Coated Cotton Fabrics Research Articles

A sustainable approach for the simultaneous removal of cationic and anionic dyes from waste water using multilayer MWCNT, UMCNO, and PVA coated cotton fabrics

A sustainable approach for the simultaneous removal of cationic and anionic dyes from waste water using multilayer MWCNT, UMCNO, and PVA coated cotton fabrics

Anti-flammable, anti-fouling, anti-bacterial treatment of cotton fabrics with MOF-based hybrid coatings for highly efficient oil-water separation

A flame-retardant and hydrophobic coating was deposited on the surface of the cotton fabric via a two-step spray deposition technique. Specifically, the coating was composed of flame retardant components (guanidine phosphate) and hydrophobic species (Ti-MOF and bis(3-aminopropyl)-terminated poly(dimethylsiloxane) (PDMS)) and crosslinked with glutaraldehyde. The limiting oxygen index (LOI) of the coated cotton fabrics increased from 18.0 % to 32.0 % (15#) and 26.5 % (15#-Ti-PDMS) relative to that of the original cotton fabric, and the coated cotton fabrics also self-extinguished in the UL-94 flammability test. Compared with that of the original cotton fabric, the PHRR of the coated fabrics was significantly lower, reaching 80 %. The coated cotton fabrics (15# and 15#-Ti-PDMS) had good antibacterial properties against Staphylococcus aureus (S. aureus). In addition, 15#-Ti-PDMS had high hydrophobicity, good washing and abrasion resistance and good water-oil separation performance. Its water contact angle was 146°. The water contact angle remained above 130° after 10 laundering cycles and 50 scratch cycles. Even under strongly acidic and basic conditions, the water-oil separation efficiency of 15#-Ti-PDMS was greater than 99 %, and it was still greater than 90 % after 10 cycles. Therefore, a simple and effective method for preparing flame-retardant, hydrophobic and antibacterial cotton fabrics was developed.

Sustainable furfural bis-thymol based benzoxazines: Superhydrophobic, aggregation induced emission and corrosion resistant properties

Sustainable bis-thymol based benzoxazines have been synthesized using furfural bis-thymol (FBT) and paraformaldehyde separately with five different fluorine substituted amines through Mannich condensation process. The molecular structure of the obtained benzoxazines has been verified using spectroscopic analyses. The curing temperature of the synthesized benzoxazines are ranged between 241°C and 277°C. Among the synthesized polybenzoxazines, poly(FBT-pfa) exhibits the highest thermal stability of 52% char yield. All the polybenzoxazines exhibit the value of LOI above the threshold limit of 26 which infers the self-extinguishing property of the polymer. Poly(FBT-pfsa) showed the highest value of water contact angle of 151o, which ascertains that the increased fluorine content contributes to the superhydrophobic nature. Results from hydrophobic durability studies with poly(FBT-pfsa) using coated cotton fabric under acidic and basic conditions indicate its suitability for hydrophobic applications. The corrosion protection ability of polybenzoxazines towards mild steel surfaces was studied and the results obtained suggest that these polybenzoxazines can be used as an excellent coating material. UV-Visible and fluorescence spectroscopic analyses infer that these benzoxazines exhibit aggregation induced emission (AIE) characteristics. Data from different studies suggest that these materials can be conveniently utilized in the form of optical, superhydrophobic and corrosion-resistant coatings.

Evaluation of optical, thermal and hydrophobic properties of sustainable stilbene-based benzoxazines for high-performance utilization

