Concentration Of Functional Groups Research Articles

Surface state modulation of carbon dots for efficient generation of hydrogen peroxide

Electrocatalytic dual electron oxygen reduction to hydrogen peroxide (2e ORR) is considered a special and sustainable method for on-site continuous production of hydrogen peroxide. Oxygen doped carbon based materials have demonstrated their superiority in the generation of H2O2. However, there is still a lack of direct experimental evidence to determine the true active site on complex carbon surfaces. In this work, we introduce only carboxyl functional groups on the surface of carbon dots by a mild and simple synthesis method to study the specific COOH functional groups on the generation of H2O2. The H2O2 selectivity was correlated with the contents of COOH functional groups. In alkaline environments, the citric acid modified CDs (CA-OCDs) own excellent catalytic ability for 2e ORR, showing a maximum starting potential of 0.829 V (vs. RHE) and a high selectivity of 89.7% over a wide potential range of 0.2-0.7 V (vs. RHE). In actual H2O2 production, the Faraday efficiency (FE) of CA-OCDs can be up to 97%, and the yield achieves 838 mmol gcatalyst-1 h-1. This work provides an effective and simple strategy for designing efficient carbon-based catalysts for sustainable H2O2 electrosynthesis.

Cocoa husk as precursor of carbonaceous materials for supercapacitors electrodes

Activated carbon materials are widely used as high-performance electrodes for supercapacitors because they allow improving the electrochemical performance of these devices. The development of high surface areas and high porosity contributes to the energy storage by double electric layer, whereas the content of different functional groups on their surface to the pseudocapacitive storage. In addition, they can be obtained from lignocellulosic wastes providing a novel and economic perspective for the development of carbon-based electrodes. In this work, activated carbons were synthesized from cocoa husks using KOH as activating agent. The materials were obtained at three impregnation ratios (1:1, 3:1, 5:1) and three carbonization temperatures (500, 650, and 800 °C), optimizing the best conditions to obtain materials with high surface areas and porosity together with surface functional groups to improve energy storage. The results show that the 800 °C synthesized material with 3:1 impregnation ratio presents a capacitance of 120 F/g at 1 A/g, with a retention capacity of 93 % after 12,000 cycles, being the best electrochemical behavior among the carbons prepared. This is attributed to the adequate micro-mesoporosity, content of surface oxygenated functional groups and high surface area (1444 m2/g).

Study on the effects of inorganic salts and ionic surfactants on the wettability of coal based on the experimental and molecular dynamics investigations

Through the evaluation and preparation of a novel inorganic salt composite solution consisting of sodium dodecyl benzene sulfonate (SDBS), the nonionic surfactants polyethylene glycol pisooctyl phenyl ether (Triton X-100), and inorganic salt Na2SO4, based on surface tension, contact angle, settling time, wetting rate, and changes in the surface microstructure and functional groups of coal, this study analyzed the wetting behavior of the solution on coal dust and its adsorption capacity on the surface of coal particles. The results demonstrate that the composite solution of inorganic salts can significantly enhance the wettability of coal samples, reducing the contact angle to 21.54° and lowering the surface tension to 26.10 mN/m. After treatment with the solution, the relative content of oxygen-containing functional groups in the microscopic structure of the coal sample increased to 59.6 % and pores more prominent than 25 nm increased to 34.63 %. Molecular dynamics (MD) simulations of the water-inorganic salt composite solution-coal system are conducted using Materials Studio software, revealing that after the addition of the composite solution, the self-diffusion coefficient (D) of water molecules is 6.3 × 10-9 m2/s, the starting point of the composite solution is 15 Å, and the system's interaction energy increase to 14000 kcal/mol. It further elucidated the modification of the surface molecular structure of coal dust by the inorganic salt composite solution, increasing hydrogen bonds, enhancing wetting, and demonstrating a solid adsorption capability of the inorganic salt composite solution on the surface of coal dust.

