Conventional Strip Research Articles

An optimization of sinusoidal rumble strip design parameters

Previous research has shown that rumble strips using a sinusoidal profile can reduce pass-by noise while creating equal or greater interior noise and vibration compared to more conventional discrete strips. Several different sinusoidal designs have been proposed and evaluated in previous research, however, a single design has yet to be confirmed. In the current research, 20 different sinusoidal designs were installed on a two-lane highway each with different parameters of wavelength, peak-to-peak amplitude, and recess below the existing pavement. The test matrix included wavelengths varying from 30.5 to 60.9 centimeters, peak-to-peak amplitudes from 7.9 to 12.7 millimeters, and recesses of 0 and 3.8 millimeters. Previous research has also shown that the performance of individual designs depends on the individual vehicles used in the testing. In this research, four vehicles of from each of four different design types were used and averaged together to judge the performance of the 20 rumble strip designs for pass-by noise, and interior noise and vibration. From this research, the recommended design is one with a 38.1 centimeters wavelength +/- 12.7 millimeters, no recess, and a peak-to-peak amplitude of 11.1 to 12.7 millimeters. The results used to justify this recommendation are presented in this paper.

Soil profile distribution of organic, inorganic, and labile carbon and nitrogen fractions vary in semi‐arid drylands under long‐term conservation tillage systems

AbstractChanges in soil carbon (C) and nutrients considerably influence soil health and agricultural sustainability. However, how agricultural management affects C and N allocation among various soil organic matter pools and their linkages with soil health are not clear for arid and semi‐arid regions. This study aimed to evaluate the soil profile distribution of selected C and N fractions and associated soil health properties in conventional tillage (CT), no‐tillage (NT), and strip tillage (ST) fields and quantify the relationship of labile and inorganic C and N fractions to soil organic carbon (SOC) sequestration in semi‐arid dryland cropping systems. Crop rotation was a 4‐year cycle of corn (Zea mays L.)—sorghum (Sorghum bicolor L. Moench)—winter wheat (Triticum aestivum L.)—fallow across all tillage systems. Soil samples were collected from 0–20, 20–40, and 40–60 cm depths of each plot in July 2022, after 9 years of plot establishment, and analysed for potentially mineralizable carbon (PMC), microbial biomass carbon (MBC), SOC, soil inorganic (SIC), soil total carbon (STC), soil inorganic nitrogen (SIN), total labile nitrogen (TLN), total organic nitrogen (SON), and labile organic nitrogen (LON) and other soil health indicators. The results indicate that PMC was 31% more and LON was 23% more in NT than in CT, whilst ST resulted in lower pH and had only 10%, 9%, and 24% more SON, STN, and LON, respectively, than CT in 0–60 cm profile. The SIC stock was negatively correlated with MBC, PMC, SON, STN, LON, TLN, and SIN, whilst positively correlated with depth, STC, and pH. After 9 years of conservation tillage, whilst depth‐wise distribution varied among tillage systems, soil C sequestration rate was negative in the 0–60 cm profile under both NT and ST compared with CT, mainly owing to more SIC accumulation in deeper depth of conventional system. These results show the complexity of soil C and N allocation under different tillage systems, with NT and ST supporting greater C and N storage in the surface soil and CT supporting more C and N storage in the deeper depth. Soil biological activity indicators appear to drive surface SOC accumulation, whilst soil pH and N availability influenced SIC accumulation in lower depths.

