Current Controlled Conveyor Transconductance Amplifier Research Articles

A novel resistorless memristor emulator circuit and its implementation of chaotic Jerk system

This work presents a novel resistorless memristor emulator circuit designed in both grounded and floating configurations. The grounded memristor consists of a Current-Controlled Current Conveyor Transconductance Amplifier (CC-CCTA) and a capacitor. On the other hand, a floating memristor includes a CC-CCTA and a capacitor, along with an additional Operational Transconductance Amplifier (OTA). These proposed emulators are electronically controllable owing to the internal structures of active elements. Theoretical analysis and simulation results have been obtained for the proposed designs. Simulation results have been conducted utilizing the LTspice program and TSMC 180 nm technology has been used for internal structures. In these results, the effects of the changing capacitor values, different frequencies, electronic tunability, reactions to temperature change, and pulse response have been investigated. Subsequently, a chaotic Jerk circuit has been implemented incorporating the proposed memristor emulator. The chaotic behavior of the floating memristor has been investigated using the LTspice simulation software.

Electronically Tunable Sinusoidal Oscillator Using Only Single Current-Controlled Current Conveyor Trans-Conductance Amplifier

This work presents a wide frequency range sinusoidal oscillator design that relies on only one active component, a current-controlled current conveyor trans-conductance amplifier, and a few passive components. It just employs two grounded and non-floating capacitors and one resistor to complete the procedure. This design has the advantage of allowing the oscillation frequency and condition to be adjusted not only electronically, but also separately, without affecting the values of any passive components. To verify the functionality and usefulness of the developed sinusoidal oscillator circuit, ORCAD PSPICE simulations are done using 0.18 um process parameters for complementary metal oxide semiconductor technology. The obtained results demonstrate its application to a wide range of frequency generation without the need for additional components, hence validating the theoretical expectation.

A simple sinusoidal quadrature oscillator using a single active element

This study describes a simple design for a single active element sinusoidal oscillator with a quadrature signal. A current conveyor transconductance amplifier (CCTA), a single resistor, and two grounded capacitors are used in the first circuit. The second circuit is improved by using a current-controlled current conveyor transconductance amplifier (CCCCTA) and two grounded capacitors without a passive resistor, which means the grounded capacitor is suitably implemented for the IC fabrication. The oscillation condition and frequency of both circuits can be controlled using the same method that concurrently adjusts the DC bias current and the resistance as well as the oscillation frequency can be independently adjusted by capacitances. The CCTA is achieved by cascading the integrated circuits (IC) AD844 and LM13700, made by Analog Devices Corporation and Texas Instruments, respectively, which are available for commercial purchase. The sinusoidal quadrature signals in the time-domain and frequency-domain can be shown with computer simulations and the results of experiments. The Monte Carlo Analysis is also utilized to examine the oscillation frequency with the influence of passive element tolerance errors. The predicted oscillation frequency has a standard variation of about 20.04 kHz, with a maximum frequency of approximately 346.89 kHz and a minimum frequency of approximately 259.09 kHz. In addition, the mean and median frequencies are 296.10 and 293.98 kHz, respectively. The results of this study indicate that computer simulation and experiment are similar to a theoretical analysis, making them suiTable for use in the teaching of electrical and electronic engineering

Improved Current Mode Biquadratic Shadow Universal Filte

In this paper, an improved single-input-multiple-output (SIMO) current-mode biquadratic shadow universal filter (SUF) is realized using two new variants of second-generation current conveyors (CCIIs), namely current conveyor cascaded transconductance amplifier (CCCTA) and extra-X current controlled conveyor transconductance amplifier (EX-CCCTA). The low pass and the band pass outputs of a non-shadow universal filter (NSUF), consisting of CCCTA, are utilized through two amplifiers' feedback paths using one EX-CCCTA to realize the proposed SUF. It is resistorless and uses two grounded capacitors only. All the five standard responses of SUF, such as low pass (LP), high pass (HP), band pass (BP), band-reject (BR), and all pass (AP), are obtained through the proposed circuit simultaneously. The important achievement of SUF over the NSUF is the ease of orthogonal tuning of the pole frequency (w o ) and quality factor (Q o ) with the bias current of CCCTA and EX-CCCTA. It is suitable for full cascadability because of proper input and output impedances. Moreover, it eases the integrated circuit implementation because of all grounded capacitors and no resistor. It does not possess any component matching constraints and consumes only 3.73mW power. The theoretical results have been validated through 180nm technology in Cadence Virtuoso.