Currently there is a growing interest in the field of photosensitive benzoxazines synthesized from sustainable raw materials. An attempt has been made to synthesize nine structurally different benzoxazines through Mannich condensation reaction. The formation of the expected structure of the synthesized benzoxazine monomers were ascertained using spectroscopic methods. The ring-opening polymerization of benzoxazines was studied using DSC and found that THS-imp benzoxazine monomer exhibits the lowest value of curing temperature (Tp) of 179oC than the rest of the benzoxazine monomers. Thermal stability of polybenzoxazines were analyzed using thermogravimetric analyzer. Among the different polybenzoxazines studied, poly(THS-a) possesses the higher thermal stability with char yield of 53% than that of other benzoxazines. The band gap values of benzoxazines calculated from optical studies are ranged between 3.92-4.71 eV. The hydrophobic behavior of the polybenzoxazines assessed using the water contact angle obtained from goniometer for both neat polymer matrix and benzoxazine coated cotton fabric. Results from the water contact angle infer that the benzoxazines coated cotton fabric exhibited 152o, which shows the superhydrophobic behavior. The corrosion resistant properties of all the polybenzoxazines coated over MS specimen has been tested. Among them poly(THS-pfsa) and poly(THS-imp) have higher Icorr value and corrosion inhibition efficiency of 99%. Data obtained from different studies indicate that the benzoxazines developed from sustainable stilbene can be utilized in the form of coatings, adhesives, sealants, and matrices for composites for wide range of industrial and engineering applications, where high thermal stability and are required.

Antibacterial and wound healing activity of non-thermal plasma treated and MXene (Ti3C2TX)/ WO3 coated cotton fabrics

In this study, MXene (Ti3C2Tx)/WO3 nanocomposite was directly deposited on the surface of non-thermal plasma treated cotton fabrics. Initially, argon was used as a plasma forming gas to treat the surface of cotton fabrics. Subsequently, the MXene (Ti3C2Tx)/WO3 nanocomposite was deposited on the surface of non-thermal plasma treated cotton fabrics by co-precipitation method. As prepared cotton fabrics were characterized by various characterization techniques that includes, X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Field emission scanning electron microscopy (FESEM) with energy-dispersive X-ray (EDX) analysis, and Contact Angle (CA) measurement. SEM and FTIR analysis confirmed the presence of MXene (Ti3C2Tx)/WO3 nanocomposite on the surface of cotton fabrics. In addition, contact angle analysis unveiled the super hydrophilic nature of cotton fabrics after surface modification. The antibacterial activity and the wound healing assay of the untreated and surface modified cotton fabrics were examined by in vitro analysis. Results unveiled that the surface modified cotton fabrics showed excellent antibacterial activity against gram-negative bacteria (Escherichia coli) and gram-positive bacteria (Staphylococcus aureus) and substantial wound healing activity. From this investigation it is inferred that plasma treated and nanocomposite functionalised cotton fabrics have the potential to be employed as wound dressing material.

Polyelectrolyte Complex Coated Cotton Fabrics with Hydrophobicity, Antibacterial Activity, and Flame Retardancy

AbstractCotton fabrics with the main constituent of cellulose, which is hydrophilic, bacterial infected, and flammable, are in urgent need of functionalization as a kind of widely applied material. To address these issues, in this work, modified polyelectrolyte complex (MPEC) coatings with polyethylenimine (PEI), polyphosphate (APP), and perfluorodecyltrichlorosilane modified PEI (PFTS‐PEI) are prepared to construct multi‐functionally gradient MPEC coatings on cotton fabrics. Stability and synergistic effects on hydrophobicity, antibacterial activity, and flame retardancy in this system have been studied. Notably, PFTS‐PEI with fluorine and silicone elements are confirmed to provide hydrophobicity and durability for MPEC coatings, which not only has no negative effect on other functions but also makes some improvement in antibacterial activity. This MPEC‐treated cotton fabric finally has an antibacterial rate against S. aureus and E. coli of 99.9% and 96.9%, limiting oxygen index of 28.5% and water contact angle of 118°, which can be almost maintained after 20 times washing. The modified PEC will provide an efficient strategy to achieve durable multi‐functions on cellulose‐based fabrics.

