Composite Nanofiber Membranes Research Articles

Preparation of MOR/P(S‐co‐VPh) nanofiber composite membrane and its adsorption properties for rubidium ions

AbstractRubidium (Rb), a rare and precious metal, is widely used in high‐tech fields. In this work the structural advantages of mordenite (MOR) and group affinity of phenolic hydroxyl polymers (poly (styrene‐4‐hydroxystyrene) (P(S‐co‐VPh)) are combined to prepare MOR/P(S‐co‐VPh) nanofiber composite membranes with high selectivity and adsorption specificity for Rb+ by electrospinning. The test results show that MOR is successfully anchored on the nanofiber substrate and maintained its complete crystal structure. Adsorption experiments show that the adsorption capacity of Rb+ increases with the increase of MOR content, and pH = 9.0, T = 25°C are the best adsorption conditions. K+ shows the most obvious interference with the adsorption capacity decreased from 60.03 to 39.33 mg/g. The adsorption process follows with the Langmuir isothermal model and pseudo‐second‐order kinetic equation. The chemical adsorption based on the coordination reaction is the control step, and the intraparticle diffusion also has an important effect on the adsorption rate. The recycling test indicates that the prepared nanofiber composite membrane not only has efficient adsorption of Rb+, but also exhibits excellent regeneration and stability, which helps to achieve its widespread application and long‐term operation in harsh environments.

Composite electrospun membranes based on PET-PAN modified with LDH-hybrid as promising adsorbent for pollutants removal from wastewater

<p>The current work reveals the fabrication of a novel nanofiber composite membrane of PET-PAN modified with Mg-Al-LDH-PVA through electrospinning process. The nanocomposite membranes characterization was conducted with different techniques i.e. SEM, EDS, FTIR, XRD, and water contact angle to evaluate the structure and surface morphology. The optimized nanomembrane was utilized as a useful adsorbent for removal of toxic anionic dye Eriochrome Black T (EBT) and cationic dye Methylene blue (MB) from wastewater. Experimental results identified that PPLP3 membrane has a potential for the removal of EBT (83%) and MB (52%) at pH 3 and 7, respectively, from aqueous solution. The optimum adsorption capacity of PPLP3 nanocomposite membrane was identified and calculated as 7.3 mg.g-1 followed by the pseudo 2nd order kinetics and Langmuir adsorption isotherm fit well with R2 values of 0.964 and 0.997, respectively. The synthesized nanocomposite membrane could be utilized for effective adsorption of contaminations from different wastewaters.</p>

Polyvinyl alcohol/polyethyleneimine grafted carbon oxynitride composite nanofiber membranes with the synergistical enhanced photocatalytic degradation and bactericidal performance

AbstractGraphitic carbon nitride (g‐C3N4) has received much attention as a metal‐free photocatalyst for dye degradation and sterilization. However, the low photocatalytic bactericidal activity and the difficulty in recycling have limited its applications. Here, oxidatively modified g‐C3N4 grafted with polyethyleneimine (PEI) nanofiber membranes (PVA/PEI‐OCN) was reported to enhance the photocatalytic activity. The modification by PEI grafting could reduce the recombination rate of photogenerated carriers and lead to more electrons for the photocatalytic reaction. In addition, electron spin resonance (ESR) results showed that the generation of reactive oxygen species (˙OH, ˙O2− and 1O2) were significantly enhanced in photocatalysis, leading to the significant enhancement of photocatalytic bactericidal activity and dye degradation. Furthermore, the PVA/PEI‐OCN nanofiber membranes prepared by electrospinning had smooth surfaces and uniform fiber formation, with an average diameter of 380 ± 60 nm. The tensile strength was about 73.5% higher than that of PVA nanofiber membranes. The inhibition diameter of PVA/PEI‐OCN‐4 against Escherichisa coli (E. coil) could reach 20 ± 0.2 mm, and the maximum degradation efficiency of methylene blue solution (10 mg/L) could reach 92.8% within 120 min. This work provided an effective paradigm for the rational design of metal‐free photocatalytic materials for elimination of bacterial and dye contamination.

