Conventional Single-mode Fiber Research Articles

Broadband dispersion compensation and high birefringence photonic crystal fiber for CWDM/DWDM networks

In this study, we propose a new design based on photonic crystal fibers (PCFs) for broadband dispersion compensation in telecommunication networks. The proposed design has a hexagonal structure arrangement of air-holes rings of different diameters between the silica core and the cladding. The PCF properties like effective area, nonlinearity, dispersion slope, confinement loss, and birefringence are reported and discussed. For the best performance we present three designs A, B and C. Simulation results show that the three designs cover the six-telecommunication optical bands O-, E-, S-, C-, L- and U- bands (wavelengths ranging from 1260 to 1675 nm). Design A achieves a large negative dispersion value of about − 1716 ps/(nm.km) with relative dispersion slope equals to that of conventional single-mode optical fibers (SMFs) of about 0.0036 nm−1, which makes it very suitable for long-haul DWDM transmission systems. With a little modification in the core, designs B and C achieve much higher confinement ability and achieve a very large birefringence value for polarization mode dispersion and sensing applications. Design C is engineered to have exact opposite dispersion of SMF with zero dispersion at the wavelength 1310 nm, which makes it a promising design in CWDM transmission system. The numerical values have been investigated using the full vector finite element method.

Highly-Sensitive Polymer Optical Fiber SPR Sensor for Fast Immunoassay

A new type of human immunoglobulin G (IgG) sensors based on the surface plasmon resonance (SPR) in the low refractive index (RI) plastic optical fiber (POF) and an antibody immobilization method is presented. A 50-nm-thick gold film was formed on the polished D-shaped fiber surface by magnetron sputtering. The RI response of the POF sensor is 30 049.61 nm/RIU, which is 26.5 times higher than that of single mode fiber (SMF) SPR sensors. The proposed SPR biosensor can be developed by simple and rapid modification of the gold film with 11-mercapto undecanoic acid (MUA). Upon immobilization of the goat anti-human IgG antibody, the resonance wavelength shifts by 11.2 nm. The sensor can be used to specifically detect and quantify the human IgG at concentrations down to 245.4 ng/mL with the sensitivity of 1.327 7 nm per µg/mL, which offers an enhancement of 12.5-fold compared to that of the conventional SMF based SPR sensors. The proposed device may find the potential applications in the case of use at the point of care.

In situ characterization of optical micro/nano fibers using scattering loss analysis

We experimentally demonstrate the in situ characterization of optical micro/nano fibers (MNFs). The MNF (test fiber, TF) is positioned on a microfiber (probe fiber, PF) and simulated for the scattering loss at various PF and TF diameters. The TF is fabricated using chemical etching technique. The PF is a conventional single-mode fiber with an outer diameter of 125 μm. We measure the scattering loss along the TF axis at various positions i.e., diameters by mounting it on the PF. The diameter profile of the TF is inferred from the measured scattering loss and correlated with its surface morphology measurement. This work demonstrates an effective, low-cost, and non-destructive method for in situ characterization of fabricated MNFs. It can detect and determine the irregularities on the surface of OMNFs. It can also be used to quantify the local evanescent field. Detecting such local points can improve studies that are carried out using these fields in various sensing and related study domains. It is simple to implement and can be accessed by all domains of researchers.

Interconnectivity between effectively single-moded antiresonant hollow core fibres and conventional single-mode fibres

We review the topic, focusing first on a discussion of the key parameters, limits of coupling loss, and measurement techniques. We then follow by reviewing the literature, including mode-field adaptation methods, and assembly approaches. Finally, we briefly cover the topic of hollow core fibre connection with non-standard single mode fibres, and finish with a review of components that can be made directly within the connection. We conclude with a summary of key achievements and present our view on key remaining challenges.

Fabry-Pérot Cavities with Suspended Palladium Membranes on Optical Fibers for Highly Sensitive Hydrogen Sensing.

