Condensed Phase Membrane Introduction Mass Spectrometry Research Articles

Online Membrane Sampling for the Mass Spectrometric Analysis of Oil Sands Process Affected Water-Derived Naphthenic Acids in Real-World Samples

Large volumes of oil sands process-affected waters (OSPW) result from heavy oil extraction in Alberta, Canada. Currently, a toxic legacy of ca. 500 Mm3 is stored in tailings ponds under a zero-discharge policy. OSPW is a complex mixture of suspended and dissolved materials including a wide range of inorganic and organic contaminants. Classically defined naphthenic acids (NAs; CnH2n+ZO2) are one of the primary toxic fractions in OSPW and have therefore been the subject of considerable research interest. Most studies employ considerable sample cleanup followed by liquid chromatography and/or high-resolution mass spectrometry (HRMS) for the characterization of these complex mixtures. However, these strategies can be time- and cost-intensive, limiting the scope of research and adoption for regulatory purposes. Condensed phase membrane introduction mass spectrometry (CP-MIMS) is emerging as a “fit-for-purpose” approach for the analysis of NAs. This technique directly interfaces the mass spectrometer with an aqueous sample using a hydrophobic semi-permeable membrane, requiring only pH adjustment to convert NAs to a membrane-permeable form. Here, we examine the perm-selectivity of classical NAs (O2) relative to their more oxidized counterparts (O3–O7) and heteroatomic (N, S) species collectively termed naphthenic acid fraction compounds (NAFCs). The investigation of 14 model compounds revealed that classically defined NAs are greater than 50-fold more membrane permeable than their oxidized/heteroatomic analogs. HRMS analysis of real OSPW extracts with and without membrane clean-up further supported selectivity towards the toxic O2 class of NAs, with >85% of the overall signal intensity attributable to O2 NAs in the membrane permeate despite as little as 34.7 ± 0.6% O2 NAs observed in the directly infused mixture. The information collected with HRMS is leveraged to refine our method for analysis of NAs at unit mass resolution. This new method is applied to 28 archived real-world samples containing NAs/NAFCs from constructed wetlands, OSPW, and environmental monitoring campaigns. Concentrations ranged from 0–25 mg/L O2 NAs and the results measured by CP-MIMS (unit mass) and SPE-HRMS (Orbitrap) showed good agreement (slope = 0.80; R2 = 0.76).

Aqueous naphthenic acids and polycyclic aromatic hydrocarbons in a meso-scale spill tank affected by diluted bitumen analyzed directly by membrane introduction mass spectrometry

With the increasing use of unconventional, heavy crude oils there is growing interest in potential impacts of a diluted bitumen (DB) spill in marine and freshwater environments. DB has the potential to release several toxic, trace organic contaminants to the water column. Here, the aqueous concentrations and compositions of two classes of organic contaminants, naphthenic acids (NAs) and polycyclic aromatic hydrocarbons (PAHs), are followed over 8 weeks after a simulated spill of DB (10 L) into a freshwater mesocosm (1200 L) with river sediment (2.4 kg). These complex samples contain biogenic dissolved organic matter, inorganic ions, petroleum contaminants, suspended sediments, and oil droplets. We report the first use of condensed phase membrane introduction mass spectrometry (CP-MIMS) as a direct sampling platform in a complex multi-phase mesocosm spill tank study to measure trace aqueous phase contaminants with little to no sample preparation (dilution and/or pH adjustment). CP-MIMS provides complementary strengths to conventional analytical approaches (e.g., gas- or liquid chromatography mass spectrometry) by allowing the entire sample series to be screened quickly. Trace NAs are measured as carboxylates ([M-H]-) using electrospray ionization and PAHs are detected as radical cations (M+•) using liquid electron ionization coupled to a triple quadrupole mass spectrometer. The DB-affected mesocosm exhibits NA concentrations from 0.3 to 1.2 mg/L, which rise quickly over the first 2 – 5 days , then decrease slowly over the remainder of the study period. The NA profile (measured as the full scan in negative-electrospray ionization at nominal mass resolution) shifts to lower m/z with weathering, a process followed by principal component analysis of the normalized mass spectra. We couple CP-MIMS with high-resolution mass spectrometry to follow changes in molecular speciation over time, which reveals a concomitant shift from classical ‘O2’ naphthenic acids to more oxidized analogues. Concentrations of PAHs and alkylated analogues (C1 – C4) in the DB-affected water range from 0 to 5 μg/L. Changes in PAH concentrations depend on ring number and degree of alkylation, with small and/or lightly alkylated (C0 – C2) PAH concentrations rising to a maximum in the first 4 – 8 days (100 – 200 h) before slowly decaying over the remainder of the study period. Larger and heavily alkylated (C3 – C4) PAH concentrations generally rise slower, with some species remaining below the detection limit throughout the study period (e.g., C20H12 class including benzo[a]pyrene). In contrast, a control mesocosm (without oil) exhibited NA concentrations below 0.05 mg/L and PAHs were below detection limit. Capitalizing on the rapid analytical workflow of CP-MIMS, we also investigate the impacts of sample filtration at the time of sampling (on NA and PAH data) and sample storage time (on NA data only).

