Aerosol Condensation Research Articles

NaCl aerosol filtration over filter media with intrafiber porosity: can filtrate capacity be increased by wicking into this pore volume?

This paper investigates a novel fiber-based filter media wherein a NaCl filtrate is collected and reservoired not only onto the surfaces of the fibers and within their inter-fiber voidage but also within the internal porosity of high pore volume nanoporous fibers or vapor grown carbon nanofibers (VGCF) floc used to fabricate the media. This transport process is shown to occur through a NaCl dissolution into the water-filled nanopores of the fiber and a subsequent intra-fiber wicking phenomenon. The study further elucidates two distinct NaCl accommodation mechanisms which are uniquely available to filter media containing nanoporous intrafiber porosity: (1) wicking and capillary condensation of liquid NaCl aerosols directly into the intrafiber pores at high RH, and (2) dissolution of otherwise solid NaCl aerosols deposited onto fiber surfaces (at low RH) into the interior nanopores of the fiber because these pores (when hydrophilic) are saturated with water (even at low RH). To investigate these two mechanistic regimes, various media were fabricated possessing multiscale porosity in the form of: (i) embedded flocs of VGCFs (4.108 cm3gm-1pore volume), (ii) hydrophilic and high pore volume activated carbon fibers (ACFs, 0.950 cm3gm-1) and (iii) solid graphite fibers. These media were then comparatively evaluated toward NaCl aerosol filtration at different relative humidities. Pressure drop measurements versus filtrate accumulation and SEM-EDAX VGCF demonstrated the location and transport of NaCl into the intrafiber voidage. Media containing both VGCF floc and ACF accumulated 1200% more NaCl at low RH (and a specified pressure drop) than similar media prepared from non-porous graphite fibers, with an additional 315% increase from low to high RH. A Gibbs free energy driving force model is provided to illustrate the driving forces favoring water condensation into the nanopores and solid NaCl aerosol dissolution into the water phase. Filtration efficiency and quality factor assessments for the various media are also systematically evaluated to demonstrate the observed mechanistics.

Unexpected increase of the deuterium to hydrogen ratio in the Venus mesosphere

This study analyzes H2O and HDO vertical profiles in the Venus mesosphere using Venus Express/Solar Occultation in the InfraRed data. The findings show increasing H2O and HDO volume mixing ratios with altitude, with the D/H ratio rising significantly from 0.025 at ~70 km to 0.24 at ~108 km. This indicates an increase from 162 to 1,519 times the Earth's ratio within 40 km. The study explores two hypotheses for these results: isotopic fractionation from photolysis of H2O over HDO or from phase change processes. The latter, involving condensation and evaporation of sulfuric acid aerosols, as suggested by previous authors [X. Zhang et al., Nat. Geosci. 3, 834-837 (2010)], aligns more closely with the rapid changes observed. Vertical transport computations for H2O, HDO, and aerosols show water vapor downwelling and aerosols upwelling. We propose a mechanism where aerosols form in the lower mesosphere due to temperatures below the water condensation threshold, leading to deuterium-enriched aerosols. These aerosols ascend, evaporate at higher temperatures, and release more HDO than H2O, which are then transported downward. Moreover, this cycle may explain the SO2 increase in the upper mesosphere observed above 80 km. The study highlights two crucial implications. First, altitude variation is critical to determining the Venus deuterium and hydrogen reservoirs. Second, the altitude-dependent increase of the D/H ratio affects H and D escape rates. The photolysis of H2O and HDO at higher altitudes releases more D, influencing long-term D/H evolution. These findings suggest that evolutionary models should incorporate altitude-dependent processes for accurate D/H fractionation predictions.