Sericin-TiO2 nanocomposite treated cotton fabrics for enhanced antibacterial and self-cleaning properties

The valorization of industrial byproducts is rising as a new dawn and has become a creative area of research for the scientists. Sericin is being a good resource of starting materials since it can be recovered and recycled. The research aimed to modify cotton fabric by sericin-TiO2 nanocomposite (STNc) for enhancement its antibacterial and self-cleaning properties. STNc were prepared using tetraisopropylorthotitanate (TIOT) and sericin with proportions 2:1, 2:2 and 1:2. The obtained STNc possesses anatase phase of TiO2 nanoparticles having an average 22.9 nm particle sizes. The STNc coated cotton samples were prepared with three different weight fractions of STNc and citric acid (2:1:2, 2:2:1 and 1:2:2). The incorporation of STNc onto cotton fabric was examined by FTIR spectroscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) analyses. The antibacterial activity of STNc coated cotton fabrics was investigated against drug resistant bacterium viz. Staphylococcus aureus, Pseudomonas 4A and Escherichia coli. The STNc coated cotton fabric exhibited effective resistance against Escherichia coli and Staphylococcus aureus. The antibacterial properties of STNc coated cotton fabrics were depended with the fraction of STNc. The uncoated and STNc coated cotton fabrics were stained with coffee and then irradiated on sunlight for 0, 30, 60, 90 h and UV light for 2, 4, 6, 8, 10 h. A noticeable decrease in the coffee stain's appearance was observed after 90 h sunlight and 10 h UV light exposure for STNc coated cotton fabric. The reusability of photo exposed samples was evaluated by FTIR spectroscopy.

Influence of curing temperature on shape memory performance of polyethylenimine‐based shape memory polymer coated cotton fabric

AbstractThis research investigates the effect of curing temperature on the shape memory behavior and coating adhesion of polyethylenimine‐based shape memory polyurethane (PEI‐SMPU) to cotton fabric. The study utilized a dip‐coating process to apply a PEI‐SMPU solution to cotton fabrics, followed by curing at temperatures ranging from 100 to 160°C. Scanning electron microscopy confirmed uniform coating, and significant adhesion, and surface roughness was substantially reduced as evidenced by atomic force microscopy. The fabric's shape memory performance improved with increasing cure temperature, exhibiting excellent recovery (90%) at lower SMPU concentrations (1%). The results indicated that the tear strength of the fabric decreased with increasing curing temperature, attributed to constrained yarn mobility due to increased SMPU cross‐linking. The study successfully correlates the thermal and mechanical properties of SMPU‐coated fabrics with the interaction between SMPU and fabric, emphasizing the preservation of their laundering durability after multiple wash cycles. These findings contribute to the development of smart textiles with improved performance and longevity.

Antimicrobial coating of biologically synthesized silver nanoparticles on surgical fabric and surgical blade to prevent nosocomial infections

In this study, biologically synthesized AgNPs were found to be effective against six hospital prevalent bacterial species (Pseudomonas aeruginosa, Escherichia coli, Acinetobacter baumannii, Klebsiella pneumoniae, Methicillin-resistant Staphylococcus aureus and Enterococcus faecalis). AgNPs were deposited on the fabric and surgical blades using layer-by-layer and electrochemical deposition methods, respectively. The coated objects were characterized using scanning electron microscopy, X-ray diffraction and Fourier transform infrared spectroscopy and energy dispersive X-ray. Coated fabric samples and blades when tested against six above mentioned bacterial species were found to be effective for all of them. Antibiofilm activity of AgNPs coated blade and fabric was tested against P. aeruginosa and SEM images of post-treated fabrics and blades showed clear bacterial cell distortion and inhibition. Furthermore, washing durability test revealed that AgNPs were strongly attached to the surface of fabric even after 20 cycles of hospital laundering. This unlocks the way to several technologically relevant applications of AgNPs coated surfaces to reduce the risks of nosocomial infections and as a proof of concept; we demonstrated efficient antibacterial properties of AgNPs coated cotton fabric and surgical blades.

