Conversion Efficiency Of Cells Research Articles

Regulation of Lead Iodide Crystallization and Distribution for Efficient Perovskite Solar Cells.

At present, the power conversion efficiency (PCE) of perovskite solar cells (PSCs) has reached 26.1%. Polycrystalline perovskite films prepared by sequential deposition are often accompanied by excess PbI2. Although excess PbI2 can reduce the internal defects of the perovskites and promote charge transfer, excess PbI2 is unevenly distributed in the perovskites and easily decomposed into the composite center of charge. Therefore, the growth and distribution of PbI2 crystals can be regulated by introducing 4-fluoroaniline (4-FLA) as an additive into the precursor of PbI2. We observe that the presence of an amino group in 4-FLA leads to a reduction in the strength of van der Waals forces between PbI2 layer structures, thereby facilitating the uniform dispersion of excess PbI2 within the perovskites. Additionally, 4-FLA is restricted from being embedded in the PbI2 layer due to the steric hindrance of 4-FLA and the hydrogen bond interaction between nitrogen atoms and PbI2. Therefore, it leads to better dispersion of PbI2, resulting in better passivation and device efficiency. Based on the hydrophobicity of the benzene ring, the modified perovskite film shows excellent hydrophobicity. Ultimately, we achieved 21.63% PCE and 1.16V VOC. This provides an effective strategy for regulating excess PbI2 to achieve efficient and stable PSCs.

Amphipathic Astaxanthin Additive for Low Voltage-loss Perovskite Solar Cells With Enhanced Quasi-Fermi Level Splitting and Solar Hydrogen Production Application.

Even though the power conversion efficiency (PCE) of perovskite solar cells (PSCs) is nearly approaching the Schottky-Queisser limit, low open-circuit voltage (Voc) and severe Voc loss problems continue to impede the improvement of PCEs. Astaxanthin (ASTA) additive is introduced in the formamidinium lead triiodide (FAPbI3)perovskite film as an additive, which can facilitate the transportation of charge carriers and interact with Pb2+ by its distinctive groupings. Furthermore, the addition of ASTA decreases the defect's active energy, regulates the deep-level defect by filling up the grain boundaries (GBs), and promotes the crystallization of perovskite film. Remarkably, an enhanced quasi-Fermi level splitting (QFLS) of 1.164eV and a reduced Voc loss of only 96mV are realized. The champion PCE of 24.56% is attained by ASTA-modified PSCs on the basis of 22.75% PCE. Moreover, the PSCs that underwent ASTA modification demonstrate improved operational stability, ensuring consistent output in real-world scenarios. Furthermore, PSCs with an active area of 1 cm2 are used for water electrolysis to produce hydrogen and exhibit a PCE of 22.41%. This work offers an environmentally benign solution to address the inherent issues of FAPbI3 PSCs and lays the groundwork for the development of a prospective solar hydrogen production application.

PhDMADBr assisted additive or interface engineering for efficient and stable perovskite solar cells fabricated in ambient air

The fabrication of high-quality perovskite films with low defect density in ambient air is an important approach to enhance the power conversion efficiency (PCE) and stability of perovskite solar cells (PSCs). In this paper, efficient and stable PSCs were fabricated in ambient air, and p-xylilenediamine bromide (PhDMADBr) assisted additive or interface engineering were carried out to modify perovskite films, which was dispersed into the electron transport layer (ETL) or deposited in the ETL/ perovskite interface. Notably, interaction between PhDMADBr and perovskite layer could reduce defect density and release residual stress of the active layer, which would induce a high-quality perovskite film, and accelerate the transport rate and prolong lifetimes of charge carriers, contributing to the PCE and stability of devices. As a result, compared with the PCE of the control device (22.54 %), the PhDMADBr modified target PSCs exhibited the enhanced PCE of 24.15 % and 23.74 % after additive or interface treatments in ambient air, respectively. Except the improvement of the PCE, PhDMADBr-based devices also presented the enhanced moisture stability. The average efficiency retained the 88 % or 84 % of initial efficiency after 120 h with RH of 40 ± 5 % for additive or interface modification, respectively. In contrast, the PCE of the control devices would decline to 51 % of initial efficiency after storage for 120 h.

UV-OZONE Treatment for Suppressing Surface Damages on Silicon Solar Cells.