Carbon nanostructures synthesis by catalyst-free atmospheric pressure plasma jet

In this study, carbon nanostructures were synthesized utilizing a warm plasma jet at atmospheric pressure in a continuous and catalyst-free process. The procedure and apparatus were designed and constructed in our laboratory. Plasma was generated with 600 W of electrical energy, using a high-voltage, high-frequency alternating current power source. The working gas utilized was a propane/butane mixture, with a concentration ratio of 60:40, respectively. A production rate of 300 mg min−1 of powdered material was achieved, with a particle size between 20 and 100 nm. The product was characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, Raman spectroscopy, x-ray diffraction, and transmission electron microscopy. Results show the formation of multilayer carbon nanostructures with a low content of functional groups; the obtained material presented structural defects and amorphous carbon. This work demonstrates that, with adequate control, warm plasma jet discharges can be employed for the synthesis of carbon nanostructures. The process is scalable and can be utilized for hydrocarbon reforming and hydrogen production. However, further studies are needed to improve the quality of the nanostructures and process efficiency. The synthesized material can potentially be used in gas adsorption or in the manufacture of polymeric nanocomposites with enhanced thermal, electrical, and mechanical properties.

Experimental study on the mechanism of coal spontaneous combustion inhibition by degradation of white-rot fungus

To investigate the mechanism of inhibition of spontaneous combustion of coal by degradation of white-rot fungus, the changes of macroscopic oxidizing characteristics and microstructure of the degraded coal were investigated by the programmed temperature-raising test and the in situ Fourier-transform infrared spectroscopy experiments. The difference in gas production between the degraded coal and the blank samples indicated that the degradation inhibited the oxidation process of coal, and the intensity of the inhibition effect was different at different oxidation stages. The strongest inhibition effect was found in the accelerated oxidation stage, i.e. 80–140 °C. To further analyze the micro-mechanism of the degradation of Phanerochaete chrysosporium affecting the spontaneous combustion of coal, the relative contents of active functional groups in coal samples were compared. The results showed that the degradation affected the relative contents of hydroxyl, aliphatic hydrocarbon, and oxygenated functional groups in coal. Among them, the most significant changes of –OH and –CO- were observed at 80–140 °C. Thus, it was analyzed that Phanerochaete chrysosporium could degrade the macromolecular structure of coal by generating biological enzymes to reduce the number of oxidizable functional groups such as –OH, –CH2, –CH3, –CO-, and so on, thus reducing the risk of spontaneous combustion of coal.

A promotion strategy of enhancing the mercury removal in Shewanella oneidensis MR-1 based on the mercury absorption and electronic consumption via mer operon

Shewanella oneidensis (S. oneidensis) bacteria have bioremediation capabilities for various heavy metals, however, their repertoire of mercury-removal proteins is limited, restricting their effectiveness in mercury remediation. In this study, the integration of an exogenous mer operon into S. oneidensis expanded the range of mercury-removal proteins, significantly boosting both mercury tolerance and removal efficiency. The engineering bacteria (MR-mer) exhibited growth in a 180 mg/L Hg2+ solution, showing a 40% increase in tolerance over S. oneidensis. In a liquid medium with 50 mg/L Hg2+, the MR-mer strain achieved 73% mercury removal efficiency, outperforming the original strain by 50%, and facilitated Hg0 formation on the cell membrane. Extensive analysis of transmembrane structures and Fourier analysis revealed that mer operon proteins might target the cell membrane, modifying its functional group contents to enhance mercury adsorption. Additionally, the absence of the key protein OmcA in the electron transport chain led to a 30% reduction in Hg2+ removal capacity. This suggests that S. oneidensis transfers electrons to the cell surface through this chain, providing electrons for Hg2+ reduction. In conclusion, the mer operon, targeting the cell membrane in MR-mer strain, synergizes with the electron transport chain to markedly elevate Hg2+ removal capability. This approach not only augments Shewanella's mercury biodegradation capacity, but also offers novel perspectives for microbial heavy metal pollutant removal.

Construction of Polycarbonates with Pendant Multifunctional Groups via a One-Step CO2/ Diepoxide Copolymerization Approach.