Eco-friendly activation of cotton textiles with LiNbO3 nanoparticles for enhanced self-cleaning and antibacterial performance

Cotton textiles play a universal role in everyday life, but they are prone to stain and serve as a primary channel for transmitting viruses and bacteria. The photocatalytic/antibacterial coatings are highly effective in addressing bacterial contamination on fabrics, although their efficacy diminishes with continuous use and washing. Here, insights are provided into the attachment of LiNbO3 on cotton surfaces using eco-friendly chemical activators to promote resistance to washing cycles, self-cleaning, and bactericide textiles. LiNbO3 nanoparticles were synthesized by low-temperature hydrothermal synthesis and directly applied to cotton fabric using immersion. The synthesized nanoparticles were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) N2 adsorption, diffuse reflectance for band gap determination, and Raman spectroscopy. A simple and effective impregnation method was used, promoting an ester-bond attachment between the cotton surface and the activators. Microscopy analysis (SEM) confirmed the successful deposition of the nanoparticles on cotton fabric. The LiNbO3 coating consisted of transparent layers and did not change the properties of cotton. Methylene blue stains are generally eliminated under UV light after 2 h using nanoparticles and activators. Antibacterial properties were evaluated under visible light through direct contact with bacterial suspensions and culturing. The coated cotton fabric that was activated with oxalic acid exhibited significant photocatalytic antibacterial activity against both Escherichia coli (gram-negative) and Staphylococcus aureus (gram-positive) bacteria, with bacterial reduction rate above 97 %, even after 10 washing cycles. This performance can be attributed to the effective coupling of LiNbO3 with oxalic acid in the cotton’s surface and its resistance to washing out. This study's novel synthesis and coating method offers an environmentally friendly, cost-effective, and straightforward approach for producing LiNbO3 self-cleaning and antibacterial surface-activated cotton.

Biodegradable poly(lactic acid) blocked polyurethane/carbon nanotubes coated cotton fabric prepared by ultrasonic-assisted inkjet printing for high performance strain sensors

In order to fulfill the demands for degradability, a broad working range, and heightened sensitivity in flexible sensors, biodegradable polyurethane (BTPU) was synthesized and combined with CNTs to produce BTPU/CNTs coated cotton fabric using an ultrasonic-assisted inkjet printing process. The synthesized BTPU displayed a capacity for degradation in a phosphate buffered saline solution, resulting in a weight loss of 25 % after 12 weeks of degradation. The BTPU/CNTs coated cotton fabric sensor achieved an extensive strain sensing range of 0–137.5 %, characterized by high linearity and a notable sensitivity (gauge factor (GF) of 126.8). Notably, it demonstrated a low strain detection limit (1 %), rapid response (within 280 ms), and robust durability, enabling precise monitoring of both large and subtle human body movements such as finger, wrist, neck, and knee bending, as well as swallowing. Moreover, the BTPU/CNTs coated cotton fabric exhibited favorable biocompatibility with human epidermis, enabling potential applications as wearable skin-contact sensors. This work provides insight into the development of degradable and high sensing performance sensors suitable for applications in electronic skins and health monitoring devices.

Long-chain alkyl groups enhance the water-repellent properties of short-chain perfluoroalkyl compounds: An experimental and computer simulation study

The polymers composed of long-chain stearyl acrylate (SA) and short-chain (perfluorohexyl) ethyl methacrylate (FA) were synthesized using the emulsion polymerization technique. Cotton fabric was then coated with these polymers to act as a water-repellent agent. Surface wetting properties of the coated cotton fabric were tested. In a peculiar manner, the water repellency of the coatings did not improve with the increase of the perfluorohexyl group. Therefore, the polymer's crystallization behaviors and melting temperature were assessed through differential scanning calorimetry (DSC) and computer simulation. A computer simulation was employed to analyze the density, surface energy, element distribution, chain arrangement, bond order parameter, and surface images of the polymer film. The results suggest that water repellency is not directly related to the film's surface energy but rather depends on the element proportion, bond angle distribution, and dihedral angle torsion energy. The key points will serve as invaluable indicators for the development of a highly efficient water-repellent coating with a low proportion of fluorine and provide a more sustainable solution for water-repellent applications.

