Conduction Mode Boost Power Factor Research Articles

Maximum Efficiency Average Current Controller Based on a Comprehensive Charge Rate Model for DCM Boost PFC Converter

This article investigates modeling and control approaches to optimize the efficiency and power factor for discontinuous conduction mode boost power factor correction converters. First, with detailed consideration of parasitics and GaN HEMT transients, the input and output charges of the converter are exactly derived, where the rate forms the comprehensive charge rate (CCR) model. Second, based on the CCR model, the overall efficiency is derived. Since the overall efficiency is only related to the input voltage, output voltage, and switching on -time, an optimal on -time is calculated to achieve the maximum efficiency. Furthermore, with the optimal on -time, a maximum efficiency average current (MEAC) controller is proposed to regulate the input current while maintaining the maximum efficiency. With the predefined optimal on -time, a switching cycle modulation method is adopted to regulate the input current as sinusoid, which improves the power factor to unity. Finally, effectiveness of the MEAC control strategy is verified by simulations and experiments. Compared with conventional constant on -time control, it achieves an optimized efficiency and power factor over a large operation range.

Heteromagnetic Swinging Inductor and Its Application for Power Factor Correction Converters

A variable inductor concept based on a magnetic structure consisting of composite of magnetic materials is introduced to meet the designed inductance function of current. A design of the inductor, termed heteromagnetic swinging inductor (HMSI), was fabricated using a toroid core with a gap that was filled by a custom-developed low-permeability magnetic powder + polymer material. Having the gap filled with the magnetic material allowed for greater flexibility in L–I design with added benefit of low fringe field. The analytical model of HMSI was derived and verified by simulation. And the step-by-step design of arbitrary L–I curve HMSI was posted. We applied this swinging inductor to a critical conduction mode boost power factor correction converter to reduce its switching frequency variation range. First, the required L–I curve of the HMSI needed for narrow range of switching frequency was calculated. Then, the HMSI core structure consisting of two magnetic materials was designed. Finally, a prototype of the HMSI was fabricated and tested. Experimental result showed that for a 110-Vrms input, the converter with the HMSI had a switching frequency variation factor, defined as Δ f / f min, six times less than that of the converter using a linear inductor.

Quasi-Fixed Switching Frequency Control of CRM Boost PFC Converter Based on Variable Inductor in Wide Input Voltage Range

With traditional constant on-time control, the switching frequency variation range of critical conduction mode boost power factor correction converter is large during a half line cycle, not to mention the wide range of input voltage's rms value. For this issue, this article puts forward a quasi-fixed switching frequency control, which combines the variable on-time and variable inductor technology together. Furthermore, a lower output voltage ripple and a higher efficiency are obtained. In spite of the power factor decrease, the input current harmonics still satisfy the IEC61000-3-2 Class D limits. The detailed theoretical analysis and experimental results are presented in this article.

A Current Reshaping Strategy to Reduce Parasitics-Induced Current Distortion in Discontinuous Conduction Mode Boost Power Factor Correction Converter

This article reveals parasitics-induced current distortion (PCD) effect in discontinuous conduction mode boost power factor (PF) correction (PFC) converter. With consideration of parasitics, accurate inductor current is derived through total differential functions of line voltage, output voltage and duty cycle. Furthermore, the proposed current model is used to analyze PFC converter under conventional sensorless average current mode (SACM) control, which is achieved by a variable duty cycle. It is found that parasitics have considerable influence to the input current, and PCD leads to a degraded PF. In order to solve this issue, a current reshaping strategy is proposed to reduce the PCD phenomenon. Based on the damped current equations, a compensation gain is derived to reshape the input current, which reduces the current damping and distortion caused by parasitics. Both the PCD phenomenon and the current reshaping strategy are verified by simulations and experiments.

Optimal Switching Frequency Variation Range Control for Critical Conduction Mode Boost Power Factor Correction Converter

Critical conduction mode boost power factor (PF) correction converter is widely used in low-to-medium power applications for its advantages of high PF, zero-current turn-on of the switch, and no reverse recovery in diode. Nevertheless, the switching frequency varies continually with the input voltage phase angle with traditional constant on-time control. This makes the electromagnetic interference (EMI) spectra display great differences and complicates the design of EMI filter. An optimal switching frequency variation range control strategy is proposed in this article. The optimal harmonics amounts for the lowest switching frequency variation range without and with a limited PF are both figured out. In addition, a lower output voltage ripple is obtained. A prototype has been built and tested in the lab to demonstrate the validity of the theoretical analysis.