Sustained-release of essential oils by polyvinyl alcohol-based nanofibers

Flavored cigarettes are very popular among consumers. However, many essential oils in cigarettes are lost during storage, and the utilization rate of the essential oils during use is low. Therefore, effective packaging and stable sustained release are urgently needed. In this study, a composite electrospun stable nanofiber storage material was prepared for sustained release. Polyethylene glycol, which has good heat storage properties, was selected as the heat storage material to inhibit the release of essential materials during storage. Porous graphene with good thermal conductivity and a porous structure was selected as the heat conductive component to ensure rapid and uniform release. Polyethylene glycol/porous graphene polyvinyl alcohol-mint essential oil sustained-release composite electrospun nanofibers membrane was prepared by electrospinning, and the morphology, composition, thermal properties, and sustained-release properties were tested. The results showed that the composite electrospun nanofiber membrane reduced the loss of mint oil during storage and enabled the rapid release of mint oil at high temperatures. At room temperature, the retention rate of the mint oil was still more than 90% after 120 h, and at a high temperature (75°C) the retention rate was less than 20% after 10 min; that is, 80% of the essential oil material was released within 10 min.

Flexible Piezoelectric Sensor Based on Two-Dimensional Topological Network of PVDF/DA Composite Nanofiber Membrane

AbstractOwing to the robust scalability, ease of control and substantial industrial applications, the utilization of electrospinning technology to produce piezoelectric nanofiber materials demonstrates a significant potential in the development of wearable products including flexible wearable sensors. However, it is unfortunate that the attainment of high-performance piezoelectric materials through this method remains a challenging task. Herein, a high-performance composite nanofiber membrane with a coherent and uniformly dispersed two-dimensional network topology composed of polyvinylidene fluoride (PVDF)/dopamine (DA) nanofiber membranes and ultrafine PVDF/DA nanofibers was successfully fabricated by the electrospinning technique. Based on the evidence obtained from simulations, experimental and theoretical results, it was confirmed that the unique structure of the nanofiber membrane significantly enhances the piezoelectric performance. The present PVDF/DA composite nanofibers demonstrated a remarkable piezoelectric performance such as a wide response range (1.5–40 N), high sensitivity to weak forces (0–4 N, 7.29 V N−1), and outstanding operational durability. Furthermore, the potential application of the present PVDF/DA membrane as a flexible wearable sensor for monitoring human motion and subtle physiological signals has also been validated. This work not only introduces a novel strategy for the application of electrospun nanofibers in sensors but also provides new insights into high-performance piezoelectric materials. Graphical Abstract

Development of highly bacterial filtration efficient and antibacterial cellulose acetate/gum rosin composite nanofibers for facemask application

Cellulose acetate (CA) is a non-toxic, renewable, and biodegradable polymeric material that can be effectively electrospuned into bacterial filtration efficient nanofiber membrane for face mask application. However, its fragile and non-antibacterial nature influenced its scalability. In this context, natural antibacterial gum rosin (GR) additive can be explored. Therefore, the present study aimed to produce a CA/GR composite nanofibers membrane for the finest bacterial filtration, excellent antibacterial moiety, and improved tensile properties for facemask application. Hence, in this work, we have studied the effect of GR concentrations (0–15 g) on the needleless electrospinning behavior and fibers' morphology through rheology, electrical conductivity, and SEM analysis. These analyses revealed that GR significantly affects the fibers' spinning behavior, morphology, and diameter of the produced fibers. Later, ATR-FTIR spectroscopy mapped the functional changes in the produced nanofibers that affirmed the integration of GR with CA polymer. This modification resulted in a 3-fold rise in tensile strength and an 11-fold decline in elongation% in 15 g CA/GR composite nanofibers membrane than the control sample. Furthermore, it has shown 98.79 ± 0.10 % bacterial filtration efficiency and ~ 93 % reduction in Staphylococcus Aureus and Klebsiella Pneumoniae bacterial growth, elucidating a high-efficiency level for potential facemask application.