Thermal stability and flame retardancy of cotton fabric coated with PVA-boric acid-cellulose nanofiber hybrid: Role of chemical interactions

An ecofriendly, polymer coating to impart fire retardancy to cotton fabric is introduced in the current study. Polyvinyl alcohol-boric acid-cellulose nanofiber (PVA-BA-CNF) hybrid coating with different compositions of boric acid and 2.5 wt% cellulose nanofiber (CNF) were coated over cotton fabric. The CNF used in the study was extracted from onion skin, an agricultural waste. The nanofibrous morphology of extracted CNF was confirmed from Transmission Electron Microscopic (TEM) images. The surface morphology of treated cotton was compared with that of bare cotton using scanning electron microscope (SEM) and optical microscope (OM). The dispersion of the coating formulation over the cotton fabric and the porosity after coating were confirmed. Chemical interactions developed in the coating formulations were characterized by Fourier transform infrared spectroscopy (FTIR). In addition to hydrogen bonding established between the coating formulation and cotton fabric, the existence of chemical bonding (B-O-C) between the components of the coating formulation and between the crosslinked coating and cotton fabric has been evident. The thermal stability of the coated cotton fabrics was evaluated using thermogravimetric analysis (TGA). The high char residue recorded for PVA-BA-CNF coated fabric, especially with 17phr BA content indicated the efficiency of crosslinked coating matrix in enhancing the thermal stability of the cotton fabric. The coated cotton degraded in two stages and with a different degradation kinetics than that of uncoated cotton fabric. Flame retardant performance of the coated fabric has been evaluated by vertical flammability tests and pyrolysis combustion flow calorimetry (PCFC). The peak temperature of heat release rate (pHRR) showed 32 % reduction for PVA-BA-CNF coating with 17phr BA content compared with pure cotton indicating a decreasing flame spreading rate due to the inhibition of oxygen diffusion by chemically crosslinked PVA-BA-CNF coating.

Flame retardant cotton fabrics with ultra-fast and long-term fire early warning response

Smart textiles with flame retardant and fire-warning functions have received more and more attention. However, improving the fire-warning response sensitivity and long-term responsiveness of the smart textiles is a top priority. In this research, flame retardant and fire-warning cotton fabrics were prepared by layer-by-layer assembly composite coating consisting of bio-based flame retardants composed of chitosan (CS) and phytic acid (PA) and carbon-based nanomaterials composed of carbon nanotubes (CNTs) and graphene oxide (GO). The PA-GO/CS-CNTs coated cotton fabric showed excellent flame retardancy with a limiting oxygen index (LOI) value of 31 %, and the coated fabrics could self-extinguish rapidly when the flame was removed. The fire hazard of the coated fabric was significantly reduced by reducing the 45.77 % of peak heat release rate, 29.69 % of total heat release and 81.9 % of total smoke production. The PA-GO/CS-CNTs coated cotton fabric showed ultra-fast fire warning response with the response time of 1.0 s. And the fire-warning response time of the coated cotton fabric could last longer than 600 s revealing it possessed the continuous fire warning response property. This research provides a new strategy to prepare the smart fireproof textiles with flame retardant and fire-warning functions to broaden its application in early fire-warning.

Innovative coating of cotton textile fabrics for integrating outstanding flame hazard safety, UV protection, tensile strength strengthening and antibacterial properties