In the preparation process of c-Si solar cells, qualified Si wafers must be processed through mechanical processing during manufacturing. Most of these processes involve mechanical processing, which inevitably results in severe mechanical damage layers and a wafer surface with large roughness. The current industry practice involves etching of the damage layer using an acid/alkali solution, and it is usually followed by deposition of additional passivation layers in the subsequent processes. However, even with these treatments, there still remain non-negligible microscopic saw damage and scratches on the wafer surface, which hinder the urgent development of a higher conversion efficiency of solar cells. Here, we provide a simple method to effectively suppress the impact of this surface damage. UV-OZONE treatment, which involves generation of an oxide layer and subsequent cleaning with hydrofluoric acid, leads to the effective regain of solar cell performance due to the passivation of dangling bonds and removal of sharp microstructures based on the creation of mechanical scratches. In addition, PEDOT:PSS/n-Si solar cells were prepared to exploit their strong surface dependence to investigate the effect of scratches on the overall performance. These results further validate the impact of scratches on solar cells, and a simple and effective method for surface damage suppression is provided.

Doubling Power Conversion Efficiency of Si Solar Cells.

Improving solar cells' power conversion efficiency (PCE) is crucial to further the deployment of renewable electricity. In addition, solar cells cannot function at exceedingly low temperatures owing to the carrier freeze-out phenomenon. This report demonstrates that through temperature regulation, the PCE of monocrystalline single-junction silicon solar cells can be doubled to 50-60% under monochromatic lasers and the full spectrum of AM 1.5 light at low temperatures of 30-50 K by inhibiting the lattice atoms' thermal oscillations for suppressing thermal loss, an inherent feature of monocrystalline Si cells. Moreover, the light penetration, determined by its wavelength, plays a critical role in alleviating the carrier freeze-out effect and broadening the operational temperature range of silicon cells to temperatures as low as 10 K. Understanding these new observations opens tremendous opportunities for designing solar cells with even higher PCE to provide efficient and powerful energy sources for cryogenic devices and outer and deep space explorations.

Small molecule induced interfacial defect healing to construct inverted perovskite solar cells with high fill factor and stability

Chemical defects at the surface and grain boundaries of perovskite crystals cause deterioration of conversion efficiency and stability of perovskite solar cells (PSCs). In this study, a multifunctional additive, 5-fluoro-2-pyrimidine carbonitrile (FPDCN) molecule, is added into the perovskite precursor solution in order to passivate the uncoordinated Pb2+ by the cyanogen (–CN) group and pyrimidine N in FPDCN. Interestingly, fluorine (F) atoms interact with FA+ to form hydrogen bonds, which could regulate the perovskite crystallization process for the formation of high-quality perovskite crystals. Besides, the F atoms in FPDCN increase the water contact angle of perovskite films. As a result, the carrier extraction and transport in the perovskite film are significantly enhanced, and the non-radiative recombination is suppressed. The corresponding devices achieve a champion photovoltaic conversion efficiency (PCE) of 20.7 % and a fill factor (FF) of over 83 %. The device based on FPDCN shows long-term stability under a high-humidity atmospheric environment by maintaining 85 % of the initial efficiency after aging of 700 h in the glove box. This study provides a simple and convenient method to prepare stable and efficient PSCs by optimizing the perovskite precursor solution.

Modifying back contact by silver to Enhance the performance of carbon-based Sb2S3 solar cells

Antimony sulfide (Sb2S3) has drawn significant attention due to its excellent photoelectric properties. However, the photon conversion efficiency of Sb2S3 solar cell is limited by its magnificent value band offset between absorber layer and carbon electrode. Herein, a back surface optimization strategy is developed to reduce the barrier at the back contact. By introducing Ag at back contact before post-selenization process, the Valence-Band Maximum (VBM) of Sb2S3 is elevated under the action of spin–orbit interaction between Sb-5 s orbit and Ag-d orbit, leading to improve the extraction of holes. Consequently, the electrical conductivity of the film undergoes a significant improvement, rising from 1.20 × 10-5 to 1.59 × 10-5 S/cm. Additionally, the film surface morphology is refined, exhibiting a reduction in roughness from 17.1 nm to 13.6 nm, which leads to less leak current generated. Finally, the device based on FTO/SnO2/CdS/Sb2S3/Carbon structure achieved the power conversion efficiency (PCE) of 5.51 %, representing a 16 % improvement compared to the device without Ag treatment.