Hydrogen (H2) sensors are critical to various applications such as the situation where H2 is used as the clean energy for industry or the indicator for human disease diagnosis. Palladium (Pd) is widely used as the hydrogen sensing material in different types of sensors. Optical fiber H2 sensors are particularly promising due to their compactness and spark-free operation. Here, we report a Fabry-Pérot (FP)-cavity-based H2 sensor that is formed with a freestanding Pd membrane and integrated on a conventional single-mode optical fiber end. The freestanding Pd membrane acts both as the active hydrogen sensing material and as one of the reflective mirrors of the cavity. When the Pd film absorbs H2 to form PdHx, it will be stretched, resulting in a change of the cavity length and thus a shift of the interference spectrum. The H2 concentration can be derived from the amplitude of the wavelength shift. Experimental results showed that H2 sensors based on suspended Pd membranes can achieve a detection sensitivity of about 3.6 pm/ppm and a detection limit of about 3.3 ppm. This highly sensitive detection scheme is expected to find applications for sensing low-concentration H2.

Hollow-Core Optical Fibers for Telecommunications and Data Transmission

Hollow-core optical fibers (HCFs) have unique properties like low latency, negligible optical nonlinearity, wide low-loss spectrum, up to 2100 nm, the ability to carry high power, and potentially lower loss then solid-core single-mode fibers (SMFs). These features make them very promising for communication networks and similar applications. However, this class of fibers is still in development. Current applications are almost exclusively limited to low-latency data links for High-Speed Trading (HST); other uses are in the trial stage now. In this paper, we comprehensively review the progress in the development of HCFs including fiber design, fabrication and parameters (with comparisons to conventional single-mode fibers) and support technologies like splicing and testing. A variety of HCF applications in future telecom networks and systems is analyzed, pointing out their strengths and limitations. Additionally, we review the influence of filler gas and entry of contaminants on HCF attenuation, and propose a new fusion splicing technique, avoiding the destruction of the fiber’s photonic cladding at high temperature.

Miniature Temperature-Independent Curvature Sensor Based on a Phase-Shifted Long-Period Fiber Grating Using Deep Tapering

A miniature temperature-independent curvature sensor was proposed and prepared by using a phase-shifted long-period fiber grating (LPG) fabricated from deeply tapered conventional single-mode fibers (SMFs). As a typical example, a sensor made from a phase-shifted deeply tapered long-period grating (PS-DTLPG) with a length of 3.4 mm and a maximum curvature sensitivity of 12.05 nm/m <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-1</sup> was successfully demonstrated. The proposed curvature sensor is of the temperature-independence and has features of high sensitivity, high reliability, miniature size and low cost, which could have potential applications in structural health monitoring, especially for the medical industry and shape reconstruction.

CO2 laser-induced long-period fiber grating in the dispersion turning point

A CO2 laser-induced long-period fiber grating (LPFG) in the dispersion turning point (DTP) has been proposed in this work, which has demonstrated the possibility of fabricating LPFG with a shorter period of 115 μm in a thin single-mode fiber (SMF) without etching cladding. The LPFG working near DTP was also induced in a conventional SMF by CO2 laser after etching cladding, whose grating period was 196 μm. Then, the refractive index (RI) sensitivity of LPFG based on thin SMF was optimized by fully combining DTP and cladding reduction. Considering the sensor probe's mechanical strength comprehensively, the thin SMF cladding was etched to 51.03 μm to ensure cladding mode LP1,6 work near DTP, which can result in an average RI sensitivity of 2117.12 nm/RIU in the RI range of 1.33222 to 1.39018. Based on its excellent RI sensing performance, the proposed LPFG is a prospective sensor that can be applied to significant fields such as environmental, chemical, or biological parameters measurement. At the same time, this study provides a low-cost path to fabricate LPFG worked in DTP for most researchers.