A rational green synthesis method was developed to produce sustainable nanocoatings for cotton fabrics that are flame retardant, strengthened, antibacterial, and UV protective. The nanocoatings were created using silica nanoparticles with an average size of 73.2 nm derived from rice husk (RH-SNP). These nanoparticles were adorned with ZnONPs with an average size of 7.6 nm, which were reduced and capped with molokhia extract made from molokhia stems by-products. The ultimate nanocomposite was evenly distributed in a chitosan solution using ultrasonication. The mass ratio of RH-SNP in the nanocoating was adjusted and fine-tuned for optimization. The coated cotton fabrics were analyzed using spectroscopic and microscopic techniques. The flammability of cotton fabrics treated with sustainable coatings was assessed. The coated fabrics exhibited significantly greater flame retardancy, achieving a zero burning rate compared to 110 mm/min for the untreated one. The enhanced flame-retardant properties were a result of the combined flame-retardant effects of RH-SNP and molokhia stem extract, along with decorated ZnONPs, which created a more robust protective char layer. The coated cotton's antibacterial characteristics showed significant inhibition of bacterial growth, resulting in a 10 mm distinct inhibition zone, while pure cotton had no inhibition zone. Additionally, the coated cotton fabrics had exceptional UV shielding properties with a UPF rating of 167.8, which was more than fourth the value of the uncoated fabric. The tensile strength and elongation of the cotton fabrics were enhanced after applying a sustainable nanocoating, indicating a beneficial effect on tensile strength. Furthermore, the coated fabrics exhibited exceptional durability characteristics.

Construction of efficient and environmentally friendly bio-based flame retardant cotton fabric through layer by layer self-assembly of alkylammonium functional silsesquioxane/phosphorylated sodium alginate

As an important source of green cleaning flame retardants, bio-based materials have been widely studied by researchers. However, the development of efficient biobased flame retardants and convenient finishing methods was of great significance for the functional finishing of materials. Herein, a convenient and efficient flame retardant cotton fabric was prepared via layer by layer self-assembly (LbL) by alternating precipitation of a novel bio-based flame retardant phosphorylated sodium alginate (PSA) and alkylammonium functionalized siloxane (A-POSS). The effect of coating number on flame retardancy and thermal properties of coated cotton fabric was systematically studied. Thermogravimetric analysis (TGA) results showed that residual char contents of AP/PS-15BL under air and N2 atmospheres increased by 252.0% and 225.2%, respectively, compared with control cotton. In vertical flammability tests, both the AP/PS-10BL and AP/PS-15BL showed self-extinguishing behavior and successfully passed the UL-94 V-0 rating. More importantly, the LOI value of AP/PS-15BL was significantly increased to 35.0% from 20.0% of pure cotton fabric. Additionally, coated samples showed good mechanical properties and washable resistance. In CONE test, the peak heat release rate (PHRR) and total heat release rate (THR) of AP/PS-15BL decreased by 89.3% and 49.3% respectively, compared with control cotton. Therefore, this green and convenient flame-retardant finishing method has great application potential in the multi-functional finishing of cotton fabrics.

A multifunctional Ag NPs/guar gum hydrogel as versatile platform for catalysts, antibacterial agents, and construction of oil-water separation interfaces

The frequently encountered wastewater contaminations, including soluble aromatic compound and dye pollutants, pathogenic bacteria, and insoluble oils, have resulted in significant environmental and human health issues. It poses a challenge to utilize identical materials for the treatment of complex wastewater. Herein, in this research, multifunctional Ag NPs/guar gum hybrid hydrogels were fabricated using a facile in situ reduction and self-crosslinking method for efficient remediation of complex wastewater. The Ag NPs/guar gum hybrid hydrogel showed remarkable remodeling, adhesive, and self-healing characteristics, which was favorable for its versatile applications. The combination of Ag NPs with the guar gum skeleton endowed the hybrid hydrogel with exceptional catalytic activity for reducing aromatic compounds and dye pollutants, as well as remarkable antibacterial efficacy against pathogenic bacteria. In addition, the Ag NPs/guar gum hybrid hydrogel could be employed to coat a variety of substrates, including cotton fabrics and stainless steel meshes. The hydrogel coated cotton fabrics and meshes presented superhydrophilicity/underwater superoleophobicity, excellent antifouling capacity, and outstanding recyclability, which could be successfully applied for efficient separation of oil-water mixtures. The findings of this work provide a feasible and cost-effective approach for the remediation of intricate wastewater.

