Concentrations Of Copper Sulfate Research Articles

Optimization studies on laccase activity of Proteus mirabilis isolated from treatment sludge of textile industry factories : Optimization of laccase activity of Proteus mirabilis.

Laccase is an exothermic enzyme with copper in its structure and has an important role in biodegradation by providing oxidation of phenolic compounds and aromatic amines and decomposing lignin. The aim of this study is to reach maximum laccase enzyme activity with minimum cost and energy through optimization studies of Proteusmirabilis isolated from treatment sludge of a textile factory. In order to increase the laccase enzyme activities of the isolates, medium and culture conditions were optimized with the study of carbon (Glucose, Fructose, Sodium Acetate, Carboxymethylcellulose, Xylose) and nitrogen sources (Potassium nitrate, Yeast Extract, Peptone From Soybean, Bacteriological Peptone), incubation time, pH, temperature and Copper(II) sulfate concentration then according to the results obtained. Response Surface Method (RSM) was performed on six different variables with three level. According to the data obtained from the RSM, the maximum laccase enzyme activity is reached at pH 7.77, temperature 30.03oC, 0.5g/L CuSO4, 0.5g/L fructose and 0.082g/L yeast extract conditions. After all, the laccase activity increased 2.7 times. As a result, laccase activity of P. mirabilis can be increased by optimization studies. The information obtained as a result of the literature studies is that the laccase enzymes produced in laboratory and industrial scale are costly and their amounts are low. This study is important in terms of obtaining more laccase activity from P.mirabilis with less cost and energy.

A mathematical model of the copper plating process in restoration of road transport equipment parts

Introduction. The use of restored parts of motor vehicles makes it possible to reduce the financial costs of repairing equipment. The cost of the restored parts should not exceed 50% of the cost of the new part. Increasing the productivity (deposition rate) of an electrolytic copper coating during the restoration of parts of motor vehicles requires taking into account the technological and economic aspects of the restoration process. The study of the factors (deposition conditions) that most affect the deposition process of the copper coating, the analysis of the experimental results and its statistical processing made it possible to optimize the technology of restoration of copper parts to create the most appropriate deposition modes with maximum productivity, thus reducing the cost of restoration of parts of motor vehicles. The purpose of the research is to develop a mathematical model of the effect of deposition conditions (electrolyte temperature, cathode current density) and electrolyte composition (concentration of copper sulfate and sulfuric acid) on the performance of the deposition process of copper coating, for further development of the most productive technology for restoring collectors of electric motors of motor vehicles.Materials and methods. The studies on equipment that allows obtaining the necessary data with the required accuracy were carried out. Mathematical processing using modern statistical data processing tools that excluded possible errors, providing to obtain the dependence of factors with the necessary accuracy was carried out.Results. In the course of studies of copper sulfate electrolytes to obtain an electrolytic copper coating, with the further development of technology for the restoration of automotive parts, it became necessary to determine the effect of deposition conditions – “factors” (cathode current density, electrolyte temperature, copper sulfate concentration, sulfuric acid concentration) on the deposition rate – “response”. It was found that the factor “cathode current density” and the combination of factors “cathode current density” and “sulfuric acid concentration” are the most significant. The deposition conditions in order to obtain the most productive technology for restoring collectors of electric motors of motor vehicles by depositing a copper coating have been optimized. According to the obtained model, the optimal values of the deposition conditions for obtaining the maximum deposition rate are the electrolyte temperature of 35...40 ° C, the cathode current density of more than 5 A/Dm2, the concentration of copper sulfate 200...250 g/l, the concentration of sulfuric acid 40...70 g/l.