Optimum Boundary Inductance Control Concerning Limited PF for a DCM Boost PFC Converter

The discontinuous conduction mode boost power factor correction converter features zero-current turn- on for the switch, no reverse recovery in diode, and constant frequency operation. With traditional constant duty ratio control, the power transfer in each switching cycle exhibits great difference during a half-line cycle. Consequently, the peak and root mean square values of the inductor current are large, the same goes for the switch and diode. This increases not only the current stress of the power components but also the conduction and switching turn- off loss, and lowers the efficiency of the converter. Introducing third and fifth harmonics into the input current and varying the duty cycle correspondingly can reduce the aforementioned power transfer difference, and provide huge space for the increment of boundary inductance as well. An optimum boundary inductance control concerning limited power factor (PF) is proposed in this paper. For the maximum boundary inductance of the converter within wide input voltage range, the optimum harmonics amounts are analyzed and figured out. The proposed method brings about efficiency improvement, output voltage ripple reduction, and PF increase as well, especially at high input voltages. A prototype has been built and the experimental results are presented to show the validity of the scheme.

A Digital Phase Leading Filter Current Compensation (PLFCC) Technique for CCM Boost PFC Converter to Improve PF in High Line Voltage and Light Load Conditions

This paper proposes a digital phase leading filter current compensation (PLFCC) technique for a continuous conduction mode boost power factor correction to improve PF in high line voltage and light load conditions. The proposed technique provides a corrected average inductor current reference and utilizes an enhanced duty ratio feed-forward technique which can cancel the adverse effect of the phase leading currents caused by filter capacitors. Moreover, the proposed PLFCC technique also provides the switching dead-zone in nature so the switching loss can be reduced. Therefore, the proposed PLFCC can significantly improve power quality and can achieve a high efficiency in high line voltage and light load conditions. The principle and analysis of the proposed PLFCC are presented, and performance and feasibility are verified by experimental results from the universal input (90–260 $V_{\rm AC}$ ) and 750 W–400 V output laboratory prototype.

Control method for improving the response of single‐phase continuous conduction mode boost power factor correction converter

Continuous conduction mode power factor correction AC–DC converters are widely employed as the front stage in power supplies with medium or high output power. The second-order reactive input power in single-phase systems causes second-order ripple in the DC-link voltage. The speed of voltage regulation is thus limited by the second-order frequency in seeking to achieve low distorted input current. This study presents a fast second-order voltage estimation method, wherein an integrator is used for the estimation of second-order voltage ripple to obtain rapid voltage feedback without ripple and thereby cope with the limitations imposed by the second-order frequency. This approach greatly expands the bandwidth of the voltage control loop beyond the second-order frequency while reducing the total harmonic distortion associated with the input current. This also makes it possible to reduce the DC capacitance to reduce costs. The authors opted for full digital control using a TI F28335 DSP IC, in conjunction with feedback plus feedforward control to facilitate the design of the current loop. A feedback current corrector is used to reduce distortion associated with the input current over a wide load range. The effectiveness of the proposed control method was confirmed with some simulation and experimental results.

Enhanced Variable On-time Control of Critical Conduction Mode Boost Power Factor Correction Converters

Critical conduction mode boost power factor correction converters operating at the boundary of continuous conduction mode and discontinuous conduction mode have been widely used for power applications lower than 300W. This paper proposes an enhanced variable on-time control method for the critical conduction mode boost PFC converter to improve the total harmonic distortion characteristic. The inductor current, which varies according to the input voltage, is analyzed in detail and the optimal on-time is obtained to minimize the total harmonic distortion with a digital controller using a TMS320F28335. The switch on-time varies according to the input voltage based on the computed optimal on-time. The performance of the proposed control method is verified by a 100W PFC converter. It is shown that the optimized on-time reduces the total harmonic distortion about 52% (from 10.48% to 5.5%) at 220V when compared to the variable on-time control method.

A feedforward compensation design in critical conduction mode boost power factor correction for low-power low totalharmonic distortion

For low-power low total harmonic distortion (THD), based on the CSMC 0.5 μm BCD process, a novel boost power factor correction (PFC) converter in critical conduction mode is discussed and analyzed. Feedforward compensation design is introduced in order to increase the PWM duty cycle and supply more conversion energy near the input voltage zero-crossing points, thus regulating the inductor current of the PFC converter and compensating the system loop gain change with ac line voltage. Both theoretical and practical results reveal that the proposed PFC converter with feedforward compensation cell has better power factor and THD performance, and is suitable for low-power low THD design applications. The experimental THD of the boost PFC converter is 4.5%, the start-up current is 54 μA, the stable operating current is 3.85 mA, the power factor is 0.998 and the efficiency is 95.2%.