Control Strategy For Inverter Research Articles

Research on a New Inverter Control Strategy of Induction Heating Power Supply

To achieve “high voltage, low current” in the induction heating power circuit, enhance the flexibility of component selection in the circuit, and improve the quality of the inverter’s output waveform, a new control strategy of a single-phase NPC three-level inverter with unipolar frequency-doubling SPWM method is proposed. With the series connection of IGBTs in a single-phase NPC three-level inverter, the voltage withstand requirement of IGBT is reduced by half. The middle four IGBTs are controlled using unipolar frequency-doubling SPWM, while the outer four IGBTs are turned on later and turned off earlier to address the neutral point voltage imbalance issue in the inverter. Simulation results show that, compared with the traditional bipolar SPWM-controlled single-phase full-bridge inverter, the DC-side input voltage of the inverter can be double, and the current flowing through the entire circuit can be halved under the same output power using the proposed method.

Model predictive control of multilevel inverter used in a wind energy conversion system application

The rapid growth of renewable energy, particularly wind energy, has significantly contributed to global electricity generation, with global renewable energy capacity reaching an all-time high of 3870 gigawatts (GW) in 2023. However, ensuring high power quality for grid integration remains crucial for wind energy's role as a leading source in the energy transition. This necessitates the development of advanced Wind Energy Conversion Systems (WECS) capable of regulating current, voltage, and frequency to ensure power quality. This work proposes a novel predictive control strategy for multilevel inverters in WECS to achieve a total harmonic distortion (THD) below 5% in the generated electrical power. The proposed predictive control algorithm is presented and implemented in a WECS simulation with a multilevel inverter. The performance of the proposed system is evaluated through simulations using MATLAB/SIMULINK. Our results demonstrate that the predictive control approach outperforms traditional controllers for multilevel inverters in terms of output voltage, harmonic reduction, execution time, and overall WECS control.

Expanded virtual vector-based model forecastable control strategy for three-phase two-level inverters

Abstract A three-phase, two-level inverter based on model forecastable control has good transient performance but poor steady-state performance. Considering the limitation of a limited number of discrete voltage vectors in a two-level inverter topology, this paper proposes a virtual vector model prediction method based on the analysis of a time-stepped forecasting model for a three-phase grid-connected inverter. First, three fixed virtual voltage vectors are constructed in each sector, and the action time of the required fundamental vector is found. Then, the cost function is constructed, and the optimum is selected among the virtual and fundamental voltage vectors in each sector. Finally, a hardware-in-the-loop experiment was carried out based on the PE-Expert4 experimental platform developed by Myway Co., LTD. The results show that the proposed virtual vector model forecastable control strategy can effectively improve the transient and steady-state performance of three-phase two-level inverters.

Fault detection and synchronization control in hybrid DC/AC microgrids using grid-forming inverter DC-link controller

This paper introduces a DC-link fault detection and synchronization control strategy for grid-forming inverters in hybrid DC/AC microgrids, aiming to bolster system stability and reliability. The proposed control scheme seamlessly integrates DC-link fault detection with virtual synchronous generator (VSG) control, facilitating inertia emulation and synchronization without the need for a phase-locked loop (PLL). The DC bus controller is designed to swiftly identify faults triggered by power imbalances, such as load fluctuations or generator integration, and dynamically adjust the power reference for the VSG controller to ensure inertia emulation. The Ziegler-Nichols method is utilized for meticulous tuning of the DC-link controller gains, while the modified swing equation governs VSG inertia and synchronization. MATLAB/Simulink demonstrate the superior performance of the proposed method compared to traditional GFM control strategies. Specifically, the proposed controller improved the frequency nadir to 59.98 Hz compared to 59.75 Hz and showed an enhanced power step response of 7.9×10^5 W compared to 6.9×10^5 W for conventional control method. The proposed GFM control also eliminated the 10×10^6 W switching spike observed with conventional controllers. These findings highlight the potential of this fault-controller approach to advance the reliability and efficiency of hybrid DC/AC microgrids.

Design of voltage and frequency stabilization system for fishing vessel shaft generator based on UPS backup power supply

Abstract A fishing boat shaft generator is a kind of power supply device driven by the main diesel engine, which has the advantage of saving energy compared with a diesel generator and eliminating the need to be equipped with an additional diesel engine, witnessing wide applications in the use of power supply equipment for fishing boats. However, because the shaft generator is mounted on the main diesel engine, the fishing boat encounters bad sea conditions at sea, and the speed of the diesel engine fluctuates, resulting in the instability of the power frequency and voltage sent by the shaft generator, which will endanger the electrical equipment of the fishing vessel in serious cases. In this paper, a design of a voltage and frequency stabilization system for a fishing vessel shaft generator based on a UPS backup power supply was proposed. The system consists of a three-phase shaft generator, inverter, battery, and electrical equipment. The inverter control strategy is introduced, and the battery charge/discharge and DC boost are designed.

