Circular Coil Research Articles

Structure optimization of transmission coil of wireless power transmission system for rail transit vehicles

Abstract To solve the transmission efficiency problem of traditional wireless energy systems applied to rail transit vehicles. In this paper, the key components of a wireless power transmission system, such as the transmission efficiency of the transmission coil and the poor anti-deviation ability of the coil, are studied. Firstly, this paper analyzes the traditional planar circular and square coil shapes, analyzes the magnetic field characteristics of the traditional transmission coil structures by ANSYS Maxwell simulation software, and obtains the advantages and disadvantages of different coil structures. According to the analysis structure, the coil structure is optimized and improved, and the coil structure form of the combined coil is put forward. Through the comparative analysis of finite element simulation software, it is attested that combined coil structure has a significant improvement in transmission efficiency and anti-deviation ability.

An application of multi-magnetic circular planar spiral relay to improve the performance of wireless power transfer system

Introduction. The system of delivering electricity without wires is known as wireless power transfer (WPT). The WPT system has been extensively used in a number of industries, health, telecommunications, and transportation. However, the distance between the transmitter and receiver coils has a significant impact on its efficiency. Lower power can be generated between coils the farther apart they are, and vice versa. The novelty of the proposed work is innovative in that it develops a multi-magnetic circular planar spiral relay to improve the WPT system’s performance and designs circular planar spiral coils to achieve an appropriate inductance value for the 5 kHz matching frequency. The goal of paper is to create a circular planar spiral coil with an appropriate inductance value for the 5 kHz matching frequency. Methods. The transmitter circuit, receiver circuit, and DC voltage source are parts of the WPT system. The inverter circuit uses the inductive coupling technique to transform the DC power source into AC voltage on the transmitter coil. The suggested coil is additionally employed as a multi-magnetic circular planar spiral relay in order to increase the mutual inductance between the receiver and transmitter coils. Results. To monitor the power improvement that results from adding a multi-magnetic relay to the system, the transmitter coil, receiver coil, and multi-magnetic relay are positioned at specific distances from each other. With Vdc = 30 V and dtr = 21 cm, the power received at the receiver coil can therefore be improved by up to 67 %. Practical value. The multi-magnetic circular planar spiral relay applied in the WPT system has been investigated in an experimental study and it can be applied for DC load. References 26, table 1, figure 18.

Performance Investigation of Multi-Turn Pickup for Circular Fractal Flexible Planar Eddy Current Probe

ABSTRACT This paper aims to compare and analyze the performance differences between a single-coil and multi-coil pickup coil layout in a flexible circular fractal planar eddy current probe. Flexible planar eddy current probes offer flexibility and adaptability, making them widely used in the detection of complex structures. The circular fractal flexible planar eddy current probe is a new type of probe that has a lower miss rate in detecting cracks at specific angles compared to traditional circular and rectangular coil eddy current probes. However, the single-coil structure of the probe’s pickup coil has the drawback of being less sensitive to weak signals. This paper investigates the detection performance of the flexible circular fractal probe by varying the number of turns in the original pickup coil. Experimental comparisons were conducted by preparing and installing single-coil and multi-coil circular fractal planar eddy current probes. The performance differences between single-coil and multi-coil configurations were compared and analyzed under various excitation frequencies, liftoff distances, and internal crack depths. The results showed that, compared to the single-coil probe, the multi-coil probe exhibited significantly improved detection signal values and sensitivity.

A Twin Spiral Coil Phase Transfer Heat Exchanger for Storing Heat Should Be Designed and Tested in The Lab.