High copper levels induce premature senescence in 3T3-L1 preadipocytes

Copper (Cu) dyshomeostasis has been linked to obesity and related morbidities and also to aging. Cu levels are higher in older or obese individuals, and adipose tissue (AT) Cu levels correlate with body mass index. Aging and obesity induce similar AT functional and structural changes, including an accumulation of senescent cells. To study the effect of Cu-mediated stress-induced premature senescent (Cu-SIPS) on preadipocytes, 3T3-L1 cell line was exposed to a subcytotoxic concentration of copper sulfate. After Cu treatment, preadipocytes acquired typical senescence characteristics including diminished cell proliferation, cell and nuclei enlargement and increased lysosomal mass (higher Lamp2 expression and a slight increased number of cells positive for β-galactosidase associated with senescence (SA-β-Gal)). Cell cycle arrest was due to upregulation of p16Ink4aInk4a and p21Waf1/Cip1. Accordingly, protein levels of the proliferation marker KI67 were reduced. Cu-SIPS relates with oxidative stress and, in this context, an increase of SOD1 and HO-1 expression was detected in Cu-treated cells. The mRNA expression of senescence-associated secretory phenotype factors, such as Mmp3, Il-6 and Tnf-α, increased in Cu-SIPS 3T3-L1 cells but no effect was observed on the expression of heterochromatin-associated protein 1(HP1).Although the downregulation of Lamin B1 expression is considered a hallmark of senescence, Cu-SIPS cells presented higher levels of Lamin B1. The dysregulation of nuclear lamina was accompanied by an increase of nuclear blebbing, but not of micronuclei number.To conclude, a Cu-SIPS model in 3T3-L1 preadipocytes is here described, which may be an asset to the study of AT dysregulation observed in obesity and aging.

Accumulation and Potential Remediation of Copper in Golf Course Putting Greens

The objective of this study was to determine the potential accumulation of copper (Cu) within a USGA golf green profile and analyze potential remediation techniques of soils containing toxic Cu concentrations. Accumulation study utilized: copper phthalocyanine pigment (Par), copper hydroxide (Junction DF), varying concentrations of copper sulfate (CuSO4) within irrigation, and combinations of each. Products were applied over 13 weeks at Clemson University horticulture greenhouses with samples taken at thatch depth, 0-5.1 cm below thatch, and 5.1-10.2 cm below thatch at conclusion of study. Average Cu concentrations in thatch layer was 634.7 kg Cu ha-1, with 0 - 5.1 cm and 5.1 - 10.2 cm depth concentrations of 11.26 and 6.84 kg Cu ha-1, respectively. Remediation studies exposed 5 mg Cecil sandy loam to 15 ml 1000 ppm of CuSo4-Cu followed by 4 sequential 20 ml filtration cycles of 1 N ammonium sulfate, 1 N calcium nitrate, 1 N gypsum, or water. Single filtration of ammonium sulfate removed similar or greater amount of Cu than cumulative impact of 4 filtrations of any other products with 2064 mg Cu kg-1. Studies suggest that the management or removal of thatch may alleviate toxic accumulation of copper, however the use of ammonium sulfate in irrigation water may provide additional remediation options to turfgrass managers.

Influence of Copper Sulphate on Anther Culture for Haploid Production in African Marigold (Tagetes erecta L.)

The present study was carried out to improve the yield of androgenesis in marigold, for which copper sulfate was tested during the pretreatment of anther culture at various concentrations. The best results were obtained when copper sulfate was added at 15 µM and 20 µM. With the addition of copper sulphate at 20 µM, the percent of responding anthers increased from 81.6 to 92.2 %. While. percent caulogenesis increased from 66.8 to 78.4 % with copper sulphate concentration of 15 µM. With the same concentration of copper sulphate (15 µM), the number of shoot buds per anther increased from 7.4 to 9.6 and the number of regenerants per anther increased from 5.8 to 8.6. The positive influence of copper sulphate may be due to an increase in the microspore survival during anther culture.

Green synthesis of CuO nanoparticles using Jasmin sambac extract: Conditions optimization and photocatalytic degradation of Methylene Blue dye

This investigation utilized an eco-friendly method to produce copper oxide nanoparticles (CuO NPs) through the utilization of Jasminium sambac leaf extract. Optimization of pH, temperature, reaction time, and copper sulfate concentration were performed. Characterization via UV–Vis, SEM, XRD, FTIR, and EDX techniques revealed a peak at 243 nm in UV–Vis, and an FTIR band at 590 cm−1 confirmed Cu(II) ion reduction to CuO NPs. pH, temperature, reaction time, and copper sulfate concentration were identified as crucial synthesis parameters. EDX analysis indicated a composition of 75.94% copper and 24.06% oxygen. CuO NPs were dispersive, monoclinic, crystalline, and pure, with an average particle size of 13.4 nm. Photocatalytic experiments achieved 97% Methylene Blue dye degradation in 210 min, highlighting the efficacy of the green synthesis method for CuO NPs with significant photocatalytic activity in wastewater remediation.