A Simplified Model Predictive Current Control Strategy for Six-phase H-bridge Inverters

Background: The double-end H-bridge inverters can realize independent control of the stator voltage in each phase and have flexible advantages of modulation and fault tolerance; thus, they are more suitable for multi-phase fault-tolerant motor drives. However, due to the increase of voltage vectors and the coupling between the electromagnetic and non-electromagnetic quantities, the normal control strategies for traditional three-phase motor drives do not work anymore. Objective: This paper aimed to propose a simplified model predictive current control strategy based on the vector space decomposition (VSD) and the vectors’ gradual simplification for the three-level six-phase H-bridge inverters. Methods: Firstly, the 729 physical variables were decomposed and mapped onto the fundamental αβ subspace, harmonic xy subspace, and the zero-sequence o1o2 subspace based on the VSD. Then, to eliminate the influence of the harmonic and zero-sequence components on the control performance and make an easy digital implementation, vectors’ simplification has been proposed based on the in-depth analysis of the relationship between the voltage vectors mapped onto different subspaces and vectors’ stratification. With the simplification method, the number of voltage vectors was simplified from 729 to 12, and then the selected voltage vectors were used in the rolling optimization of the model predictive current control (MPCC) to choose the optimal one. Finally, sufficient experiments were carried out including static and dynamic conditions, different modulation index and power factor, etc., to verify the feasibility of the proposed strategy. Results: The simulation and experimental results show that with the simplified MPCC strategy, both the static and dynamic performances are relatively good, and the THDs of the phase current under different modulations and power factors are relatively low. Conclusion: The proposed MPCC algorithm for the three-level six-phase H-bridge inverters has shown obvious improvement in solving the control problems of multi-vectors and complex redundancy issues.

Research on Inverter Control Strategy Based on FPGA

Abstract This study adopts a composite repetitive controller strategy in a three-phase four-wire circuit, combining proportional resonance and repetitive control, which effectively suppresses harmonics and improves system performance. At higher switching frequencies, FPGA is used to achieve efficient control to ensure system stability and performance. This research provides new ideas for improving the performance of on-board inverters, especially in terms of high-speed control, nonlinear load and harmonic processing. SiC devices and composite control strategies provide more sustainable solutions for future rail transit systems.

A novel RMPC strategy for three-phase inverters operating in grid-connected and standalone modes

One of the main features of microgrids is the capability of operating in both grid-connected (GC) and standalone (SA) modes. This paper presents a novel dual mode robust model predictive control (RMPC) strategy for a three-phase inverter with an LCL filter in both GC and SA operating modes under the filter’s parameter uncertainty. At first, a disturbance observer gain is obtained by solving a linear matrix inequality (LMI), which is determined to preserve the stability of the algorithm. The designed disturbance observer takes into account the polytopic uncertainty of system parameters. A performance index with two weighting matrices is then defined and solved in an infinite horizon by turning it into an optimization problem under LMI constraints. The performance of the control strategy highly depends on the weighting matrices. Hence, an optimization algorithm is formulated to ascertain the best matrices values for both GC and SA operation modes. Given the nonlinearity issue, particle swarm optimization (PSO) is employed to derive the optimal weighting matrices offline. To evaluate the proposed control strategy’s effectiveness, simulations and experiments are performed under several scenarios in both GC and SA operating modes. The results reveal the proposed control strategy’s powerfulness compared to other techniques in the presence of grid voltage and load current disturbances for both inverter operating modes.

Adaptive low voltage crossing strategy for symmetrical faults of networked inverters

Abstract Due to the inability of grid-following control methods to compensate for the comprehensive reduction in system inertia, strength, and short-circuit capacity caused by the decreased proportion of synchronous machines, the grid exhibits insufficient resilience to disturbances, leading to severe stability risks in terms of rotor angle, frequency, and voltage. Grid-forming inverters have emerged to address this issue. During symmetrical faults, the low-voltage ride-through of grid-forming inverters often involves freezing the reactive power loop, resulting in a direct output of higher voltage and reactive current. However, an increase in reactive power command leads to a sharp rise in the internal potential magnitude of grid-forming inverters. Upon clearance of the grid fault, the excessively high internal potential may cause a rapid, short-term increase in terminal voltage, potentially resulting in overvoltage, which is detrimental to the operation of grid-connected equipment. In response to this issue, this paper proposes an adaptive low-voltage ride-through control strategy for grid-forming inverters under symmetrical faults controlled by a virtual synchronous machine control method. Initially, a virtual synchronous machine control model is established. Limiting current is achieved through the construction of a fixed virtual impedance loop. The issues associated with fixed virtual impedance current limiting are analyzed, leading to the proposal of an adaptive virtual impedance control strategy. Finally, the feasibility of the proposed method is verified through simulation experiments.

