Commercial Fused Deposition Modeling Research Articles

FDM technology for the prototyping of polymer stents

Abstract Fused deposition modelling (FDM) technology allows the use of a wide range of thermally processable biocompatible or biodegradable polymers. Biomedical research is currently focusing on the development of 3D printed stents that can be biodegradable, as well as drugeluting. In this proof-of-concept study, a cylindrical substrate was integrated into a commercial FDM printer to establish a process for stent printing. Stents printed on a planar substrate were compared with those printed on the cylindrical substrate. The typical stepped structure along the stent struts on the planar print bed caused by layered printing is avoided with the cylindrical substrate.

Fused Deposition Modeling of Chemically Resistant Microfluidic Chips in Polyvinylidene Fluoride.

Fused deposition modeling (FDM) is well suited for microfluidic prototyping due to its low investment cost and a wide range of accessible materials. Nevertheless, most commercial FDM materials exhibit low chemical and thermal stability. This reduces the scope of applications and limits their use in research and development, especially for on-chip chemical synthesis. In this paper, we present FDM fabrication of microfluidic chips with polyvinylidene fluoride (PVDF) for applications that require high thermal or chemical resistance. Embedded microchannels with a minimum channel width and heights of ~200 µm × 200 µm were fabricated, and the resistance against common solvents was analyzed. A procedure was developed to increase the optical transmission to result in translucent components by printing on glass. Chips for fluid mixing were printed, as well as microreactors that were packed with a catalytically active phase and used for acetal deprotection with a conversion of more than 99%. By expanding the use of fluorinated polymers to FDM printing, previously challenging microfluidic applications will be conducted with ease at the lab scale.

Experimental and theoretical thermal performance analysis of additively manufactured polymer vacuum insulation panels

Vacuum Insulation Panels (VIPs) are characterized by low thermal conductivity, which makes them attractive for applications in buildings, refrigerators, and cold chain logistics. The study of new technologies to manufacture VIPs has grown considerably in recent years. This work presents a feasibility analysis of additive manufacturing technique to manufacture polymer VIPs. The 3D printable multilayered VIPs, in which several interlayers are utilized to suppress gas conduction and thermal radiation, are designed and then manufactured using a commercial fused deposition modeling 3D printer. The effective thermal conductivity of the 3D printed VIPs is evaluated at various vacuum levels (1 atm, 10,000 Pa, 1000 Pa, 100 Pa and 10 Pa) using the standard test method (ASTM C518). Additionally, an analytical model and numerical simulation are performed to analyze heat transfer in these 3D printed VIPs and optimize the VIP design. The experimental results show that an effective thermal conductivity of 0.0155 W/m/K is achieved for the 3D printed VIP with 8 solid interlayers at 10 Pa, which is about 60 % of the thermal conductivity of air at 1 atm pressure. It is also found that there exists an optimal number of interlayers in the multilayered VIPs when its pressure is >1000 Pa. At lower pressures, the effective thermal conductivity of the multilayered VIPs decreases monotonically with increasing number of interlayers. This work is the first one to employ 3D printing techniques to manufacture polymer VIPs, and it is expected to offer a pathway for wider adoptions of VIPs due to its advantage low cost and high manufacturing flexibility.

Numerical and experimental study of attenuation inspection during FDM with ultrasonic leaky waveguide

ABSTRACT This work proposes an ultrasonic leaky waveguide (ULWG) for in-situ structural integrity inspection during fused deposition modeling (FDM). Since the ultrasonic wave propagation speed (m·s−1) is much higher than the deposition speed (mm·s−1), a quasi-static finite element model is first established to simulate the wave propagation during this dynamic process. The amplitude and energy attenuation coefficients (α and ζ) are chosen as the inspection features. Processing parameters including deposition layer thickness and number, inspection frequency, plate thickness and interface impedance are explored. For the first layer printing, a thinner thickness, higher frequency and proper interface impedance will enable a better inspection with high sensitivity. For multilayer printing, the multimodal dispersion curves change continuously and α oscillation is observed due to waveform aliasing that ζ is more reliable. Printing failures such as detachment can be predicted as well from the model established. The ULWG is then integrated into a commercial FDM machine to capture the attenuation coefficients of an “S” shape sample. The poor adhesion, local and global detachments, path planning impact can all be revealed by ζ experimentally. Moreover, being consistent to the simulation, the fluctuation of α in multilayer printing increases, which prevents a further printing evaluation.