Influence of remediation by electrokinetic on the chemical and geotechnical properties of clayey soil contaminated by copper sulfate

The enhanced electrokinetic (EK) technique is an innovative approach and increasingly used in remediation of the fine-grained texture soils contaminated with different types of contaminant. In this study, the EK is enhanced by adding an intermediate compartment and using purging solutions at the electrode’s compartments. The natural clayey soil samples were obtained from Al-Ahadab oil field and artificially contaminated with two ratios of copper sulfate (66666.67 and 26666.67 mg/kg). The feasibility of using EK technique was evaluated by the efficiency of extracting copper from soil and the magnitude of recovery in the geotechnical properties of soil. The duration of remediation was continued for about 240-250 hours depending either on the continuity of electroosmosis flow or reach a constant rate of electrical current. The removal efficiency of copper from contaminated soil samples was ranged from 98.4% to 99.6%. The EK remediation technique proved a marginal impact on the specific gravity and Atterberg’s limits, but it has a significant effect on the shear strength parameters and compressibility of soil. Furthermore, the EK technique can be considered an efficient method for removing the low and high concentrations of copper sulfate from clayey soil of low permeability.

Effect of Copper Sulfate Induction on Phyllanthus tenellus Roxb. Total Phenolic and Flavonoid Content

Aims: Plants need an appropriate amount of nutrients such as copper for growth and development. However, excess of copper may interrupt plant development and cause stress that led to biochemical compounds being synthesized. The influence of a high copper sulfate concentration on phenolic and flavonoid content in Phyllanthus tenellus plants was investigated.
 Place and Duration of Study: The experiment was conducted in a government compound at MARDI Serdang, Selangor, Malaysia (2° 59' 31.7292'' N 101° 41' 56.706'' E), from April 2021 to Jun 2021.
 Methodology: The experiment was conducted using a vertical column planting system under a side-netted rain shelter. The plants were subjected to 0.5 M copper sulfate sprayed after 60 days of planting and harvested 0.5, 1.5, 3, 6, 12 and 24 h after sprayed for further analysis. Total phenolic content was calculated as mg gallic acid equivalent and total flavonoid content was measured as quercetin equivalent.
 Results: Highest total phenolic and flavonoid content was detected after 0.5 hours of copper sulfate application and started to decrease towards 24 hours after sprayed. Treated samples showed a 1.18-fold increase in total phenolic content and 1.4-fold increase in total flavonoid content compared to control untreated samples after 0.5 hours of sprayed. Control samples showed stability in both total phenolic and flavonoid content throughout the harvesting periods. Phenolic is the major secondary metabolites in Phyllanthus tenellus plants.
 Conclusion: Data revealed that the application of 0.5 M copper sulfate is able to enhance total phenolic and flavonoid content in Phyllanthus tenellus plants. The study suggested that the optimum harvesting time is 0.5 hours after copper sulfate application.

Evaluation the toxic effect of copper ions on the condition indices of benthic diatom Actinocyclus subtilis (W.Gregory) Ralfs 1861 in the experiment