Nanoparticle-filled oriented nanofiber membrane for effective emulsion separation via spin coating

Patterned membranes, particularly those modified with nanoparticles, are commonly used in the effective filtration separation of emulsions. However, the conventional fabrication methods are based on wet spinning that require large quantities of organic solvents, necessitating treatment and recycling. This increases the economic and environmental cost, damages the environment, and lowers the production efficiency. In this study, we develop a novel spin-coating method to directly fabricate oriented and patterned nanofiber membranes from powders without harsh solution treatment. The patterned nanofiber membrane exhibits a higher flux than a traditional porous membrane with disordered nanofibers and the same retention rate. The use of oriented nanofiber membranes filled with multi-walled carbon nanotubes and graphene enhances the emulsion-breaking effect during emulsion separation. The effect of the type and diameter of the nanofibers on the orientation degradation of the oriented nanofiber membrane is analyzed. The combination of nanofiber membranes with nanoparticles enables the design and synthesis of composite nanofiber membranes with precisely tailored pore structures for various applications.

Efficient Cr(VI) remediation by electrospun composite porous nanofibers incorporating biomass with metal oxides and metal-organic framework

To develop a highly efficient adsorbent to remediate and remove hexavalent chromium ions (Cr(VI)) from polluted water, cellulose acetate (CA) and chitosan (CS), along with metal oxides (titanium dioxide (TiO2) and ferroferric oxide (Fe3O4)), and a zirconium-based metal-organic framework (UiO-66) were used to fabricate the composite porous nanofiber membranes through electrospinning. The adsorption performance, influencing factors, adsorption kinetics and isotherms of composite nanofiber membranes were comprehensively investigated. The multi-layer membrane with interpenetrating nanofibers and surface functional groups enhanced the natural physical adsorption and provided potential chemical sites. The thermal stability was improved by introducing TiO2 and UiO-66. CA/CS/UiO-66 exhibited the highest adsorption capacity (118.81 mg g−1) and removal rate (60.76%), which were twice higher than those of the control. The correlation coefficients (R2) of all the composite nanofibers regressed by the Langmuir model were significantly higher than those by the Freundlich model. The pseudo-first-order kinetic curve of CA/CS composite nanofibers showed the highest R2 (0.973), demonstrating that the whole adsorption process involved a combination of strong physical adsorption and weak chemical adsorption by the amino groups of CS. However, the R2 values of the pseudo-second-order kinetic model increased after incorporating TiO2, Fe3O4, and UiO-66 into the CA/CS composite nanofiber membranes since an enhanced chemical reaction with Cr (VI) occured during the adsorption

Electrospun polylactic acid nanofibers membrane with copper ion-loaded clay nanotubes for fresh-keeping packaging

The plastics derived from fossil fuels for food packaging results in serious environmental problems. Developing environment-friendly materials for food packaging is urgent and essential. In this study, polylactic acid (PLA) composite nanofibers membranes were prepared with good biocompatibility and antibacterial property. Cu2+ loaded in the natural halloysite nanotubes (HNTs) was used for the antibacterial agent. Cu2+ was loaded in the HNTs and was confirmed by the X-ray photoelectron spectroscopy (XPS). PLA nanofibers with different HNTs-Cu content were continuous nanofibers with the nanoscale range. HNTs-Cu entered into the nanofiber successfully. Thermal analysis results showed composite nanofibers had good thermal stability. Composite nanofiber membranes had the good hydrophobic property. HNTs-Cu improved the mechanical property of composite nanofibers than pure PLA nanofibers. Tensile strength and elasticity modulus of composite nanofibers with 4 % HNTs-Cu content were the most outstanding. L929 cells were cultured on the nanofiber membranes for biocompatibility evaluation. Cell viability of nanofiber membranes was above the 90 %. Cell live/dead staining results showed L929 cells was seldom dead on the nanofiber membranes. PLA/HNTs-Cu nanofiber membranes exhibited excellent antibacterial effects on S. aureus and E. coli. The inhibitory rates against S. aureus and E. coli were 98.31 % and 97.80 % respectively. The fresh-keeping effects of nanofiber membranes were evaluated by the strawberry preservation. Strawberries covered by nanofiber membranes exhibited better appearance, lower weight loss and higher firmness than control, PLA and PLA/HNTs groups. It promised that PLA/HNTs-Cu composite nanofiber membranes have the significant potential application for active food packaging.