Simple Current-Mode Squaring and Square-Rooting Circuits: Applications of MO-CCCCTA

This work provides new designs of simple current-mode squaring and square-rooting circuits using multiple-output current controlled current conveyor transconductance amplifier (MO-CCCCTA) as an active building block. Since the proposed circuits need no other external components, they are capable of high-frequency operation and well fitted for IC fabrication. Furthermore, they are insensitive to ambient temperature and their gains can be controlled easily by adjusting the bias currents of MO-CCCCTA. Additionally, the effects of MO-CCCCTA non-idealities on the designed circuits have also been investigated and discussed. Simulation results generated through PSPICE software using TSMC 0.18 µm CMOS process parameters have been presented to justify the theoretical analysis. The static power consumption, bandwidth, and maximum linearity error in dc transfer characteristic measurement for the square-rooting circuit are found to be 0.17 mW, 445.63 MHz and 1.12 %, while for the squaring circuit they are 0.326 mW, 61.15 MHz and 2.38 %, respectively. The application of the reported circuits as a 2-input vector summation circuit has also been included to strengthen the design ideas.
 HIGHLIGHTS
 
 Simple structures of fully integrable current-mode squarers and square-rooters with low component count and lower power dissipation
 The circuits are insensitive to temperature drift and their gains can be controlled easily by adjusting the bias currents of MO-CCCCTA
 Bandwidth, static power dissipation, linearity error of square-rooter are 445.63 MHz, 0.17 mW & ≤ 1.12 %; and for the squarer 61.15 MHz, 0.326 mW & 2.38 %, respectively
 
 GRAPHICAL ABSTRACT

Improved current-mode wave active filter

ABSTRACT In this paper, a resistorless improved wave active filter (WAF) is presented using a comparatively new current-mode building block, namely extra X current-controlled current conveyor (EX-CCCII). The proposed wave active filter is designed in the current mode. The incident and reflected waves are used for designing the basic wave active elements, namely series and shunt inductors (L) and capacitors (C). The novelty of the circuit is that the mathematical operations like lossy integrator, unity gain amplifier, summation, and subtraction, required to realise the wave active elements, are accomplished by judiciously using the port relationships of EXCCCII. As a result of which the proposed circuit is compact and uses only two EXCCCIIs and one grounded capacitor for the realisation of wave elements (L and C). One 3rd and one 4th order Butterworth wave active filters are designed using EX-CCCII-based wave elements and simulated in cadence using 0.18 µm TSMC CMOS technology. The comparison indicates that the proposed WAF uses minimum numbers of analog building blocks (ABBs) and consumes the least power; moreover, the performances such as noise, percentage total harmonic distortion (%THD), and electronic controllability of cut-off frequency of the filters are also reported. Abbreviations: ABB: analog building block; FDNR: frequency-dependent negative resister; WAF: wave active filter; THD: total harmonic distortion; OTA: operational transconductance amplifier; CFOA: current feedback operational amplifier; VDTA: voltage differencing transconductance amplifier; OTRA: operational transresistance amplifier; CCDDCCTA: current-controlled differential difference current conveyor transconductance amplifier; DVCCCTA: differential voltage current-controlled conveyor transconductance amplifier; DVCCTA: differential voltage current conveyor transconductance amplifier; EX-CCCII: extra X current-controlled conveyor

An Electronically Adjustable Waveform Generator

A novel electronically adjustable square/triangular waveform generator has been introduced in this paper. The proposed circuit employs one active element, the multi-output current-controlled current conveyor transconductance amplifier, and one passive component grounded capacitor only. The resistorless realization of the presented generator provides a good advantage in terms of integrated circuit fabrication. In the offered circuit, the frequency and amplitude of the output square wave are electronically tunable by means of relevant bias currents. Additionally, the upper and lower threshold levels are electronically controllable by the respective bias current. On the contrary, electronically adjusting of the duty cycle of output waveform is possible via the external DC current. The generator circuit is simulated with TSMC 0.18[Formula: see text][Formula: see text]m technology parameters and SPICE. Moreover, the introduced circuit is implemented by using commercially available active devices and thus it is also verified experimentally.

