Electric Current Research Articles

Experimental and numerical analysis of 3D end effects in Naval Magnetohydrodynamic propulsion motors

This study explores the impact of end electric current on the performance of a marine magnetohydrodynamic (MHD) propulsion motor or thruster using a comprehensive 3D numerical simulation. The investigation focuses on various operating parameters, such as electromagnetic and drag forces, efficiency, losses, current, and different pressure components. To validate the numerical findings, a scaled-down experimental setup is utilised. The results demonstrate that certain operating parameters of MHD motors are not affected by the three-dimensional characteristics of their channels. These parameters, including fluid velocity, can be accurately calculated using the analytical model based on the effective electric current of the motor. Conversely, other operating parameters of MHD motors are significantly influenced by the end effects in their channels. For example, the overall efficiency, which depends on the total electric current of the motor, should be calculated using a more precise simulation method.

Non-Invasive Brain Sensing Technologies for Modulation of Neurological Disorders

The non-invasive brain sensing modulation technology field is experiencing rapid development, with new techniques constantly emerging. This study delves into the field of non-invasive brain neuromodulation, a safer and potentially effective approach for treating a spectrum of neurological and psychiatric disorders. Unlike traditional deep brain stimulation (DBS) surgery, non-invasive techniques employ ultrasound, electrical currents, and electromagnetic field stimulation to stimulate the brain from outside the skull, thereby eliminating surgery risks and enhancing patient comfort. This study explores the mechanisms of various modalities, including transcranial direct current stimulation (tDCS) and transcranial magnetic stimulation (TMS), highlighting their potential to address chronic pain, anxiety, Parkinson’s disease, and depression. We also probe into the concept of closed-loop neuromodulation, which personalizes stimulation based on real-time brain activity. While we acknowledge the limitations of current technologies, our study concludes by proposing future research avenues to advance this rapidly evolving field with its immense potential to revolutionize neurological and psychiatric care and lay the foundation for the continuing advancement of innovative non-invasive brain sensing technologies.

An Insight into the Impact of Nano CuCo2O4 Doping on the Optical and Dielectric Performance of PMMA/Carbon Nanoparticles

Abstract The blends obtained were subjected to characterization using SEM (scanning electron microscopy) and XRD (x-ray diffraction). By utilizing diffuse reflectance measurements, an extensive investigation into different optical properties was carried out, covering energy band gap, refractive index, extinction coefficient, dielectric constant, conductivity, as well as nonlinear optical properties. After the incorporation of CNPs /CuCo2O4 in the polymer, the transmittance of the PMMA experienced a decline from 92% to 42%, while the absorbance, reflectance and refractive index exhibited an increase. As the blend incorporated CuCo2O4, a continuous reduction in both direct and indirect optical band gap energies of PMMA (4.94 and 4.69 eV) was observed attaining 4.4 and 4.37 eV for 2.5 wt.% CuCo2O4, respectively. It is noteworthy that the initially inadequate optical conductivity of PMMA exhibited a significant improvement, leading to enhanced linear and nonlinear optical parameters with increasing CuCo2O4 doping levels. Analysis of fluorescence spectra (FL) revealed a decrease in FL intensity and a shift in maximum position as the CuCo2O4 content (x) increased, resulting in the generation of the CIE chromaticity diagram. Dielectric measurements provided insights into the impact of CuCo2O4 content on alternating current (AC) conductivity, energy density, dielectric properties, and electric modulus across all blends.

Interfacial Electron Beam Lithography Converts an Insulating Organic Monolayer to a Patterned Single-Layer Conductor with Puzzling Charge Transport Performance.