Constructing high-performance nanofiltration membranes using nanofiber supports: Effects of structural stability and polyvinyl alcohol interlayers

Nanofiber supports are promising candidates for constructing high-performance nanofiltration (NF) membranes due to their unique interconnected pores and high porosity. Conventional nanofiber supports usually possess excessive surface roughness and low structural stabilities, influencing the formation of polyamide separation layers. However, research on the effects of nanofiber support properties on the NF membrane performances is relatively few. In this study, we systematically evaluated the effects of structural properties of the nanofiber supports on the performances of the fabricated thin-film nanofiber composite (TFNC) NF membranes. The polyimide (PI) support with heat-pressing post-treatments owns a smooth surface and high structural stability due to the welding and compaction of the PI nanofibers. This promoted the formation of a polyamide separation layer with high smoothness and low fouling tendencies. Consequently, the mechanical strength and long-term operation stability of the TFNC-PI NF membrane were much stronger than that of the membranes with polyacrylonitrile (PAN) and PVDF nanofiber supports. Membrane performance analyses illustrated that the TFNC NF membranes possess notable higher water permeance while slight lower salt rejection than the commercial NF membrane. Compared to TFNC-PAN NF membranes (18∼20 L m-2h−1 bar−1), the water permeance of the structurally stable TFNC-PI NF membrane was relatively low (15–16 L m-2h−1 bar−1) due to its smaller surface filtration area and membrane pore size. Further attempts illustrated that constructing interlayers with 2 wt% polyvinyl alcohol (PVA) coating solutions resulted in the formation of clear and regular Turing structures in the polyamide surface layer. It notably enhanced the water permeance of the membrane by ∼30 % without compromising the salt rejection capability of the membrane. This study provides fundamental insights into the effects of nanofiber support properties on NF performance and feasible pathways to construct high-performance TFNC NF membranes.

Preparation of modified halloysite nanotubes@Ag3PO4/polyacrylonitrile electrospinning membranes for highly efficient air filtration and disinfection

Particulate matters (PMs) and airborne bacteria are among the most severe indoor air issues due to their substantial implications for human health. Therefore, it was imperative to conduct a comprehensive investigation on air filtration materials with superior filtration performance and antibacterial properties. Here, the m-Hal@Ag3PO4 composite particles were prepared by using modified halloysite nanotubes (m-Hal) as the support of Ag3PO4 nano-photocatalysts. These composite antibacterial particles were uniformly dispersed within a polyacrylonitrile (PAN) solution and were subsequently electrospun into m-Hal@Ag3PO4/PAN composite nanofiber membranes (CNMs) possessing excellent antibacterial properties. The incorporation of 30 wt% m-Hal@Ag3PO4 additionally enhanced the filtration efficiency of PM0.3 to 99.9%, at an airflow rate of 32 L/min, while concurrently reducing the pressure drop by 36.7%. The photocatalytic degradation efficiency of CNMs towards ciprofloxacin reached 99%. The antibacterial experiments demonstrated that CNMs exhibited potent antibacterial activity against both Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli)under dark and light conditions. Under visible light irradiation, the average diameter of the inhibition zone for the composite membrane surpassed that observed under dark conditions, indicating a predominant enhancement in its antibacterial efficacy through photocatalysis. The enhanced photocatalytic performance and excellent stability can be attributed to the incorporation of Ag3PO4 with m-Hal, which enhanced the dispersibility and facilitated efficient carrier separation of Ag3PO4. The present type of CNMs exhibited the advantages of high efficiency and low resistance air filtration, photodegradation ability, and recyclability, thereby enhancing the efficacy and lifespan of PMs filtration, bacteria disinfection, and antibiotic degradation. This offered a novel concept and viable approach for indoor air and water purification based on electrospinning technology.