Orbital Angular Momentum in Fibers

Orbital angular momentum (OAM) of light beams with helical phase front, as an alternative spatial dimension resource of photons, has attracted extensive attention over the past decades. Very recently, OAM in fibers has facilitated rapid development of various fiber-based applications, such as optical communications, optical manipulation, optical sensing, optical imaging, nonlinear optics, and quantum science. Comprehensive and in-depth understanding of OAM in fibers is of great interest to researchers in this area. Here, we give a tutorial overview of OAM in fibers. We first introduce the basic theories, including the eigenmode analysis method, mode coupling theory, and spin-orbit mapping of light in fibers. We then give a detailed classification of OAM fibers and discuss versatile spatial mode bases in fibers. After that, we review various OAM fiber designs, including conventional single-mode fibers, conventional multi-mode fibers, ring-core fibers, air-core fibers, photonic crystal fibers, negative-curvature hollow-core fibers, multi-core fibers, active fibers (e.g., erbium-doped fibers), etc. Besides, we describe the state-of-the-art commercial fiber manufacturing processes as well as testing and characterization methods for OAM fibers. We also review various active and passive OAM fiber devices. Moreover, we introduce several typical advanced applications based on OAM fibers, such as capacity scaling fiber-optic communications, remote vectorial Doppler velocimetry, super-resolution optical imaging, and high-dimensional quantum cryptography. Finally, we briefly discuss future challenges and prospects of OAM in fibers.

Development and stability analysis of an S-tapered optical fiber-based sensor structure.

In this paper, three S-tapered fiber (STF) structures with different diameters (40, 60, and 80µm) are fabricated using conventional single-mode fiber. First, the reproducibility of the proposed S-tapered structure is confirmed through an analysis of the diameter distribution. Considering the transmitted intensities of the three various diameter, S-tapered structures reveal that the STF with a 40µm diameter produces more evanescent waves and is more sensitive to external refractive index variations. Therefore, the STF structure with a 40µm diameter was evaluated for the detection of different concentration of glucose solutions, demonstrating that the structure has the potential to be utilized to develop a highly sensitive fiber sensor.

Theoretical investigations of weakly- and strongly-coupled multi-core fibers for the applications of optical submarine communications under power and fiber count limits.

The practical cable design for optical submarine communications has a limited fiber pair count due to the mechanical considerations of cable weight and size. Consequently, multi-core fibers (MCFs) could exhibit higher capacity than conventional single-mode fibers (SMFs) thanks to space division multiplexing (SDM). That is because the power supply to a submarine cable is fed by the voltage difference between shores. Under the power-limited condition, SDM improves the cable capacity by using more paths which outperforms the SMF link whose capacity approximately complies with a logarithmic relationship to optical power. At the same time, fiber nonlinearity can be alleviated by the reduced power density of transmitted light in MCFs, due to the increased spatial diversity and mode coupling among coupled cores. In this work, we theoretically investigate the potentials of MCFs including weakly-coupled multicore fiber (WC-MCF) and strongly-coupled multicore fiber (SC-MCF) as the propagation media for submarine communications across the Atlantic and the Pacific. To fairly compare the performances of SMFs- and MCFs-based submarine cables, the Gaussian noise (GN) model for SDM links is employed to optimize the systematic settings including spatial multiplicity and single span length. Then, we develop an SDM and wavelength division multiplexing (WDM) fiber transmission model based on coupled nonlinear Schrodinger equations (CNSE) to investigate the optical filed coupling effect in MCFs-based cables. The developed transmission model has been self-examined by measuring the inter-core crosstalk (IC-XT) and spatial mode dispersion (SMD), referring to the set values. As indicated by the theoretical analysis, the WC-MCFs cable exhibits a larger capacity than the SMFs cable, when the fiber pair count is limited below 32. Moreover, the SC-MCFs cable outperforms the WC-MCFs cable thanks to the reduced fiber nonlinearity due to the random mode coupling and the assistance of multiple-input and multiple-output digital signal processing (MIMO-DSP). At last, the marginal influences of IC-XT, SMD, and insertion loss of Fan-in and Fan-out couplers are also analyzed for the MCFs cable.

Optimized femtosecond laser direct-written fiber Bragg gratings with high reflectivity and low loss.