An improved supply of anthocyanin dye for creation of effective dye-sensitized solar cells grounded on natural dyes

Abstract In order to advance the power conversion efficiency of dye-sensitized solar cells, this article shows the selection of better sources of the sensitizer anthocyanin. The cells were created by combining liquid and solid electrolytes, adding natural dye, and employing a photo anode of aluminium-doped zinc oxide and a counter electrode of fluorine-doped tin oxide. Light harvesting efficiency, scanning electron microscopy, ultraviolet and infrared spectroscopy, and other methods were used to characterise the cells. From all the combinations made utilising different sources, the cell based on the D1 dye sample from Hibiscus sabdariffa L. (Manipur) had the best efficiency at 1.58 %. An effective DSSC was the end result of this strategy for identifying the optimal extraction source for anthocyanin natural dyes.

Numerical simulation of all inorganic CsPbIBr2 perovskite solar cells with diverse charge transport layers using DFT and SCAPS-1D frameworks

All inorganic CsPbX3 perovskites (X = Br and I) are excellent candidates for stable and efficient perovskite solar cells (PSCs). Among them, CsPbIBr2 demonstrated the most balanced characteristics in terms of band gap and stability. Nevertheless, the power conversion efficiency (PCE) of CsPbIBr2-based solar cells is still far from that of Hybrid PSCs, and more research is required in this aspect. Herein, DFT and SCAPS-1D frameworks are employed to explore the optimized device configurations of CsPbIBr2 PSCs. DFT is used to explore the structural and optoelectronic characteristics of CsPbIBr2, while SCAPS-1D is employed to examine various device structures of CsPbIBr2-based PSCs. The band structure demonstrated the direct band gap nature of CsPbIBr2 with a band gap of 2.12 eV. Moreover, we have used TiO2, SnO2, ZnO, WS2, IGZO, CeO2, In2S3, and CdS as ETLs, and Cu2O, CuI, MoO3, NiO, CuSCN, CuSbS2, CBTS, CFTS, and CuO as HTLs for identifying the best ETL/CsPbIBr2/HTL configurations. Among 72 device combinations, eight sets of PSCs are identified as the most efficient configurations. In addition, the influence of various parameters like the thickness of various layers, doping concentration, perovskite defect density, ETLs and interfaces, series resistances, shunt resistances, and temperature on device performance have been comprehensively studied. The results demonstrate Cu2O as the best HTL for CsPbIBr2 with each ETL, and PSC with device structure ITO/WS2/CsPbIBr2/Cu2O/C exhibited the highest PCE of 16.53%. This comprehensive investigation will provide new path for the development of highly efficient all-inorganic CsPbIBr2 solar cells.

A comparative spin orbit coupling DFT study of opto-electronic properties of [formula omitted] and [formula omitted] bulk crystal

Bi2Se3 and Bi2Te3 are the ideal candidate for spintronics and many other novel applications due to their strong opto-electronic properties. These materials are regarded as topological insulator as they portray band inversion which is considered to be a key signature of topology. Moreover, because of their superior opto-electronic qualities, Bi2Se3 and Bi2Te3 are intriguing in the realm of optical and electronic applications. This paper compares the optical and electronic characteristics of Bi2Te3 and Bi2Se3 in the framework of density functional theory taking PBE-GGA and mBJ-GGA as exchange correlation potential. The analysis of band structure and density of states (DOS) confirms the gapped nature without and with SOC calculation. The introduction of SOC gives the accurate result which matches with the experimental figure. Optical properties including reflectivity, absorption coefficient, energy loss function, refractive index, extinction coefficient, and optical conductivity are analyzed without and with SOC. We have also calculated birefringence, dichroism, and the optical skin depth which has not been reported yet for those compounds. The spectroscopic limited maximum efficiency (SLME), which theoretically determines the power conversion efficiency (PCE) of solar cells is also calculated. Based on the optical and electronic properties, possible uses of Bi2Se3 and Bi2Te3 are discussed without and with SOC effect.

Ultrafast hole transfer mediated by a conjugated self-assembled molecule enables efficient and stable wide-bandgap perovskite solar cells

Charge accumulations and electron recombination at the interfaces between perovskites and charge transporting materials are two critical factors significantly hindering the power conversion efficiency (PCE) and device stability of wide-bandgap perovskite solar cells (WBG PSCs). Herein, we tailor-made a self-assembled molecule (SAM), termed XS13, featuring an enlarged π-donor and a π-linker, to regulate the interface carrier dynamics in ∼1.8 eV WBG PSCs. Ultrafast spectroscopy clearly demonstrated that the XS13 facilitated the rapid extraction and transfer of photo-generated holes compared to the reference SAM-2PACz. Consequently, WBG PSCs based on XS13 achieved an outstanding PCE of up to 19.20 %, surpassing that of control devices (16.41 %). Furthermore, XS13-based WBG PSCs exhibited a remarkable suppression of light/electricity-induced halide ions migration, leading to significantly improved device stability. Our findings offer a new strategy for the rational design of hole transporting molecules with controlled properties to enhance device performance of PSCs.