Abstract This in-depth study of thermal energy storage (TES) systems examines their function in resolving time, temperature, power, and location problems within the immense energy system design. With its incredible growth, TES creates a shadow over the future, projecting optimism for a better economy and more reliable energy infrastructure. The study is concentrated on a state-of-the-art heat exchanger that has circular double coils with various diameters, with a reliance on charging process amplification. The trial stage is decorated like a well-coordinated ensemble, integrating shell-and-tube design together with intense evaluation of varied tube morphologies, HTF flow designs, and protecting processes. The TES device effortlessly reveals its many components, such as a gas heater, control valves, a pump, a circular container with spiral HTF tubes, and a chorus of music. The PCM heat storage unit’s performance improved in two resonant cases that evaluated the effect of the HTF input temperature and coil charge in great detail. Case 2 and Case 1’s connections exhibit the significant heat absorption and PCM liquification by creating a web of various temperature differences while charging. With its improved temperature performance and straightforward design, Case 2 displays rapid removal and quicker charging periods. In addition, the study examines the HTF input parameters, which cast light on the constant HTF departure temperatures and demonstrate the importance of temperature during the charging opera. While the total energy storage rate rises with increasing temperatures, the expected scores are in accord with the mood fluctuations at the beginning and end of HTF. This review functions as a folder of vital insights, analyzing notes towards constructing PCM charging processes for higher energy storage efficiency - ultimately placing a limelight on the endless possibilities that TES systems predict in the present spectrum of energy uses.

Influence of magnetic field on renewable oil flame characteristics-an experimental and image processing analysis with bibliometric study

This study investigates the influence of a magnetic field on the flame characteristics of waste cooking oil. A circular current-carrying coil was used to generate magnetic fields of varying strengths (131.37 G, 234.19 G, 337.07 G, 394.12 G, and 428.39 G), corresponding to different voltages (0–10 V). Flame behavior was captured with a digital camera, both without a magnetic field and under varying field strengths. Flame height and area were analyzed using ImageJ and MATLAB's Image Processing tools. Additionally, the thermal properties and fatty acid composition of the waste cooking oil were examined. Results indicated that the flame height increased by 11.06 % under the strongest magnetic field compared to the baseline. The flame area initially expanded due to magnetically induced diffusion but later decreased as the flame stabilized and turbulence reduced. A strong correlation was found between the flame area estimations from ImageJ and MATLAB.

A phase II trial examining the safety and preliminary efficacy of repetitive transcranial magnetic stimulation (rTMS) for people living with multiple sclerosis

BackgroundMultiple sclerosis (MS) is a chronic neurological condition and the leading cause of non-traumatic disability in young adults. MS pathogenesis leads to the death of oligodendrocytes, demyelination, and progressive central nervous system neurodegeneration. Endogenous remyelination occurs in people with MS (PwMS) but is insufficient to repair the damage. Our preclinical studies in mice indicate that endogenous remyelination can be supported by the delivery of repetitive transcranial magnetic stimulation (rTMS). Our phase I trial concluded that 20 sessions of rTMS, delivered over 5 weeks, are safe and feasible for PwMS. This phase II trial aims to investigate the safety and preliminary efficacy of rTMS for PwMS.MethodsParticipants must be aged 18–65 years, diagnosed with MS by a neurologist, stable and relapse free for 6 months, have an Extended Disability Status Scale (EDSS) between 1.5 and 6 (inclusive), willing to travel to a study site every weekday for 4 consecutive weeks, and able to provide informed consent and access the internet. Participants from multiple centres will be randomised 2:1 (rTMS to sham) stratified by sex.The intervention will be delivered with a Magstim Rapid2 stimulator device and circular 90-mm coil or MagVenture MagPro stimulator device with C100 circular coil, positioned to stimulate a broad area including frontal and parietal cortices. For the rTMS group, pulse intensity will be set at 18% (MagVenture) or 25% (Magstim) of maximum stimulator output (MSO), and rTMS applied as intermittent theta burst stimulation (iTBS) (~ 3 min per side; 600 pulses). For the sham group, the procedure will be the same, but the intensity is set at 0%. Each participant will attend 20 intervention sessions over a maximum of 5 weeks.Outcome measures include MS Functional Composite Score (primary), Fatigue Severity Scale, Hospital Anxiety and Depression Scale, Quality of Life, and Pittsburgh Sleep Quality Index/Numeric Rating Scale and adverse events (secondary) and advanced MRI metrics (tertiary). Outcomes will be measured at baseline and after completing the intervention.DiscussionThis study will determine if rTMS can improve functional outcomes or other MS symptoms and determine whether rTMS has the potential to promote remyelination in PwMS.Trial registrationRegistered with Australian New Zealand Clinical Trials Registry, 20 January 2022; ACTRN12622000064707.

