Cladding-pumped Ytterbium-doped Fiber Research Articles

1.3 kW Continuous Wave Output Power of Ytterbium-Doped Large-Core Fiber Laser

A very efficient key cladding-pumped trivalent ytterbium (Yb3+) doped fiber laser has been developed. The whole fiber laser system generated 1.3 kW of continuous-wave (CW) maximum output power with very high efficiency at 1.1 μm and near the diffraction beam quality (M2 = 1.27). The measure slop efficiency is 76% and shows no limit of temperature and nonlinear effects. In a preliminary proof of principle study, efficient single-mode operation of a cladding-pumped ytterbium-doped fiber laser with a diameter core and a numerical aperture of 0.09 has been demonstrated. When pumped to the ends of both fibers, they have strong beam quality and display no signs of rolling over even at the highest output power. The large core ytterbium doped fiber laser (YDFL’s) is end pumped with diodes stack source through opposite ends of fiber. This design of fiber can delivers maximum output power which is restricted mostly by accessible pump power.

High SNR Watt-Level Single Frequency Yb-Doped Fiber Laser Based on a Saturable Absorber Filter in a Cladding-Pumped Ring Cavity

A single frequency ring fiber laser is reported based on a cladding-pumped ytterbium-doped fiber (YDF). A medium concentration polarization maintaining (PM) YDF is utilized in ring cavity as a saturable absorber that acts as an ultranarrow bandwidth filter. Here, by making use of double-clad and PM fibers in the cavity configuration, thermal noises are notably damped and the frequency instability is minimized due to the temperature fluctuation and polarization variation. The laser yields up to 35 mW of a stable single longitudinal mode output at 1079.68 nm, whereas the corresponding linewidth is estimated less than 6 kHz. Subsequently, a fiber amplifier is employed to boost up power to 5.21 W with the slope efficiency of 45.6%. The amplifier steadily operates below the stimulated Brillouin scattering threshold power. The signal-to-noise ratio is measured to be higher than 70 dB, while the laser linewidth remains unchanged. The relative intensity noise of the laser at the relaxation oscillation frequency of 173 kHz is determined to be −115 dB/Hz, which approaches to −134 dB/Hz at frequencies over 500 kHz.

Multiwavelength ytterbium-Brillouin random Rayleigh feedback fiber laser

In this letter, we experimentally demonstrate the multiwavelength ytterbium-Brillouin random fiber laser for the first time, in the half-open cavity formed by a fiber loop mirror and randomly distributed Rayleigh mirrors. With a cladding-pumped ytterbium-doped fiber and a long TrueWave fiber, the narrow linewidth Brillouin pump can generate multiple Brillouin Stokes lines with hybrid ytterbium-Brillouin gain. Up to six stable channels with a spacing of about 0.06 nm are obtained. This work extends the operation wavelength of the multiwavelength Brillouin random fiber laser to the 1 µm band, and has potential in various applications.

Wavelength-locked vectorial fiber laser manipulated by Pancharatnam-Berry phase.

We report a wavelength-locked cladding-pumped ytterbium-doped fiber laser that can simultaneously emit radially and azimuthally polarized beams based on Pancharatnam-Berry phase optical elements. Multi-wavelength free running operation of the radially and azimuthally polarized laser beams can be switched to a single-wavelength one assisted by volume Bragg grating, with wavelength locked at around 1053.4 nm and spectral linewidth of 0.06 nm (FWHW). By rotating the glan-taylor polarizer, we can obtain switchable radially and azimuthally polarized beams output. The radially and azimuthally polarized beams mode purity can maintain 97.3% and 96.3% at maximum output power, and the polarization extinction ratio (PER) can reach 97.8% and 95.9% for the radially and azimuthally polarized laser, respectively.

Cladding-pumped ytterbium-doped fiber laser with radially polarized output.

A simple technique for directly generating a radially polarized output beam from a cladding-pumped ytterbium-doped fiber laser is reported. Our approach is based on the use of a nanograting spatially variant waveplate as an intracavity polarization-controlling element. The laser yielded ~32 W of output power (limited by available pump power) with a radially polarized TM (01)-mode output beam at 1040 nm with a corresponding slope efficiency of 66% and a polarization purity of 95%. The beam-propagation factor (M(2)) was measured to be ~1.9-2.1.