Introduction. Pollution of marine coastal areas lead to the relevance of environmental monitoring including application of biotesting methods based on- the cultures of unicellular algae. Microalgae have different species-specific resistance to pollutants that expands application of different species as bioindicators of marine pollution.
 The aim of the study was to determine the threshold concentration of copper ions (Cu2+) for the survival and increase in the cells number of benthic diatom Actinocyclus subtilis (W.Gregory) Ralfs 1861 (Bacillariophyta) under the wide range of toxicant concentrations during 10-day toxicological experiments.
 Material and methods. The response of strain culture of the benthic diatom A. subtilis to various concentrations of copper sulfate (ranged from 16 to 1024 μg/l in terms of Cu2+ ions) was studied. In accordance with the previously developed protocol, the following indices were evaluated: alterations in the absolute number and proportion (%) of alive cells in the test-culture, as well as the specific growth rate in the number of A. subtilis cells at different concentrations of toxicant. Counting of alive and dead cells was carried out by micrographs taken for 12–15 random viewing fields under Nikon Eclipse inverted light microscope.
 Results. It was found that in the control and at concentration of copper ions 16 μg/l, the increase in the absolute number of cells in culture is described by sigmoid response curve. At the control еhe exponential growth phase occurs on days 5–7 and at concentration of 16 µg/l on days 3–5 of the experiment. The threshold concentration of copper ions (32 μg/l) which is critical for the survival of A. subtilis was determined, which is 3–7 times lower than threshold level for other benthic diatom species. At concentration of 32 µg/l, the phases of acceleration and exponential growth on the abundance curve are absent. The proportion of living cells in the culture decreases to 80% of the control level on day 3 and to 39% by day 10. At Cu2+ concentrations of 64 µg/l and above, sharp inhibition and death of culture is observed as early as 1–3 days. A positive specific growth rate of A. subtilis culture was revealed in the period of 1–5 days at copper concentration of 16 and 
 32 µg/l, and at concentration of 64 µg/l and higher the culture dies off. Negative values of the specific growth rate for all concentrations of the toxicant within the period of 5–10 days were obtained.
 Limitations. By the results of 10-day experiments the effect of 8 concentrations of copper sulfate on the culture of marine benthic diatom A. subtilis was studied. Three replicates in each concentration and exposure time were measured (1350 measurements in total), which is sufficient sampling for statistically reliable determination of the threshold values of copper ion toxicity for given test object.
 Conclusion. Considering the results obtained, the benthic diatom A. subtilis is highly sensitive to copper ions impact and can be recommended as new test-object for toxicology, as well as for application in monitoring of marine water areas subject to technogenic pollution.

Investigation of Ni-Cu-B and Ni-Cu-Sn-B coatings developed by electroless method

Due to their remarkable mechanical properties and tribological behaviour which is equivalent the hard chrome coating, electroless Nickel–Boron coatings have been employed in a variety of industries. With the advent of emerging and challenging applications, there has been a need to develop newer variants of the novel Ni-B binary variant. The present work therefore investigates Ni-B-Cu coatings in a quest to achieve higher wear and corrosion resistance. A stabilizer free bath and tin chloride stabilized bath was formulated for the same to remove the harmful lead nitrate from the coating formulation. The concentration of copper sulphate was varied from 0.3 to 0.7 g/L in both the bath formulations. Based on the mass gain of the specimens, coatings obtained from 0.6 g/L copper sulphate was further investigated. The surface morphology of as-plated samples was observed which shows nodular structure and the growth was different compared to lead stabilized baths. The constant load and progressive scratch test were done to evaluate scratch hardness and coating failure respectively.

Evaluation of copper-tolerant fungi isolated from Sarcheshmeh copper mine of Iran.

Mycoremediation, a subset of bioremediation, is considered an advanced method to eliminate environmental contaminations. To identify tolerant fungi to copper contamination and study the related gene expression, sampling was carried out from the soil of "Sarcheshmeh Copper Mine," which is one of the biggest open-cast copper mines in the world. A total of 71 fungal isolates were obtained and purified. Afterward, the inhibitory effect of different concentrations (1000, 1500, 3500, 4000, and 5500 ppm) of copper sulfate on mycelial growth was evaluated. Results indicated that only 5500 ppm of copper sulfate inhibited fungal growth compared to the control. Based on the bioassay experiments, three isolates including S3-1, S3-21, and S1-7, which were able to grow on solid and broth medium containing 5500 ppm of copper sulfate at different pH conditions, were selected and identified using molecular approaches. Also, laccase and metallothionein gene expression has been assessed in these isolates. According to the molecular identification using ITS1-5.8S- ITS2 region, isolates S3-1 and S1-7 were identified as Pleurotus eryngii, and isolate S3-21 belonged to the genus Sarocladium. In addition, P. eryngii showed laccase gene expression reduction after 8 days of exposure to copper sulfate. While in the genus Sarocladium, it increased (almost 2 times) from 6 to 8 days. Besides, metallothionein gene expression has increased from 6 to 8 days of copper sulfate treatment compared to the control which reveals its role in copper tolerance of all studied isolates. In this study, Pleurotus eryngii and Sarocladium sp. are introduced as heavy metal tolerant fungi and the related gene expression to copper tolerance was studied for the first time in Iran.