We propose and experimentally demonstrate a femtosecond laser plane-by-plane (Pl-b-Pl) technology for inscription of high-quality fiber Bragg gratings (FBGs). The spherical aberration (SA) was introduced to elongate the focal volume, and then combined with the scanning process, an expanded rectangular refractive index modification (RIM) region can be achieved. Such RIM regions exhibit a length of 15 µm and a width of 14 µm. Note that it consists of a negative region and a positive region. We have systematically studied the influence of the overlap between the RIM region and fiber core on the spectrum of FBG. After optimizing, the core of a conventional single-mode fiber (SMF) is covered completely by using the positive RIM region, resulting in a significant enhancement of the coupling strength coefficient (i.e., 3177.6 m-1). A 500 µm long FBG assembled by using these RIM regions can achieve a high reflectivity of 95.83%. Moreover, the cladding mode resonances in transmission spectrum are suppressed thoroughly, since the localized effect in RIM region was avoided. In addition, this FBG exhibits a high birefringence of 2.13 × 10-4. Therefore, the proposed fabrication method can be used to inscribe high-quality FBGs that could be used in many fields such as communication, fiber laser, polarization-selective filtering and multi-parameter sensing.

Collapsed photonic crystal fibre thermoluminescence dosimetry for external beam radiotherapy

In measuring exposure to ionizing radiation various detectors and techniques have been developed. Current investigation is of key TL dosimetric responses of Ge-doped collapsed photonic crystal fibre (PCF), a form offering the advantage of greater sensitivity compared to more conventional single-mode optical fibers. The PCF samples that have been studied herein have been used to obtain external photon beam percentage depth doses (PDD), elevated sensitivity being desirable in providing a basis for the capture of the range of doses. Using a linac operated at 6 and 10 MV, the results show a favourable comparison with ionization chamber values (typically to within 5%). Threshold dose, reproducibility, and dose-rate dependency have also been characterized.

Orthogonal single-mode helical Bragg gratings created in fiber cladding for vector bending measurement.

We demonstrate a novel, to the best of our knowledge, two-dimensional vector bending sensor based on orthogonal helical Bragg gratings inscribed in the cladding of a conventional single-mode fiber (SMF). The helical cladding fiber Bragg gratings (HCFBGs) are created by using a femtosecond laser direct writing technology and a quarter-pitch graded index fiber (GIF) is used in front of the HCFBGs to diverge the core mode into fiber cladding. In contrast to the multimode resonance observed in conventional cladding Bragg gratings inscribed by using a femtosecond laser point-by-point (PbP) or line-by-line (LbL) technology, the proposed HCFBGs exhibit stable narrowband single-mode Bragg resonance. An HCFBG with a low peak reflectivity of -50.77 dB and a narrow bandwidth of 0.66 nm was successfully fabricated by using a lateral offset of 45 µm between the HCFBG and the fiber core axis. Moreover, two orthogonal HCFBGs were fabricated in the SMF cladding and used for vector bending sensing. Strong orientation dependence could be seen in omnidirectional bending measurement, exhibiting a maximum bending sensitivity of up to 50.0 pm/m-1, which is comparable to that in a multicore FBG. In addition, both the orientation and amplitude of bending vector could be reconstructed by using the measured Bragg wavelength shifts in two orthogonal HCFBGs. As such, the proposed HCFBGs could be used in many applications, such as structural health monitoring, robotic arms, and medical instruments.

Fusion splicing of hollow-core to standard single-mode fibers using a gradient-index bridge fiber