A high-throughput, turbulent-mixing, condensation aerosol concentrator for direct aerosol collection as a liquid suspension

Trace measurement of aerosol chemical composition in workplace atmospheres requires the development of high-throughput aerosol collectors that are compact, hand-portable, and can be operated using personal pumps. We describe the design and characterization of a compact, high flow, Turbulent-mixing Condensation Aerosol-in-Liquid Concentrator (TCALC) that allows direct collection of aerosols as liquid suspensions, for off-line chemical, biological, or microscopy analysis. The TCALC unit, measuring approximately 12 × 16 × 18 cm, operates at an aerosol sample flowrate of up to 10 L min−1, using rapid mixing of a hot flow saturated with water vapor and a cold aerosol sample flow, thereby promoting condensational growth of aerosol particles. We investigated the effect of operating parameters such as vapor temperature, growth tube wall temperature, and aerosol sample flowrate, along with the effect of particle diameter, inlet humidity, aerosol concentration, and operation time on TCALC performance. Nanoparticles with an initial aerodynamic diameter ≥25 nm could grow to droplet diameters >1400 nm with an efficiency ≥80%. Good droplet growth efficiency was achieved for sampled aerosol relative humidity ≥9%. We measured complete aerosol collection for concentrations of ≤3 × 105 cm−3. The results showed good agreement between the particulate mass collected through the liquid collector and direct filter collection. The TCALC eliminates the need for sample preparation and filter digestion during chemical analysis, thereby increasing sample recovery and substantially improving the limit of detection and sensitivity of off-line trace analysis of collected liquid samples.

Compact, high-flow, water-based, turbulent-mixing, condensation aerosol concentrator for collection of spot samples.

A new high-flow, compact aerosol concentrator, using rapid, turbulent mixing to grow aerosol particles into droplets for dry spot sample collection, has been designed and tested. The "TCAC (Turbulent-mixing, Condensation Aerosol Concentrator)" is composed of a saturator for generating hot vapor, a mixing section where the hot vapor mixes with the cold aerosol flow, a growth tube where condensational droplet growth primarily occurs, and a converging nozzle that focuses the droplets into a beam. The prototype concentrator utilizes an aerosol sample flow rate of 4 L min-1. The TCAC was optimized by varying the operating conditions, such as relative humidity of the aerosol flow, mixing flow ratio, vapor temperature, and impaction characteristics. The results showed that particles with a diameter ≥ 25 nm can be grown to a droplet diameter > 1400 nm with near 100% efficiency. Complete activation and growth were observed at relative humidity ≥ 25% of the aerosol sample flow. A consistent spot sample with a diameter of (the diameter of a circle containing 90% of the deposited particles) was obtained regardless of the aerosol particle diameter ( ). For fiber counting applications using phase contrast microscopy, the TCAC can reduce the sampling time, or counting uncertainty, by two to three orders of magnitude, compared to the 25-mm-filter collection. The study shows that the proposed mixing-flow scheme enables a compact spot sample collector suitable for handheld or portable applications, while still allowing for high flow rates.

Improved biomass burning emissions from 1750 to 2010 using ice core records and inverse modeling

Estimating fire emissions prior to the satellite era is challenging because observations are limited, leading to large uncertainties in the calculated aerosol climate forcing following the preindustrial era. This challenge further limits the ability of climate models to accurately project future climate change. Here, we reconstruct a gridded dataset of global biomass burning emissions from 1750 to 2010 using inverse analysis that leveraged a global array of 31 ice core records of black carbon deposition fluxes, two different historical emission inventories as a priori estimates, and emission-deposition sensitivities simulated by the atmospheric chemical transport model GEOS-Chem. The reconstructed emissions exhibit greater temporal variabilities which are more consistent with paleoclimate proxies. Our ice core constrained emissions reduced the uncertainties in simulated cloud condensation nuclei and aerosol radiative forcing associated with the discrepancy in preindustrial biomass burning emissions. The derived emissions can also be used in studies of ocean and terrestrial biogeochemistry.

A Practical Framework for Novel Electronic Nicotine Delivery System Evaluation: Chemical and Toxicological Characterization of JUUL2 Aerosol and Comparison with Reference Cigarettes.