Enhancing the strength and toughness of polylactic acid through fused deposition modeling‐induced orientation and nucleation effects of attapulgite

AbstractSimultaneously enhancing strength and toughness through simple and low‐cost methods has always been a challenge for polylactic acid (PLA) materials. In this context, natural attapulgite (ATT) nanorods were used as fillers combined with fused deposition modeling (FDM) to improve the strength and toughness of PLA. The printable PLA nanocomposite filaments filled with ATT nanorods were prepared by melting compounding and smoothly printed via a commercial FDM three‐dimensional (3D) printer. The influences of FDM process and ATT filling on the properties of PLA/ATT composite parts were evaluated through microstructure analysis, rheological, and mechanical tests. The results suggest that PLA/ATT composite parts manufactured by FDM exhibit superior mechanical properties, which can be attributed to the FDM induced orientation and nucleation effect of ATT nanorods. The tensile strength can reach 56 MPa with the addition of 2 wt% ATT at a nozzle temperature of 205°C, increasing by 24% compared to pure PLA. In addition, the fracture elongation of PLA/ATT parts printed by FDM has significantly increased to 26%, which is 924% higher than pure PLA. Furthermore, the filling of ATT significantly improves the storage modulus of composite parts. This work provides a new high‐strength, ultra tough, low‐cost, and printing stable PLA/ATT composite material and forming method, offering a promising avenue for the wider application of PLA and ATT in the future.

Effective, versatile and inexpensive extruder system for direct ink writing of high-viscosity pastes

We offer the possibility of implementing a lab-made extruder for direct ink writing (DIW) into a conventional fused deposition modelling (FDM) 3D printer. The ink extruder was designed to comply with various requirements including the possibility of using multiple syringe volumes, ease of assembly, compatibility with numerous commercial FDM printers, ink retraction and ink flow control and the ability to extrude inks with a wide range of viscosities (ink yield stresses from 135 to 1100 Pa). The load in the extruder was attained by combining a stepper motor and a gear reduction system. The reduction system was connected to a trapezoidal threaded spindle through a rigid coupler. The movement of the spindle was transmitted to the plunger of a syringe that contained the ink (with volumes ranging from 3 to 30 mL), by means of a linear guide system. Most of the extruder parts were printed with the same FDM printer to which the DIW extruder ended attached to. The DIW extruder wiring connections were simply made by using the E-axis connectors available in the FDM printer. Modifications of the FDM printer software required for the correct control of the DIW extruder were also relatively simple, avoiding firmware modification. This simplicity made the two DIW and FDM heads easily interchangeable, thus amplifying the functionality of a conventional FDM printer. The cost of this new DIW extruder is approx. 100€.

Multipotent Mesenchymal Cells Homing and Differentiation on Poly(ε-caprolactone) Blended with 20% Tricalcium Phosphate and Polylactic Acid Incorporating 10% Hydroxyapatite 3D-Printed Scaffolds via a Commercial Fused Deposition Modeling 3D Device.

As highlighted by the 'Global Burden of Disease Study 2019' conducted by the World Health Organization, ensuring fair access to medical care through affordable and targeted treatments remains crucial for an ethical global healthcare system. Given the escalating demand for advanced and urgently needed solutions in regenerative bone procedures, the critical role of biopolymers emerges as a paramount necessity, offering a groundbreaking avenue to address pressing medical needs and revolutionize the landscape of bone regeneration therapies. Polymers emerge as excellent solutions due to their versatility, making them reliable materials for 3D printing. The development and widespread adoption of this technology would impact production costs and enhance access to related healthcare services. For instance, in dentistry, the use of commercial polymers blended with β-tricalcium phosphate (TCP) is driven by the need to print a standardized product with osteoconductive features. However, modernization is required to bridge the gap between biomaterial innovation and the ability to print them through commercial printing devices. Here we showed, for the first time, the metabolic behavior and the lineage commitment of bone marrow-derived multipotent mesenchymal cells (MSCs) on the 3D-printed substrates poly(e-caprolactone) combined with 20% tricalcium phosphate (PCL + 20% β-TCP) and L-polylactic acid (PLLA) combined with 10% hydroxyapatite (PLLA + 10% HA). Although there are limitations in printing additive-enriched polymers with a predictable and short half-life, the tested 3D-printed biomaterials were highly efficient in supporting osteoinductivity. Indeed, considering different temporal sequences, both 3D-printed biomaterials resulted as optimal scaffolds for MSCs' commitment toward mature bone cells. Of interest, PLLA + 10% HA substrates hold the confirmation as the finest material for osteoinduction of MSCs.