Integration of adsorption, reduction, and filtration in PANI/PVDF nanofiber composite membrane for removal of Cr(VI).

Here, polyaniline/polyvinylidene fluoride (PANI/PVDF) nanofiber composite membrane was fabricated using electrostatic spinning technology to remove hexavalent chromium Cr(VI). The employment of PANI not only extremely enhanced the hydrophilic property of the nanofiber membrane, but also facilitated the transfer of Cr2O72- from water to the membrane. The PANI/PVDF membrane had an extremely excellent performance in getting rid of Cr(VI) and a quite large flux (250 L/m2 h). The maximum adsorption quantity of the membrane could reach 334.5mg/g in which adsorption played 52.12% part and reduction played 47.87% part. The removal rate could reach nearly 100% immediately in the permeate solution under filtration while it needed 240min to reach 100% only by static adsorption. Therefore, the interception of the membrane and the adsorption reduction of PANI had synergistic effect on removal of Cr(VI). Furthermore, the removal rate of Cr(VI) could still reach 95.97% after reused 8 times. The membrane showed a very good reusability and application prospect.

Resistance‐type strain sensor based on carbon nanofiber/polypyrrole composite membrane with high sensitivity

AbstractCarbon nanofibers have been widely studied as one of the promising materials for fabricating flexible electronic strain sensors. Surface modification of carbon nanofibers by conducting polymers is a simple yet effective approach to constructing strain sensors with good conductivity and sensitivity. In this work, composite nanofiber membranes composed of carbon nanofiber and conducting polymer are developed via in situ polymerization of pyrrole, aniline, and thiophene respectively on the surface of the carbon nanofiber which serves as a substrate. Different composite membranes, CNF@PANI, CNF/Ppy, and CNF@PTh, are successfully manufactured. The conducting polymer‐carbon nanofiber composite membranes exhibit improved conductivity as well as response sensitivity compared to pristine carbon nanofiber membranes. Among different composite membranes being studied, CNF/Ppy demonstrates the highest strain‐sensing performance. It shows good sensitivity, reproducibility, and stability in detecting both subtle (strain = 0.1%) and large (strain = 25%) deformation. The excellent strain‐sensing performance of CNF/Ppy endows the composite membrane with great potential for applications in wearable electronics.Highlights Adding PANI, Ppy, and PTh could improve the conductivity of the CNF sensor. Ppy doping has a good effect on the performance of the CNF strain sensor. CNF/Ppy strain sensor has high sensitivity, stability, and durability. CNF/Ppy sensors can detect deformation caused by human movement. CP‐CNF composite material has good flexibility and mechanical properties.

High performance bimetallic ZIF-CoZn@PVDF-HFP composite nanofiber membrane for membrane distillation based on coaxial electrospinning technology