The direct generation of conducting paths within an insulating surface represents a conceptually unexplored approach to single-layer electrical conduction that opens vistas for exciting research and applications fundamentally different from those based on specific layered materials. Herein we report surface channels with single-layer -COOH functionality patterned on insulating n-octadecyltrichlorosilane monolayers on silicon that exhibit unusual ionic-electronic conduction when equipped with ion-releasing silver electrodes. The strong dependence of charge transport in such channels on their lateral dimensions (nanosize, macro-size), the type (p, n) and resistivity (doping level) of the underlying silicon substrate, the nature of the insulating spacer layer between the conducting channel and the silicon surface, and the postpatterning chemical manipulation of channel's -COOH functionality allows designing channels with variable resistivities, ranging from that of a practical insulator to some unexpectedly low values. The unusually low resistivities displayed by channels with nanometric widths and micrometer-millimeter lengths are attributed primarily to enhanced electronic transport within ultrathin nanowire-like silver metal films formed along their conductive paths. Function-structure correlations derived from a comprehensive analysis of electrical, atomic force microscopy, and Fourier transform infrared spectral data suggest an unconventional mode of conduction in these channels, which has yet to be elucidated, apparently involving coupled ionic-electronic transport mediated and enhanced by interfacial electrical interactions with charge carriers located outside the conducting channel and separated from those carrying the measured current. These intriguing findings hint at effects akin to Coulomb pairing in the proposed mechanisms of excitonic superconductivity in interfacial nanosystems structurally related to the present metalized surface channels.

Impact of preanaesthetic electrocardiogram on decision making and modification of anaesthetic protocols in dogs.

This retrospective observational study explored the impact of preanaesthetic electrocardiogram (ECG) assessment on preoperative echocardiography requests and modifications to a standardised anaesthetic protocol in healthy dogs. A total of 228 healthy dogs with no previously diagnosed heart disease that underwent general anaesthesia at Complutense Veterinary Teaching Hospital from December 2017 to June 2018 were included. Preanaesthetic ECGs were assessed for abnormalities, and the findings were documented. The number of dogs requiring echocardiography, based on ECG findings, and the echocardiography results were recorded. All anaesthesia-related decisions were documented. Overall, 72 dogs (31.6%) exhibited ECG abnormalities. Echocardiography was requested for five dogs (2.2%). The anaesthetic protocol was changed in 11 dogs (15.3% of those with ECG abnormalities). P wave disturbances, ventricular premature complexes and impulse conduction issues were abnormalities that prompted echocardiography. Bradycardia and electrical impulse conduction abnormalities influenced protocol modifications. The limited sample size meant that it was not possible to investigate potentialcorrelations between demographics and ECG alterations. Preanaesthetic ECG screening was useful forpromoting echocardiography and influencing anaesthesia plans in a subset of dogs. Despite this, further assessment of the impact of routine use of non-targeted preoperative ECG on anaesthesia-related outcomes is warranted.

The dental management of patients with Brugada syndrome: A case series

AbstractBrugada syndrome is an inherited cardiovascular disorder, which can affect the rhythm of the heart. Dental treatment can often present as an obstacle for patients with Brugada syndrome as the use of local anaesthetic can have adverse effects on the electrical conduction system of the heart.AimThe aim of this series is to discuss the aetiopathogenesis, presentation and management of Brugada syndrome and its relevance to dentistry and the dental team.MethodsThe authors present a series of three Brugada syndrome patients who underwent dental intervention in a hospital setting.Results and ConclusionThe series highlighted the importance of multidisciplinary care for patients with Brugada syndrome. Liaising with other teams, such as cariologists and GMPs, allows a patient centred approach and better understanding of patient management.

Experimental Investigations of the AC-Conductivity in NaTaO3 Ceramic Materials Doped with Cu and Al Metal Ions

Two ceramic samples of sodium tantalate (NaTaO3), doped with metal ions of copper (Cu; sample S1) or aluminum (Al; sample S2), were obtained by the sol-gel method. Complex impedance measurements in the frequency range (200 Hz–2 MHz) and at temperatures between 30 °C and 90 °C allowed identification of a transition temperature from semiconductor-type behavior to conductor-type behavior for each sample (52 °C for sample S1 and 54 °C for sample S2). In the temperature range with semiconductor behavior, the activation energy of each sample was determined. Based on the Mott’s variable-range hopping (VRH) model, the density of localized states at the Fermi level, N(EF), the hopping distance (R) and the hopping energy (W) were determined, for the first time, on NaTaO3 samples doped with Cu or Al metal ions. The increase in N(EF) of sample S2 compared to N(EF) of sample S1 was explained by the decrease in the hopping distance of charge carriers in sample S2 compared to that in sample S1. Additionally, using the correlated barrier hopping (CBH) model, the energy band gap (Wm) and the hopping (crossover) frequency (ωh) at various temperatures were determined. Knowledge of these electrical properties is very important for explaining the electrical conduction mechanisms in metal ion-doped compounds, with perovskite structure being of interest for the use of these materials in the conversion of thermoelectric energy, photocatalytic applications, electronics or other applications.