Multi-DG qZSI based grid tied inverters

The increasing adoption of distributed generation (DG) systems, driven by their numerous advantages, has led to a growing utilization of hybrid systems. Multilevel converters have emerged as essential components in power electronics applications, offering benefits such as harmonic reduction. However, designing effective control strategies for multilevel inverters presents challenges. This paper proposes a multi-DG quasi-Z-Source Inverter (qZSI) designed with a cascaded H-bridge controller. The incorporation of qZSI in the system enhances reliability and component safety while enabling the implementation of additional shoot-through control. This feature facilitates the balancing of inequalities arising from the two DG sources, thereby improving disturbance rejection. Furthermore, a current control scheme is implemented on the AC side to seamlessly feed active power into the grid without introducing distortions in current injection. Overall, the proposed system addresses key challenges in multilevel inverter design and offers a promising solution for efficient and reliable grid integration of DG systems. This work is thus useful in variety of applications, including electric vehicles and environment sustainability.

Adaptive reactive power control strategy for grid-forming inverter under symmetrical fault

Abstract Due to the inability of the grid-type control method to compensate for the comprehensive reduction in system inertia, strength, and short-circuit capacity caused by the proportional decrease of synchronous machines, the power grid exhibits insufficient resistance to disturbances, leading to severe stability risks in terms of rotor angle, frequency, and voltage. In response to these challenges, grid-forming inverters have emerged. Under symmetrical faults, the low-voltage ride-through of grid-forming inverters is often accompanied by a frozen reactive power environment, resulting in a direct output of increased voltage and reactive current. However, an elevated reactive power command can cause a sharp increase in the potential amplitude within grid-forming inverters. After the grid fault is cleared, the excessively high internal potential can cause a short-term and rapid increase in terminal voltage, potentially leading to overvoltage, which is detrimental to the operation of grid-connected devices. To address this issue, this paper first employs a grid-forming inverter controlled by a virtual synchronous machine control method. Using the grid positive-sequence voltage as a reference value, it identifies whether a voltage drop fault has occurred. Based on this, an adaptive reactive power control strategy is proposed, which can promptly achieve the same effect as the frozen reactive power environment during faults, while also promptly restoring the reactive power environment after fault clearance, thereby avoiding overvoltage issues. The feasibility of the proposed method is verified through the establishment of a simulation system.

Design and Implementation of Model Parameter Independent Robust Current Control Scheme of Three-Phase Inverter - A Neural Network-Based Classification Approach

Design and Implementation of Model Parameter Independent Robust Current Control Scheme of Three-Phase Inverter - A Neural Network-Based Classification Approach

A Stabilization Control Strategy for Wind Energy Storage Microgrid Based on Improved Virtual Synchronous Generator

A Stabilization Control Strategy for Wind Energy Storage Microgrid Based on Improved Virtual Synchronous Generator

LADRC-based grid-connected control strategy for single-phase LCL-type inverters.

To ensure that grid-connected currents are of high quality, it is crucial to optimize the dynamic performance of grid-connected inverters and their control. This study suggests using a combination of reduced-order linear active disturbance rejection control (LADRC) and a Proportional-Integral (PI) controller. By applying this control strategy to a single-phase photovoltaic grid-connected system, the system's ability to suppress grid harmonics is significantly improved. The validity and effectiveness of this control approach have been confirmed through simulations and experiments. The results show that the LADRC-based control system is robust and capable of rejecting disturbances, resulting in a significant reduction in the Total Harmonic Distortion (THD) of grid-connected currents. Comparative analysis with traditional control methods demonstrates the superior performance of the proposed approach.