Green Synthesis of Copper Nanoparticles Using Citrullus colocynthis Peel Extract and Antibacterial Activity for Biomedical Applications

A novel and green method was developed to synthesise copper nanoparticles (CuNPs) using Citrullus colocynthis peel extract as a sustainable source. The study is the first to utilise this extract for the environmentally safe and economically efficient synthesis of CuNPs. The impact of experimental parameters, including the copper sulfate concentration, extract volume, reaction time, and temperature, on the synthetic procedure was thoroughly investigated. The as-prepared CuNPs were characterised using HRTEM, FESEM, XRD, EDX, UV–vis spectrophotometry, and FTIR spectroscopy. The CuNPs exhibited a spherical morphology with an average particle size of 9 nm, and the calculated d-spacing values were measured at 0.257 nm. Furthermore, the XRD analysis revealed characteristic diffraction peaks at 2θ angles of 44.56°, 56.1°, and 71.4°. The UV–Vis absorption spectra of the CuNPs displayed a surface plasmon resonance (SPR) peak at 335 nm, corresponding to an energy band gap of 3.47 eV. Further, the FTIR spectra confirmed the interaction between copper and the biomolecules present in the extract, providing evidence of the significant role played by organic compounds in the capping process. The as-prepared CuNPs exhibited strong antibacterial activity against both gram-negative (P. aeruginosa and E. coli) and gram-positive (S. aureus and S. epidermidis) bacteria.

Dissolution of gold in the presence of copper ion and diethylenetriamine (DETA)

ABSTRACT Cyanidation is the most widely used technique for gold extraction worldwide. However, its efficiency in gold extraction has decreased due to gold association with base metals such as copper. Copper is known to form different complexes with cyanide depending on the pulp pH. These Cu-CN complexes deplete the pulp of free cyanide, thereby decreasing gold leaching. The study examined the application of diethylenetriamine (DETA) in cyanidation to minimise copper ions effect on gold cyanidation. Leaching tests performed in the presence of copper ions reduced gold recovery from 93% to 15% at a copper sulphate concentration of 1% and increased cyanide consumption by 10%. The introduction of DETA (between 0.2% and 1%) however restored gold recovery back to normal as the baseline without copper ions and also enabled gold extraction at a reduced cyanide strength. Based on the study, DETA could be used during gold–copper cyanide leaching to minimise the copper ion effect and enhance gold extraction.

Gibberellin (GA3) and Copper Sulfate Pentahydrate (CuSO4·5H2O) Reduce Seeds per Fruit and Increase Fruit Quality in Bac Son Mandarin Fruit

The aim of this study was to find the optimal gibberellic acid (GA3) and copper sulfate (CuSO4·5H2O) concentrations to reduce the number of seeds and increase the quality of Bac Son mandarin fruit. In experiment 1, the control plants (without GA3) were sprayed with water, and the remaining plants were sprayed with different concentrations of GA3 (50, 75, 100, or 125 ppm). In experiment 2, the control plants (without CuSO4·5H2O) were sprayed with water, and the remaining plants were sprayed with different concentrations of CuSO4·5H2O (50, 75, 100, or 125 ppm). Spraying GA3 at 100 ppm in 2018 produced the lowest seed number and the highest theoretical yield. In 2019, spraying GA3 led to a lower seed number and a higher actual yield compared with the control. Similarly, spraying CuSO4·5H2O significantly reduced the number of seeds/fruit and significantly increased the theoretical yield in 2018. In 2019, the total number of seeds/fruit was significantly lower in the CuSO4·5H2O treatments than in the control. Importantly, both GA3 and CuSO4·5H2O treatments did not adversely affect the fruit’s biochemical parameters or yield. These findings demonstrate that spraying GA3 or CuSO4·5H2O at a certain concentration can effectively reduce the number of seeds per fruit in Bac Son mandarin without compromising fruit quality or yield.

Films of Poly(Hydroxybutyrate) (PHB) and Copper with Antibacterial Activity.