Electronic nicotine delivery systems (ENDSs) are designed as a non-combustible alternative to cigarettes, aiming to deliver nicotine without the harmful byproducts of tobacco combustion. As the category evolves and new ENDS products emerge, it is important to continually assess the levels of toxicologically relevant chemicals in the aerosols and characterize any related toxicology. Herein, we present a proposed framework for characterizing novel ENDS products (i.e., devices and formulations) and determining the reduced risk potential utilizing analytical chemistry and in vitro toxicological studies with a qualitative risk assessment. To demonstrate this proposed framework, long-term stability studies (12 months) analyzing relevant toxicant emissions from six formulations of a next-generation product, JUUL2, were conducted and compared to reference combustible cigarette (CC) smoke under both non-intense and intense puffing regimes. In addition, in vitro cytotoxicity, mutagenicity, and genotoxicity assays were conducted on aerosol and smoke condensates. In all samples, relevant toxicants under both non-intense and intense puffing regimes were substantially lower than those observed in reference CC smoke. Furthermore, neither cytotoxicity, mutagenicity, nor genotoxicity was observed in aerosol condensates generated under both intense and non-intense puffing regimes, in contrast to results observed for reference cigarettes. Following the proposed framework, the results demonstrate that the ENDS products studied in this work generate significantly lower levels of toxicants relative to reference cigarettes and were not cytotoxic, mutagenic, or genotoxic under these in vitro assay conditions.

Experimental study of insoluble aerosol wash-down by condensate on quasi-horizontal plate

The washing behavior of radioactive aerosol caused by condensation on floor is of great significance for evaluating radioactive migration in case of an accident in nuclear power plant. Compared to the inclined or vertical wall, on a nearly horizontal floor the aerosol particles may have a characteristic transport progress, considering the slower speed of the condensate flow and weaker erosion ability to wash-down aerosol due to insufficient shear stress. An experiment in the steam environment is conducted on this study, focusing on condensation and wash-down of deposited insoluble aerosol particles on a 0.4° quasi-horizontal plate. An exponential trend of removed aerosol mass is obtained based on the experimental aerosol transport process on the quasi-horizontal surface. This paper evaluated the effects of particle load and condensation rate on transport process and removed mass. Furthermore, based on the experimental results, a fitting empirical correlation between dimensionless aerosols' removal mass and dimensionless mass of condensate are obtained by modifying the conditions of different condensation rates and aerosol loads.

Development and validation of a method for preparing heated tobacco product aerosol condensate (HTPAC) for large-scale toxicity data acquisition

A method of preparing heated tobacco product aerosol condensate (HTPAC) was developed to expedite HTP toxicity evaluation, and the effectiveness was assessed. To prepare HTPAC, HTP aerosol was generated and collected using a Cambridge filter (particulate phase) and Dulbecco's phosphate buffered saline (DPBS; gaseous phase). The aerosol collected on the Cambridge filter was extracted using methanol, which was thereafter removed by nitrogen purging. The HTP aerosol residue was mixed with DPBS loaded with the collected HTP vapor, ultimately yielding HTPAC. Nicotine and formaldehyde, key harmful compounds in HTP aerosol, were detected in HTPAC (901 ± 224 and 22.2 ± 3.90 µg stick–1, respectively, comparable to those in HTP aerosol (990–1350 (nicotine) and 2.33–21.9 µg stick–1 (formaldehyde)). Propylene glycol and vegetable glycerin, which influence the amount of HTP aerosol, were detected at similar levels in HTPAC and HTP aerosol (propylene glycol = 616 ± 57.1 (HTPAC) and 320–630 µg stick–1 (aerosol) and vegetable glycerin = 2418 ± 224 (HTPAC) and 1667–4000 µg stick–1 (aerosol)). Known components of HTP aerosol (hydroxyacetone, acetic acid, triacetin, and 2-furanmethanol) were also detected in HTPAC. Consequently, HTPAC offers an effective method for concentrating harmful compounds found in HTP aerosols. This, in turn, facilitates comprehensive toxicity assessments, paving the way for guidelines ensuring the safe utilization of HTP.