Ternary Passivation for Enhanced Carrier Transport and Recombination Suppression in Highly Efficient Sn-Based Perovskite Solar Cells.

The exploration of nontoxic Sn-based perovskites as a viable alternative to their toxic Pb-based counterparts has garnered increased attention. However, the power conversion efficiency of Sn-based perovskite solar cells lags significantly behind their Pb-based counterparts. This study presents a ternary passivation strategy aimed at enhancing device performance, employing [6,6]-phenyl-C61-butyric-acid-methyl-ester (PCBM), poly(3-hexylthiophene) (P3HT), and indene C60 bisadduct (ICBA). These components play crucial roles in managing energy levels and enhancing carrier transportation, respectively. The results reveal that the introduction of the ternary system leads to improvements in carrier collection and transportation, accompanied by a suppression of the recombination process. Ultimately, the champion device achieves a remarkable performance with an efficiency of 14.64%. Notably, the device also exhibits robust operational and long-term stored stability.

Fabrication of Nano-Carbon-Based Sustainable Perovskite Solar Cells

The rising need for sustainable energy solutions has fuelled considerable research into novel technologies that harness solar energy for efficient and scalable energy storage. Carbon nanotubes (CNTs) have emerged as feasible candidates for these applications due to their unique properties, such as high surface area, better electrical conductivity, and chemical stability.This report focuses on the design and fabrication of cost-effective nano-carbon-based perovskite solar cells (PSCs) and discusses their potential for clean energy generation and storage. This experimental study shows a novel technique to increase the sustainability the conventional fluorine-doped tin oxide (FTO) substrate with an Indium Tin Oxide (ITO) derived from electronic waste and incorporating nanocarbon based-graphene with solution-based techniques. This addition serves as a good basis for the ITO coating, aids charge transport in the perovskite solar cell, and promotes uniform covering maximum electrical conductivity, and transparency. Being the transparent conducting electrode, the CNTs is infused with the upcycled ITO coated glass and was included in the perovskite solar cell architecture, which replaces the traditional ITO electrode, lowering material costs, and improving the circular economy for energy storage devices, and a cleaner energy future.The ITO extraction process entails recovering indium and tin from mobile phones using an environmentally friendly and economical chemical etching process using hydrochloric acid (HCl) to remove the ITO layer. To ensure the purity and structural integrity of the ITO nanoparticles, they were rigorously characterized using X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. After depositing a perovskite- CNTs precursor solution on the ITO layer glass substrate, the light-absorbing layer was annealed. Electron transport and hole-blocking layers were then deposited utilizing solution processing techniques using the PEDOT: PSS and metal electrodes were deposited to complete the device manufacturing. The current-voltage (J-V) relationship was used to compute the open-circuit voltage, short-circuit current density, fill factor (FF), and power conversion efficiency (PCE) of a solar cell. Electrical characterization allow for the calculation of solar cell performance metrics such as short-circuit current (Isc), short-circuit current density (Jsc), and open-circuit voltage (Voc). These findings imply that employing e-waste-derived ITO on graphene substrates to create high-efficiency perovskite solar cells is a realistic option. This research provides a sustainable and cost-effective method for producing high-performance perovskite solar cells by eco-friendly upcycling e-waste for ITO extraction, addressing the critical issue of e-trash management. Keywords Perovskite solar cells, CNTs, sustainable energy, energy conversion.

Utilization of Polycyclic Aromatic Solid Additives for Morphology and Thermal Stability Enhancement in Photoactive Layers of Organic Solar Cells.