Arbitrary Waveform Generators Using Current-Controlled Current Conveyor Transconductance Amplifier and Current Conveyor Analog Switches

This paper presents a new amplitude modulation (AM), frequency modulation (FM), amplitude shift keying (ASK), frequency shift keying (FSK), phase shift keying (PSK) and quadrature amplitude modulation (QAM) waveform generators using current current-controlled conveyor transconductance amplifier (CCCTA) and current conveyor analog switches (CCASs). The CCCTA around with capacitors and resistors are used to generate high-frequency carrier which is worked as a quadrature oscillator. The oscillating frequency of oscillator can be controlled using the bias current of CCCTA, therefore FM and FSK waveforms can be obtained by applying information signal through the bias current of CCCTA. Unlike previous waveform generators, proposed circuit uses second generation current conveyor (CCII) to work as CCAS and AM, ASK, PSK and QAM waveforms can be obtained by putting information signals to control switches that realized using CCIIs. The proposed circuit has been simulated using 0.18[Formula: see text][Formula: see text]m CMOS [Formula: see text]-well process from TSMC. The simulation results are used to confirm workability of the proposed circuit.

Realization of Voltage-mode Multifunction Biaquadratic Filter Using Minimum Number of Active Element

The realization of voltage-mode multifunction biquadratic filter has been presented in this research contribution. The proposed circuit contains three input voltage nodes and one output voltage node. The structure of proposed filter is simple consisting of one modified current controlled current conveyor transconductance amplifier (M-CCCCTA) as active building block with one resistor and two capacitors. With electronically controllable property of M-CCCCTA, the parameters, natural frequency (ω0) and quality factor (Q) are electronically controlled by changing the external DC bias currents of the M-CCCCTA. The tuning characteristic of Q is also done without effect the w0. In the same circuit construction, five second order filter responses, all-pass, high-pass (HP), band-reject (BR), low-pass (LP) and band-pass (BP) functions are obtained. The output filter responses are obtained with applying appropriate input voltage to input node without the matching condition of active and passive elements. The performances of the proposed biquadratic filter have been verified through Pspice simulation in TSMC 0.25 μm CMOS technology parameters.

Electronically Tunable Current Controlled Current Conveyor Transconductance Amplifier-Based Mixed-Mode Biquadratic Filter with Resistorless and Grounded Capacitors

A new electronically tunable mixed-mode biquadratic filter with three current controlled current conveyor transconductance amplifiers (CCCCTAs) and two grounded capacitors is proposed. With current input, the filter can realise lowpass (LP), bandpass (BP), highpass (HP), bandstop (BS) and allpass (AP) responses in current mode and LP, BP and HP responses in transimpedance mode. With voltage input, the filter can realise LP, BP, HP, BS and AP responses in voltage and transadmittance modes. Other attractive features of the mixed-mode biquadratic filter are (1) the use of two grounded capacitors, which is ideal for integrated circuit implementation; (2) orthogonal control of the quality factor (Q) and resonance angular frequency (ωo) for easy electronic tenability; (3) low input impedance and high output impedance for current signals; (4) high input impedance for voltage signal; (5) avoidance of need for component-matching conditions; (6) resistorless and electronically tunable structure; (7) low active and passive sensitivities; and (8) independent control of the voltage transfer gains without affecting the parameters ωo and Q.