A new approach of microbiome monitoring in the built environment: feasibility analysis of condensation capture

BackgroundHumans emit approximately 30 million microbial cells per hour into their immediate vicinity. However, sampling of aerosolized microbial taxa (aerobiome) remains largely uncharacterized due to the complexity and limitations of sampling techniques, which are highly susceptible to low biomass and rapid sample degradation. Recently, there has been an interest in developing technology that collects naturally occurring water from the atmosphere, even within the built environment. Here, we analyze the feasibility of indoor aerosol condensation collection as a method to capture and analyze the aerobiome.MethodsAerosols were collected via condensation or active impingement in a laboratory setting over the course of 8 h. Microbial DNA was extracted from collected samples and sequenced (16S rRNA) to analyze microbial diversity and community composition. Dimensional reduction and multivariate statistics were employed to identify significant (p < 0.05) differences in relative abundances of specific microbial taxa observed between the two sampling platforms.ResultsAerosol condensation capture is highly efficient with a yield greater than 95% when compared to expected values. Compared to air impingement, aerosol condensation showed no significant difference (ANOVA, p > 0.05) in microbial diversity. Among identified taxa, Streptophyta and Pseudomonadales comprised approximately 70% of the microbial community composition.ConclusionThe results suggest that condensation of atmospheric humidity is a suitable method for the capture of airborne microbial taxa reflected by microbial community similarity between devices. Future investigation of aerosol condensation may provide insight into the efficacy and viability of this new tool to investigate airborne microorganisms.ImportanceOn average, humans shed approximately 30 million microbial cells each hour into their immediate environment making humans the primary contributor to shaping the microbiome found within the built environment. In addition, recent events have highlighted the importance of understanding how microorganisms within the built environment are aerosolized and dispersed, but more importantly, the lack in development of technology that is capable of actively sampling the ever-changing aerosolized microbiome, i.e., aerobiome. This research highlights the capability of sampling the aerobiome by taking advantage of naturally occurring atmospheric humidity. Our novel approach reproduces the biological content in the atmosphere and can provide insight into the environmental microbiology of indoor spaces.CdiiRnR1NxNeh5S-bH9un_Video

WITHDRAWN: Evaluation of the effects of e-cigarette aerosol extracts and tobacco cigarette smoke extracts on human gingival epithelial cells

Smoking increases the risk of a number of diseases, including cardiovascular, oral and lung diseases. E-cigarettes are gaining popularity among young people as an alternative to cigarettes, but there is debate over whether they are less harmful to the mouth than e-cigarettes. In this study, human gingival epithelial cells (HGECs) were treated with four commercially available e-cigarette aerosol condensates (ECAC) or commercially available generic cigarette smoke condensates (CSC) with different nicotine concentrations. Cell viability was determined by MTT assay. Cell apoptosis was observed by acridine orange (AO) and Hoechst33258 staining. The levels of type I collagen, matrix metalloproteinase (MMP-1, MMP-3), cyclooxygenase 2 and inflammatory factors were detected by ELISA and RT-PCR. Finally, ROS levels were analyzed by ROS staining. The different effects of CSC and ECAC on HGECs were compared. The results showed that higher nicotine concentration of CS significantly reduced the activity of HGECs. By contrast, all ECAC had no significant effect. The levels of matrix metalloproteinase, COX-2, and inflammatory factors were higher in HGECs treated with CSC than those treated with ECAC. In contrast, the level of type I collagen was higher in HGECs treated with ECAC than those treated with CSC. In conclusion, all four flavors of e-cigarettes were less toxic to HGE cells than tobacco, but further clinical studies are needed to determine whether e-cigarettes are less harmful to oral health than conventional cigarettes.

