Controllable Transmission Zeros Research Articles

A novel 3D metal printing in‐line bandpass filter with multiple controllable transmission zeros

AbstractIn this paper, a novel three‐pole bandpass filter with a pair of controllable transmission zeros (TZs) is proposed first. The proposed structure is based on asymmetric dual‐postresonators and two external resonators. The fundamental mode and the first higher mode of the asymmetric dual‐postresonators are used as the nonresonant mode and the resonant mode separately. The nonresonant mode generates direct source to load negative coupling, thus providing one TZ located below the passband. The asymmetric dual‐postresonators and one of the external resonators R3 form a magnetically coupled cascaded triplet unit to produce the other TZ above the passband. Therefore, these two TZs are independently controlled. Moreover, the filter has a good quality factor (), of around 2700, compact size and an excellent out‐of‐band performance. For further suppressing the harmonic response and improving the processing accuracy, a six‐pole bandpass filter with harmonic suppression is designed and fabricated by using metal 3D printing technology. The measured result matches well with the simulated one, which verifies the accuracy of the method.

Design of highly selective balanced bandpass filter with wide differential-mode stopband and high common-mode suppression

A highly selective and wide stopband bandpass filter (BPF) with multiple transmission poles (TPs) and transmission zeros (TZs) has been proposed. The BPF employs a box-like coupling structure consisting of two half-wavelength resonators and a dual-mode open stub loaded resonator, enabling the generation of two TZs and four TPs. Three controllable TZs are obtained by adding an annular spiral open stub to the terminal of the input and output coupling lines, which significantly improves the selectivity of the BPF. To achieve a wide stopband characteristic, a wide stopband unit with three additional TZs is cascaded within the structure. A balanced BPF is realized by introducing a microstrip-slotline-microstrip balun structure to the input and output ports of the proposed BPF. Experimental results validate the feasibility of the proposed BPF and balanced BPF applied in 2.45 GHz ISM band. The introduction of eight TZs gives the BPF a 20 dB rectangular coefficient of 1.3 with an upper stopband exceeding than 12 GHz. The balanced BPF can achieve 40 dB of high common-mode(CM) suppression in the passband, while differential-mode (DM) transmission is close to the performance of the proposed BPF. The minimum insertion loss for BPF and balanced BPF is 0.8 dB and 1.3 dB, respectively.

A high-selectivity ceramic bandpass filter with controllable transmission zeros

Abstract This paper proposes a microstrip filter with controllable transmission zeros based on the λ/4 stepped impedance resonator. This filter utilizes hybrid electric-magnetic coupling to generate transmission zeros, which can improve selectivity and stop-band performance. A fifth-order filter is designed and manufactured on a ceramic substrate with a center frequency of 26 GHz, bandwidth of 2 GHz and the signal suppression level is better than 42.51 dB from 10 to 22.8 GHz and 48.23 dB from 29.1 to 40 GHz. Furthermore, the proposed filter has a compact size of 2.074 × 1.071 mm (0.566λ g × 0.292λ g ).

Compact dual‐band bandpass filter based on EMSICC and CPW resonator with excellent design flexibility

AbstractIn this letter, a novel dual‐band bandpass filter (BPF) with independently controllable center frequencies, bandwidths, and transmission zeros (TZs) is presented. The proposed BPF is realized by using eighth‐mode substrate‐integrated circular cavities (EMSICCs) and coplanar waveguide (CPW) resonators. The CPW resonators are embedded in the upper surface of the EMSICCs, allowing for a compact size without additional circuit dimensions. Finally, a dual‐band BPF for WLAN is designed and fabricated with center frequencies of 2.45 and 5.2 GHz. The measured results closely align with the simulated ones, validating the performance of the filter. Multiple TZs are generated by cross‐coupling and source‐load coupling, which results in good out‐of‐band rejection performance.