Membrane Distillation (MD) technology stands out for its cost-effectiveness and sustainability in diverse applications, such as high-salinity wastewater treatment and seawater desalination. However, conventional MD membranes frequently encounter challenges associated with inadequate permeate flux and insufficient anti-wetting performance. In the present study, we fabricated a series of ZIF-CoZn@PVDF-HFP composite nanofiber membranes with a core–shell structure via coaxial electrospinning. Here, PVDF-HFP functions as the core, while a blend of bimetallic Zeolitic imidazolate framework ZIF-CoZn nanoparticles and PVDF-HFP constitutes the shell. Through the utilization of the coaxial technology, functional nanoparticles achieve uniform and stably dispersed on the nanofiber surface, leading to the creation of a secondary rough structure in addition to the inherent roughness of single-nozzle electrospinning. This results in a surface with a 3D-hierarchical structure. The significantly amplifies the evaporation area on the surface of the composite nanofiber membrane, thereby bolstering the permeate flux in the MD process. Additionally, the incorporation of bimetallic ZIF-CoZn nanoparticles, recognized for their superior hydrophobicity and low thermal conductivity, improves the anti-wetting and heat-insulating properties of the composite nanofiber membrane, further advancing permeate flux performance. Using a 35 g L−1 NaCl as the feed solution, the optimal 1 % ZIF-CoZn@PVDF-HFP composite nanofiber membrane demonstrated a permeate flux of 21.8 L m−2 h−1, coupled with a salt rejection rate exceeding 99.9 %. Even during long-term MD testing, it maintained excellent insulation and anti-wetting capabilities. Our research offers a convenient and effective approach for fabricating anti-wetting composite nanofiber membranes.

Preparation and adsorption behavior investigation of polypropylene/organically modified saponite nanocomposites fiber membrane with strong oil‐adsorption

AbstractTo improve the adsorption and reusability of polypropylene (PP) fiber membranes, the organically modified saponite (Sap@P(St‐co‐MMA)) was prepared by solution polymerization. Furthermore, PP‐based nanocomposite fiber membranes with strong oil adsorption, thermal stability, and reusability were prepared via melt‐blown technology. The increased specific surface area of PP‐based nanocomposite fiber membranes (PP‐1.5%) provided more active sites for the oil adsorption. Simultaneous rheology and Fourier transform infrared measurements tests showed that Sap@P(St‐co‐MMA) enhanced the crystallinity of PP matrix, promoted the regular arrangement of molecules, and improved the intermolecular interaction force, which was beneficial for the oil adsorption. The adsorption of PP‐1.5% (1.5 wt% addition of Sap@P(St‐co‐MMA)) fiber membrane for xylene and kerosene reached a maximum of 15.84 and 22.84 g g−1, respectively. In the treatment of coal tar wastewater, the removal rate of oil can reach 62.9%, and the removal rate can still reach 51.17% after five cycles of experiments. In summary, PP‐1.5% fiber membrane does not produce secondary pollution to the environment, and is a kind of oil removal material with good application prospect.Highlights PP‐based nanocomposites fiber membrane with strong oil adsorption was prepared. Organically modified saponite had strong heterogenous nucleation for PP matrix. Sap@P(St‐co‐MMA) increased the specific surface area of PP‐based fiber membrane.

Fabrication of multifunctional composite nanofibrous membranes for antibacterial, waterproof, and broad-range microwave absorption properties

The scientific community has shown great interest in high-performance multifunctional nanomembranes due to their increasing demand. Nevertheless, the development of multifunctional composite nanofibrous membranes faces a limitation in achieving consistent and optimal performance with balancing conflicting requirements across multiple functionalities. However, addressing this challenge, a single composite nanofibers membrane has been successfully fabricated, demonstrating effective antibacterial activity, waterproofing properties, and excellent electromagnetic (EM) wave absorption. The multifunction composite nanofibers (CNFs0.6-Co@Fe3) exhibited remarkable microwave absorption performance, with a reflection loss (RL) of 29.10 dB at 15–20 GHz and a thickness of 1.5 mm. Additionally, the nanocomposite displayed flexibility, hydrophobicity with a water contact angle larger than 95° and low surface energy, and significant antibacterial properties against Escherichia coli (E. coli). These multifunctional nanocomposites offer a unique combination of outstanding EM wave absorption, cost-effective fabrication, environmental friendliness, and lightweight characteristics, holding great promise for future applications in nanocomposite products.