Poly(3-hydroxybutyrate), PHB, is a hydrophobic biopolymer with good mechanical and barrier properties. However, neat PHB is a semicrystalline polymer with a relative high degree of crystallinity and poor film properties. In this work, this biopolymer was plasticized with glycerol tributyrate and functionalized with copper (II) sulfate, allowing us to obtain biodegradable antimicrobial flexible films. Films with the minimum inhibitory concentration (MIC) of copper (II) sulfate presented a higher roughness than neat PHB films. The presence of plasticizer significantly improved the copper sulfate diffusion process, which was evidenced by a greater inhibition halo for plasticized materials compared to unplasticized ones, at the same salt concentration. Plasticized PHB with 2.5% copper (II) sulfate inhibited both Gram-positive (Staphylococcus aureus) and Gram-negative (Pseudomona aeruginosa) bacteria, as determined by the bacterial inhibition halo. In addition, neat PHB films and PHB containing copper (II) sulfate did not show in vitro cytotoxicity in the L-929 cell line. Thus, plasticized PHB functionalized with copper (II) sulfate can be used as biodegradable antimicrobial flexible films for different applications.

Effect of Copper Sulphate Exposure on the Oxidative Stress, Gill Transcriptome and External Microbiota of Yellow Catfish, Pelteobagrus fulvidraco.

This study aimed to investigate the potential adverse effects of the practical application of copper sulfate on yellow catfish (Pelteobagrus fulvidraco) and to provide insights into the gill toxicity induced by copper sulphate. Yellow catfish were exposed to a conventional anthelmintic concentration of copper sulphate (0.7 mg/L) for seven days. Oxidative stress biomarkers, transcriptome, and external microbiota of gills were examined using enzymatic assays, RNA-sequencing, and 16S rDNA analysis, respectively. Copper sulphate exposure led to oxidative stress and immunosuppression in the gills, with increased levels of oxidative stress biomarkers and altered expression of immune-related differentially expressed genes (DEGs), such as IL-1β, IL4Rα, and CCL24. Key pathways involved in the response included cytokine-cytokine receptor interaction, NOD-like receptor signaling pathway, and Toll-like receptor signaling pathway. The 16S rDNA analysis revealed copper sulphate altered the diversity and composition of gill microbiota, as evidenced by a significant decrease in the abundance of Bacteroidotas and Bdellovibrionota and a significant increase in the abundance of Proteobacteria. Notably, a substantial 8.5-fold increase in the abundance of Plesiomonas was also observed at the genus level. Our findings demonstrated that copper sulphate induced oxidative stress, immunosuppression, and gill microflora dysbiosis in yellow catfish. These findings highlight the need for sustainable management practices and alternative therapeutic strategies in the aquaculture industry to mitigate the adverse effects of copper sulphate on fish and other aquatic organisms.

Synthesis of Surface Structures during Laser-Stimulated Evaporation of a Copper Sulfate Solution in Distilled Water

The methodology, technique, and results of studies of the formation of films on the glass surface during the irradiation of water solutions of copper sulfate with the laser radiation are presented. We used the nanosecond radiation of an yttrium-aluminum garnet laser with the generation wavelength λ = 1 .06 μm. The studies used solutions with different concentrations of copper sulfate. The structure of the films obtained in this case is compared with the structure of the films obtained as a result of drying the solutions without exposure to a laser radiation. The resulting films have both ordered and disordered structures. The characteristic dimensions of the structural elements of the films are 0.5–2 μm. The transmission of films in the 300–1200 nm spectral region is studied. In general, the resulting films are transparent in this area. Their transmission practically does not depend on the wavelength, but is different for different concentrations of the solution of copper sulfate.

Copper sulfate induces clinico-hematological, oxidative stress, serum biochemical and histopathological changes in freshwater fish rohu (Labeo rohita).