High‐frequency (470 kHz) ultrasonics‐assisted room temperature CO2 stripping and fate of Sono exposed solvent

AbstractBACKGROUNDThe conventional CO2 stripping process in solvent‐based postcombustion CO2 capture (PCCC) process uses heating to strip the CO2 (~120 °C). However, the challenges associated with this method are high energy consumption in degassing the CO2 from solvent, solvent loss and degradation resulting from the high –temperatures, resulting in high energy consumption typical of solvent‐based PCCC. The present study demonstrates the use of bath‐type sonication (470 kHz frequency) to remove CO2 from CO2 loaded 30 wt% Monoethanolamine under controlled temperature conditions. Solvent performance was evaluated following exposure to 2 h conventional heating and 75 h sonication.RESULTSIn a batch sono‐assisted process, CO2 stripping became possible at 17.5 °C compared to 102.2 °C using the conventional method. Increasing the sonication time led decreased carbon loading and increased stripping efficiency. The stripping rate was high at the initial stages of treatment. Evaluation of sono‐exposed solvents exhibited decreased pH during CO2 loading and decreased absorption capacity of the conventionally heated sample.CONCLUSIONThe sono‐assisted method consumes 3.57‐foldless energy than conventional heating. Its CO2 stripping rate was found to be higher within 5 min of sonication. Notably, the maximum temperature reached for the 1 h intervening mode of sonication at 470 kHz was 49.49 °C. The reduction in absorption capacity per hour of conventional heating was 24.5%, whereas for sonication it was <0.4% and solvent loss was 19.7% lower than conventional. There was no significant change in the color, pH and density of the sample. A 20.4% higher surface tension than that of the virgin sample was observed. © 2024 Society of Chemical Industry (SCI).

Steam Stripping for Recovery of Ammonia from Wastewater Using a High-Gravity Rotating Packed Bed

Steam stripping of ammonia from ammonia-rich wastewater (5000–20,000 mg/L) was conducted in a continuous-flow rotating packed bed (RPB) at a pH of 11. This study aimed to elucidate the influence of key operational parameters, including the steam-to-liquid ratio, rotational speed (ω), initial ammonia concentration, steam inlet temperature (TSi), and liquid inlet temperature (TLi), on critical performance metrics such as the ammonia removal efficiency (ARE), the volumetric liquid mass transfer coefficient (KLa), and the concentration of the recovered ammonia solution (CR). The findings revealed that a CR of 22.88 wt.% was achieved under the optimal conditions of a steam-to-liquid ratio of 0.175 kg/kg, an initial concentration of 20,000 mg/L, a TSi of 120 °C, and a TLi of 70 °C. Key experimental factors, including the initial ammonia concentration, TSi, and TLi, significantly impacted the achievement of higher ARE and CR values. The KLa values exhibited a decrease with the increase in the steam-to-liquid ratio, while they increased with ω. However, the KLa remained relatively consistent with ω values within the range of 600 to 1200 rpm. In comparison with prior studies, steam stripping of ammonia exhibits a higher ARE than air stripping with RPB and a higher CR than conventional stripping methods. Moreover, RPB requires a smaller size to achieve equivalent ARE compared to conventional stripping apparatuses. Thus, the steam stripping process with RPB equipment emerges as a suitable method for ammonia recovery from ammonia-rich wastewater.

Effect of two oxygen-inhibiting agents on the surface microhardness of giomer restorative materials.

To compare the effect of blue and conventional Mylar strips used as oxygen inhibiting agents on the surface microhardness of giomer restorative materials. A total 96 giomer specimens were prepared in disc-shaped molds 2 mm tall x 5 mm in diameter (ISO 4049: 2019-05). The specimens were grouped according to type of giomer: Beautifil II (BII) or Beautifil II LS (BIILS), and according to the type of Mylar strip: conventional, blue, or control group without strip. They were subsequently subjected to the Knoop (KHN) microhardness test. The database was analyzed with Stata SE v18 statistical software, and two-way ANOVA was performed. Interaction was found between the type of giomer and Mylar strip (p=0.039). Significant differences were found between surface microhardness values according to the type of giomer (0.001) and the type of Mylar strip (0.001). Beautifil II LS presented significant differences between conventional Mylar strip vs. without Mylar strip (43.58 ± 1.65 vs. 40.44 ± 2.12) and between blue Mylar strip and without Mylar strip (44.69 ± 1.75 vs. 40.44 ± 2.12). In the Bonferroni Post hoc test, a significant difference was found between Conventional Mylar Strip and without Mylar Strip (p=0.001) and Blue Mylar Strip and without Mylar Strip (p=0.001). The use of blue and conventional Mylar strips inhibits the oxygen layer on the Beautifil II and Beautifil II LS giomers, endowing them with high values of surface microhardness.