Multi-kilowatt Single-mode Ytterbium-doped Large-core Fiber Laser

We have demonstrated a highly efficient cladding-pumped ytterbium-doped fiber laser, generating <TEX>$&gt;$</TEX>2.1 kW of continuous-wave output power at 1.1 μm with 74% slope efficiency with respect to launched pump power. The beam quality factor (<TEX>$M^2$</TEX>) was better than 1.2. The maximum output power was only limited by available pump power, showing no evidence of roll-over even at the highest output power. We present data on how the beam quality depends on the fiber parameter, based on our current and past fiber laser developments. We also discuss the ultimate power-capability of our fiber in terms of thermal management, Raman nonlinear scattering, and material damage, and estimate it to 10 kW.

Experimental demonstration of enhancing pump absorption rate in cladding-pumped ytterbium-doped fiber lasers using pump-coupling long-period fiber gratings

A long-period fiber grating (LPFG) was inscribed in a single-mode fiber and was spliced with a ytterbium (Yb)-doped double-clad fiber in order to couple pump radiation of the inner cladding into the core in a cladding-pumped fiber laser. The use of an LPFG permits a partial core-pumping scheme in a cladding-pumping fiber laser because a portion of the pump radiation can be coupled to the core by LPFG. The enhancement of the pump absorption of a Yb-doped cladding-pumped fiber laser as the result of pump coupling by LPFG was 35%, and the maximal output power increased by up to 55% when a 20-W pump source is used.

Efficient single-mode operation of a cladding-pumped ytterbium-doped helical-core fiber laser

A novel approach to achieving robust single-spatial-mode operation of cladding-pumped fiber lasers with multimode cores is reported. The approach is based on the use of a fiber geometry in which the core has a helical trajectory within the inner cladding to suppress laser oscillation on higher-order modes. In a preliminary proof-of-principle study, efficient single-mode operation of a cladding-pumped ytterbium-doped helical-core fiber laser with a 30 microm diameter core and a numerical aperture of 0.087 has been demonstrated. The laser yielded 60.4 W of output at 1043 nm in a beam with M2 < 1.4 for 92.6 W launched pump power from a diode stack at 976 nm. The slope efficiency at pump powers well above threshold was approximately 84%, which compares favorably with the slope efficiencies achievable with conventional straight-core Yb-doped double-clad fiber lasers.

Cladding-pumped ytterbium-doped large-core fiber laser with 610 W of output power

We report a cladding-pumped ytterbium-doped fiber laser, generating up to 610 W of continuous-wave (cw) output power at 1.09 μm with a slope efficiency of 82% and with a good beam quality ( M 2=2.7). The core diameter was 43 μm and the inner cladding diameter was 650 μm. Even at this high power, the maximum output power was still limited by the available pump power, and no undesirable roll-over was observed in output power with increasing pump power.

Ytterbium-doped large-core fiber laser with 1.36 kW continuous-wave output power

We have demonstrated a highly-efficient cladding-pumped ytterbium-doped fiber laser generating 1.36 kW of continuous-wave output power at 1.1 mum with 83% slope efficiency and near diffraction-limited beam quality. The laser was end-pumped through both fiber ends and showed no evidence of roll-over even at the highest output power, which was limited only by available pump power.

Characteristics of Q-switched cladding-pumped ytterbium-doped fiber lasers with different high-energy fiber designs

We theoretically and experimentally analyze Q-switched cladding pumped ytterbium-doped fiber lasers designed for high pulse energies. We compare the extractable energy from two high-energy fiber designs: (1) single- or few-moded low-NA large mode area (LMA) fibers and (2) large-core multimode fibers, which may incorporate a fiber taper for brightness enhancement. Our results show that the pulse energy is proportional to the effective core area and, therefore, LMA fibers and multimode fibers of comparable core size give comparable results. However, the energy storage in multimode fibers is mostly limited by strong losses due to amplified spontaneous emission (ASE) or even spurious lasing between pulses. The ASE power increases with the number of modes in a fiber. Furthermore, spurious feedback is more difficult to suppress with a higher NA, and Rayleigh back-scattering increases with higher NA, too. These effects are smaller in low-NA LMA fibers, allowing for somewhat higher energy storage. For the LMA fibers, we found that facet damage was a more severe restriction than ASE losses or spurious lasing. With a modified laser cavity, we could avoid facet damage in the LMA fiber, and reached output pulse energies as high as 2.3 mJ, limited by ASE. Theoretical estimates suggest that output pulse energies around 10 mJ are feasible with a larger core fiber, while maintaining a good beam quality.