Voltage-Mode and Current-Mode Resistorless Third-Order Quadrature Oscillator

This paper presents the realization of a resistorless third-order quadrature oscillator using two multiple-output current controlled current conveyor transconductance amplifiers (MO-CCCCTAs) and three grounded capacitors. The proposed circuit provides two quadrature voltage outputs, two high-impedance quadrature current outputs, and one high-impedance amplitude-controllable current output. The proposed oscillator satisfies the industrial requirement for amplifier and modulation signals and phase shift keying signals, when the input bias current of the second MO-CCCCTA is used as a modulating signal. Its oscillation condition and oscillation frequency can be adjusted independently by two different bias currents of MO-CCCCTAs. The structure of resistorless and only grounded capacitors suggests that the proposed oscillator can be easily implemented in an integrated circuit.

Systematic synthesis approach for floating gyrators employing single z ‐copy CCCCTA

A systematic synthesis approach for floating gyrators employing single z-copy current-controlled current conveyor trans-conductance amplifier (CCCCTA) is presented in this work. Initially, the pathological models of two types of the CCCCTA, namely z-copy z +-output CCCCTA (CCCCTA+) and z-copy z −-output CCCCTA (z-copy CCCCTA−), are derived by virtue of the nodal admittance matrix (NAM) expansion method. Moreover, these models are then used in the synthesis of floating gyrator using single z-copy CCCCTA. Two floating gyrators are acquired by expanding the NAM of floating gyrator. The synthesised gyrators employ one z-copy CCCCTA and a grounded admittance. Adjusting bias currents of the CCCCTA can tune the parameter of the gyrators. The hand analysis and PSPICE simulation show that the used synthesis method is simple, systematic and valid.

Systematic synthesis of CCCCTA-based T-T filters using NAM expansion method

ABSTRACTIn the light of nullor-mirror models for current-controlled current conveyor trans-conductance amplifier (CCCCTA), initiating the admittance matrices of the Tow-Thomas (T-T) filter, three different types of the T-T filter are synthesised by means of the nodal admittance matrix (NAM) expansion method. The type A filter, which employ one CCCCTA, one grounded resistor and two grounded capacitors, has eight different forms, the type B filter, which employ one CCCCTA, two grounded capacitors and a second-generation current-controlled conveyor (CCCII) or an second-generation inverting current-controlled conveyor (ICCCII) or an operational trans-conductance amplifier (OTA), has 64 different forms and the type C filter employing one CCCCTA and two grounded capacitors has eight different forms. In all, 80 voltage-mode/current-mode T-T filter circuits are obtained. Because of using canonic number components, the circuits are highly desirable from the viewpoint of IC fabrication and their parameters can be electronically tuned through tuning bias currents of CCCCTAs. The hand analysis and computer simulation results have been provided to support the synthesis method.

On the Realization of CMOS Current-Controlled Current Conveyor Transconductance Amplifier (CCCCTA) with Linear Control of g<sub>m</sub>

In this paper, arealizationcurrent controlled current conveyor transconductance amplifier (CCCCTA)is presented astheactiveelement.Thisdesignwas based on aCMOStechnology of AMIS 0.35μm (MOSIS).The PSPICE simulation was used to study the performances of the proposed circuit. It was found that the abilities of differential-pair CCCII circuit and Electronically current-tunable (EOTA) can be achieved using the supply voltages of ±1.5volts and the transconductance gain of the circuit can be linearly tuned.

Current Mode Universal Filter Using Single Current Controlled Differential Difference Current Conveyor Transconductance Amplifier

This research paper contains a new electronically tunable current-mode biquadratic universal filter using a new active building block; current controlled differential difference current conveyor transconductance amplifier (CCDDCCTA). The proposed filter provides the following important and desirable features: (i) One can use only one CCDDCCTA and two capacitors; (ii) One can get low pass (LP), band pass (BP), high pass (HP), notch (NF) and all pass (AP) current responses from the same configuration without any alteration; (iii) Passive components are grounded, which ease the integrated circuit implementation; (iv) Responses are electronically tunable; and (v) Sensitivity is low. Moreover, the non-ideality analysis shows that the parasitic passive components can be compensated for the proposed circuit. The functionality of the design is verified through SPICE simulations using 0.25 μm CMOS TSMC technology process parameters. Simulation result agrees well with the theoretical analysis.