Advances in clinical research on ultrasound-guided radiofrequency ablation for papillary thyroid microcarcinoma

Ultrasound-guided radiofrequency ablation (RFA) emerges as a minimally invasive strategy for papillary thyroid microcarcinoma (PTMC), offering advantages over traditional surgical approaches. RFA employs high-frequency electric currents under precise ultrasound guidance to ablate cancerous tissue. Clinical trials consistently demonstrate RFA’s efficacy in tumor control and patient-reported outcomes. However, long-term studies are essential to validate its durability and monitor for potential complications. Collaborative efforts among various medical disciplines ensure procedural accuracy and comprehensive postoperative care. Technological innovations, such as enhanced ultrasound imaging and temperature control, promise to refine RFA’s precision and effectiveness. Nevertheless, challenges persist, including the need for standardized protocols and comparative studies with traditional treatments. Future research should focus on long-term outcomes, patient selection criteria, and optimization of procedural techniques to solidify RFA’s role in PTMC management. RFA presents a promising avenue for PTMC treatment, warranting further investigation and refinement in clinical practice.

Tailoring the physicochemical and dielectric properties of natural polymer using graphene nanoplatelet as filler

AbstractBio‐based flexible dielectric substrates have gained tremendous attention for their potential to reduce environmental risks from nonbiodegradable electronic waste. The present study demonstrates the fabrication of facile, nontoxic, and biodegradable chitosan‐based flexible dielectric substrate using graphene nanoplatelet (GNP) as a nanofiller. The detailed impact of different concentrations of GNP (1, 2, and 3 wt%) into the chitosan (CS) matrix was studied on physicochemical, morphological, mechanical, electrical, and thermal properties. The fabricated CS/GNP composites showed improved mechanical strength, thermal stability, and electrical properties compared with unmodified CS film. The composites exhibited excellent thermal stability (200°C) with a promising biodegradation rate (within 6 days). The mechanical strength of the unmodified CS film was increased unequivocally with 2 wt% GNP loading with tensile strength of 23.56 Mpa. Furthermore, the current–voltage (I–V) characteristic curves for CS/GNP (2%) and CS/GNP (3%) showed similar current conduction and ohmic behavior in flat, bending, and flat‐after‐bending modes. The dielectric measurements revealed that the CS/GNP composite with 2 wt% filler exhibited optimal performance having permittivity (έ) of 32.71 (at 102 Hz) with low dielectric loss of 0.04 (at 106 Hz). These results suggest that the dielectric films offer strong prospects as an eco‐friendly alternative for various applications.Highlights Biodegradable chitosan‐based flexible dielectric films were prepared. Films were made using a simple solvent casting method with 1–3 wt% GNP filler. Optimum physicochemical and electrical properties were seen at 2 wt% GNP. CS/GNP (2%) film exhibited ohmic behavior in both flat and bending modes. Excellent dielectric properties were achieved at 2 wt% GNP filler.

Harmonic power flow under non-sinusoidal conditions

This article aims to analyze the electric field and the flow of electromagnetic energy in power cables with copper and aluminum cores, without considering the implicit physics of the coating that surrounds the conductor, which is generally composed of XLPE. Computational simulations were carried out with two models of alternating electrical current (AC) intensities, with a frequency of 60 HZ, electrical voltage of 1 kV, in a transient regime, with a phase difference of 120° and considering the lengths of the cables at a value of L = 30 m. Applying a Fourier series expansion to a sinusoidal electric current and expanding to the third term of the series, resulting in a new formulation of the electric current that was called modified electric current. The peculiarity of this research lies in the fact that, through the Fourier series expansion of conventional alternating current, a transformation to a modified current was observed, presenting behavior analogous to that of a Rectifying Diode. The improvements provided by this method include increased efficiency in the transmission of electrical energy, reduction of voltage drops, reduction of losses associated with the Joule-Lenz effect and extension of the useful life of the cable. The results demonstrated that, by modifying the electric current, the electric fields and Poynting vectors were calculated and approached the solutions of Maxwell's equation for conventional electric current, in both types of power cables. In addition, this approach has been observed to be particularly effective for power cables with a length of 30 m, and using the modified current in Maxwell's equations to compare the electric and Poynting fields with those calculated using conventional electric current. Therefore, the results obtained are satisfactory for both power cables.