Completely Analytical Model of Inductance for Circular Coils With Bilateral Finite Magnetic Cores and Al Plates in WPT Systems

Completely Analytical Model of Inductance for Circular Coils With Bilateral Finite Magnetic Cores and Al Plates in WPT Systems

Optimal design of thick-walled circular coils for uniform magnetic field generation

Abstract Uniform magnetic field coils are widely used as electromagnetic equipment in industrial, medical, and research applications, with Helmholtz coils being a common configuration. For applications requiring a relatively high magnetic field (∼mT), Helmholtz coils typically feature a large coil cross-section. However, this characteristic makes them unsuitable for describing the magnetic field generated by a current loop model during the design process. In this work, we model the magnetic field of a large cross-section Helmholtz coil system, often referred to as a thick-walled Helmholtz coil. By employing a genetic algorithm, we transform the design problem of a Helmholtz coil into a constrained optimization problem. Subsequently, we propose a method for reverse designing a Helmholtz coil based on constraints on the target magnetic field. Finite element simulations verify the accuracy of the established magnetic field calculation model in describing the magnetic field generated by the thick-walled Helmholtz coil. Moreover, the designed Helmholtz coil effectively meets the design constraints and objectives. This method addresses the issue of significant errors in calculating the magnetic field and its uniformity resulting from the cross-sectional effect during the design of thick-walled Helmholtz coils. Furthermore, it satisfies the constraints for coil operating time and lightweight design.

2D axisymmetric electromagnetic modeling of HTS coils based on T-A formulation with modified Newman boundary conditions

The T-A formulation based on thin film approximation has been widely used in electromagnetic modeling of high temperature superconducting (HTS) coated conductors (CCs). However, with the emergence of no-insulation (NI) HTS coils and its variant HTS coils, the electrical connection of HTS coils has become increasingly complex, and the traditional T-A formulation is challenging to handle the problems of conductors with non-negligible thickness and current sharing. This paper firstly describes the Neumann boundary condition of the T-A formulation under 2D axisymmetric symmetry in detail, as well as the conversion of different boundary conditions. And additional voltage variable is added to correct the Newman boundary condition from the perspective of circuit. Then, considering HTS CCs series or parallel stacking to carry current, the effectiveness of this method is verified by comparing with benchmark model. Finally, we extend the application range of the T-A formulation with modified Newman boundary conditions to simulate thick superconductors, and naturally process current sharing of azimuthal and radial current in circular NI HTS coils.

Homogeneous B0 coil design method for open-access ultra-low field magnetic resonance imaging: A simulation study

A multimodal brain function measurement system integrating functional magnetic resonance imaging (fMRI) and magnetoencephalography (MEG) is expected to be a tool that will provide new insights into neuroscience. To integrate fMRI and MEG, an ultra-low-field MRI (ULF-MRI) scanner that can generate a static magnetic field (B0) with an electromagnetic coil and turn off the B0 during MEG measurements is desirable. While electromagnetic B0 coil has the above advantages, it also has a trade-off between size and the broadness of the magnetic field homogeneity. In this study, we proposed a method for designing a B0 multi-stage circular coil arrangement that determines the number of coils required to maximize magnetic field homogeneity and minimize the total wiring length of the coils. The optimized multi-stage coil arrangement had an external shape of 600 mm in diameter and a maximum height of 600 mm, with an aperture of 600 mm in diameter and 300 mm in height. The magnetic field homogeneity was <100 ppm over a 210 mm diameter spherical volume (DSV). Compared to a previous two coil pairs arrangement with the same magnetic field homogeneity, the diameter was 1/1.9 times smaller, indicating that the newly designed B0 coil arrangement realized a smaller size and wider magnetic field homogeneity.