A Methodology to Characterize Structurally the Bonding between Two Parts Made of FDM-3D Printed Dissimilar Materials

Fused Deposition Modelling (FDM) is a common technique used when rapid prototyping is needed to perform a preliminary evaluation of the suitability of a part. For this purpose, several materials, as PLA, ABS, PET-G and others, are easily available in the market along with a wide range of commercial 3D printers at affordable prices. Prototypes manufactured under this technique are usually made of a single material and, for most of the applications, it is enough to fulfill the required specifications. However, the increasing demand for the manufacturing of parts made of more than one material suggests that prototyping via FDM using two dissimilar materials should be assessed to assure that such technique is still acceptable to perform a preliminary evaluation of a part. For this purpose, a methodology using a commercial FDM 3D printer is proposed to characterize the flexural and shear bonding behavior of two dissimilar materials. This methodology implements four steps: The selection of the applicable UNE standards as main reference, the design and manufacture of the test specimens based on these standards, the execution of the structural tests to characterize the behavior of those specimens and the analysis of the test data along with the conclusions. This methodology has been validated using ABS and PLA as base materials. The coherence and accuracy of the results obtained from this specific case substantiate that it is a valid methodology to evaluate the structural behavior of the bonding of two dissimilar materials, beyond PLA and ABS, using commercial and affordable off-the-shelf 3D printers.

Property enhancement of 3D printed of timber waste/PLA composite by surface coating

Poly Lactic Acid (PLA) is a biodegradable polymer that is both biocompatible and biodegradable. It is one of the bio-driven polymers. Additive manufacturing has opened up a plethora of new product types and application possibilities. In order to print components and parts, the fused deposition modeling technique makes use of polymer filaments. An experimental investigation was carried out to determine the effects of layer thickness and epoxy resin coating on the mechanical and water absorption capabilities of 3D printed timber waste/PLA composites. The results of the investigation are presented in this paper. The specimens were printed using a commercial Fused Deposition Modelling (FDM) method with layer thicknesses of 0.15 mm, 0.20 mm, and 0.25 mm. The specimens were made of wood waste and PLA composite. It was decided to cover the specimens with Araldite LY556 epoxy resin, with Aradur HY 591 serving as a hardener. Standard ASTM testing procedures were used to evaluate the tensile, impact, and water absorption capabilities of the material. Layer thicknesses of 0.15 mm yield the greatest results in terms of tensile strength and impact resistance. The samples with 0.15 mm layer thicknees provided the best tensile strength of 14.647 MPa, impact strength of 4.952 KJ/mm and 1.813 Wt. % of water absoption. The Araldite LY556 epoxy coating improved the tensile and impact strength of 3D printed specimens of different layer thicknesses and also reduced the water absorption to an appreciable amount. The coating improved the average tensile strength by 25.66% and impact strength by 33.16% and also reduced the water absorption by 89.96%.

Antibacterial Efficacy of Non-Copper Polymer Based Composite Enhanced with Metallic Particles Using Fused Deposition Modeling

The aim of this experimental investigation is to assess the antibacterial resistance of a biodegradable Polylactic acid (PLA) based composite material enriched with non-copper metallic particles, notably Stainless Steel, and Aluminum as alternatives to copper. The composite materials were processed using additive manufacturing technology using commercial fused deposition modeling printers to produce samples for antibacterial testing. The antibacterial materials were assessed according to international standards to evaluate the antibacterial efficacy at different time intervals. It has been disclosed that the biodegradable PLA composite enhanced with Stainless Steel or Aluminum demonstrated an excellent resistance against distinct kinds of bacteria through the observed significant reduction in the bacteria levels.