Development and Analytical Validation of a Surface-Enhanced Raman Scattering Paper Lateral Flow Immunoassay for Detection of the Ubiquitin C-Terminal Hydrolase-L1 Traumatic Brain Injury Biomarker.

Paper lateral flow immunoassays combined with surface-enhanced Raman scattering (SERS) technology have gained increasing attention due to their high sensitivity characteristics resulting from the amplified SERS signals of the plasmon-enhanced optical probes. In contrast to conventional colorimetric lateral flow strips, SERS paper lateral flow strips (SERS-PLFSs) are currently not commercially available for widespread use. Analytical validation is the key step for commercialization. In this work, we have developed a PLFS with a hierarchical SERS probe (gold-silver nanoparticle@Raman reporter@silica) for detection of the US Food and Drug Administration (FDA)-approved traumatic brain injury (TBI) protein biomarker, ubiquitin C-terminal hydrolase-L1 (UCH-L1), in blood plasma samples. Analytical validation has been performed on this SERS-PLFS in terms of the limit of detection (LOD), limit of quantification (LOQ), accuracy, precision, selectivity, and stability. The SERS-PLFS exhibits a reportable range of 0.2-100 ng/mL with a LOD of 0.08 ng/mL toward measurement of UCH-L1 in blood plasma. The SERS-PLFS has been applied to clinical TBI samples. The test results were compared with those from enzyme-linked immunosorbent assay (ELISA), demonstrating a strong correlation between the two analytical methods. This study has important implications in the commercialization of SERS-PLFSs for rapid TBI detection in clinical practice.

Fabrication of Raman reporter molecule–embedded magnetic SERS tag for ultrasensitive immunochromatographic monitoring of Cd ions and clenbuterol in complex samples

A rapid, simple but sensitive analytical method for the simultaneous monitoring of heavy metal ions and illegal additives in complex samples remains lacking. We reported a difunctional capture–detection surface-enhanced Raman scattering (SERS) immunochromatographic assay (ICA) for the direct detection of the heavy metal residue Cd ion (Cd2+) and illegal additive clenbuterol (CLE) with high sensitivity and specificity herein. A novel magnetic SERS tag (Fe@RAu) with a Raman reporter molecule–embedded raspberry-like Au shell was fabricated via a one-step reduction reaction that not only simplified the fabrication of common magnetic SERS nanomaterials but also improved SERS activity to increase detection sensitivity. The difunctional SERS–ICA enabled the fast magnetic enrichment of the target small molecules in complex specimens and ultrasensitive and quantitative determination of CLE/Cd2+ on the two test lines of the ICA system. The limits of detection of the developed method for CLE and Cd2+ were as low as 0.48 and 1.88 pg/mL, respectively, and about 2000 and 500 times lower than those of conventional AuNP-based ICA strips. The excellent practicability of Fe@RAu–ICA for real food samples analysis was also demonstrated, revealing the potential of the proposed assay for rapid and on-site screening of small-molecule pollutants.

A 5-year Evaluation of the Recurrence Rate Following Conventional Surgery and Ablation for Venous Insufficiency Revealed That Although Ablation Methods Were Employed, Conventional Surgery Was Not Abandoned