Rotating wireless power transfer: A new concept for wireless charging systems

Fast and safe charging are current concerns in relation to wireless charging of autonomous guided vehicles (AGVs). Wireless Power Transfer (WPT) is a capable solution and a replacement for conventional contact-based methods. However, resonant inductive and capacitive WPT topologies demand more power as the gap between transmitter and receiver pads increases. These structures, initially developed for electric vehicle applications, do not adequately optimize power transfer and power quality for the smaller surface areas of AGVs. In this paper, a novel topology for wireless charging concept is described and validated. This methodology has been named rotating WPT, with a primary side spinning neodymium magnet disc. The receiver pad is composed of a circular coil with ferrite U-cores. Calculations of the induced voltage over the rotating magnetic field resulted in 1.95 V at an operating frequency of 2.7 kHz. FEM simulation results show approximately 3 V, while laboratory experiments outputted 33 mV at 3.8 kHz. A sinusoidal waveform was observed from prototype, and power was successfully transferred to the receiver end, validating this proposed topology. This novel WPT system has no inverter, rectifier, nor compensation, decreasing reactive power, assembly costs and complexity while transferring power and enhancing power quality.© 2017 Elsevier Inc. All rights reserved.

Completely Analytical Calculation of Inductance for Circular Coils With Bilateral Finite Magnetic Cores at Arbitrary Position in WPT Systems

Completely Analytical Calculation of Inductance for Circular Coils With Bilateral Finite Magnetic Cores at Arbitrary Position in WPT Systems

Coupling coefficient calculation method of circular coil with bilateral finite magnetic shields at horizontal misalignment in wireless power transfer systems

AbstractThe coupling coefficient determines the transfer efficiency of the wireless power transfer (WPT) system. The magnetic leakage can be reduced, and the coupling coefficient of the coil can be enhanced by adding a magnetic shield. Thus, the transfer efficiency of the WPT system can be improved. However, when the receiving coil is added with magnetic shield and occurs horizontally misaligned, the coupling coefficients between the coils with the magnetic shield can only be calculated by finite element simulation, and there is no calculation method for the coupling coefficient of two circular coils with bilateral finite magnetic shield at horizontal misalignment. Therefore, based on Maxwell's equations and Bessel's function, the formula of the coupling coefficient between circular coils at coaxial is derived by the subdomain hierarchical analysis (SHA) method. On this basis, the coupling coefficient calculation formula between circular coils at horizontal misalignment is further derived by using the boundary vector equivalence (BVE) method. The results show that the maximum experimental error is not more than 5.58%, and the longest average time of the algorithm is not more than 1.282 s, which verifies the effectiveness and rapidity of the proposed method.

Customized modulation on plasma uniformity by non-uniform magnetic field in capacitively coupled plasma

A two-dimensional fluid model based on COMSOL Multiphysics is developed to investigate the modulation of static magnetic field on plasma homogeneity in a capacitively coupled plasma (CCP) chamber. To generate a static magnetic field, direct current is applied to a circular coil located at the top of the chamber. By adjusting the magnetic field’s configuration, which is done by altering the coil current and position, both the plasma uniformity and density can be significantly modulated. In the absence of the magnetic field, the plasma density exhibits an inhomogeneous distribution characterized by higher values at the plasma edge and lower values at the center. The introduction of a magnetic field generated by coils results in a significant increase in electron density near the coils. Furthermore, an increase in the sets of coils improves the uniformity of the plasma. By flexibly adjusting the positions of the coils and the applied current, a substantial enhancement in overall uniformity can be achieved. These findings demonstrate the feasibility of using this method for achieving uniform plasma densities in industrial applications.