A simple and fast method for screening production of polymer-ceramic filaments for bone implant printing using commercial fused deposition modelling 3D printers

3D printing is a promising technique for obtaining bone implants. However, 3D printed bone implants, especially those printed using fused deposition modelling, are still in the experimental phase despite decades of work. Research on new materials faces numerous limitations, such as reagents' cost and machines' high prices to produce filaments for 3D printing polymer-ceramic composites for fused deposition modelling. This paper presents a simple, low-cost, and fast method of obtaining polymer-ceramic filaments using apparatus consisting of parts available in a hardware store. The method's versatility for producing the filaments was demonstrated on two different biodegradable polymers – polylactic acid and polycaprolactone – and different concentrations of calcium phosphate – β-tricalcium phosphate – in the composite, up to 50 % by weight. For screening purposes, numerous scaffolds were 3D printed from the obtained filaments on a commercial 3D printer. Structural, mechanical, and biological tests show that the 3D printed scaffolds are suitable for bone implants, as their structure, mechanical, and non-cytotoxic properties are evident. Moreover, the proposed method of composite forming is a simplification of the processes of manufacturing and researching 3D printed materials with potential applications in the regeneration of bone tissue.

Influence of the Feedstock Preparation on the Properties of Highly Filled Alumina Green-Body and Sintered Parts Produced by Fused Deposition of Ceramic

This paper investigates new approaches for the blending and plastification of ceramic powder with a binder to form fused deposition of ceramic (FDC) feedstock. The fabrication of highly filled ceramic filaments was accomplished using the granulation by agitation technique, followed by twin-screw extruder homogenization and single-screw extruder filament extrusion. The feedstocks are based on alumina (Al2O3) powders, which were prepared with an industrial binder through three different routes: wet granulation, melt granulation and melt granulation with a suspension. After printing cubic samples and tensile test specimens on a commercial fused deposition modelling (FDM) printer, the properties of the resulting green-body and sintered parts were investigated. The green-body mechanical values are compared with results from commercially available filaments. Mixing the binder with the alumina powder and surfactant in a suspension produces the lowest viscosity and the best elongation at break.

A Low-Cost Process for Fabricating Reinforced 3D Printing Thermoplastic Filaments.

Low-cost desktop-sized fused deposition modeling (FDM) printers have been widely embraced by small to large-scale institutions and individuals. To further enhance their utility and increase the range of materials that they can process, this work proposes a low-cost solution that adapts to low-cost desktop-sized extruders and enables them to fabricate filaments comprising a wide range of nonorganic reinforcing particles. This solution will fill a gap in the field, as low-cost fabrication techniques for reinforced filaments have been lacking. In the proposed solution, particles are heated and deposited on thermoplastic pellets to form a coating. Coated pellets are subsequently extruded using a low-cost desktop single-screw extruder. The effectiveness of the process is demonstrated by fabricating polylactic acid (PLA) filaments reinforced with two types of reinforcements, namely, dune sand and silicon carbide. Filaments' stiffness and strength were measured, and their microstructure along their lateral and longitudinal directions were investigated. Improvements in tensile strength (up to 8%) and stiffness (up to 4.5%) were observed, but at low reinforcement levels (less than 2 wt%). Results showed that the proposed process could be used to fabricate filaments with multiple types of particles. The produced filaments were successfully used to fabricate 3D parts using a commercial desktop FDM printer.

Utilizing ultrafast lasers for postprocessing to improve mechanical properties of 3D-printed parts

Recent advances in additive manufacturing technologies have already led to the wide-scale adoption of 3D-printed parts in the aerospace, medical, automotive, tooling, and electronics industries. The expansion in choice of materials that can be processed, in particular, using fused deposition modeling (FDM), selective laser sintering/melting, and stereolithography, and the steady advancements in dimensional accuracy control, have extended the range of applications beyond rapid prototyping. However, additive manufacturing still has considerable limitations compared to traditional and subtractive manufacturing processes. This work addresses limitations associated with the as-deposited surface roughness of 3D-printed parts. The effects of roughness-induced stress concentrations on the mechanical strength were studied, and ultrafast laser postprocessing was utilized to reduce the surface roughness of 3D-printed parts. The samples were manufactured using a commercial desktop FDM system and standard ASTM flat dogbone geometries. The samples were then postprocessed with a high-repetition-rate ultrafast Yb-fiber laser using a multi-layer scan approach. This novel postprocessing method enables high-efficiency material removal without inducing excessive thermal residual stresses into the material and, therefore, is suitable for postprocessing thermally sensitive materials, such as PLA and other polymers as well as parts with engineered porosity. In this work, we vary laser process parameters, such as average power and number of laser-processed layers, to achieve various levels of surface roughness. Values of tensile strength of the specimens were compared between 3D-printed samples featuring initial roughness and laser postprocessed samples with different values of surface roughness. The results indicate that the laser-processed samples exhibit an almost 10% increase in tensile strength depending on specific laser processing parameters.