Electrical transport and dielectric relaxation mechanism in Zn0.5Cd0.5Fe2O4 spinel ferrite: A temperature- and frequency-dependent complex impedance study

In the present study, the frequency-dependent dielectric relaxation and electrical conduction mechanisms in sol-gel-derived Zn0.5Cd0.5Fe2O4 (ZCFO) spinel ferrite were studied in the temperature range of 343–438 K. The formation of the ZCFO spinel ferrite phase with space group Fd3m was confirmed by X-ray diffraction analysis. The dielectric relaxation and electrical conduction mechanisms were studied using complex impedance spectroscopy (CIS). In the Nyquist plots, depressed semicircles were fitted with an equivalent circuit model with configuration (RGBQGB) (RGQG), signifying the contributions from grain boundaries and grains to the charge transport mechanism in the sample. The frequency-dependent AC conductivity was found to follow Jonscher's power law, and the frequency exponent term depicted the overlapping large polaron hopping (OLPH) model as the dominant transport mechanism. The activation energies for conductivity, electric modulus and impedance were calculated to identify the nature of the charge carriers governing the relaxation and conduction mechanisms in the prepared sample. Complex modulus studies confirmed the non-Debye type of dielectric relaxation, whereas tangent loss and dielectric constant analyses confirmed the thermally activated hopping mechanism of charge carriers in Zn0.5Cd0.5Fe2O4 spinel ferrite.

Hydroxyapatite coating of TiNi shape memory alloy via Electrophoretic Deposition (EPD)

ABSTRACT In this study, hydroxyl apatite (HA) as a bio-ceramic is coated on the TiNi shape memory. In this approach, Tri-ethanolamine and butanol were used as suspensions. To set up Electrophoretic Deposition (EPD) process, voltages of 20, 30 and 40 volts were applied on the cathode for 1-5 minutes. The sintering process was done in the Ar atmosphere for two hours at 800°C. SEM and XRD were used to investigate surface morphologies and phases. Obtained results showed that higher electrical currents led to generation of thicker coatings registering 105% and 12.3% improvement for weight and thickness after 6 minutes, respectively. Moreover, Transformation of HA to other calcium phosphate phases doesn’t happen at a sintering temperature of 800°C. Moreover, a uniform, homogeneous and crackles coating can be reached in the voltage of 30 volts at low sintering temperatures. This process can be utilized an alternative technique for bioactive coatings.

Efficient Modeling of Single Event Transient Effect with Limited Peak Current: Implications for Logic Circuits

The problem that the conventional double-exponential transient current model (DE model) can overdrive the circuit, which leads to the overestimation of the soft error rate of the logic cell, is solved. Our work uses a new and accurate model for predicting the soft error rate that brings the soft error rate closer to the actual. The piecewise double-exponential transient current model (PDE model) is chosen, and the accuracy of the model is reflected using the Layout Awareness Single Event Multi Transients Soft Error Rate Calculation tool (LA-SEMT-SER tool). The model can characterize transient current pulses piecewise and limit the peak current magnitude to not exceed the conduction current. TCAD models are constructed from 28 nm process library and cell layouts. The transfer characteristic curves of devices are calibrated, and functional timing verification is performed to ensure the accuracy of the TCAD model. The experimental results show that the PDE model is not only more consistent with TCAD simulation than the DE model in modeling the single event transient currents of the device, but also that the SER calculated by the LA-SEMT-SER tool based on the PDE model has a smaller error than the SER calculated by the LA-SEMT-SER tool based on the DE model.

Nature of the bond in intermetallic compounds

By studying 398 binary compounds crystallizing in five different crystal structures, it is shown that atomic radii of the elements RA and RB change to reach a constant radius ratio rA/rB(≡ϒ) in a cubic system. In systems of lower symmetry, a range of ϒ values, each corresponding to a certain axial ratio, is possible. Accurate charge values on atoms in solids are derived from the experimental internal radii rA and rB, using Shannon’s compilation of radii versus charge states for elements. It is found, for the first time, that charge transfer and radii change reverse their direction at the ϒ point. Electronegativity difference relative to its value at the ϒ point is recognized to correctly predict the charge transfer and radii changes with RA/RB. The deduced electronic structure of solids, based on spherical ions carrying partial charges, confirms that the metallic atom-pair bond is a resonating polar covalent bond. Identification of the number of electrons that contribute to cohesion and electrical conduction individually, allows successful prediction of electrical conductivity variation for transition metals and p-elements in the periodic table. From a knowledge of accurate valence of elements and of charge on the atoms, variation in the 197Au isomer shift of the gold compounds of CsCl type structure is predicted. The charges on atoms computed using the Quantum Theory of Atoms in Molecules (QTAIM) technique agree with those obtained in our work for compounds belonging to two of the structure types. For compounds belonging to the other three, the charge values obtained by the two methods do not agree. The disagreement correlates to not reckoning the role of the ϒ point. The effect of ϒ point is so fundamental and universal that most physical properties obtained by the secondary processing of primary DFT data, can be influenced by it.