Direct mass spectrometric analysis of naphthenic acids and polycyclic aromatic hydrocarbons in waters impacted by diluted bitumen and conventional crude oil

Crude oil spills have well-documented, deleterious impacts on the hydrosphere. In addition to macroscopic effects on wildlife and waterscapes, several classes of petroleum derived compounds, such as naphthenic acids (NAs) and polycyclic aromatic hydrocarbons (PAHs), may be released into the water and present aquatic contamination hazards. The concentrations of these contaminants may be affected by both oil type and water chemistry. We characterize the concentrations of NAs and PAHs in natural and constructed waters, spanning a range of pH and salinity, and directly compare the influence of diluted bitumen (DB) and conventional crude (CC) oil, using condensed-phase membrane introduction mass spectrometry (CP-MIMS) as a direct sampling, on-line technique. The concentration and isomer class profiles of classical NAs in the aqueous phase were assessed using electrospray ionization in negative-ion mode as [M-H]− whereas PAH concentrations were monitored using liquid electron ionization (LEI) in positive-ion mode as [M+•]. NA concentrations (0.03–25 ppm) were highly pH-dependent, and an order of magnitude greater in water samples contaminated with DB than CC. Conversely, concentrations of naphthalene (10–130 ppb) and alkyl-naphthalenes (10–90 ppb) were three to four-fold higher in water samples exposed to CC. We demonstrate that naturally occurring dissolved organic matter does not bias results from the membrane sampling approach employed, and that DB and CC contaminated waters can be differentiated using principal component analysis of the NA isomer class distribution in both constructed and natural waters. Finally, we describe the first demonstration of the concurrent analysis of trace NAs and PAHs in the same water sample by controlling perm-selectivity at the membrane and the ionization mode of the mass spectrometer. The techniques employed here for trace analysis of petroleum derived compounds in water can be applied to rapid screening and real-time monitoring of contamination and remediation processes.

Direct Measurement of Acid Dissociation Constants of Trace Organic Compounds at Nanomolar Levels in Aqueous Solution by Condensed Phase-Membrane Introduction Mass Spectrometry.

We report the use of condensed phase-membrane introduction mass spectrometry as a novel method for the determination of acid dissociation constants for hydrophobic organic acids in aqueous solution at nanomolar concentrations. The technique is based on the pH-dependent permeation of analytes through a semipermeable polydimethylsiloxane membrane probe that is immersed directly in aqueous samples. We describe the method and report the dissociation constant (pKa ) values for compounds of biological and environmental relevance, including contaminants, pharmaceuticals, and naphthenic acids. The approach can be applied to individual compounds, combined suites, and complex mixtures at parts-per-billion levels. We report pKa values for 10 carboxylic acids with precision estimates and relative errors (where reliable literature values are available) of <0.1 log units. We report acidity constants for 2-methyl-3-methoxy-4-phenyl butanoic acid (a biomarker for microcystin algal toxins) and 4-t-butylcyclohexane carboxylic acid (a model naphthenic acid) as 4.28 ± 0.03 and 5.15 ± 0.05, respectively. Furthermore, we employ this approach to measure the effect of both temperature and deuterium oxide (heavy water) on acid dissociation, reporting the enthalpy and entropy changes for the ionization of a representative carboxylic acid and substituted phenol. Environ Toxicol Chem 2019;38:1879-1889. © 2019 SETAC.

Direct quantitation and characterization of fatty acids in salmon tissue by condensed phase membrane introduction mass spectrometry (CP-MIMS) using a modified donor phase.