Recycling of waste crab shells into reinforced poly (lactic acid) biocomposites for 3D printing

To promote natural waste resource utilization, a novel biocomposite, composed of waste crab shells and poly (lactic acid) matrix, was developed by combining chemical treatment and 3D printing. A crab shell powder (ISCSP) with an abundant porous structure and a high specific surface area was obtained by treatment with hydrochloric acid and sodium hydroxide. Importantly, under the optimal printing parameters determined by the finite element analysis, test samples, and porous bones were successfully printed using CSP/PLA composites by a commercial fused deposition modeling (FDM) 3D printer. The morphology, mechanical and thermal properties, antibacterial properties, and biocompatibility of the CSP/PLA composites were then assessed. Our results revealed that the tensile strength and flexural strength of the ISCSP/PLA composites reached 58.71 and 90.11 MPa, which were 28.6 % and 28.8 % higher than that of pure PLA, respectively. The glass transition and melting temperatures of the composites remained similar to those of pure PLA. Interestingly, the addition of CSP increased PLA crystallinity, which could be attributed to the nucleation effect of CSP in the system. The antibacterial activity of the PLA-1.5ESCSP composite samples against Escherichia coli (E. coli) was greater than 99 %. More importantly, the live/dead assay showed that the CSP/PLA composites possessed excellent biocompatibility. Therefore, the developed CSP/PLA biocomposites are potential feedstocks for 3D printing in bone tissue engineering and may be used as graft substitutes in reparative and reconstructive surgery. They are especially beneficial due to their superior mechanical and thermal properties, excellent antibacterial activities, and significant biocompatibility.

Melt electrowriting of PLA, PCL, and composite PLA/PCL scaffolds for tissue engineering application

Fabrication of well-ordered and bio-mimetic scaffolds is one of the most important research lines in tissue engineering. Different techniques have been utilized to achieve this goal, however, each method has its own disadvantages. Recently, melt electrowriting (MEW) as a technique for fabrication of well-organized scaffolds has attracted the researchers’ attention due to simultaneous use of principles of additive manufacturing and electrohydrodynamic phenomena. In previous research studies, polycaprolactone (PCL) has been mostly used in MEW process. PCL is a biocompatible polymer with characteristics that make it easy to fabricate well-arranged structures using MEW device. However, the mechanical properties of PCL are not favorable for applications like bone tissue engineering. Furthermore, it is of vital importance to demonstrate the capability of MEW technique for processing a broad range of polymers. To address aforementioned problems, in this study, three ten-layered box-structured well-ordered scaffolds, including neat PLA, neat PCL, and PLA/PCL composite are fabricated using an MEW device. Printing of the composite PLA/PCL scaffold using the MEW device is conducted in this study for the first time. The MEW device used in this study is a commercial fused deposition modeling (FDM) 3D printer which with some changes in its setup and configuration becomes prepared for being used as an MEW device. Since in most of previous studies, a setup has been designed and built for MEW process, the use of the FDM device can be considered as one of the novelties of this research. The printing parameters are adjusted in a way that scaffolds with nearly equal pore sizes in the range of 140 µm to 150 µm are fabricated. However, PCL fibers are mostly narrower (diameters in the range of 5 µm to 15 µm) than PLA fibers with diameters between 15 and 25 µm. Unlike the MEW process of PCL, accurate positioning of PLA fibers is difficult which can be due to higher viscosity of PLA melt compared to PCL melt. The printed composite PLA/PCL scaffold possesses a well-ordered box structure with improved mechanical properties and cell-scaffold interactions compared to both neat PLA and PCL scaffolds. Besides, the composite scaffold exhibits a higher swelling ratio than the neat PCL scaffold which can be related to the presence of less hydrophobic PLA fibers. This scaffold demonstrates an anisotropic behavior during uniaxial tensile test in which its Young’s modulus, ultimate tensile stress, and strain to failure all depend on the direction of the applied tensile force. This anisotropy makes the composite PLA/PCL scaffold an exciting candidate for applications in heart tissue engineering. The results of in-vitro cell viability test using L929 mouse murine fibroblast and human umbilical vein endothelial (HUVEC) cells demonstrate that all of the printed scaffolds are biocompatible. In particular, the composite scaffold presents the highest cell viability value among the fabricated scaffolds. All in all, the composite PLA/PCL scaffold shows that it can be a promising substitution for neat PCL scaffold used in previous MEW studies.