Impact of Titanium Skull Plate on Transcranial Magnetic Stimulation: Analysis of Induced Electric Fields

Background: Implanted titanium skull plates (TSPs) in cranioplasty are used to replace or reconstruct areas of the skull that have been damaged or removed due to trauma, surgery, or other medical conditions. However, the presence of a TSP in the head may influence the distribution of the electric field induced during transcranial magnetic stimulation (TMS) procedures. The purpose of this study was to determine how the presence of TSP would interfere with TMS-induced cortical electric fields. Methods: The TMS with a figure-of-eight coil was applied to a realistic head model with TSPs. The distribution of the induced electric field in head tissues was calculated by employing the impedance method, and the results were compared with that of a normal head without TSP. Results: Simulation results show that the distribution of the induced electric field has changed greatly for the head model with TSP. The maximum value of the induced electric field in head tissues was present under one of the circular coil wings rather than in the tissues beneath the junction of the two wings of the Fo8 coil. Conclusions: The induced electric field in deep brain regions was increased for the head model with TSP, which could potentially lead to deep brain stimulation. Since the presence of metallic TSP can greatly influence the distribution of the induced electric field in TMS applications, it is important to adjust the treatment scheme when considering TMS for individuals with cranial titanium plates.

Measurement of Knee Extensor Torque During Repetitive Peripheral Magnetic Stimulation: Comparison of the Forces Induced by Different Stimulators.

To investigate the factors that induce strong contractions during repetitive peripheral magnetic stimulation (rPMS) and compare the muscle torque induced by two stimulators (Stim A and Stim B) with different coil properties. rPMS was applied to the right vastus lateralis of 30 healthy young adults. Stim A contained a 10.1 cm2 rectangular iron core coil, while Stim B contained a 191 cm2 round coil. The knee extensor torque (KET) induced by rPMS at 30 Hz was measured isometrically and divided by the maximum voluntary contraction (MVC) to obtain a relative value of MVC (%MVC). KET at 100% intensity of Stim A (A100%, 1.08 T) was compared to those at 100% or 70% intensity of Stim B (B100%, 1.47 T vs. B70%, 1.07 T). Additionally, we conducted a comprehensive literature search for studies that measured the KET during rPMS. Both the mean values of %MVC using B100% and B70% were significantly greater than that using A100%. Furthermore, the KET induced by Stim B was found to be larger than that described in previous reports, unless booster units were used to directly stimulate the main trunk of the femoral nerve. Stim B induced a stronger muscle contraction force than Stim A did. This may be because the larger the coil area, the wider the area that can be stimulated. Additionally, a circular coil allows for deeper stimulation.

A Non-inductive Coil Design Used to Provide High-Frequency and Large Currents.

Currently, cutting-edge, high-frequency current sources are limited by switching devices and wire materials, and the output current cannot take into account the demands of a high peak and low rise time at the same time. Based on the output demand of a current source, a non-inductive coil for providing high-frequency, high current sources with low rise times is designed. The coil is appropriately designed according to the principle of the ampere-turn method, where several turns of wire are utilized to linearly synthesize the current to obtain high-frequency currents with amplitudes up to 30 kA. However, the inductance formed after winding the coil could possess a hindering effect on the high-frequency current. In the present investigation, based on the law of energy conservation and utilizing the principle of transformer coupling, the inductor's hindering effect on high-frequency currents is appropriately eliminated by consuming the stored energy of the inductor innovatively. Theoretical calculations and practical tests show that the inductance of a two-layer 28-turn coil is 42 times smaller than that of a two-layer, 28-turn perfect circular spiral PCB coil. The measured inductance is only 6.69 μH, the output current amplitude is calculated to be up to 33 kA with a rise time of 20 ns, and the output waveform corresponding to a 1 MHz square wave is not remarkably distorted. This effective design idea could be very helpful in solving the problem of high peak values and low rise times in high-frequency, high-current source output design.