Structure-property relationship of polyhedral oligomeric silsesquioxanes/polydimethylsiloxane superhydrophobic coatings for cotton fabrics

Cotton fabrics are extensively utilized in daily life due to striking advantages such as softness, breathability, skin-friendliness, and cheapness. However, they are susceptible to being contaminated owing to inherent amphiphilicity, severely affecting service lifespan and aesthetic perception. To address this issue, three distinct types of the POSS/PDMS composite coatings are explored, and applied to cotton fabrics, respectively. Subsequently, the correlations between structures of POSS and properties of the composite coatings on the modified cotton fabrics are discussed. The results show that the three types of the POSS/PDMS composite coatings impart the modified fabrics with robust superhydrophobicity even in harsh environments including mechanical damage, chemical corrosion and UV-irradiation. Notably, the damaged POSS/PDMS composite coatings on cotton fabrics can exhibit excellent superhydrophobic self-healing capability by simple heating. Meanwhile, the modified fabrics also show excellent performances in self-cleaning, anti-fouling, anti-icing and oil-water separation applications. Additionally, due to multifunctional groups of MTPOSS, the cotton fabric treated by the MTPOSS/PDMS composite coating exhibits more excellent thermal, mechanical, and UV protection properties without significantly compromising its air permeability as compared to those of the other coated cotton fabrics. This work will pave the way to exploitation and applications of novel multifunctional textiles.

Preparation and properties of flame retardant and hydrophobic cotton fabrics based on poly-(dimethylsiloxane-co-diphenylsiloxane, dihydroxy terminated)/ammonia phytate

Applications for cotton fabrics with multifunctional qualities, such as flame retardancy, hydrophobicity, and anti-ultraviolet properties, are increasingly common and growing daily. The primary objective of this study is to investigate the preparation of flame retardant, hydrophobic, and ultraviolet (UV) protection cotton fabrics through the utilization of Poly-dimethylsiloxane-co-diphenylsiloxane, dihydroxy terminated (HTDMS) and ammonia phytate (AP). The flame retardancy, thermal stability, mechanical properties, anti-UV properties, air permeability and the hydrophobicity properties of coated cotton fabrics were evaluated. The results indicated that the HTDMS/AP coating was successfully deposited on the surface of cotton fabrics. The damaged length of Cotton/HTDMS/AP was 4.7 cm, and the limiting oxygen index reached 31.5 %. The thermogravimetric analysis revealed that the char residues in the high-temperature range were increased. Furthermore, cone calorimetry results indicated that after the HTDMS/AP coating, the peak heat release rate, total heat release, and total smoke production values decreased by 88.7 %, 51.2 %, and 98.4 %, respectively. Moreover, the deposition of HTDMS/AP provided cotton fabrics with hydrophobicity with a water contact angle of over 130°, while Cotton/HTDMS/AP maintained their air permeability, and enhanced the breaking force compared with those of Cotton/AP. Such desirable qualities make HTDMS/AP a meaningful coating for producing multifunctional cotton fabrics.

Multifunctional ammonium polyphosphate coated cotton fabric for flame retardant, anti-wrinkle, ultraviolet protection and anti-bacterial

The multifunctional cotton fabrics, which were expected to become one of the most promising textile materials, gained much attention in the apparel market. In this work, the simultaneous coloration and finishing processes with natural dye were carried out to prepare the multifunctional cotton fabrics. The modification process using ammonium polyphosphate (APP) imparted the cotton fabric with numerous anionic sites along with flame retardant and anti-wrinkle properties. Subsequently, the implementation of coloration with berberine was to render the cotton fabric with elegant shade and anti-bacterial, ultraviolet (UV) protection performances. The obtained results revealed that the cotton fabric treated with APP could obtain deep shade. It was found that the limited oxygen index (LOI), wrinkle recovery angle (WRA), ultraviolet protection factor (UPF) and antibacterial efficiency of treated fabric were 46.4%, 252°, 193 and 99%, respectively. More importantly, the repeated laundering showed negligible influence on the flame retardant and anti-wrinkle performances. In addition, the anti-bacterial and UV protection performance of treated cotton fabric exhibited a slight decline even after 20 cycles of washing. Finally, the washing and rubbing fastness of obtained cotton fabric were also desirable.