A new electric coupling and its applications on millimeter-wave SIW filter with high selectivity and controllable TZs

In this paper, a novel simple horizontal electric coupling (SHEC) structure is proposed, which only requires a single elliptical ring slot to be etched at the top layer of the substrate between the two adjacent SIW cavities. The working mechanism of SHEC is revealed using the equivalent magnetic current theory. The results indicate that the ring slot is divided into two semi-elliptical slots by the via-hole, and the induced electric fields generated by equivalent magnetic current near the slots enhance the extremely weak electric field intensity at the edge of the SIW cavities, resulting in the formation of electric coupling between the adjacent two cavities. As a verification, a fourth-order SIW filter operating at 27.96 GHz was designed based on the SHEC structure. The filter exhibits high selectivity with sharp roll-off of 114/105 dB/GHz and obtains controllable transmission zeros (TZs) by changing the size of the elliptical slot. Additionally, the proposed SHEC design has a regular via-holes arrangement and does not require etching slot on the bottom layer of the substrate, making it easy to accurately process, integrate, and package, providing a new approach for the design of millimeter-wave filters.

Third‐order filtering crossover using dual‐mode resonator for high‐isolated channels

SummaryThis paper proposes a high‐selective crossover with a third‐order filtering characteristic, high passband isolation, and multiple controllable transmission zeros based on a coupled topology using single‐ and dual‐mode resonators. By virtue of the odd‐ and even‐mode feature of the stub‐loaded dual‐mode ring resonator, not only can the two resonant modes for different passbands be relatively independently controlled, but also better isolation can be achieved. With a single‐mode resonator and stub‐loaded dual‐mode resonant coupling topology, the resultant crossover can perform third‐order filtering performance in two distinct passbands/channels and generate several transmission zeros outside the desired bands to improve the isolation between the passbands. Experimental results demonstrate that, compared with conventional works, the filtering order of the proposed crossover is promoted and its passband isolation can be significantly improved by about 8 dB. The proposed work may facilitate its widespread applications in high‐performance multichannel integrated microwave systems for avoiding interference between multiple intersecting signal paths.

A single‐layered balanced filtering crossover with high selectivity based on square patch resonator

AbstractA new design of single‐layered balanced filtering crossover with high selectivity based on square patch resonator is proposed. Originated from the degenerate modes, that is, TM12 and TM21 on square patch resonators, the feasibility of intrinsic common‐mode (CM) suppression and channel isolation is conceived. For demonstration, a first‐order balanced crossover prototype is designed. Afterwards, to enhance selectivity, a square patch resonator is subtly divided into two identical parts and then introduced into the prototype. Hence, a balanced filtering crossover with a fifth‐order Chebyshev response is formed. Furthermore, stubs are deployed between adjacent patch resonators to introduce mixed couplings. Thus, two controllable transmission zeros are obtained, and better out‐of‐band suppression is achieved. Ultimately, the proposed crossover is fabricated and measured. High performance in terms of differential‐mode filtering response, in‐band CM suppression and channel isolation demonstrates the feasibility of the proposed method.

Synthesis Design of Multiband Bandpass Filters Employing Multimode Bandstop Resonators With Star-Like Topology

Multimode resonators (MMRs) can be utilized to build multiband bandpass filters (MBPFs). Each individual mode serves as the operating mode for one of the passbands in a well-known coupling topology. However, several difficulties are involved with the classical design method. In this article, we present a novel star-like topology to design MBPFs based on MMRs. Differently from the classical use, in the proposed novel topology, they are so regarded as bandstop resonators and provide multiple controllable transmission zeros. To explain the proposed concept and the implementation method, two bandstop MMRs – a classical dual-mode stub loaded resonator (DSLR) and a new tri-mode dual-stub loaded resonator (TDSR) – are investigated with detailed design formulas and diagrams. Then, a tri-band MBPF with equal individual sub-bands, a quad-band and two quint-band MBPFs with unequal individual sub-bands are synthesized and designed using the proposed bandstop MMRs. Additionally, simulations and experiments are used to verify the efficiency of all prototypes. Good agreements with the theoretical calculations are observed for all the MBPFs.