A "one-step" strategy has been demonstrated for the tunable synthesis of multifunctional aliphatic polycarbonates (APCs) with ethylene oxide (EO), ethylene carbonate (EC), and cyclohexene oxide (CHO) side groups by the copolymerization of 4-vinyl-1-cyclohexene diepoxide with carbon dioxide under an aminotriphenolate iron/PPNBz (PPN = bis(triphenylphosphine)-iminium, Bz = benzoate) binary catalyst. By adjusting the PPNBz-to-iron complex ratio and incorporating auxiliary solvents, the content of functional side groups can be tuned within the ranges of 53-75% for EO, 18-47% for EC, and <1-7% for CHO. The yield and molecular weight distribution of the resulting multifunctional APCs are affected by the viscosity of the polymerization system. The use of tetrahydrofuran as an auxiliary solvent enables the preparation of narrow-distribution polycarbonates at high conversion. This work presents a novel perspective for the preparation of tailorable multifunctional APCs.

Exploring chitosan-plant extract bilayer coatings: Advancements in active food packaging via polypropylene modification

UV-ozone activated polypropylene (PP) food films were subjected to a novel bilayer coating process involving primary or quaternary chitosan (CH/QCH) as the first layer and natural extracts from juniper needles (Juniperus oxycedrus; JUN) or blackberry leaves (Rubus fruticosus; BBL) as the second layer. This innovative approach aims to redefine active packaging (AP) development. Through a detailed analysis by surface characterization and bioactivity assessments (i.e., antioxidant and antimicrobial functionalities), we evaluated different coating combinations. Furthermore, we investigated the stability and barrier characteristics inherent in these coatings. The confirmed deposition, coupled with a comprehensive characterization of their composition and morphology, underscored the efficacy of the coatings. Our investigation included wettability assessment via contact angle (CA) measurements, X-ray photoelectron spectroscopy (XPS), and attenuated total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR), which revealed substantial enhancements in surface concentrations of elements and functional groups of CH, QCH, JUN, and BBL. Scanning electron microscopy (SEM) unveiled the coatings' heterogeneity, while time-of-flight secondary ion mass spectrometry (ToF-SIMS) and CA profiling showed moderately compact bilayers on PP, providing active species on the hydrophilic surface, respectively. The coatings significantly reduced the oxygen permeability. Additionally, single-layer depositions of CH and QCH remained below the overall migration limit (OML). Remarkably, the coatings exhibited robust antioxidative properties due to plant extracts and exceptional antimicrobial activity against S. aureus, attributed to QCH. These findings underscore the pivotal role of film surface properties in governing bioactive characteristics and offer a promising pathway for enhancing food packaging functionality.

Machine learning-based screening of fuel properties for SI and CI engines using a hybrid group extraction method

The design of high-performance fuels is crucial for achieving clean and efficient combustion of engines. In the current study, a framework for machine learning (ML) model-based fuel design is presented to identify compounds with desired properties for internal combustion engine (ICE) applications. Descriptors computed from newly proposed structural and positional-based group extraction method in this study are used as input in ML models due to the simplicity and computational-efficiency. The ML models were trained and validated using publically available experimental data for up to 1135 compounds. The results demonstrated a high level of predictive accuracy, with R2 values generally exceeding 0.99 for 11 physicochemical properties including melting point, boiling point, enthalpy of vaporization, surface tension, dynamic viscosity, low heating value, liquid density, yield sooting index, cetane number, research octane number and motor octane number. Furthermore, by employing the developed ML models to predict new data, a Fuel Property Database containing 1135 fuels with 12 fuel properties is established, enhanced by an interface for a user-friendly Fuel Physicochemical Properties Prediction Tool that facilitates swift property predictions and database expansion. The Pearson correlation coefficient (PCC) approach is subsequently employed to assess the correlation between descriptors and predicted or experimental properties. The strong agreement between the correlations affirms the effective predictive performance of the ML models within the calibrated data range. Additionally, a PCC analysis is conducted to reveal the individual effects of influential factors and their interactions, highlighting significant features like molecular weight size, degree of branching, and functional group content that influence physical and chemical properties, thereby providing valuable insights for fuel design and optimization. Finally, a initial comprehensive data-driven screening was carried out to identify potential fuel candidates that meet the key property limits for combustion applications in both spark-ignition (SI) and compression-ignition (CI) engines.