Photooxidation potential of fine particles from desulfurization flue gas aerosol

In China, desulfurization flue gas from coal-fired power plants (CFPPs) has been the focus of research for many years. In this study, for the first time, we simulated the emission process of flue gas and prepared photocatalysts by deposition. An innovative photocatalytic perspective was applied to study the composition, photocatalytic properties, hygroscopicity, and redox properties of the fine particles from flue gas aerosols. The characterization results of XRD, HRTEM, and XPS of freeze-dried desulfurized flue gas samples indicated that aerosol condensation occurred during the smoke plume transportation process, resulting in the formation of well-crystallized fine particles primarily consisting of soluble salts and metal oxides. The UV–vis and ESR results confirmed that desulfurized flue gas has UV light utilization and photocatalytic potential for producing oxidation groups such as hydroxyl radicals and superoxide radicals in light. The subsequent photocatalyst experiments revealed an 85.4 % reduction of 7 ppm isoprene in 30 min; ozone production (373 μg/m3) was observed under more complicated conditions (NO2 = 80 ppb, VOCs = 7 ppm). As a result of the study, a new research approach was proposed for exploring the photoactive potential of flue gas aerosol produced by CFPPs, as well as its impact on the concentration of VOCs and ozone. The finding provided a new possible pathway for desulfurization flue gas emissions and a reference for futureresearch on the observation and control of atmospheric pollution.

E-Cigarette Aerosol Condensate Leads to Impaired Coronary Endothelial Cell Health and Restricted Angiogenesis

Cardiovascular disease (CVD) is a leading cause of mortality worldwide, with cigarette smoking being a major preventable risk factor. Smoking cessation can be difficult due to the addictive nature of nicotine and the withdrawal symptoms following cessation. Electronic cigarettes (e-Cigs) have emerged as an alternative smoking cessation device, which has been increasingly used by non-smokers; however, the cardiovascular effects surrounding the use of e-Cigs remains unclear. This study aimed to investigate the effects of e-Cig aerosol condensate (EAC) (0 mg and 18 mg nicotine) in vitro on human coronary artery endothelial cells (HCAEC) and in vivo on the cardiovascular system using a mouse model of 'e-vaping'. In vitro results show a decrease in cell viability of HCAEC when exposed to EAC either directly or after exposure to conditioned lung cell media (p < 0.05 vs. control). Reactive oxygen species were increased in HCAEC when exposed to EAC directly or after exposure to conditioned lung cell media (p < 0.0001 vs. control). ICAM-1 protein expression levels were increased after exposure to conditioned lung cell media (18 mg vs. control, p < 0.01). Ex vivo results show an increase in the mRNA levels of anti-angiogenic marker, FKBPL (p < 0.05 vs. sham), and endothelial cell adhesion molecule involved in barrier function, ICAM-1 (p < 0.05 vs. sham) in murine hearts following exposure to electronic cigarette aerosol treatment containing a higher amount of nicotine. Immunohistochemistry also revealed an upregulation of FKBPL and ICAM-1 protein expression levels. This study showed that despite e-Cigs being widely used for tobacco smoking cessation, these can negatively impact endothelial cell health with a potential to lead to the development of cardiovascular disease.

Evaluation of the Effects of E-Cigarette Aerosol Extracts and Tobacco Cigarette Smoke Extracts on Human Gingival Epithelial Cells.

Smoking increases the risk of a number of diseases, including cardiovascular, oral, and lung diseases. E-cigarettes are gaining popularity among young people as an alternative to cigarettes, but there is debate over whether they are less harmful to the mouth than e-cigarettes. In this study, human gingival epithelial cells (HGECs) were treated with four commercially available e-cigarette aerosol condensates (ECAC) or commercially available generic cigarette smoke condensates (CSC) with different nicotine concentrations. Cell viability was determined by MTT assay. Cell apoptosis was observed by acridine orange (AO) and Hoechst33258 staining. The levels of type I collagen, matrix metalloproteinase (MMP-1, MMP-3), cyclooxygenase 2, and inflammatory factors were detected by ELISA and RT-PCR. Finally, ROS levels were analyzed by ROS staining. The different effects of CSC and ECAC on HGECs were compared. The results showed that higher nicotine concentration of CS significantly reduced the activity of HGECs. By contrast, all ECAC had no significant effect. The levels of matrix metalloproteinase, COX-2, and inflammatory factors were higher in HGECs treated with CSC than those treated with ECAC. In contrast, the level of type I collagen was higher in HGECs treated with ECAC than those treated with CSC. In conclusion, all four flavors of e-cigarettes were less toxic to HGE cells than tobacco, but further clinical studies are needed to determine whether e-cigarettes are less harmful to oral health than conventional cigarettes.