Objectives: Although conventional surgery (CS) has been less frequently employed in the treatment of great saphenous vein (GSV) in recent years, our clinic has not entirely abandoned this method. The objective of this study was to evaluate the recurrence and symptoms of patients treated with CS and radiofrequency ablation (RFA) for venous insufficiency (VI) 5 years ago. Methods: A retrospective review was conducted on the results of 233 patients who were treated for varicose veins in our clinic 5 years ago (all in the same year). Patients aged 20 years or older with clinical class C2 to C6 clinical, etiological, anatomical, pathophysiological and GSV diameter >5.5 mm, reflux degree of at least 0.5 s were treated with RFA or conventional stripping. A total of 121 patients were treated with CS and 112 patients were treated with RFA. The method to be applied to the patients was randomly assigned without prior planning. The quality of life and recurrence rate were evaluated using the venous clinical severity score before surgery and at 1-month and 5-year intervals following surgery. Results: In 2017, 233 patients were treated with RFA and CS methods due to VI (n=112, n=121). Clinical follow-up and examinations were conducted at the 1st week, 1st month, and 5th year after surgery. A comparison of the two groups revealed that RFA was non-inferior to CS in terms of clinical relapse after 5 years. However, in terms of recurrence, the situation was 16.36% (n=9) in CS and 46.80% (n=22) in RFA. Recurrence was found to be significantly associated with the operational technique (p<0.006). Furthermore, the recurrence rate was significantly higher among patients who underwent venous pouch excision simultaneously with the main procedure (90.84%, n=139) compared to those who did not (9.15%, n=14; p<0.05). Conclusion: As long as the recurrence rate of the traditional surgical stripping method remains low in the treatment of VI, this method will continue to be valuable. Although ablation methods are effective in our clinic, we have not abandoned traditional surgery. Since traditional surgery greatly reduces the risk of reoperation after many years, it should be recommended as an alternative choice to patients who are indicated for the procedure.

Aspects of rumble strip noise at distant ranges

One aspect of rumble strips that limits the use of these devices is noise intrusion for residents nearby the roadway. To investigate this issue as part of the NCHRP quieter rumble strip project, pass-by noise measurements on the rumble strips were made beyond the standard evaluation distance of 25 feet (7.5m). Distances varied from 48 feet (14.6m) to 381 feet (116m) more typical of distances for residences near the roadway. For this assessment, pass-by noise measurements and recordings on the rumble strips were made at distances using one test vehicle from the primary research. The measurements were for sinusoidal rumble strips with wavelengths of 13, 15, 16, and 17 inches (33.0, 38.1, 40.6, and 43.2cm). For comparison, measurements were also made for more standard, discrete grind rumble strips. For all strips, the frequency of the repetition rate was apparent as the vehicle approached the microphone location and to a lesser amount after the vehicle passed the microphone. It was also demonstrated that the overall A-weighted level fell-off at a higher rate than the level at the repetition rate. The 80 Hz tone from the sinusoidal strips was observed to be barely audible, unlike the 100 Hz tone for the conventional strips.

Ethanol removal by vacuum-assisted gas stripping: Influence of operating conditions

One way to overcome the inhibitory effects caused by ethanol on yeast cell growth is the use of extractive fermentation, whereby ethanol is removed from the fermentation broth as it is produced. The present work investigates ethanol removal from solution by vacuum-assisted gas stripping, which is a promising method for enhancing performance, compared to conventional gas stripping. Evaluation was made of the effects of carbon dioxide flow rate (ϕCO2), temperature (T), and pressure (P) on ethanol removal performance. Bench-scale assays were performed using a 2-L bubble column containing 10 % v/v ethanol solution, with monitoring of the gas and liquid phases by FT-MIR spectroscopy. The ethanol entrainment factor (FE) increased with ϕCO2 and temperature, but decreased at higher pressure. Only ϕCO2 had significant and positive effects on the concentration factor (FC) and selectivity (αE/W), within the operating ranges of the variables studied. An ethanol removal model was obtained that provided an accurate description of the process behavior, with good agreement between the experimental and simulated data. In addition, the energy requirement for ethanol removal by vacuum-assisted gas stripping in the bioreactor was lower than for the conventional stripping process.