High-Sensitive Detection of E. coli Bacteria Based on Low-Etching Current Density Meso Porous Silicon Electrical Sensor

High-Sensitive Detection of E. coli Bacteria Based on Low-Etching Current Density Meso Porous Silicon Electrical Sensor

Fuel starvation in automotive PEMFC stacks: hydrogen stoichiometry and electric cell-to-cell interaction

Abstract Fuel gross starvation in a polymer electrolyte membrane fuel cell is an error state, during which the supplied amount of fuel is insufficient to sustain the requested electrical current. A novel experimental technique was developed to intentionally provoke well-controlled fuel starvation situations of one single cell in a multi-cell fuel cell stack. This modification was implemented in a 20-cell stack of automotive-sized cell geometry and carbon composite bipolar plates. The intentional fuel starvation situation was analyzed using a printed circuit board to measure the current density distribution in addition to a multipoint cell voltage monitoring to measure local cell voltages. The provoked detrimental subsidiary reactions of the anode were found to take place spatially separated from the normal hydrogen oxidation reaction. It was therefore possible to determine and intentionally vary the hydrogen stoichiometry of the fuel starved cell. This error state caused intense distortions of the starved cells current density distribution and local cell voltages. The maximum difference obtained between outlet and inlet voltage of the modified cell was 1.4 V. Compared to the average current density, a more than 4-times higher maximum local current density was measured in the affected cell. Adjacent cells were also affected via electric cell-to-cell interaction. Characteristic patterns therefore became visible in the cell voltage distribution, measured by the inlet and outlet cell voltage monitoring. The use of carbon composite bipolar plates is favoring the occurrence of these patterns due to their relatively high electric sheet resistance. Using the new hardware setup, we could investigate the relation between the hydrogen stoichiometry of the affected cell during fuel gross starvation and the observed irregular redistribution of current density and local cell voltages.

Steady electric currents in magnetized QCD and their use for the equation of state

In this paper we study the emergence of steady electric currents in QCD as a response to a non-uniform magnetic background using lattice simulations with 2 + 1 quark flavors at the physical point, as well as leading-order chiral perturbation theory. Using these currents, we develop a novel method to determine the leading-order coefficient of the equation of state in a magnetic field expansion: the magnetic susceptibility of the QCD medium. We decompose the current expectation value into valence- and sea-quark contributions and demonstrate that the dominant contribution to the electric current is captured by the valence term alone, allowing for a comparably cheap determination of the susceptibility. Our continuum extrapolated lattice results for the equation of state confirm the findings of some of the existing studies in the literature, namely that the QCD medium behaves diamagnetically at low and paramagnetically at high temperatures.

P-111 Artificial Oocyte Activation (AOA) through piezoelectric stimulation post-Intracytoplasmic Sperm Injection (ICSI) for teratozoospermia patients