Compact Wideband Absorptive Filtering Power Divider With a Reused Composite T-Shape Network

This paper presents a compact structure for the filtering power divider (FPD) with wide absorptive bandwidth as well as good isolation between the output ports. A composite T-shape network that consists of a pair of resistors and a central shorted stub is used for realizing good isolation and absorption simultaneously. The isolation resistors that are essential in the FPD can be shared to absorb the signal reflected back to the input port. To enhance the absorption performance, only one synergistic absorptive stub is required and added to the input port. It allows the absorption performance to be independently controllable without affecting the passband response. The dual functions of wideband filtering response and power division are achieved by integrating the power divider and the bandpass filter using a compact three-line coupled structure. A pair of shorted stubs loaded at the ends of coupled-feed lines for outputs can provide controllable passband bandwidth and transmission zeros. To verify the proposed design concept, the multifunctional FPD with the compact structure is fabricated and measured. Good agreements between the measured and simulated results verify the calculated predictions.

A 2.5D low-profile wideband frequency selective structure with high-selectivity performance

In this paper, a low-profile high-selectivity 2.5D FSS based on the dislocation patch structure is proposed and discussed. The dislocation patch structure is used to construct the low-profile transmission line, and a second-order band- pass FSS with a controllable transmission zero is realized by introducing a series LC structure to the dislocation patch structure. The effects of the geometrical parameters on the frequency response of the proposed second-order bandpass FSS are analyzed based on the transmission matrix method and the equivalent circuit simulation. Then, two proposed second-order bandpass FSSs with different transmission zeros are combined and placed crossly to construct two propagation paths, and a high-selectivity third-order FSS is obtained. Finally, the prototype is fabricated and measured to prove the effectiveness of the proposed FSS. The measured results show that the proposed high-selectivity FSS has a wide working bandwidth, proper selective performance, and a thinner profile than other high-selectivity 2D/3D FSSs.

Substrate-Integrated Waveguide Band-Pass Filter and Diplexer With Controllable Transmission Zeros and Wide-Stopband

In this brief, a substrate integrated waveguide (SIW) bandpass filter (BPF) with wide out-of-band rejection is researched and fabricated with the center frequency of 45.8 GHz and 3-dB FBW of 2.18%. Due to the exploitation of electronic excitation, higher order modes mismatch and orthogonal transmission, the simulated and measured out-of-band rejection is better than 20 dB with frequencies up to <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$7.6f_{0}$ </tex-math></inline-formula> and <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$2.4f_{0}$ </tex-math></inline-formula> , respectively. Diplexer with stopband suppression better than 30 dB up to <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$1.87f_{0}$ </tex-math></inline-formula> is proposed based on the theory of the proposed filter. Dual-mode resonator operating with TE301 mode (43.8 GHz) and TE103 mode (45.8 GHz) has been designed to provide the transition of two filter channels. High isolation better than 27 dB over the whole band can be achieved. Transmission zeros (TZs) are generated by spurious resonances under electrical excitation, resulting in high selectively of the passbands. Good agreements between simulations and measurements can be observed.

28-GHz High-Isolation SIW Balanced Diplexer With Highly Controllable Transmission Zeros

This brief proposes a 28-GHz, balanced, and high in-band isolation diplexer based on the substrate-integrated waveguide (SIW) structure. To achieve high isolation and high roll-off rate, a novel coupling scheme by controlling the sign and magnitude of two cross-coupling coefficients is proposed to generate two highly controllable, symmetric or asymmetric transmission zeros (TZs) on both sides of each passband. A three-pole, balanced, and T-junction based diplexer was prototyped with closely spaced channel frequencies at 26.9/28.9 GHz and fractional bandwidths of 3%. The measured differential-mode insertion loss, in-band isolation and common-mode suppression are 3.1/3 dB, greater than 51.2/51.9 dB and greater than 46.4/43.7 dB, respectively. Moreover, in the frequency range of 20–45 GHz, the wideband isolation and common-mode suppression are greater than 37 dB and greater than 34 dB, respectively.