Existing mass spectrometric methods for the analysis of fatty acids often require derivatization, chromatographic separations, and/or extensive sample preparation. Direct mass spectrometry strategies can avoid these requirements, but may also suffer from poor quantitation and/or lack of sensitivity. Condensed phase-membrane introduction mass spectrometry (CP-MIMS) provides direct quantitative measurements of analytes in complex samples with little or no sample preparation. CP-MIMS uses a semipermeable membrane to transfer neutral, hydrophobic compounds from real-world samples to a mass spectrometer. The results presented utilize aqueous/organic sample solvent (donor) mixtures to allow for the sensitive (pptr) detection of a range of fatty acids. The relative sensitivity across a homologous series of fatty acids is observed to change, favoring short- or long-chain fatty acids, depending on the amount of miscible co-solvent added to the donor phase. Further, lithium acetate added online via the acceptor phase was used in tandem mass spectrometry experiments to determine the location of double bonds in polyunsaturated fatty acids (PUFAs). The method was applied to direct measurements and structural determinations for selected PUFAs in salmon tissue samples. Standard addition was employed to quantify the amount of PUFAs in a variety of salmon samples, yielding 0.27-0.42 and 0.40-0.84 w/w % for eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), respectively, for Sockeye and Chinook salmon, in good agreement with the literature. This work presents, to our knowledge, the first use of CP-MIMS for the direct analysis of fatty acids in oily foodstuff samples. Graphical abstract ᅟ.

Polymer Inclusion Membranes with Condensed Phase Membrane Introduction Mass Spectrometry (CP-MIMS): Improved Analytical Response Time and Sensitivity.

Condensed phase membrane introduction mass spectrometry (CP-MIMS) is an online, in situ analysis technique for low volatility analytes. Analytes diffuse through a hollow fiber membrane, where they are then dissolved by a liquid (condensed) acceptor phase flowing through the membrane lumen. Permeating analytes are entrained to an atmospheric pressure ionization source for subsequent measurement by a mass spectrometer. Larger analytes, with inherently lower diffusivities, suffer from lengthy response times and lower sensitivity, limiting the use of CP-MIMS for their online, real-time measurement. We present the use of a heptane cosolvent in a methanol acceptor phase in combination with a polydimethylsiloxane (PDMS) membrane. The heptane generates an in situ polymer inclusion membrane (PIM) with the PDMS. We report improved measurement response times and greater sensitivity across a suite of analytes studied (gemfibrozil, nonylphenol, triclosan, 2,4,6-trichlorophenol, and naphthenic acids), with detection limits in the low parts per trillion (ppt) range. These improvements are attributed to increasing analyte diffusivities, as well as increased analyte partitioning across the PIM. Response times are ∼3× faster for the larger analytes studied, and calibration sensitivity is improved by up to ∼3.5× using 0.046 mole fraction heptane in the methanol acceptor. We report the use of short sample exposure times and the use of non-steady-state signals to reduce the analytical duty cycle, and illustrate that the use of a PIM provides a simple and robust variant of CP-MIMS amenable to rapid screening of analytes in complex samples.

Rapid Screening of Carboxylic Acids from Waste and Surface Waters by ESI-MS/MS Using Barium Ion Chemistry and On-Line Membrane Sampling.

Negative ion tandem mass spectrometric analysis of aliphatic carboxylic acids often yields only non-diagnostic ([M - H](-)) ions with limited selective fragmentation. However, carboxylates cationized with Ba(2+) have demonstrated efficient dissociation in positive ion mode, providing structurally diagnostic product ions. We report the application of barium adducts followed by collision induced dissociation (CID), to improve selectivity for rapid screening of carboxylic acids in complex aqueous samples. The quantitative MS/MS method presented utilizes common product ions of [M - H + Ba](+) precursor ions. The mechanism of product ion formation is investigated using isotopically labeled standards and a series of structurally related carboxylic acids. The results suggest that hydrogen atoms in the β and γ positions yield common product ions ([BaH](+) and [BaOH](+)). Furthermore, the diagnostic product ion at m/z 196 serves as a qualifying ion for carboxylate species. This methodology has been successfully used in conjunction with condensed phase membrane introduction mass spectrometry (CP-MIMS), with barium acetate added directly to the methanol acceptor phase. The combination enables rapid screening of carboxylic acids directly from acidified water samples (wastewater effluent, spiked natural waters) using a capillary hollow fiber PDMS membrane immersion probe. We have applied this technique for the direct analysis of complex naphthenic acid mixtures spiked into natural surface waters using CP-MIMS. Selectivity at the ionization and tandem mass spectrometry level eliminate isobaric interferences from hydroxylated species present within the samples, which have been observed in negative electrospray ionization.

A semi-quantitative approach for the rapid screening and mass profiling of naphthenic acids directly in contaminated aqueous samples.