High-performance interconnection between hollow-core fiber and conventional solid-core fiber is of great significance for a lot of promising applications of hollow-core fibers. The current problems for high-performance hollow-core fiber/solid-core fiber interconnection mainly involve mode field mismatch of the two fibers and the complex splicing process. Subject of study. We study fusion splicing of anti-resonant hollow-core fiber with low loss (0.52 dB) and conventional single-mode fiber using a convenient graded-index bridge fiber. Purpose of the work. We aim to eliminate the mode field diameter mismatch between anti-resonant hollow-core fiber and single-mode fiber and simplify the mode field diameter adaptation method and process. Method. We employ a convenient graded-index bridge fiber approach, where a gradient index fiber is first spliced with the single-mode fiber, and the mode interference within the graded-index bridge fiber causes periodic enlargement and shrinkage of the mode field diameter. By precise cutting of the graded-index bridge fiber, the mode field diameter can be well controlled and made approximately equal to the mode field diameter of the anti-resonant hollow-core fiber. After mode field diameter adaptation, an optimized arc discharge fusion splicing procedure is applied for the anti-resonant hollow-core fiber/single-mode fiber fusion splicing. Main results. A fusion splicing loss of about 0.52 dB is achieved, which involves nearly 0.42 dB mode-field-diameter-mismatch-induced loss and about 0.1 dB fusion splicing loss that is caused by the deformation of the anti-resonant hollow-core fiber. Practical significance. The developed approach is convenient and cost-effective, which can benefit a lot of applications of anti-resonant hollow-core fibers in future telecommunications, fiber gas lasers as well as fiber-optic sensing.

Double-Wire-Based Single Distributed Optical Fiber Strain Sensing Method in High-Temperature Environment

Optical strain sensors [optical fiber strain (OFS] based on optical frequency domain reflection (OFDR) are an optical sensor with great application value and the ability to achieve distributed detection. However, both the external ambient temperature and the strain contribute to the frequency shift of the Rayleigh scattering spectrum in the optical fiber during the measurement. This means that the problem of temperature compensation (TC) must be considered when detecting strain in the environment with temperature field, especially in high-temperature environment. In this article, a method of double-wire-based single optical fiber was proposed to aim at this problem, which makes one single fiber have two functions of TC and strain sensing at the same time. The contact strain sensing experiment was carried out on the conventional standard single-mode fiber (SMF)-128 polyimide-coated (PI) distributed OFS sensor (DOFSS) under high-temperature conditions (0 °C–300 °C). The TC for the strain measurement of optical fiber sensor-based OFDR was effectively realized by performing data fusion operation on the measurement results of TC and strain sensing, and the relationship between the temperature change rate and the compensation error rate (ER) was obtained. In addition, the noncontact fiber stretching sensing experiment under ultrahigh-temperature (50 °C–600 °C) conditions was carried out for the first time, which further verified the effectiveness of the method for the compensation of the fiber strain measurement error. Feasibility especially provides a simple and effective method for the application of strain measurement technology in high-temperature environment.

Heterogeneous optical network incorporating low-loss ring-core fiber and single-mode fibers seamlessly connected by all-fiber vortex (de)multiplexer

We propose and experimentally demonstrate heterogeneous optical network to make the space-division multiplexing (SDM) network with ring-core fiber (RCF) compatible with the legacy optical networks with conventional single-mode fiber (SMF). Two homemade all-fiber mode selective couplers are fabricated by fusing pre-tapered conventional SMF with multi-mode fiber (Type: Corning OM3), serving as orbital angular momentum (OAM) (de)multiplexer to enable seamless connection between heterogeneous optical network incorporating low-loss RCF (loss: 0.26 dB/km) based SDM network and ultra-low-loss SMFs (loss: 0.154 dB/km) based networks. We transmit 30-Gbit/s 8-ary quadrature amplitude modulation signals over two OAM modes (OAM1,1 and OAM2,1) in different mode groups without multiple-input multiple-output equalization techniques through 100-km heterogeneous RCF and SMF network (25-km ultra-low-loss SMF + 50-km low-loss RCF + 25-km ultra-low-loss SMF). The measured optical signal-to-noise ratio penalties for multiplexing transmission are less than 5.73 dB at a bit-error rate of 3.8 × 10−3, indicating that the demonstrated OAM-assisted heterogeneous optical network has a favorable performance.