IIR filter-based compensator with modified feedback repetitive control scheme of voltage source inverter for nonlinear load applications

IIR filter-based compensator with modified feedback repetitive control scheme of voltage source inverter for nonlinear load applications

Robust Control Based on Adaptative Fuzzy Control of Double-Star Permanent Synchronous Motor Supplied by PWM Inverters for Electric Propulsion of Ships

This study presents the development of an adaptive fuzzy control strategy for double-star PMSM-PWM inverters used in ship electrical propulsion. The approach addresses the current and speed tracking challenges of double-star permanent magnet synchronous motors (DSPMSMs) in the presence of parametric uncertainties. Initially, a modeling technique employing a matrix transformation method is introduced, generating decoupled and independent star windings to eliminate inductive couplings, while maintaining model consistency and torque control. The precise DSPMSM model serves as the foundation for an unknown nonlinear backstepping controller, approximated directly using an adaptive fuzzy controller. Through the Lyapunov direct method, system stability is demonstrated. All signals in the closed-loop system are ensured to be uniformly ultimately bounded (UUB). The proposed control system aims for low tracking errors, while also mitigating the impact of parametric uncertainties. The effectiveness of the adaptive fuzzy nonlinear control system is validated through tests conducted in hardware-in-the-loop (HIL) simulations, utilizing the OPAL-RT platform, OP4510.

LVRT Control Strategy for Three-Phase CHB PV Inverter Based on Coordinated Compensation of Fundamental-Frequency Adaptive Zero-Sequence Voltage and its Odd Harmonics

LVRT Control Strategy for Three-Phase CHB PV Inverter Based on Coordinated Compensation of Fundamental-Frequency Adaptive Zero-Sequence Voltage and its Odd Harmonics

A Virtual Resistance Optimization Method Based on Hybrid Index in Low-voltage Microgrid

Introduction: The introduction of virtual resistance can effectively suppress the circulating current between micro-sources and improve power allocation in low-voltage microgrid, but it also causes the voltage deviation of micro-sources’ inverters. An optimization method of virtual resistance based on hybrid index is proposed in order to suppress circulating current and improve voltage deviation at the same time in this paper. The gradient descent method is used to design the virtual resistance optimization process, aiming at the optimization of hybrid index composed of circulating current and voltage deviation. The constraints are deduced with power quality requirements, capacity limitation and static stability, and then virtual resistance values are optimized. The effects of switching load and micro-source on the optimization results are analyzed through the simulation of low-voltage microgrid, and the simulation results show that the virtual resistance optimization method can significantly suppress circulating current while improving power quality. When distributed generators are connected to utility grid through inverters and feeders, differences in feeder parameters and inverter control strategies easily cause circulating current and uneven power distribution among micro-sources. The introduction of virtual resistance can effectively suppress the circulating current between micro-sources and improve power allocation in low-voltage microgrids, but it also causes the voltage deviation of micro-sources’ inverters. An optimization method of virtual resistance based on hybrid index is proposed in order to suppress circulating current and improve voltage deviation. Methods: The gradient descent method is used to design the virtual resistance optimization process, aiming at the optimization of hybrid index composed of circulating current and voltage deviation. The constraints are deduced with power quality requirements, capacity limitation and static stability, and then virtual resistance values are optimized. Results: In the simulation scenario of two micro-sources and three micro-sources, the virtual resistance obtained by the method proposed in this paper has more obvious improvement on the system operation index, and is not affected by the load type. Conclusion: The method of optimizing virtual resistance based on the hybrid index can achieve the effect of restraining circulating current and improving power sharing degree on the premise of guaranteeing power quality and satisfying system stability. The optimization of virtual resistance is affected by the number of feeders. It is necessary to re-optimize the virtual resistance after changing the number of feeders, but the process of switching micro-source and adjusting load does not affect the optimized resistance value.

An Effective Control Strategy for Single-Phase Single-Stage PV Grid-Tied Inverter Under Abnormal Grid Conditions

An Effective Control Strategy for Single-Phase Single-Stage PV Grid-Tied Inverter Under Abnormal Grid Conditions

Impedance remodeling control strategy of grid-connected inverter with inertia-damping phase-locked loop under extremely weak grid

The operation of the grid-connected inverter (GCI) in weak grid conditions presents a risk of instability due to the presence of high grid impedance and the negative impedance effect of the phase-locked loop (PLL). In response to this issue, this paper introduces an impedance remodeling control strategy for the GCI utilizing the inertia-damping phase-locked loop (ID-PLL). Firstly, the proposed ID-PLL exhibits certain inertia and damping properties in comparison to the traditional PLL (T-PLL), resulting in an enhanced phase margin of the GCI system's equivalent output impedance. Consequently, the adaptation range of the grid impedance increases from 12mH (SCR = 3.00) to 24mH (SCR = 1.37). Next, from the perspective of impedance analysis, this study remodels the PLL impedance and inverter control loop impedance, further improving the amplitude and phase margin of the system's output impedance. As a result, the adaptation range of the grid impedance extends to 33mH (SCR = 1.00), and the transition of grid-connected currents becomes smooth and free of overshoot. Finally, the effectiveness of the proposed control strategy is validated through theoretical analysis and experimental verification.