Volatile solid additives have emerged as a promising strategy for enhancing film morphology and promoting the power conversion efficiency (PCE) of organic solar cells (OSCs). Herein, a series of novel polycyclic aromatic additives with analogous chemical structures, including fluorene (FL), dibenzothiophene (DBT), and dibenzofuran (DBF) derived from crude oils, are presented and incorporated into OSCs. All these additives exhibit strong interactions with the electron-deficient terminal groups of L8-BO within thebulk-heterojunction OSCs. Moreover, they demonstrate significant sublimation during thermal annealing, leading to increase free volumes for the rearrangement and recrystallization of L8-BO. This phenomenon leads to an improved film morphology and an elevated glass-transition temperature of the photoactive layers. Consequently, the PCE of the PM6:L8-BO blend has been boosted from 16.60% to 18.60% with 40 wt% DBF additives, with a champion PCE of 19.11% achieved for ternary PM6:L8-BO:BTP-eC9 OSCs. Furthermore, the prolonged shelf and thermal stability have been observed in OSCs with these additives. This study emphasizes the synergic effect of volatile solid additives on the performance and thermal stability of OSCs, highlighting their potential for advancing the field of photovoltaics.

The selenium substitution of solvent additive enables efficient polymer solar cells with efficiency of 19.4 %

Solvent additives, which are widely used as versatile tools for refining active layer morphology, have been considered as important role in enhancing the power conversion efficiency (PCE) of polymer solar cells (PSCs). Herein, innovative solvent additive 2,5-dibromoselenophene (BrS), is devised and synthesized by substituting the sulfur atom in 2,5-dibromothiophene (BrT) with selenium atom. The facile polarization properties of selenium atoms enable selenophene to participate in intermolecular interactions with oxygen or sulfur atoms. Therefore, incorporating BrS into the blend solution leads to refined intermolecular interactions and molecular packing, and crystallinity, resulting in a refined bulk heterojunction (BHJ) morphology compared to using the solvent additives 1-chloronaphthalene (CN) and BrT. Consequently, the BrS outperform their BrT and CN in improving photon absorption, exciton dissociation, and charge collection properties of PSCs, yielding an enhanced PCE of 18.0 % in PM6:Y6 BHJ devices. Moreover, the BrS solvent additive exhibit general applicability in both non-fullerene small molecules PSCs and all-polymer PSCs. High efficiency of 18.8 %, 19.4 % and 18.1 % are obtained in PM6:L8-BO, D18:L8-BO, and PM6:PY-IT BHJ solar cells, respectively, which is rankable among the paramount performance reported to date. Our results highlight the potential of selenophene-based solvent additives as an observable pathway for nanomorphology of active layer and effective enhancement of PCE in PSCs.

Lithium-based water-absorbent hydrogel with a high solar cell cooling flux

The lifetime and photovoltaic conversion efficiency of the solar cell will decline as the temperature rises. Herein, a versatile hydrogel allowing atmospheric water harvesting and evaporative cooling is introduced to passively reduce the working temperature of the solar cell. As a flexible substrate, the lithium-rich and highly absorbent polyacrylamide hydrogel is employed to satisfy these specifications. Preferentially, the water-saturated hydrogel, which is bonded to the backside of the solar cell, collects the waste heat produced by the cell and dissipates it into the atmosphere by water evaporation. Importantly, the hydrogel naturally gathers atmospheric vapor at night or on overcast days to revive its cooling ability. This configuration endows the PV cell with a cooling flux of up to 529 W m–2 and thus reduces the working temperature of a polycrystalline silicon cell by 26 °C at 1 sun (=1 kW m–2) illumination. More importantly, the hydrogel arrangement supports 6.2% and 17% improvements in average open-circuit and maximum power output, respectively. This is devoid of limits on access to liquid water resources, making it a potential option for efficient and sustainable solar cell power generation.

Enhancing power conversion efficiency of polycrystalline silicon photovoltaic cells using yttrium oxide anti-reflective coating via electro-spraying method

The achievement of optimal performance is a crucial aspect of renewable energy resources. The study attempts to boost the power conversion efficiency of polycrystalline silicon (Si) photovoltaic cells by the application of anti-reflective coating (ARC). The solgel method is employed to synthesize yttrium oxide (Y2O3). The electro spraying method was utilized to apply the ARC on photovoltaic cells. The effect of coating on PV cells were determined through the structural, electrical, optical and thermal analysis. The antireflective material was uniformly applied over the coated substrate for 45 min (Y-I), 90 min (Y-II), 135 min (Y-III), and 180 min (Y-IV). The sample coated for 135 min showed an optimal power conversion efficiency (PCE) of 21.65 % and 20.09 % in the presence of neodymium light and direct sunlight, respectively, and a minimum electrical resistivity of 3.96 × 10−3 Ω-cm. In addition, Y-III coated cells exhibit a maximum absorbance of 94 %. The Y-III coated photovoltaic cells demonstrated the lowest temperature of 34.6 °C when exposed to an open environment and 40.6 °C when exposed to a controlled environment. The results from numerous studies demonstrated that Y2O3 can be a suitable ARC, which effectively improved the efficiency of photovoltaic cells.