Nitrogen recovery from reject water for improved sustainability of wastewater treatment

ABSTRACT Flows of reactive nitrogen (Nr) and greenhouse gas emissions from society are exceeding planetary boundaries, posing a serious risk to the stability of living conditions on Earth. Wastewater contains the largest flows of Nr in urban society, so recycling Nr from wastewater treatment plants (WWTPs) could reduce the climate impact and the need for new Nr. The reject water from dewatering anaerobically digested sludge contains high concentrations of Nr and recovery of this Nr would decrease the load on biological nitrogen removal processes, and thus nitrous oxide emissions. Simultaneously, the need for external carbon sources and energy for aeration will decrease. In a case study at Rya WWTP in Gothenburg, Sweden, three Nr recovery technologies were investigated: (1) conventional ammonia stripping to ammonium sulphate; (2) thermal stripping to ammonium sulphate and (3) distillation of ammonia from reject water to ammonia water. All three technologies were found to decrease the climate impact compared with the removal processes currently used at Rya WWTP for the removal of Nr. Recovery by distillation to ammonia water had the lowest climate impact, while conventional stripping minimised the energy requirement.

Clinical outcomes of radiofrequency ablation using a radiofrequency needle device for varicose ulcer: A non-randomized controlled prospective study.

To evaluate the short-term clinical outcomes of radiofrequency ablation (RFA) using a radiofrequency (RF) needle device for varicose ulcers. From September 2020 to September 2021, a total of 80 patients with varicose ulcers were included in this study. Based on the different surgical methods, the patients were divided into RF group and control groups, with 40 cases in each group. In the RF group, RFA was performed using an RF needle device and foam sclerotherapy was used for superficial veins. The control group was treated with conventional high-ligation stripping. The surgical data, hospitalization data, clinical efficacy, and postoperative complications of two groups were compared. Meanwhile, the correlation between RBC, HB, HCT, and ulcer healing time was analyzed. Compared to the control group, RF group had shorter surgery time, duration in the hospital, and less intraoperative bleeding (p < .05). The VCSS and CIVIQ scores in RF group were significantly higher than that in control group (p < .05). The healing time of ulcers was shorter in the RF group (x2 = 19.766, p = .000). The RF group had fewer postoperative complications. There was a positive correlation between RBC, HB, and HCT, and ulcer healing time (p < .05). The use of the RF needle device for RFA to treat patients with varicose ulcers showed acceptable short-term clinical outcomes with less incidence of trauma, faster recovery, and fewer complications.

Temperature modulation enables in situ growth of gallium oxide nanostructures on thin films exhibiting diverse morphologies

In this study, we successfully synthesized three gallium oxide thin films on (0001)-faceted Al2O3 substrates using hydrogen-reduced chemical vapor deposition (CVD) at different deposition temperatures, resulting in distinct morphologies and crystalline phases. These films consist of two pure-phase β-Ga2O3 films and one mixed-phase film comprising both β- and ε-Ga2O3 phases. The mixed-phase samples were subsequently annealed at high temperatures to obtain pure-phase β-Ga2O3 thin films. Furthermore, by precisely controlling the growth temperature, we achieved in-situ formation of Ga2O3 nanostructures (nanowires and nanoribbons) on the surface of the β-Ga2O3 thin films. The presence of different dominant crystal planes in the samples was confirmed through X-ray diffraction analysis (XRD) for verification purposes. In directly grown β-Ga2O3 films, the (−201) plane emerged as the primary crystallographic plane, while both the (−201) and (401) planes dominated in β-Ga2O3 films obtained via ε-Ga2O3 film annealing. Raman spectroscopy findings further supported these observations regarding the crystalline phase of the films as observed through XRD analysis. Scanning electron microscopy (SEM) images revealed distinct film morphologies resulting from variations in deposition temperatures. A flatter surface was observed when a higher proportion of ε-Ga2O3 was present in the film, however, regular cracking occurred after annealing. Atomic Force Microscope (AFM) images demonstrated that at a deposition temperature of 800 °C, regular steps were present on the film's surface. Mixed-phase films exhibited hillock morphology that disappeared after annealing, leading to a decrease in the surface roughness in root mean square (RMS) value. By elevating the growth temperature, a significantly enhanced density of gallium oxide nanoribbons can be seamlessly integrated onto the film surface. The transferred nanoribbons exhibit an ultra-thin profile with a minimum thickness of merely 12 nm, rendering them more slender and economically advantageous in comparison to conventional mechanical stripping methods. This study presents a CVD-based approach for growing gallium oxide thin films with varying morphologies by employing temperature modulation and demonstrates an innovative one-step method for growing nanostructures on gallium oxide films in situ, providing valuable insights for future device development involving gallium oxide.