Study on the Wettability and Methane Desorption Characteristics of Coal under High Pressure with Different Surfactants.

In the process of coalbed methane extraction, due to the strong hydrophilicity of coal, the surface interaction force between water and the coal matrix is strong. The hydrophobic effect of the coal seam during drainage and pressure reduction is not significant, and adsorbed methane is difficult to desorb. In order to reduce the surface interaction force promoting methane desorption between water and coal, the surfactants NH766, G526, and D001 with a concentration of 0.1% were selected. A pressure of 12 MPa, which is close to that used for the on-site mining of coalbed methane in Baode, was selected as the experimental condition to simulate hydraulic fracturing of high fat coal, and the influence of different surfactants on methane desorption characteristics was analyzed. Combining contact angle experiments and infrared spectroscopy experiments, we explored the changes in wettability of the coal samples. We compared the changes in wettability and methane desorption characteristics and explored the similarities between these changes. The experimental results showed that after NH766 treatment, the content of oxygen-containing functional groups in coal rock decreased by 30%, and the contact angle of the coal matrix surface increased by 10°. Furthermore, its hydrophobicity was enhanced, and the desorption amount increased by 24%. In contrast, the oxygen-containing functional groups in coal rock after G526 and D001 treatments increased by 5% and 16%, respectively, and the contact angle of the coal matrix surface became smaller. Furthermore, its hydrophilicity was enhanced, and the desorption amount was reduced by 12.5% and 20%, respectively. NH766 reduces wettability and promotes methane desorption, and it can be applied to improve CBM extraction efficiency. G526 and D001 enhance wettability and inhibit methane desorption, which make them suitable for dust prevention and gas control in coal mines.

Optimization and Mechanism Study of Bonding Properties of CFRP/Al7075 Single-Lap Joints by Low-Temperature Plasma Surface Treatment

This paper studied favorable low-temperature plasma (LTP) surface treatment modes for Carbon Fiber Reinforced Polymer (CFRP)/Al7075 single-lap joints using complex experimental methods and analyzed the failure modes of the joints. The surface physicochemical properties of CFRP after LTP surface treatment were characterized using scanning electron microscopy (SEM), contact angle tests, and X-ray photoelectron spectroscopy (XPS). The influence mechanism of LTP surface treatment on the bonding properties of CFRP/Al7075 single-lap Joint was studied. The results of the complex experiment and range analysis showed that the favorable LTP surface treatment parameters were a speed of 10 mm/s, a distance of 10 mm, and three repeat scans. At these parameters, the shear strength of the joints reached 30.76 MPa, a 102.8% improvement compared to the untreated group. The failure mode of the joints shifted from interface failure to substrate failure. After low-temperature plasma surface treatment with favorable parameters, the CFRP surface exhibited gully like textures, which enhanced the mechanical interlocking between the CFRP surface and the adhesive. Additionally, the surface free energy of CFRP significantly increased, reaching a maximum of 78.77 mJ/m2. XPS results demonstrated that the low-temperature plasma surface treatment led to a significant increase in the content of oxygen-containing functional groups, such as C-O, C=O, and O-C=O, on the CFRP surface.

Overcoming oxygen inhibition in UV photolithography for the fabrication of low-loss polymer waveguides.