Intensive aerosol properties of boreal and regional biomass burning aerosol at Mt. Bachelor Observatory: larger and black carbon (BC)-dominant particles transported from Siberian wildfires

Abstract. We characterize the aerosol physical and optical properties of 13 transported biomass burning (BB) events. BB events included long-range influence from fires in Alaskan and Siberian boreal forests transported to Mt. Bachelor Observatory (MBO) in the free troposphere (FT) over 8–14+ d and regional wildfires in northern California and southwestern Oregon transported to MBO in the boundary layer (BL) over 10 h to 3 d. Intensive aerosol optical properties and normalized enhancement ratios for BB events were derived from measured aerosol light scattering coefficients (σscat), aerosol light-absorbing coefficients (σabs), fine particulate matter (PM1), and carbon monoxide (CO) measurements made from July to September 2019, with particle size distribution collected from August to September. The observations showed that the Siberian BB events had a lower scattering Ångström exponent (SAE), a higher mass scattering efficiency (MSE; Δσscat/ΔPM1), and a bimodal aerosol size distribution with a higher geometric mean diameter (Dg). We hypothesize that the larger particles and associated scattering properties were due to the transport of fine dust alongside smoke in addition to contributions from condensation of secondary aerosol, coagulation of smaller particles, and aqueous-phase processing during transport. Alaskan and Siberian boreal forest BB plumes were transported long distances in the FT and characterized by lower absorption Ångström exponent (AAE) values indicative of black carbon (BC) dominance in the radiative budget. Significantly elevated AAE values were only observed for BB events with &lt;1 d transport, which suggests strong production of brown carbon (BrC) in these plumes but limited radiative forcing impacts outside of the immediate region.

Evaluating BC Aging Processes in the Community Atmosphere Model Version 6 (CAM6)

AbstractThe uncertainty of the climatic effect of Black carbon (BC) remains large. One critical uncertainty source that needs to be captured is BC aging. Here we use the Community Atmosphere Model version 6 (CAM6) configured with the four‐mode version of the Modal Aerosol Module (MAM4) to evaluate the modeled BC aging process with recent laboratory and in‐situ measurements over China. As revealed by the comparison of BC aging timescale and number fraction of aged BC against recent measurements, the modeled condensation aging timescale is estimated to be about 0.8 hr (17%) faster than the chamber measurement, and the diurnal variations of modeled BC aging degree are typically higher than observations mainly due to the fast increase in modeled BC aging degree during daytime. Further analysis shows that the condensation aging dominates (&gt;70%) BC aging across China. More specifically, the condensation of secondary organic aerosol (SOA) vapor contributes most to BC aging over China. Slowing down BC aging increases the modeled surface BC concentration over remote Western China and BC burden, but hardly changes surface BC concentration over Eastern China. Our results suggest that BC aging representation in the MAM4 needs to be further improved toward slowing down the BC aging rate, especially the condensation aging by SOA, to improve the BC simulation over remote areas and its impact on BC transport in MAM4.

Arsenic and arsenic species in MOD, POD, and disposable POD electronic cigarette aerosols: a pilot study.