Principal Component Analysis of a Real-World Cohort of Descemet Stripping Automated Endothelial Keratoplasty and Descemet Membrane Endothelial Keratoplasty Cases: Demonstration of a Powerful Data-Mining Technique for Identifying Areas of Research.

Principal component analysis (PCA) is a descriptive exploratory statistical technique that is widely used in complex fields for data mining. However, it is rarely used in ophthalmology. We explored its research potential with a large series of eyes that underwent 3 keratoplasty techniques: Descemet membrane endothelial keratoplasty (DMEK), conventional Descemet stripping automated endothelial keratoplasty (ConDSAEK), or ultrathin-DSAEK (UT-DSAEK). All consecutive DMEK/DSAEK cases conducted in 2016 to 2022 that had ≥24 months of follow-up were included. ConDSAEK and UT-DSAEK were defined as preoperative central graft thickness ≥130 and <130 μm, respectively. Seventy-six patient, disease, surgical practice, and temporal outcome variables were subjected to PCA, including preoperative anterior keratometry, the use of sulfur hexafluoride gas (SF6) versus air for primary tamponade, and postoperative best corrected visual acuity and endothelial cell density. Associations of interest that were revealed by PCA were assessed with the Welch t test or Pearson test. A total of 331 eyes were treated with DMEK (n = 165), ConDSAEK (n = 95), or UT-DSAEK (n = 71). PCA showed that ConDSAEK and UT-DSAEK clustered closely, including regarding postoperative best corrected visual acuity, and were clearly distinct from DMEK. PCA and follow-up univariate analyses suggested that in DMEK, 1) flatter preoperative anterior keratometry (average, K1, and K2) associated with more rebubbling (P = 0.004-0.089) and graft detachment (P = 0.007-0.022); 2) graft marking did not affect postoperative ECD; and 3) lower postoperative endothelial cell density associated with SF6 use (all P > 0.001) and longer surgery (P = 0.005-0.091). All associations are currently under additional investigation in our hospital. PCA is a powerful technique that can rapidly reveal clinically relevant associations in complex ophthalmological datasets.

A novel integrated lateral flow immunoassay platform for the detection of cardiac troponin I using hierarchical dendritic copper-nickel nanostructures

Cardiac troponin I (cTnI) is a critical biomarker for the diagnosis of acute myocardial infarction (AMI). Herein, we report a novel integrated lateral flow immunoassay (LFIA) platform for highly sensitive point-of-care testing (POCT) of cTnI using hierarchical dendritic copper-nickel (HD-nanoCu-Ni) nanostructures. The electrodeposited HD-nanoCu-Ni film (∼22 μm thick) on an ITO-coated glass substrate exhibits superior capillary action and structural integrity. These properties enable efficient sample transport and antibody immobilization, making it a compelling alternative to conventional multi-component paper-based LFIA test strips, which are often plagued by structural fragility and susceptibility to moisture damage. The biofunctionalized HD-nanoCu-Ni substrates were laser-etched with lateral flow channels, including a sample loading/conjugate release zone, a test zone, and a control zone. Numerical simulations were used to further optimize the design of these channels to achieve optimal fluid flow and target capture. The HD-nanoCu-Ni LFIA device utilizes a fluorescence quenching based sandwich immunoassay format using antibody-labeled gold nanoparticles (AuNPs) as quenchers. Two different fluorescent materials, fluorescein isothiocyanate (FITC) and CdSe@ZnS quantum dots (QDs), were used as background fluorophores in the device. Upon the formation of a sandwich immunocomplex with cTnI on the HD-nanoCu-Ni device, introduced AuNPs led to the fluorescence quenching of the background fluorophores. The total assay time was approximately 15 min, demonstrating the rapid and efficient nature of the HD-nanoCu-Ni LFIA platform. For FITC, both inner filter effect (IFE) and fluorescence resonance energy transfer (FRET) contributed to the AuNP-mediated quenching. In the case of CdSe@ZnS QDs, IFE dominated the AuNP-induced quenching. Calibration curves were established based on the relationship between the fluorescence quenching intensity and cTnI concentration in human serum samples, ranging from 0.5 to 128 ng/mL. The limits of detection (LODs) were determined to be 0.27 ng/mL and 0.40 ng/mL for FITC and CdSe@ZnS QDs, respectively. A method comparison study using Passing-Bablok regression analysis on varying cTnI concentrations in human serum samples confirmed the equivalence of the HD-nanoCu-Ni LFIA platform to a commercial fluorescence cTnI LFIA assay kit, with no significant systematic or proportional bias observed.