Enhancing electric vehicle charging performance through series-series topology resonance-coupled wireless power transfer.

The current electric vehicles (EVs) market is experiencing significant expansion, underscoring the need to address challenges associated with the limited driving range of EVs. A primary focus in this context is the improvement of the wireless charging process. To contribute to this research area, this study introduces a circular spiral coil design that incorporates transceiver coils. First, an in-depth analysis is conducted using Ansys Maxwell software to assess the effectiveness of the proposed solution through the magnetic field distribution, inductance properties, and mutual inductance between receiver and transmitter coils. In the next step, a direct shielding technique is applied, integrating a ferrite core bar to reduce power leakage and enhance power transmission efficiency. The ferrite magnetic shielding guides magnetic field lines, resulting in a significant reduction in flux leakage and improved power transmission. Lastly, a magnetic resonance series (SS) compensation wireless system is developed to achieve high coupling efficiency and superior performance. The system's effectiveness is evaluated through co-simulation using Ansys Simplorer software. The results confirm the effectiveness of the proposed solution, showing its ability to transmit 3.6 kilowatts with a success rate approaching 99%. This contribution significantly advances the development of wireless charging systems for electric vehicles, addressing concerns and promoting global adoption.

Evaluation of the Inductive Coupling between Coplanar Concentric Coils in the Presence of the Ground

An analytical approach is presented that allows deriving an exact series-form representation for the flux linkage between two physically large concentric circular coils located on a lossy soil. The expression comes from a three-step analytical procedure. First, the integral expression for the flux linkage is converted into a double integral consisting of a finite and a semi-infinite integral. Next, the semi-infinite integral is recognized to be a well-known tabulated Sommerfeld integral, which may be analytically evaluated straightforwardly. Finally, applying Lommel’s expansion allows rewriting the remaining finite integral as a sum of elementary integrals amenable to analytical evaluation. As a result, the flux linkage between the two coils is given as a sum of spherical Hankel functions of the wavenumber in the air and in the ground, multiplied by a coefficient depending on the geometrical dimensions of the coils. The accuracy and robustness of the proposed formulation is tested by comparing its outcomes with those generated by numerical integration of the complete integral representation for the flux linkage and with the results provided by previous analytical approaches to the same problem. It is found that the use of the derived expression for the inductance makes it possible to obtain significant time savings as compared to numerical quadrature schemes.

Design and characterisation of a cell exposure system with high magnetic field homogeneity: RILZ coils.

In vitro studies requiring controlled exposure to low-frequency electromagnetic fields employ exposure systems with different geometries and configurations, the Helmholtz configuration being one of the most widely used. This configuration has limitations in the homogeneity of the spatial distribution of the magnetic field intensity values. We present the design, manufacturing, and characterisation of a new coil system, called RILZ configuration, which improves the distribution of magnetic field intensity values in the three dimensions of space for three different heights in comparison with the traditional circular coils in Helmholtz configuration. In addition, a comparative study of the cellular response in CT2A cultures exposed to a magnetic field of 50 Hz and 100µT for 48hrs is performed with both exposure systems. The results of the study show reduced values of deviation from the central value of magnetic field intensity using the RILZ coil system. These differences are statistically significant compared to the Helmholtz configuration for the three Cartesian directions: x (p < 0.01), y (p < 0.01), z (p < 0.01). In addition, the intensity values for three different heights are statistically significantly correlated using the RILZ coil system (p < 0.01). The differences in cell behaviour are also statistically significant between the two systems (p < 0.01) and may be directly related to the differences found in the distribution of intensity values between the two systems. This study highlights the importance of the homogeneity of the magnetic field intensity generated by the exposure systems used and offers an effective solution to control the magnetic field exposure parameters in vitro assays.