Perfluorinated acrylate polymer materials exhibit low absorption loss at 1310 and 1550 nm, but molecular oxygen inhibits their photocuring. We propose a novel, to our knowledge, UV photolithography method incorporating a pre-exposure process for fabricating low-loss perfluorinated acrylate polymer waveguides. During the pre-exposure process, a partially cured thin layer forms on the core layer, effectively overcoming oxygen inhibition in subsequent lithography. Furthermore, the functional group contents of the polymerized materials were characterized by a Raman spectrometer to analyze the development reaction under the pre-exposure layer. Utilizing this improved method, we fabricated a straight waveguide with a length of 21 cm. The experiments showed that the propagation losses are 0.14 dB/cm at 1310 nm and 0.51 dB/cm at 1550 nm. The inter-channel cross talk for a core pitch of 250 µm was measured as low as -49 dB at 1310 nm. Error-free NRZ data transmission over this waveguide at 25 Gb/s was achieved, showcasing the potential in optical interconnect and communication applications.

Tapping the Full Potential of Infrared Spectroscopy for the Analysis of Technical Lignins.

We present an approach to overcome the challenges associated with the increasing demand of high-throughput characterization of technical lignins, a key resource in emerging bioeconomies. Our approach offers a resort from the lack of direct, simple, and low-cost analytical techniques for lignin characterization by employing multivariate calibration models based on infrared (IR) spectroscopy to predict structural properties of lignins (i. e., functionality, molar mass). By leveraging a comprehensive database of over 500 well-characterized technical lignin samples - a factor of 10 larger than previously used sets - our chemometric models achieved high levels of quality and statistical confidence for the determination of different functional group contents (RMSEPs of 4-16 %). However, the statistical moments of the molar mass distribution are still best determined by size-exclusion chromatography. Analyses of over 500 technical lignins offered also a great opportunity to provide information on the general variability in kraft lignins and lignosulfonates (from different origins). Overall, the effected savings in analysis time (>7 h), resources, and required sample mass combined with non-destructiveness of the measurement satisfy key demands for efficient high-throughput lignin analyses. Finally, we discuss the advantages, disadvantages, and limitations of our approach, along with critical insights into the associated chemical-analytical and spectroscopic challenges.

Effect of dilute acid on fulvic acid extracted from lignite

ABSTRACT To explore the effect of dilute acid on the extraction of fulvic acid by lignite using an alkali-soluble acid precipitation method, lignite was acid-precipitated by H2SO4, HNO3, HCl, and H3PO4, and the content, extraction rate, and structural characteristics of fulvic acid were analyzed. The results showed that the highest content of humic acid extracted by HNO3 is 0.3383 mg/mL, and the lowest content of humic acid extracted by sulfuric acid is 0.0817 mg/mL. The highest extraction rate of humic acid derived from lignite extracted by hydrochloric acid is 3.84%, and the lowest extraction rate of humic acid extracted by sulfuric acid is 0.89%. Fulvic acid extracted from lignite contained functional groups such as benzyl, carbonyl, methyl, and hydroxyl, but their contents varied; the benzene ring structure in fulvic acid precipitated by HNO3 was the most pronounced, but the aromatization degree was the lowest. By contrast, the aromatization degree of fulvic acid precipitated by H2SO4 was the highest. This indicates that the functional group contents in humic acid extracted from different dilute acids vary, although the types of functional groups are similar.

Hydrolysis-dominated catalytic system: Hydrogen-free hydrogenolysis of lignin from Pd-MoOx/TiO2

Lignin is continuously investigated by various techniques for valorization due to its high content of oxygen-containing functional groups. Catalytic systems employing hydrolysis‑hydrogenolysis, leveraging the synergistic effect of redox metal sites and acid sites, exhibit efficient degradation of lignin. The predominance of either hydrolysis or hydrogenolysis reactions hinges upon the relative activity of acid and metal sites, as well as the intensity of the reductive atmosphere. In this study, the Pd-MoOx/TiO2 catalyst was found to primarily catalyze hydrolysis in the lignin depolymerization process, attributed to the abundance of moderate acidic sites on Pd and the redox-assisted catalysis of MoOx under inert conditions. After subjecting the reaction to 240 °C for 30 h, a yield of 48.22 wt% of total phenolic monomers, with 5.90 wt% consisting of diphenols, was achieved. Investigation into the conversion of 4-propylguaiacol (4-PG), a major depolymerized monomer of corncob lignin, revealed the production of ketone intermediates, a phenomenon closely linked to the unique properties of MoOx. Dehydrogenation of the propyl is a key step in initiating the reaction, and 4-PG could be almost completely transformed, accompanied by an over 97 % of 4-propylcatechol selectivity. This distinctive system lays a new theoretical groundwork for the eco-friendly valorization of lignin.