Establishment of a high-yield intercropping system for maize and legumes under rainfed conditions in eastern Bhutan

ABSTRACT Maize-legume intercropping is a sustainable strategy to improve maize production for smallholder farmers. Maize is a staple food crop in Bhutan and integration of legumes with maize has been considered as an alternative option towards enhancing maize production in the country. Here, we conducted two studies in eastern Bhutan: first study (2021) to identify suitable legumes for intercropping with maize and second study (2022) to evaluate the effects of different maize-soybean intercropping patterns on grain yield, land use efficiency, and economic benefits. The maize-soybean intercropping system showed better productivity and economic viability than the kidney bean and groundnut systems in both the sites. Row intercropping and strip intercropping with 2 rows of maize alternating with 2 rows of soybean (2 M:2S) spaced 0.3 × 0.3 m showed stable and consistently higher grain yield at Lingmethang and Wengkhar (LING = 6.05 t ha−1; WENG = 8.37 t ha−1). The land equivalent ratio (LING = 1.78; WENG = 1.73) and net return (0.16 million Nu. ha−1 for LING and 0.21 million Nu. ha−1 for WENG) were notably higher for these intercropping methods. Our results suggest that the integration of legumes between conventional maize planting density, row intercropping and strip intercropping (2 M:2S) spaced at 0.3 × 0.3 m would be beneficial for achieving higher productivity for smallholder farmers in eastern Bhutan.

Influence of Cropping Sequence and Tillage System on Plant-Parasitic Nematodes and Peanut (Arachis hypogaea) Response to Fluopyram Applied at Planting

Crop sequence and tillage can affect the yield of peanut (Arachis hypogaea L.) and other crops. Research was conducted from 2006 through 2022 to determine the response of peanut to previous crop sequences including corn (Zea mays L.) and cotton (Gossypium hirsutum L.) planted in continuous conventional tillage (e.g., disking, field cultivating, and bedding with in-row sub-soiling) or strip tillage (e.g., tilling a 45 cm section on rows spaced 91 cm apart using fluted coulters, rolling baskets, and in-row sub-soiling). In 2013, 2019, and 2022, the entire test area was planted with peanut. In 2019 and 2022, peanut was planted without or with fluopyram applied in the seed furrow at planting. Decreasing the number of years between peanut planting resulted in lower peanut yields compared with fewer years of peanut planting in the rotation sequence. Continuous conventional tillage and strip tillage resulted in similar peanut yields at one location, while the yield was lower at a second location when peanut was planted in continuous strip tillage. Fluopyram did not affect peanut yield regardless of previous crop rotation sequence, the number of years separating peanut plantings, or the tillage system. However, minor differences in the populations of plant-parasitic nematodes in soil were noted when comparing fluopyram treatment. The results from these experiments indicate that while fluopyram can reduce the populations of some plant-parasitic nematodes in soil, the magnitude of reduction does not translate into increases in peanut yield.