Effect of the manufacturing parameters on the tensile and fracture properties of FDM 3D-printed PLA specimens

Fused Deposition Modeling (FDM), also known as material extrusion, is currently one of the most popular Additive Manufacturing (AM) technology on the market. In this study, two commercial FDM printers (Prusa i3 MK3 and WN400 3D Platform) were used for layer-by-layer manufacturing of polylactic acid (PLA) Dog Bone (DB) and Single Edge Notched Bend (SENB) specimens, aimed at investigating the influence of the manufacturing parameters on the tensile and fracture properties of PLA elements obtained by FDM technology. The effects of growing direction (horizontal and vertical), building orientation (0°, 45° and 90°), printer type, layer thickness (0.15 and 0.40 mm), specimen thickness (4 and 10 mm) and filament color (purple, white, black, gray, red, orange) are discussed in detail. Tensile tests were performed on DB specimens, while fracture mechanics tests on SENB specimens. Both the tensile and fracture properties of FDM 3D-printed PLA specimens have been found to be dependent on the investigated manufacturing parameters. From the microstructural analyses of the SENB fracture surfaces, it has been observed that the fracture mechanisms and crack propagation is a step-wise process. Finally, the material properties charts (Young’s modulus and mode I fracture toughness versus tensile strength) are plotted.

Characterization and Sustainability Potential of Recycling 3D-Printed Nylon Composite Wastes

The revolution of 3D-printing technology has caused an additional source of plastic waste, especially the new generation of composite filaments that are linked with the commercial fused deposition modeling process, adding pressure to find a sustainable solution to tackle the emerging waste problem. This study aims to investigate the mechanical and thermal properties of a blended recycled composite material produced by mixing two different 3D-printed reinforced composite wastes, carbon fiber CF/nylon, and glass fiber GF/nylon filaments that were mixed at different percentages using a hot extrusion procedure, tested by a tensile testing machine, and processed with five different weight ratios to study the impact of blend ratios on the material characteristics of the recycled composites and to find the optimum weight ratios with the most preferred properties. The results revealed that the maximum tensile strength of the GF/nylon composite was achieved with 60 wt%. The highest elastic modulus value was recorded at 60 wt% GF/nylon. Moreover, it was noted that at 80 wt% of GF/nylon, the ductility is at the peak value among the composites.

Flexible PBAT-Based Composite Filaments for Tunable FDM 3D Printing.

Biobased composites with peculiar properties offer an attractive route for producing environmentally friendly materials. The reinforcement for poly(butylene adipate-co-terephthalate) (PBAT), based on zein-titanium dioxide (TiO2) complex (ZTC) microparticles, is presented and used to produce composite filaments, successfully 3-dimensionally (3D) printed by fused deposition modeling (FDM). The outcome of ZTC addition, ranging from 5 to 40 wt %, on the thermo-mechanical properties of composite materials was analyzed. Results reveal that storage modulus increased with increasing the ZTC content, leading to a slight increase in the glass transition temperature. The creep compliance varies with the ZTC concentration, denoting a better resistance to deformation under constant stress conditions for composites with higher complex content. Scanning electron microscopy was used to assess the quality of interphase adhesion between PBAT and ZTC, showing good dispersion and distribution of complex microparticles in the polymer matrix. Infrared spectroscopy confirmed the formation of a valid interface due to the formation of hydrogen bonds between filler and polymer matrix. Preliminary tests on the biocompatibility of these materials were also performed, showing no cytotoxic effects on cell viability. Finally, the 3D printability of biobased composites was demonstrated by realizing complex structures with a commercial FDM printer.

Effect of FDM infill patterns on mechanical properties

One of the advantage of additive manufacturing technologies is the possibility to produce hollow section products, which are lighter, cheaper, faster to create and still they can have the required mechanical properties. Most of the times a 3D printed part's most important feature is the freedom of shape, and by setting the appropriate infill we can ensure the proper resilience as well. In this paper the different infill patterns and volume related percentages are compared by using the commercial Fused Deposition Modelling (FDM) technology. For the investigation non-standardized bending test were made with two loading orientation. From the results, the relation between the mass of the product and manufacturing time can be stated clearly, the pattern and percentage, as well as the decrease of the resilience in case the use of hollow areas in products.