Effect of oxidation kinetic aging on the adhesion behaviour of asphalt-aggregate interfaces from molecular view

ABSTRACT Asphalt oxidation kinetic aging effect on the adhesion behavior of asphalt-aggregate interfaces at atomistic scale was investigated in this study. The asphalts were aged at different aging durations. The sulfoxide and carbonyl functional group content as well as SARA fractions of the asphalts at different aging times were studied through the tests of Fourier Transform Infrared Spectroscopy (FTIR) and Saturate, Aromatic, Resin and Asphaltene (SARA) fractions. Asphalt molecular models of virgin, rapid-rate aged, slow-rate aged and full-aged were established based on SARA fractions and FTIR results, to construct asphalt quartz and asphalt-calcite interface systems at different aging stages. The simulation results showed that the nanostructure of asphalt is influenced by the aggregate type and asphalt oxidative aging. The growth rates of adhesion energy of asphalt-quartz and asphalt-calcite systems increase rapidly first and then slowly with aging time, but the growth rates are different. Meanwhile, the Van der Waals energy is the major energy source of adhesion energy, and the contribution of van der Waals and electrostatic energy to adhesion energy is different. The aging of asphaltene and resin promotes the adhesion ability to quartz or calcite, while the aging of aromatic components is not conducive and the saturate has almost no effect.

Untapped potential of food waste derived biochar for the removal of heavy metals from wastewater

The presence of heavy metals in water pose a serious threat to both public and environmental health. However, the advances in the application of low cost biochar based adsorbent synthesize from various feedstocks plays an effective role in the of removal heavy metals from water. This study implies the introduction of novel method of converting food waste (FW) to biochar through pyrolysis, examine its physiochemical characteristics, and investigate its adsorption potential for the removal of heavy metals from water. The results revealed that biochar yield decreased from 18.4 % to 14.31 % with increase in pyrolysis temperature from 350 to 550 °C. Likewise, increase in the pyrolysis temperature also resulted in the increase in the ash content from 39.87 % to 42.05 % thus transforming the biochar into alkaline nature (pH 10.17). The structural and chemical compositions of biochar produced at various temperatures (350, 450, and 550 °C) showed a wide range of mineralogical composition, and changes in the concentration of surface functional groups. Similarly, the adsorption potential showed that all the produced biochar effectively removed the selected heavy metals from wastewater. However a slightly high removal capacity was observed for biochar produced at 550 °C that was credited to the alkaline nature, negatively charged biochar active sites due to O-containing functional groups and swelling behavior. The results also showed that the maximum adsorption was recorded at pH 8 at adsorbent dose of 2.5 g L−1 with the contact time of 120 min. To express the adsorption equilibrium, the results were subjected to Langmuir and Freundlich isotherms and correlation coefficient implies that the adsorption process follows the Freundlich adsorption isotherm. The findings of this study suggest the suitability of the novel FW derived biochar as an effective and low cost adsorbent for the removal of heavy metals form wastewater.

A systematic analysis and optimization of bicarbonate electrolysis based on a bipolar membrane through multiscale simulation