Transforming waste cellulosic fabric dyed with Reactive Yellow C4GL into value textile by a microwave assisted energy efficient system of color stripping

A million ton of cotton fabric is wasted during cutting process in garment industry as well as in textile dyeing industry due to faulty dyeing. Color stripping of cotton fabric has become a significant challenge in the textile industry because the harsh chemicals used in chemical stripping processes affects the quality of fabric very badly. Conventional stripping methods lead with severe effects due to prolonged treatment time and high chemical concentrations. Recently, microwave-assisted stripping techniques have been emerged as effective alternatives to improve stripping efficiency. In this research, the developed microwave assisted stripping system is improved by the application of Urea, which is utilized as a microwave absorber to further reduce stripping time, temperature, and chemical concentration kept focus on quality parameters of recycled cotton fabric. This study inspects the efficiency of microwave absorber-assisted alkali hydrolysis and reduction in terms of dye-fabric bond cleavage, chromophores removal, chemical consumption, and processing time and compared with sequential stripping, microwave assisted stripping without absorber and conventional methods. The results indicated that microwave absorber-assisted alkali hydrolysis and reduction achieved 90 % stripping efficiency by using lowest concentrations of chemicals, while sequential stripping yielded a stripping efficiency of 96 %. Similarly, microwave absorber assisted methods resulted in minor loss in tear strength and weight. These outputs highlight the superior performance of microwave absorber-assisted techniques, demonstrating their efficiency, novelty, time-saving nature, and reduced damage compared to other methods.

Smartphone-assisted electrochemiluminescence imaging test strips towards dual-signal visualized and sensitive monitoring of aflatoxin B1 in corn samples

Aflatoxins B1 (AFB1) contamination in agro-food holds great threaten to human and animal health. Conventional test strips for rapid AFB1 visualized monitoring remains challenged by improvement of sensitivity and matrix interference resistance. In this case, we developed a portable electrochemiluminescence (ECL) imaging test strip with dual-signal outputs for AFB1 quantification in corn samples. Ru-PEI@SiO2@Au nanospheres were synthesized for bonding with anti-AFB1 antibody and then colorimetrical signal-reported on test line through the capillary flow at strips. Meanwhile, ECL imaging signal of the constructed carbon-ink-based working electrode on polyvinyl chloride substrate of strips was exported under an applied potential of 1.25 V. The whole ECL test strips not only endowed convenient colorimetric responses but guaranteed quick-witted ECL image distinguishment even at extremely low AFB1 content. The detection limit of this ECL imaging-integrated mode was 10-fold lower than that of only colorimetric mode. Furthermore, satisfactory selectivity, reliability and practicability of the as-proposed ECL test strips were demonstrated. This work offered a promising platform for on-site, accurate and sensitive detection of pollutants in foods.

Resonant Acoustic Vibration-Assisted Cathode Stripping for Efficient Recycling of Spent Li-Ion Batteries

Abstract The emerging field of direct recycling for spent Li-ion batteries offers significant advantages, such as reduced energy expenses and minimized secondary pollution, when compared to traditional pyrometallurgical and hydrometallurgical methods. This is due to its direct utilization of the spent cathodes as raw materials. However, efficient harvesting of spent cathode particles remains a challenge. To address this issue, this technical brief is the first to incorporate resonant acoustic vibration technology (RAV) as an efficient method for stripping cathode powders from spent Li-ion batteries. Our findings indicate that RAV-based techniques can achieve a stripping efficiency of up to 92%. A comparative analysis with conventional stripping methods, such as magnetic stirring, sonication, and curling–uncurling, reveals that RAV coupled with heat treatment provides unparalleled scalability and efficiency, eliminating the need for post-processing. Furthermore, the resulting cathode powders retain their original polycrystalline particle structures, with no impurities, such as carbon black or small aluminum fragments detected. These findings highlight the promise of RAV technology for large-scale recovery of electrode powders and its potential role in direct recycling of spent Li-ion batteries.