The growing popularity of electronic cigarettes (e-cig) has raised questions about the health effects of e-cig use, or vaping. Previous studies have reported on the potential of exposure to arsenic (As) and other metal(loid)s from vaping, but little is known about the speciation of As in the inhaled aerosols, an important determinant of toxicity. Inorganic As (iAs) species AsIII and AsV are generally more hazardous than organic As species. This study aimed to investigate total and speciated As in condensed aerosols of popular commercial e-cig products and to compare them with regulatory exposure limits. High-performance liquid chromatography and inductively-coupled plasma mass spectrometry were used for As measurements of e-cig aerosol condensates. The analysis included samples from three types of e-cig devices: MODs, PODs, and disposable pod (d-POD) devices. iAs species were identified in all 23 analyzed e-cig aerosol condensate samples, with the highest aerosol concentrations measured in MODs. The geometric mean (range) iAs concentration of 2.3 (1.2-5.1) μg/m3 observed in MOD devices in this study exceeded the recommended exposure limit of 2 μg/m3 for 15-min or shorter inhalation exposures set by the United States National Institute for Occupational Safety and Health. These preliminary results suggest that iAs species are present in inhalable aerosols of some MOD products at levels above regulatory limits for iAs inhalation.

Cytotoxicity and cell injuries of flavored electronic cigarette aerosol and mainstream cigarette smoke: A comprehensive in vitro evaluation

IntroductionAlthough electronic cigarettes (e-cigarettes) have attracted much attention due to their claimed harm-reduction effects compared with conventional cigarettes, the adverse effects of e-cigarette aerosol exposure on human health are still unclear. In this work we compared the cytotoxic effects of combustion cigarettes with four commercially available flavored electronic cigarettes and their main components on ten cell lines. Cell injury mechanism of e-cigarette aerosol and combustible cigarette smoke was also explored using cellular models. MethodsEleven kinds of e-cigarettes aerosol condensates (ECSCs) and cigarette smoke constituent’s condensates (CSC) were collected by Cambridge filter pad, and the nicotine contents were determined by UPLC to provide an equivalent nicotine dosage. The CCK-8 assay was used to measure the cell viability differences between ECSC and CSC. Based on RNA-seq results, we compared the effects of ECSC and CSC on various cell injury pathways. Oxidative stress and inflammatory responses were further tested by Western Blot, immunofluorescence, and qRT-PCR assays. ResultsCSC was found to be more cytotoxic than flavored ECSC and their main components, and BEAS-2B cell line was the most sensitive cells by comparing the IC50 value. With prolonged exposure duration and higher doses, ECSC began to exhibit cytotoxicity at and above 72 µg/mL. The IC50 values of ECSC were 15-fold higher than that of CSC. Transcriptome analyses indicated that cell injury-related processes were enriched after the treatment of CSC. CSC could significantly induce more oxidative stress and inflammatory signals than ECSC. ConclusionECSCs and their components induced significantly less cytotoxicity than CSC under the laboratory exposure conditions, and CSC caused much severe cell injuries. Our study adds to the body of scientific evidence for a more comprehensive safety evaluation of e-cigarette products as compared to cigarettes.

Vertical profiles of cloud condensation nuclei number concentration and its empirical estimate from aerosol optical properties over the North China Plain