A compact metamaterial SIW diplexer with transmission zeros

ABSTRACT A compact low-loss microstrip diplexer with four controllable transmission zeros (TZs), all less than 41 dB, is presented. The diplexer circuit consists of two coupled gap bandpass filters with a T-junction as a combining circuit. Channels’ filters metalize SIW resonators loaded with metamaterial cells operated at zeroth order mode for compactness and low loss operation. For each channel, a fractional bandwidth of 1.9% is obtained. Also, two TZs at both sides of the resonant frequency are obtained by mixed electric and magnetic coupling between channels’ resonators. Design methodology for filtering response and placing TZs at certain frequencies are discussed in detail. There is a good agreement between simulation and measurement with isolation better than 40 dB. Moreover, the diplexer has a small size of (1.1×1.43 λg 2 ). Lower and higher TZs are located at 4.75 and 5.69 GHz, for the lower channel, and at 5.4 GHz and 6.2 GHz for the higher channel, respectively.

Balanced Dual-Band HTS BPF With Controllable Frequency Ratio and Transmission Zeros Using Mixed Cross-Coupling

In this brief, a fourth-order balanced dual-band high temperature superconducting (HTS) bandpass filter (BPF) is presented based on modified stub-loaded resonators (SLRs). Firstly, the differential mode (DM) and common mode (CM) resonant characteristics of the modified SLRs are analyzed. Under DM operation, two types of mixed cross-coupling topologies are constructed by placing the spiral modified SLRs and their DM equivalent structures in an appropriate way. Then, a dual-band response with controllable center frequencies, bandwidths, and transmission zeros (TZs) is achieved. Under CM operation, an effective CM suppression circuit is proposed for improving the in-band CM suppression level. Finally, for verification, a fourth-order balanced dual-band HTS BPF with center frequencies of 3.494/4.797 GHz and insertion loss of 0.26/0.21 dB is designed and fabricated on MgO substrate with double-sided YBCO thin films. The measured results agree well with the simulated ones, and the BPF shows the attractive features of low insertion loss and good out-of-band rejection.

Compact Low-Loss Half-Mode Substrate Integrated Waveguide Filter With Controllable Transmission Zeros

Two novel planar filters with controllable mixed electromagnetic couplings are developed in this brief for C band operation. They are implemented with the half mode substrate integrated waveguide (HMSIW) technology. Owing to the half mode SIW cavity, both of the filters exhibit a compact size. The size of filter I is <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$0.53\,\,{\boldsymbol{\lambda }}_{\mathbf {0}} \times 0.30 {\boldsymbol{\lambda }}_{\mathbf {0}}$ </tex-math></inline-formula> , while the size of filter II is <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$0.47\,\,{\boldsymbol{\lambda }}_{\mathbf {0}} \times 0.28 {\boldsymbol{\lambda }}_{\mathbf {0}}$ </tex-math></inline-formula> . ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${\boldsymbol{\lambda }}_{\mathbf {0}}$ </tex-math></inline-formula> represents the wavelength in the free space at the center frequency). A wide passband response with a quasi-elliptic characteristic and good out-of-band rejection is realized due to the transmission zeros (TZs) introduced by the etched slot structures on the top metal layer. By modifying the dimensions of the structure, the strength of the electric and magnetic coupling can be independently controlled, and consequently the position of TZs is controllable to achieve desired stopband response with high selectivity. As a validation of the concept, one prototype is fabricated and tested. Excellent agreement is observed between the simulated and measured results.