Despite being an essential trace element for numerous metabolic processes and micronutrients, copper (Cu) has induced adverse effects on the environment and public health due to its continuous and widespread use for the last several decades. The current study assessed the hematological and histopathological alterations in the freshwater fish (Labeo rohita) exposed to graded concentrations of copper sulfate. For this purpose, L. rohita fish (n = 72), weighing ~200-215 g, were randomly divided into four experimental groups and then exposed to acute doses of CuSO4, i.e., control, 0.28, 0.42, and 0.56 μgL-1. For comparative analysis of hematological and biochemical changes, blood/serum samples were obtained on 12, 24, and 36 days. Overall, the body weight of fish decreased with the time and dose of CuSO4; as the dose increases, body weight decreases. Dose and time-dependent results were observed in other parameters also. Results showed a significant increase in leukocytes, whereas red blood cells count, Hb, and Hct were significantly reduced in treated groups compared to the control. The mean corpuscular hemoglobin (MHC) and mean corpuscular hemoglobin concentration (MCHC) showed a non-significant decrease in treated groups compared to the control group. Serum biochemical parameters, including total proteins, albumin, and globulin, decreased significantly (p < 0.05). At the same time, alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP), lactate dehydrogenase (LDH), glucose, and cholesterol were significantly (p < 0.05) increased in the treated groups compared to the control group. Significantly (p < 0.05) increased levels of lipid peroxidation while decreased values of antioxidant enzymes, including superoxide dismutase (SOD), catalase (CAT), and reduced glutathione (RGSH) in the blood of fish were recorded. Histopathological examination of fish gills, liver, and kidneys showed inflammation and degenerative changes due to CuSO4 exposure. In the brain tissue, degenerative changes like neuron necrosis, intracellular edema, cytoplasmic vacuolization, and congestion were observed. In conclusion, the study indicates that exposure to copper sulfate, even in smaller concentrations, can cause adverse hematological and histopathological changes in L. rohita fish.

Differences in toxicity and accumulation of metal from copper oxide nanomaterials compared to copper sulphate in zebrafish embryos: Delayed hatching, the chorion barrier and physiological effects

The mechanisms of toxicity of engineered nanomaterials (ENMs) to the early life stages of freshwater fish, and the relative hazard compared to dissolved metals, is only partially understood. In the present study, zebrafish embryos were exposed to lethal concentrations of copper sulphate (CuSO4) or copper oxide (CuO) ENMs (primary size ∼15 nm), and then the sub-lethal effects investigated at the LC10 concentrations over 96 h. The 96 h-LC50 (mean ± 95% CI) for CuSO4 was 303 ± 14 µg Cu L−1 compared to 53 ± 9.9 mg L−1 of the whole material for CuO ENMs; with the ENMs being orders of magnitude less toxic than the metal salt. The EC50 for hatching success was 76 ± 11 µg Cu L−1 and 0.34 ± 0.78 mg L−1 for CuSO4 and CuO ENMs respectively. Failure to hatch was associated with bubbles and foam-looking perivitelline fluid (CuSO4), or particulate material smothering the chorion (CuO ENMs). In the sub-lethal exposures, about 42% of the total Cu as CuSO4 was internalised, as measured by Cu accumulation in the de-chorionated embryos, but for the ENMs exposures, nearly all (94%) of the total Cu was associated with chorion; indicating the chorion as an effective barrier to protect the embryo from the ENMs in the short term. Both forms of Cu exposure caused sodium (Na+) and calcium (Ca2+), but not magnesium (Mg2+), depletion from the embryos; and CuSO4 caused some inhibition of the sodium pump (Na+/K+-ATPase) activity. Both forms of Cu exposure caused some loss of total glutathione (tGSH) in the embryos, but without induction of superoxide dismutase (SOD) activity. In conclusion, CuSO4 was much more toxic than CuO ENMs to early life stage zebrafish, but there are subtle differences in the exposure and toxic mechanisms for each substance.

Effect of copper sulphate on Cryptocaryon irritans based on metabolome analysis.

Cryptocaryon irritans is one of the most harmful marine parasites in mariculture. Copper sulphate is often used to kill parasites and the influence of copper sulphate on the tomont stage of C. irritans was explored in this study. The results showed that excystment rate was not significantly affected when tomonts were exposed to 5 mg/L (76.7%) and 10 mg/L (78.9%) of copper sulphate for 3 h. However, excystment rate was significantly inhibited when exposed to 15 mg/L (33.3%) for 3 h and 5 mg/L (28.9%), 10 mg/L (33.3%) and 15 mg/L (33.3%) for 6 h. After treatment with high concentrations of copper sulphate, the interior of the tomonts was fuzzy under the microscope, and the division process could not be observed. Metabolomic results combined with preliminary transcriptome analysis results showed that the tomonts were induced to produce linoleate, riboflavin, inositol and other substances under the stress of Cu2+ , which affected the antioxidant mechanism of the body. Using MDA content determination and antioxidant enzyme activity analysis, copper sulphate was found to cause oxidative damage to tomonts by affecting the generation of metabolites, leading to the death of tomonts.