Abstract. To better understand the characteristics of aerosol activation ability and optical properties, a comprehensive airborne campaign was conducted over the North China Plain (NCP) from 8 May to 11 June 2016. Vertical profiles of cloud condensation nuclei (CCN) number concentration (NCCN) and aerosol optical properties were measured simultaneously. Seventy-two-hour air mass back trajectories show that during the campaign, the measurement region was mainly influenced by air masses from the northwest and southeast. Air mass sources, temperature structure, anthropogenic emissions, and terrain distribution are factors influencing NCCN profiles. Cloud condensation nuclei spectra suggest that the ability of aerosol to activate into CCN is stronger in southeasterly air masses than in northwesterly air masses and stronger in the free atmosphere than near the surface. Vertical distributions of the aerosol scattering Ångström exponent (SAE) indicate that aerosols near the surface mainly originate from primary emissions consisting of more fine particles. The long-distance transport decreases SAE and makes it vary more in the free troposphere than near the surface. To parameterize NCCN, the equation NCCN=10β⋅σγ is used to fit the relationship between NCCN and the aerosol scattering coefficient (σ) at 450 nm. The fitting parameters β and γ have linear relationships with the SAE. Empirical estimates of NCCN at 0.7 % water vapor supersaturation (SS) from aerosol optical properties are thus retrieved for the two air masses: NCCN=10-0.22⋅SAE+2.39⋅σ0.30⋅SAE+0.29 for northwesterly air masses and NCCN=10-0.07⋅SAE+2.29⋅σ0.14⋅SAE+0.28 for southeasterly air masses. The estimated NCCN at 0.7 % SS agrees with that measured, although the performance differs between low and high concentrations in the two air masses. The results highlight the important impact of aerosol sources on the empirical estimate of NCCN from aerosol optical properties.

Chronic E-Cigarette Use Impairs Endothelial Function on the Physiological and Cellular Levels.

The harmful vascular effects of smoking are well established, but the effects of chronic use of electronic cigarettes (e-cigarettes) on endothelial function are less understood. We hypothesized that e-cigarette use causes changes in blood milieu that impair endothelial function. Endothelial function was measured in chronic e-cigarette users, chronic cigarette smokers, and nonusers. We measured effects of participants' sera, or e-cigarette aerosol condensate, on NO and H2O2 release and cell permeability in cultured endothelial cells (ECs). E-cigarette users and smokers had lower flow-mediated dilation (FMD) than nonusers. Sera from e-cigarette users and smokers reduced VEGF (vascular endothelial growth factor)-induced NO secretion by ECs relative to nonuser sera, without significant reduction in endothelial NO synthase mRNA or protein levels. E-cigarette user sera caused increased endothelial release of H2O2, and more permeability than nonuser sera. E-cigarette users and smokers exhibited changes in circulating biomarkers of inflammation, thrombosis, and cell adhesion relative to nonusers, but with distinct profiles. E-cigarette user sera had higher concentrations of the receptor for advanced glycation end products (RAGE) ligands S100A8 and HMGB1 (high mobility group box 1) than smoker and nonuser sera, and receptor for advanced glycation end product inhibition reduced permeability induced by e-cigarette user sera but did not affect NO production. Chronic vaping and smoking both impair FMD and cause changes in the blood that inhibit endothelial NO release. Vaping, but not smoking, causes changes in the blood that increase microvascular endothelial permeability and may have a vaping-specific effect on intracellular oxidative state. Our results suggest a role for RAGE in e-cigarette-induced changes in endothelial function.

Washing the air: enhanced condensation of water on aerosols to enable their removal

Previous theory (Clement 1985 Proc. R. Soc. A 398 , 307–339.) is applied to calculate water vapour condensation on aerosol in a chamber with a hot water base, a cooled roof and insulated walls. The fractional aerosol condensation of the water vapour is given by the surface condensation numbers, Cn , at the water surface and the roof. The magnitude of the aerosol condensation rate, M , per unit area of the base is then obtained from theory using heat transfer correlations. The central well-mixed turbulent region in the chamber is generally equilibrated, and maximum and minimum values of M are obtained from the limits of complete vapour condensation, and no condensation, in the boundary layers, respectively. Practically all their difference arises in the cold boundary layer where the supersaturation reaches up to 3 for no condensation. Results for M are obtained for water temperatures of 70 and 80°C and roof temperatures of 5–30°C, and range from 0.1 to 1.0 g m −2 s −1 . Chamber properties are compared to those of the Pi chamber used to investigate cloud condensation. Estimations for aerosol growth in the chamber are made for varying chamber heights and aerosol number concentrations, N . Passage of air through such a chamber could effectively grow aerosols of even the highest N up to an easily removable size range in a matter of seconds, enabling the cleaning of polluted air, including that containing viruses.