Wideband High Selectivity Filter Chips With Adjustable Bandwidth Based on IPD Technology

In this brief, two kinds of wideband high selectivity passband filter chips with adjustable bandwidth are proposed. Independent controllable transmission zeros are introduced on both sides of the passband by LC resonators. Two designs are analyzed and calculated by means of odd-even mode analytical method and ABCD matrix to <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${S}$ </tex-math></inline-formula> -parameters matrix method. Finally, integrated passive device (IPD) technology was used to process two versions of broadband and narrowband filters for each design, with a total number of four filter chips. The measured results show that 3-dB fractional bandwidth (FBW) of the first design are 19.3% and 83.6% respectively, which have verified a large degree of freedom in bandwidth control. In addition, the return loss of four chips is better than 17 dB, the optimal insertion loss ranges from 1.31 dB to 2.73 dB, and the stopband rejection is better than 25.2 dB, indicating excellent overall performance.

A novel self‐packaged DBBPF with multiple TZs for 5G sub‐6 GHz applications

AbstractIn this article, we proposed a self‐packaged dual‐band bandpass filter (DBBPF) with high isolation and low insertion loss (IL) for 5G sub‐6 GHz applications. To get high stopband suppression, multiple and controllable transmission zeros (TZs) are introduced. A pair of quarter‐wavelength stepped‐impedance resonators (QSIRs) and half‐wavelength hairpin resonators (HWHR) are introduced to form a cross‐coupled five‐star topology to generate two passbands and multiple TZs analyzed by mixed electromagnetic couplings. A pair of U‐shape resonators are designed on G6 to fully excite the resonators and introduce source/load TZs at the same time. The generation of TZs by separate electric and magnetic coupling paths (SEMCP) is discussed. The DBBPF achieves a low IL of 0.85/1.13 dB with fractional bandwidths (FBW) of 11.0%/6.9% at center frequencies of 3.45 and 4.9 GHz for 5G sub‐6 GHz applications, respectively. The total size is only 0.32 λg × 0.45 λg.

A Triple-Quasi-TEM-Resonance Dielectric Cavity for Bandpass Filter Design

This letter presents a triple-quasi-TEM-resonance dielectric cavity for compact bandpass filter design. The proposed dielectric cavity is silver coated and has three blind holes which form three distinct quasi-TEM mode resonators. The external coupling structure for the resonator is realized by tapping hole. The inter-resonator couplings are realized and controlled by slots on the outer surfaces of the dielectric block. A three-pole filter with two controllable transmission zeros is designed and implemented. The measured results agree well with the simulated results, verifying the proposed triple-resonance dielectric cavity structure and coupling mechanisms.

LTCC Bandpass Filter Chips With Controllable Transmission Zeros and Bandwidths Using Stepped-Impedance Stubs

A novel bandpass filter (BPF) chip using stepped-impedance stubs (SISs) embedded in coupled lines (CLs) based on the low-temperature cofired ceramic (LTCC) technology is proposed in this brief. The controllable bandwidth (BW) is mainly realized by the wide range of variable coupling strength of the broadside CLs, and the controllable transmission zeros (TZs) can be generated by SISs to obtain high selectivity. Furthermore, in order to obtain a general design method for the proposed BPF with different BWs, the analytical (closed-form) process based on the even- and odd- mode analysis method is presented. For verification, a prototype for the proposed BPF operating at 3.5 GHz with the 3-dB fractional bandwidth (FBW) of 32.0% is designed, simulated, fabricated, and measured, respectively. Finally, the measured results that are in good agreement with the simulation show good performance of the proposed circuit.

A Compact, Hybrid SIW Filter With Controllable Transmission Zeros and High Selectivity

A novel, highly selective, and compact filter with controllable transmission zeros (TZs) is proposed in this brief. The hybrid structure of the proposed filter is based on the substrate integrated waveguide (SIW) and microstrip line resonators. The negative magnetic coupling was introduced through a full-wavelength microstrip line resonator, and the additional TZ was added by the cross-coupling of indirectly connected resonators in the traditional box-like topology. Consequently, high selectivity is achieved with TZs located at both sides of the passband. The independent control of the left and right TZs can be realized by controlling the cross-coupling and external coupling. The proposed work achieves good performance, including sharp skirt characteristics, compact size, and low loss. As a validation of the concept and performance, a filter prototype designed following the procedure is fabricated and measured.