquidus projection of the Mg-Zn-Ga system was constructed and validated through the thermodynamic calculations based on the CALPHAD-type database. Furthermore, amorphous ribbons were prepared by rapid solidification of the melt for prospective alloys. XRD and DSC analysis indicate that the alloys with the most potential possess an amorphous structure. The ribbons exhibit an ultimate tensile strength of up to 524 MPa and a low corrosion rate of 0.1-0.3 mm/year in Hanks' solution. Therefore, it appears that Mg-Zn-Ga metallic glass alloys could be suitable for biodegradable applications.

Enhancing the mechanical properties and corrosion resistance of biomedical Ti15Mo alloy with ultra-finer {332} twins via cyclic deformation

Mechanical properties, passivation behaviors and corrosion resistance of biomedical Ti15Mo alloy with ultra-finer twins were investigated. Cyclic deformation was conducted to activating more {332} twin variants via periodic changes of tension and compression. Microstructural refinement via numerous twins with the stable boundaries is different from other mechanisms, resulting in a higher hardness and maintaining the low elastic modulus after deformation and annealing. The results of electrochemical impedance spectroscopy and X-ray photoelectron spectroscopy tests, revealed that twin boundaries are beneficial to enhancing passivation behaviors via forming a thicker oxide film in PBS solution. The alloy with ultra-finer {332} twins exhibit a better corrosion resistance due to a lower passivation current. The expected biomedical performance was obtained in the alloy after ±3 % amplitude cyclic deformation and 730 °C/7 min annealing, in contrast to the initial alloy with coarse grains, increasing 8.8 % of the hardness, decreasing 46 % of the corrosion current and maintaining the low elastic modulus.

Investigation on corrosion behaviour of metal oxide nanoparticles reinforced magnesium composites by salt spray and immersion corrosion test methods

ABSTRACT This study explores the increasing utilisation of lightweight materials, particularly magnesium (Mg) alloy, in sectors such as automobile, aerospace, and marine due to its notable advantages such as high strength-to-weight ratio, good castability, and excellent damping capacity. Despite these merits, Mg alloy faces challenges, notably in wear and corrosion resistance. The research focuses on enhancing the corrosion resistance of Mg alloy by incorporating Zinc Oxide (ZnO), Manganese Oxide (MnO), and Titanium Oxide (TiO2) nanoparticles. The alloy AZ91D and three nanocomposites, namely AZ91D + 1% ZnO, AZ91D + 1% MnO, and AZ91D + 1% TiO2, were manufactured using a stir squeeze casting technique combined with an ultrasonication process. To confirm the even distribution of reinforcement particles, Optical Microscope (OM), Scanning Electron Microscope (SEM) and High-Resolution Scanning Electron Microscope (HR-SEM) were employed. X-ray Diffraction (XRD) analysis revealed the presence of matrix and reinforcement material with intermetallic precipitates around the grain boundaries. Corrosion properties were assessed following ASTM standards and utilising a 3.5% NaCl concentration. The study found that AZ91D + 1% TiO2 nanocomposites exhibited superior corrosion resistance compared to the AZ91D alloy, showing a remarkable 77.78% and 69.89% improvement in corrosion behaviour under salt spray and immersion environments, respectively, after 48 hours.