We report the use of a direct sampling, online analytical approach for the determination of acid extractable naphthenic acids in complex aqueous samples, known as condensed phase membrane introduction mass spectrometry (CP-MIMS). The technique employs a capillary hollow fibre semi-permeable membrane probe configured for immersion into a pH adjusted sample. A continuously flowing methanol acceptor phase transfers naphthenic acids to an electrospray ionization source, operated in negative ion mode, whereupon they are analysed by mass spectrometry as [M-H](-) ions. High-resolution mass spectrometry is used to characterize the influence of sample pH on membrane transport of multiple components of complex naphthenic acid mixtures. We demonstrate the use of CP-MIMS for semi-quantitative analysis of real-world samples using selected ion monitoring and full scan mass spectra at unit mass resolution. The technique has also been employed to continuously monitor the temporal evolution in the mass profile and concentrations of individual naphthenic acid isomer classes in heterogeneous solutions during adsorption processes. Copyright © 2015 John Wiley & Sons, Ltd.

Condensed Phase Membrane Introduction Mass Spectrometry with Direct Electron Ionization: On-line Measurement of PAHs in Complex Aqueous Samples.

Polycyclic aromatic hydrocarbons (PAHs) are USEPA regulated priority pollutants. Their low aqueous solubility requires very sensitive analytical methods for their detection, typically involving preconcentration steps. Presented is the first demonstrated ‘proof of concept’ use of condensed phase membrane introduction mass spectrometry (CP-MIMS) coupled with direct liquid electron ionization (DEI) for the direct, on-line measurement of PAHs in aqueous samples. DEI is very well suited for the ionization of PAHs and other nonpolar compounds, and is not significantly influenced by the co-elution of matrix components. Linear calibration data for low ppb levels of aqueous naphthalene, anthracene, and pyrene is demonstrated, with measured detection limits of 4 ppb. Analytical response times (t10%–90% signal rise) ranged from 2.8 min for naphthalene to 4.7 min for pyrene. Both intra- and interday reproducibility has been assessed (<3% and 5% RSD, respectively). Direct measurements of ppb level PAHs spiked in a variety of real, complex environmental sample matrices is examined, including natural waters, sea waters, and a hydrocarbon extraction production waste water sample. For these spiked, complex samples, direct PAH measurement by CP-MIMS-DEI yielded minimal signal suppression from sample matrix effects (81%–104%). We demonstrate the use of this analytical approach to directly monitor real-time changes in aqueous PAH concentrations with potential applications for continuous on-line monitoring strategies and binding/adsorption studies in heterogeneous samples.

Ionization suppression effects with condensed phase membrane introduction mass spectrometry: methods to increase the linear dynamic range and sensitivity.

Condensed phase membrane introduction mass spectrometry (CP-MIMS) is an online analytical method that allows for the direct, trace level measurement of a wide range of analytes in complex samples. The technique employs a semi-permeable membrane that transfers analytes from a sample into a flowing acceptor solvent, which is directly infused to an atmospheric pressure ionization source, such as electrospray or atmospheric pressure chemical ionization. While CP-MIMS and variants of the technique have been in the literature for nearly a decade, much of the work has focused on instrument development. Few studies have thoroughly addressed quantitative methods related to detection limits, ionization suppression, or linear dynamic range. We examine ionization suppression in the direct rapid quantitation of analytes by CP-MIMS and introduce several analytical strategies to mitigate these effects, including the novel implementation of a continuously infused internal standard in the acceptor phase solvent, and modulation of acceptor phase flow rate. Several representative analytes were used to evaluate this approach with spiked, complex sample matrices, including primary wastewater effluent and artificial urine. Also reported are improved measured detection limits in the low part-per-trillion range, using a 'stopped-flow' acceptor mode.

Delicate polydimethylsiloxane hollow fibre membrane interfaces for condensed phase membrane introduction mass spectrometry (CP‐MIMS)