A silver-loaded graphene oxide-functionalized Bi-Photothermal composite nanofiber membrane for solar-driven desalination

We have identified a synergistic effect between graphene oxide (GO) and silver (Ag) that significantly enhances the light absorption capacity of silver-loaded graphene oxide (GO-Ag) composite materials. Here we have developed a bi-photothermal electrospun nanofiber membrane (EFM), combining the GO-Ag and polyacrylonitrile (PAN), to improve solar-driven desalination. The characterization results demonstrate that GO-Ag uniformly dispersed within the fiber membrane as a photothermal conversion material enables the GO-Ag/PAN EFM to achieve a remarkable optical absorption of 97 %. And under 1 sun irradiation, the membranes rapidly reach a maximum temperature of 56.3 °C, showcasing exceptional photothermal conversion ability during evaporation. Additionally, the super-hydrophilic porous materials GO-Ag/PAN EFMs exhibit an impressive water evaporation rate of 1.61 kg m-2h−1, accompanied by a photothermal conversion efficiency of 93.3 % under 1 sun. Moreover, the GO-Ag/PAN EFMs demonstrate a remarkable desalination of 99.9 % and salt resistance performance for seawater.

Multifunctional electrospun PP/PVDF‐HFP/MIL‐53(Fe) composite nanofiber membrane for air filtration and dye degradation

AbstractIn this paper, a high‐performance composite nanofiber membrane with excellent air filtration and dye degradation properties was prepared by incorporating MIL‐53(Fe) nanoparticles into the electrospinning solution. The results showed that the filtration efficiency for PM2.5 of the PP/PVDF‐HFP/MIL‐53(Fe) composite nanofiber membrane reached up to 99.3% with the addition of 2 wt% MIL‐53(Fe). Moreover, the composite nanofiber membrane exhibited steady filtration efficiency across different parameters, including air velocity, PM2.5 concentration, and extended testing time. Furthermore, the incorporation of MIL‐53(Fe) significantly enhanced the removal efficiency of the composite nanofiber membrane toward Rh B, resulting in a remarkable 91% removal rate. The polymer/MOF composite nanofiber membranes prepared by simple and cheap electrospinning technology have a wide range of practical applications in the field of environmental protection.Highlights PPM composite nanofiber membrane was prepared via electrospinning method. MIL‐53(Fe) nanoparticles were introduced to PPM composite nanofiber membrane. PPM composite nanofiber membrane showed excellent removal efficiency for PM2.5. PPM composite nanofiber showed a good removal performance for RhB in solution.

Robust alternating multilayered cellulose nanofiber composite membranes fabricated by high-efficiency calcium ion-precomplexed vacuum-assisted self-assembly towards electromagnetic interference shielding

Robust alternating multilayered cellulose nanofiber composite membranes fabricated by high-efficiency calcium ion-precomplexed vacuum-assisted self-assembly towards electromagnetic interference shielding

Preparation and Characterization of Electrospinning Gelatin Nanofiber Membranes Containing Carvacrol Nanoparticles

AbstractThe purpose of this study was to analyse the potential prospect of electrospinning gelatin nanofiber membranes containing carvacrol nanoparticles (G−Car−NPs−NF) as packaging material in food field. Sustained‐release antioxidant and antibacterial nanofiber membranes were prepared by incorporating the carvacrol nanoparticles (Car−NPs). Carvacrol (Car) was used to form nanoparticles with zein and sodium caseinate, and then electrospinning with gelatin‐based solution to form nanofiber membranes. The biological activities of composite nanofiber membranes were exhibited. The antioxidant capacity was characterized by the scavenging rate of 2,2‐diphenyl‐1‐picrylhydrazyl (DPPH) free radical. With the increase of the concentration of Car, the antioxidant capacity of G−Car−NPs−NF was gradually improved. In addition, G−Car−NPs−NF exhibited inhibitory effect on Escherichia coli (E. coli), Staphylococcus aureus (S. aureus) and Candida albicans (C. albicans) and the inhibitory effect was positively correlated with the concentration. Moreover, the nanofiber membranes showed the slow‐release rate in vitro release and kept the appropriate concentration. These results were directly showed that G−Car−NPs−NF could be used as an effective packaging material for Car in food industry.