Abstract Study question Does employing piezoelectric stimulation on oocytes post-ICSI in teratozoospermia cases affect early embryonic development rates? Summary answer In a retrospective study, piezoelectric stimulation after ICSI showed increased fertilization rates and improved embryo quality in teratozoospermia cases. What is known already Fertilization can fail due to various factors. One of the causes of fertilization failure after ICSI is the inability to achieve oocyte activation, a process initiated by sperm-induced events. Piezoelectric stimulation, a method of artificial oocyte activation, involves applying specific electric currents post-ICSI, elevating Ca+2 levels. Studies suggest its efficacy in enhancing fertilization rates and improving embryo quality, particularly in cases of total fertilization failure and severe sperm abnormalities. However, available literature on the efficiency of electrical stimulation in cases of sperm abnormalities is limited. Study design, size, duration In this retrospective study conducted at our reproductive center between January 2023 and October 2023, we enrolled 122 patients diagnosed with male factor infertility. These patients were divided into two groups: the control group (n = 61) where piezoelectric stimulation was not employed post-ICSI, and the AOA group (n = 61) where piezoelectric stimulation was utilized after the ICSI procedure. Participants/materials, setting, methods The study assessed 2122 oocytes, with 1031 in the control and 1091 in the AOA group. Piezoelectric stimulation was administered oocytes approximately 20-30 minutes after ICSI. The quality of sperm samples was assessed based on Kruger’s strict criteria. Following ICSI, statistical analysis utilized Student’s t-test and chi-squared tests to assess the impact of piezoelectric stimulation on fertilization and embryo quality, considering p < 0.05 as significant and p < 0.001 as highly significant. Main results and the role of chance Clinical outcomes were compared between two groups. No significant differences were observed between the control group and AOA group regarding female age (29.93±4.9 vs. 29.93±5.11, p = 0.988) and male age (34.25±3.45 vs. 33.93±3.64, p = 0.628), the number of retrieved oocytes (16.90±11.04 vs. 17.89±9.3, p = 0.344), the number of metaphase II (11.02±6.8 vs.12.46±6.6, p = 0.162). However, a highly significant difference was noted in the distribution of fertilization rate (59.08% [397/672] vs. 66.84% [508/760], p = 0.002), high-quality embryos rate (day 3) (44.08% [175/397] vs. 54.33% [276/508], p = 0.002), blastocyst rate (40.05% [159/397] vs. 50% [254/508], p = 0.003) and the good blastocyst development rate (14.11% [56/397] vs. 24.41% [124/508], p = 0.0001). Cleavage rate was significantly higher in the AOA group (85.24% [433/508]) than control group (79.09% [314/397]), p = 0.01. Limitations, reasons for caution Constraints include the study’s retrospective, single-center design, and a limited sample size. Wider implications of the findings Piezoelectric stimulation demonstrates effectiveness in improving fertilization rates and embryo quality in teratozoospermia cases after ICSI. Trial registration number not applicable

Chaos control in cardiac dynamics: terminating chaotic states with local minima pacing

Current treatments of cardiac arrhythmias like ventricular fibrillation involve the application of a high-energy electric shock, that induces significant electrical currents in the myocardium and therefore involves severe side effects like possible tissue damage and post-traumatic stress. Using numerical simulations on four different models of 2D excitable media, this study demonstrates that low energy pulses applied shortly after local minima in the mean value of the transmembrane potential provide high success rates. We evaluate the performance of this approach for ten initial conditions of each model, ten spatially different stimuli, and different shock amplitudes. The investigated models of 2D excitable media cover a broad range of dominant frequencies and number of phase singularities, which demonstrates, that our findings are not limited to a specific kind of model or parameterization of it. Thus, we propose a method that incorporates the dynamics of the underlying system, even during pacing, and solely relies on a scalar observable, which is easily measurable in numerical simulations.

Implementation of external magnetic field to improve strength of St37 steel resistance spot weld

AbstractThe magnetic assist technique involves the interaction between an external magnetic field and electrical current which produces Lorentz force that influences the flow pattern of molten metal and ultimately impacts the appearance and microstructure of the weld. Many parameters may influence on this process such as welding current, time, and force as well as the working magnet distance (MD). In this study, the effects of the distance between the permanent magnet’s MD on the heat-affected zone (HAZ) and weld nugget zone (NZ) were examined through mechanical and macro- and microstructural analyses. The results demonstrated that MD has a strong influence on the magnetic flux density which determines the joint appearance, quality, and microstructure of St37 steel. Results showed that with increasing MD, HAZ increased from 8 to 22 mm2 while NZ decreased from 26 to 19 mm2, and also, the grain size increased with increasing MD and reaching 48 µm at MD was set to 9 cm. Moreover, hardness decreased at both areas through increasing MD from (120–110) HV at HAZ and from (170–150) HV at NZ. Under the action of (electromagnetic filed) EMF, weld tensile shear strength and the cross tensile strength give the highest values equal to 172 MPa and 155 MPa, respectively, when MD is set to 4.5 cm. Besides, soundness joint was obtained at MD = 4.5 cm which confirms that this is the best distance between magnets.