NAM expansion method for systematic synthesis of floating gyrators using CCCCTAs

This paper presents a nodal admittance matrix expansion method for systematically synthesizing floating gyrators using current controlled current conveyor transconductance amplifiers (CCCCTAs). After describing nullor---mirror models of the CCCCTAs, class I and II gyrators are synthesized by means of NAM expansion method. The class I gyrators employing a CCCCTA and a current-controlled current conveyor have 16 equivalent realizations, and the class II gyrators employing two CCCCTAs have 24 equivalent realizations. Having used canonic number of components, the circuits are easy to be integrated and their parameters can be electronically tuned through tuning bias currents of CCCCTAs. Finally, as an example, the MULTISIM simulation results of a notch filter constructed by using a class II gyrator are presented to verify the realizability of the derived circuits.

Simple BiCMOS CCCTA design and resistorless analog function realization.

The simple realization of the current-controlled conveyor transconductance amplifier (CCCTA) in BiCMOS technology is introduced. The proposed BiCMOS CCCTA realization is based on the use of differential pair and basic current mirror, which results in simple structure. Its characteristics, that is, parasitic resistance (R x) and current transfer (i o/i z), are also tunable electronically by external bias currents. The realized circuit is suitable for fabrication using standard 0.35 μm BiCMOS technology. Some simple and compact resistorless applications employing the proposed CCCTA as active elements are also suggested, which show that their circuit characteristics with electronic controllability are obtained. PSPICE simulation results demonstrating the circuit behaviors and confirming the theoretical analysis are performed.

Electronically tunable mutually coupled circuit using only two active components

A new circuit for realisation of the mutually coupled circuit, which is also called the synthetic transformer, is proposed. The proposed circuit uses two current controlled current conveyor transconductance amplifiers (CC-CCTAs), one grounded resistor and two grounded capacitors. The primary self-inductance, the secondary self-inductance and the mutual inductance can be independently controlled and can be tuned electronically by changing the biasing current of the CC-CCTAs. It uses two grounded capacitors which are suitable from the point of integrated circuit implementation. It has a good sensitivity performance with respect to tracking errors and passive components. The validity of the proposed circuit is demonstrated by PSpice simulations.

Current Controlled Differential Difference Current Conveyor Transconductance Amplifier and Its Application as Wave Active Filter

This paper proposes current controlled differential difference current conveyor transconductance amplifier (CCDDCCTA), a new active building block for analog signal processing. The functionality of the proposed block is verified via SPICE simulations using 0.25 μm TSMC CMOS technology parameters. The usefulness of the proposed element is demonstrated through an application, namely, wave filter. The CCDDCCTA-based wave equivalents are developed which use grounded capacitors and do not employ any resistors. The flexibility of terminal characteristics is utilized to suggest an alternate wave equivalents realization scheme which results in compact realization of wave filter. The feasibility of CCDDCCTA-based wave active filter is confirmed through simulation of a third-order Butterworth filter. The filter cutoff frequency can be tuned electronically via bias current.

An Active-Only Temperature-Insensitive Current-Mode Biquad Filter Based on Differentiator Structures Employing CCCCTAs

This article presents an active-only current-mode universal biquad filter performing three standard functions: low-pass, high-pass and band-pass function, which can be readily modified to achieve the rest functions (band-stop and all-pass). The circuit principle is based on active-only circuit designed by using differentiators which are constructed from current controlled current conveyor transconductance amplifier (CCCCTA) cooperating with an internally frequency compensated operational amplifier (OA). The features of the circuit are that: the pole frequency and quality factor can be independently tuned via the input bias currents and it is ideally temperature-insensitive, its circuit description is very simple, consisting of 3 CCCCTAs and 2 operational amplifiers, and the proposed circuit is very appropriate for further developing into integrated circuit architecture. The PSpice simulation results are shown. The given results agree well with the theoretical anticipation.