On-line analytical techniques such as condensed phase membrane introduction mass spectrometry (CP-MIMS) permit direct and rapid analyte measurements in complex samples. Direct, rapid analytical methods are desirable because they eliminate potential contamination and/or dilution from sample workup steps, facilitate rapid sample screening and allow 'real-time' monitoring applications. PDMS hollow fibre membrane (HFM) flow cell interfaces (215 µm, 35 µm, and 0.5 µm thick composite) were coupled with an electrospray ionization (ESI) triple quadrupole mass spectrometer. A simultaneous push/pull methanol acceptor phase delivery system and membrane mounting via epoxy potting ensured that the delicate membranes were not ruptured during construction or sample measurements. Both flow cell and direct insertion 'J-Probe' interfaces using the 0.5 µm thick composite PDMS HFM were utilized for direct naphthenic acid measurements. Delicate HFM CP-MIMS interfaces were used for the rapid screening and continuous, on-line monitoring of carboxylic acids and hydroxylated compounds directly in complex sample matrices under ambient conditions at pptr - ppb detection limits. Push/pull acceptor phase (methanol) delivery maintained ambient hydrostatic pressures within the HFMs, improving ESI stability and analytical sensitivity, especially with stopped acceptor flow operation. Signal response times less than 2 min were achieved for thin, composite PDMS HFMs at 30°C. The continuous monitoring of naphthenic acid degradation was demonstrated. Delicate PDMS HFM CP-MIMS interfaces were developed and used for the direct, on-line detection of low volatility, polar analytes in complex aqueous samples. Composite PDMS HFM interfaces yielded the best overall analytical performance improvements, and were used to demonstrate the direct measurement of naphthenic acids in complex aqueous samples.

A miniature condensed‐phase membrane introduction mass spectrometry (CP‐MIMS) probe for direct and on‐line measurements of pharmaceuticals and contaminants in small, complex samples

High-throughput, automated analytical measurements are desirable in many analytical scenarios, as are rapid sample pre-screening techniques to identify 'positive' samples for subsequent measurements using more time-consuming conventional methodologies (e.g., liquid chromatography/mass spectrometry (LC/MS)). A miniature condensed-phase membrane introduction mass spectrometry (CP-MIMS) probe for the direct and continuous, on-line measurement of pharmaceuticals and environmental contaminants in small, complex samples is presented. A miniature polydimethylsiloxane hollow fibre membrane (PDMS-HFM) probe is coupled with an electrospray ionization (ESI) triple quadrupole mass spectrometer. Analytes are transported from the probe to the ESI source by a methanol acceptor phase. The probe can be autosampler mounted and directly inserted in small samples (≥400 μL) allowing continuous and simultaneous pptr-ppb level detection of target analytes (chlorophenols, triclosan, gemfibrozil, nonylphenol) in complex samples (artificial urine, beer, natural water, waste water, plant tissue). The probe has been characterized and optimized for acceptor phase flow rate, sample mixing and probe washing. Signal response times, detection limits and calibration data are given for selected ion monitoring (SIM) and tandem mass spectrometry (MS/MS) measurements of target analytes at trace levels. Comparisons with flow cell type CP-MIMS systems are given. Analyte depletion effects are evaluated for small samples (≥400 μL). On-line measurements in small volumes of complex samples, temporally resolved reaction monitoring and in situ/in vivo demonstrations are presented. The miniature CP-MIMS probe developed was successfully used for the direct, on-line detection of target analytes in small volumes (40 mL to 400 μL) of complex samples at pptr to low ppb levels. The probe can be readily automated as well as deployed for in situ/in vivo monitoring, including reaction monitoring, small sample measurements and direct insertion in living plant tissue.

Characterization of a condensed‐phase membrane introduction mass spectrometry (CP‐MIMS) interface using a methanol acceptor phase coupled with electrospray ionization for the continuous on‐line quantitation of polar, low‐volatility analytes at trace levels in complex aqueous samples

We report the development and application of a capillary hollow fibre membrane interface using methanol as an acceptor phase to deliver target analytes to an electrospray ionization source and a triple quadrupole mass spectrometer. Superior fluid handling systems lead to greater signal stability and membrane integrity for the continuous on-line monitoring of polar and charged analytes in complex aqueous samples with detection limits in the parts-per-trillion to parts-per-billion range. The system can be operated in either a continuous flow or a stopped acceptor flow mode - the latter giving rise to greater sensitivity. We report detection limits, enrichment factors and signal response times for selected analytes with polydimethylsiloxane and Nafion® polymer membrane interfaces. In addition, we demonstrate the use of this interface to detect pharmaceuticals and other contaminants in natural water and artificial urine. The improved sensitivity and analytical response times of our CP-MIMS system make it possible to continuously monitor dynamic chemical systems with temporal resolutions on the order of minutes. Presented is a comparison of the performance of CP-MIMS versus direct infusion electrospray ionization, demonstrating the potential advantages over direct infusion for trace analyte measurements in complex, high ionic strength samples. Furthermore, by continuously flowing a reaction mixture in a closed loop over the interface, we demonstrate the use of the system as an in situ reaction-monitoring platform for the chlorination of a model organic compound in aqueous solution.