High-Density Weak in-Fiber Micro-Cavity Array for Distributed High-Temperature Sensing With Millimeter Spatial Resolution

High-spatial-resolution distributed sensing at high temperature is crucial in many industrial areas, such as aero-engines, nuclear power, furnaces, and fuel cells. Here, we propose and demonstrate a large-scale multiplexed high-density weak in-fiber micro-cavity (MC) array for distributed high-temperature sensing with millimeter spatial resolution. The proposed in-fiber MC, featured by an intrinsic Fabry-Perot interferometer (IFPI) with a short cavity length of 100 μm and a low peak reflectivity of ∼−55 dB, was formed by two weak reflectors created in a conventional single-mode fiber (SMF) by using femtosecond laser point-by-point inscription. Several high-density MC arrays, consisting of identical weak IFPIs over 1000, were fabricated by using different femtosecond laser pulse energy to investigate the transmission loss (TL) of MC arrays. The experimental result shows that the TL induced by a single MC could be low as 0.0009 dB. Moreover, the high-temperature performance of the MCs was studied via cyclic heating and cooling between room temperature and 1000 °C, showing a temperature sensitivity of −2.29 GHz/°C (i.e., 18.4 pm/°C). Furthermore, distributed high-temperature sensing was demonstrated by employing the fabricated in-fiber MC array with the demodulation of optical frequency domain reflectometry, and a high spatial resolution of 1 mm was achieved at a high temperature of 1000 °C. As such, the proposed high-density weak in-fiber MC arrays are suitable for distributed high-temperature sensing in harsh environment, and hence have wide prospection of application in the fields of aerospace, nuclear power, metallurgy, and electrochemical industry.

Weakly Coupled Multicore Fiber Technology, Deployment, and Systems

Space-division multiplexing (SDM) technology is a promising candidate to achieve massive parallelism in optical fiber cables and overcome the capacity limitation of the conventional single-mode fiber (SMF). Among the several kinds of SDM fiber, a weakly coupled multicore fiber (MCF) is advantageous in that it can be easily upgraded for use in existing equipment and requires no complex signal processing for optical multi-input multi-output (MIMO). In this article, we discuss the progress and standardization activity of MCF technologies from the viewpoint of accelerating the practical application of SDM technology. We first describe the possible application areas of SDM fibers and then show the recent progress of the essential technologies to construct the MCF link: the MCF itself, its splicing and connectorization, and the input/output techniques. We also discuss the availability and deployability of MCF as a large-capacity transmission medium and detail the progress on establishing a new international standard for SDM technology, which includes both historical progress and more recent endeavors on the standardization of optical fiber cables and SDM technology in International Telecommunication Union Telecommunication Standardization Sector (ITU-T) and International Electrotechnical Commission (IEC). We close with a summary of MCF technology and its standardization activity with an eye to next-generation transmission systems and the long-term development of ultralarge capacity SDM transmission technology.

Randomly-Coupled Multi-Core Fiber Technology

Randomly-coupled multi-core fiber (MCF) technology has come to attract lots of attention because of its strong applicability to long-haul transmission systems. Compared with weakly-coupled MCFs with independent cores, it can simultaneously realize higher spatial channel density and ultralow transmission loss using existing ultralow-loss single-mode fiber (SMF) core designs. The strong mode coupling characteristics of randomly-coupled MCFs can provide favorable optical properties, such as suppressed accumulation of modal dispersion (MD), mode-dependent loss (MDL), and nonlinear impairments. This article gives an overview of randomly-coupled MCF technology advancements. First, we describe the classification and design of randomly-coupled MCFs and explain what the randomly-coupled MCFs are and how they are designed. State-of-the-art randomly-coupled MCFs can accommodate four, seven, or 12 cores in a standard 125- <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\mu \text{m}$ </tex-math></inline-formula> cladding while achieving ultralow transmission loss and/or small MD, which are very promising for long-haul transmission media. Next, we present the methods to characterize the optical properties of randomly-coupled MCFs and the difference compared to conventional SMF measurements. We also show the low-loss low-MDL connectivity of this type of MCF and the cabling that can suppress MD. A field-deployed randomly-coupled MCF cable testbed is also presented, which confirmed the favorable optical properties of randomly-coupled MCFs after deployment. Then, multi-core amplifier technologies are briefly summarized, and finally, we discuss the performance improvements in the transmissions over randomly-coupled MCFs and suitable application areas.