Interfacial Bridging Enables High Performance Perovskite Solar Cells with Fill Factor Over 85%

AbstractThe power conversion efficiency (PCE) of perovskite solar cells (PSCs) is approaching their Shockley‐Queisser (S‐Q) limit through numerous efforts in key parameters improvement. To further approaching the limit, it is important to facilitate the fill factor (FF), a parameter closely related to carrier transport and nonradiative recombination. Herein, an interfacial bridging strategy is proposed to improve FF, which utilizes functional graphene quantum dots at the tin oxide (SnO2)/perovskite buried interface. As a result, synergistic effects of enhanced conductivity of SnO2, preferable energy alignment at the buried interface and improved perovskite crystal orientation are realized. The champion FF reaches 85.24% in formamidinium lead iodide (FAPbI3) based PSCs, which ranks among the highest in the n‐i‐p structure. Such strategy is also proven successful in other perovskite systems, where the champion PCE reaches 24.86% in the formamidinium‐cesium (FACs)‐based devices and 24.44% in the flexible devices. Therefore, this work provides a practical design rule for pursuing high FF of PSCs with carbon materials.

Study on the Key Parameters Affecting the Power Conversion Efficiency of Cs2AgBiBr6-Based Perovskite Solar Cells

The lead-free halide double perovskite material A2BB’X6 represented by Cs2AgBiBr6, has higher potential as a photovoltaic material since it has good electronic and optical properties in recent years. However, the highest power conversion efficiency (PCE) achieved for solar cells made with Cs2AgBiBr6 as the light-absorbing layer in experiments is only 2.51%. To investigate this phenomenon, we used the Solar Cell Capacitance Simulator (SCAPS) simulation software to build five solar cell models with the structure of FTO/ZnO/Light-absorbing layer/Cu2O/Au based on different light-absorption layer materials. Two reasons causing the low PCE of Cs2AgBiBr6 solar cells were identified. On the one hand, interlayer defects in Cs2AgBiBr6 film synthesis significantly decreased the fill factor (FF), thereby reducing the quantum efficiency (QE). On the other hand, Cs2AgBiBr6’s larger indirect bandgap resulted in a narrower absorption range. Additionally, it was demonstrated that adjusting the material thickness and alloying method could, respectively, improve the two aforementioned issues. When the thickness of the light-absorbing layer material was 300[Formula: see text]nm, the FF increased from 39.88% to 55.01%, resulting in an optimal PCE of 3.88% for the solar cell. Alloying increased the short-circuit current ([Formula: see text]) from 8.44[Formula: see text]mA/cm2 to 21.24[Formula: see text]mA/cm2, leading to a simulated PCE increase of 8.92% for solar cells based on Cs2NaSb[Formula: see text]In[Formula: see text]I6. This work, from the perspective of device simulation, is highly significant for improving the photoelectric conversion efficiency of Cs2AgBiBr6-based perovskite solar cells in experimental settings. It offers new insights for optimizing solar cell efficiency.

Fabricating Cu2Zn(SnxGe1-x)Se4 thin-film solar cells with back surface Ge grading by magnetron sputtering

In this paper, an approach of forming a band gap gradient by depositing a layer of Ge between the Mo layers by magnetron sputtering is proposed. The diffusion depth of the Ge into Cu2ZnSnSe4 (CZTSe) thin film can be effectively controlled by the Mo transition layer, resulting in the formation of Cu2Zn(SnxGe1-x)Se4 (CZTGSe) thin film with a band gap grading along the back surface. To validate the formation of the Ge gradient in the absorber, energy dispersive spectrometer line scanning and grazing incidence X-ray diffraction were performed. Furthermore, the impact of Ge layer on the morphologies of CZTSe was assessed using scanning electron microscopy. As a result, the introduced Ge layer formed a Ge grading along the back surface and improved the crystal quality of the absorber. Compared to CZTSe solar cells, the power conversion efficiency (PCE) of CZTGSe solar cells with a Ge gradient improved from 5.79 % to 9.28 %.