Bicarbonate electrolysis facilitated by bipolar membrane has emerged as a compelling alternative to gaseous CO2 electrolysis, primarily because of its enhanced product concentration and streamlined processes. However, despite increasing attention, a comprehensive understanding of bicarbonate electrolysis has been eclipsed by the complexity of the intertwined electrode reactions and water dissociation promotion mechanisms of bipolar membranes. A physics-based modeling approach has substantial potential to untangle the impact of intertwined physicochemical processes and expedite the optimization of bicarbonate electrolysis. In this study, a multiscale model coupled with a 1D bipolar membrane and a 2D cathode model is presented to explore the effects of bipolar membranes on cathode reactions and performance optimization using H+ flux as a bridge. For a bipolar membrane, the attenuation mechanism of water dissociation involving ohmic and concentration losses is presented and described using mathematical eqs. A quantification metric, the water dissociation efficiency of a bipolar membrane, is proposed to denote the degree of promoted water dissociation. Two noteworthy parameters related to the fixed functional group concentration are determined and detailed: the onset current density required to stimulate water dissociation and the limited water dissociation efficiency caused by attenuation. For the cathode, a synergistic enhancement mechanism among the operating parameters, membrane properties, and cathode properties is identified. The combined effect of these parameters on the electrolytic performance surpasses the sum of their individual enhancements. Following parameter optimization, there is a notable increase in the current density and Faraday efficiency of bicarbonate electrolysis by 68.6 mA/cm2 and 18.3%, respectively. This study provides a holistic understanding of bicarbonate electrolysis and substantial guidance for its future design.

Adsorption properties and mechanism of Cu(II) on virgin and aged microplastics in the aquatic environment.

Microplastics (MPs) migrate by adsorbing heavy metals in aquatic environments and act as their carriers. However, the aging mechanisms of MPs in the environment and the interactions between MPs and heavy metals in aquatic environments require further study. In this study, two kinds of materials, polyamide (PA) and polylactic acid (PLA) were used as target MPs, and the effects of UV irradiation on the physical and chemical properties of the MPs and the adsorption behavior of Cu(II) were investigated. The results showed that after UV irradiation, pits, folds and pores appeared on the surface of aged MPs, the specific surface area (SSA) increased, the content of oxygen-containing functional groups increased, and the crystallinity decreased. These changes enhanced the adsorption capacity of aged MPs for Cu(II) pollutants. The adsorption behavior of the PA and PLA MPs for Cu(II) conformed to the pseudo-second-order model and Langmuir isotherm model, indicating that the monolayer chemical adsorption was dominant. The maximum amounts of aged PA and PLA reached 1.415 and 1.398 mg/g, respectively, which were 1.59 and 1.76 times of virgin MPs, respectively. The effects of pH and salinity on the adsorption of Cu(II) by the MPs were significant. Moreover, factors such as pH, salinity and dosage had significant effects on the adsorption of Cu(II) by MPs. Oxidative complexation between the oxygen-containing groups of the MPs and Cu(II) is an important adsorption mechanism. These findings reveal that the UV irradiation aging of MPs can enhance the adsorption of Cu(II) and increase their role as pollutant carriers, which is crucial for assessing the ecological risk of MPs and heavy metals coexisting in aquatic environments.

Effect of oxygen-containing functional group contents on sorption of lead ions by acrylate-functionalized hydrochar

The surface functional groups of hydrochar are crucial to its surface properties, and their contents are strongly positively correlated with the adsorption performance. In this study, acrylate-functionalized hydrochar (AHC) with varying contents of O-containing functional groups (OFGs) was synthesized via hydrothermal carbonization (HTC) of bamboo, acrylic acid and an initiator, and then deprotonated with NaOH. The AHCs were analyzed by various characterization techniques. During HTC, the higher amount of acrylic acid added led to higher carbon, oxygen and carboxyl contents, and to the larger specific surface area and pore volume of AHC. The adsorption kinetics, isotherms, thermodynamic, ionic strength and pH effects of Pb(II) on AHC were studied. Adsorption isotherms and kinetics obeyed Langmuir and pseudo-second-order models, respectively, indicating adsorption is monolayer chemical process. The adsorptive ability was well linearly related to the OFG contents of AHC. When acrylic acid was added to 25 mL during HTC, the adsorbing ability of AHC over Pb(II) reached 193.90 mg g−1. Hence, direct HTC of acrylic acid, biomass and an initiator can prepare hydrochar with controllable OFG contents, which is a prospective adsorbent for treating metal cations.