Development Of Chromatographic Method Research Articles

Application of a Validated HPLC Method for the Determination of Resveratrol, Ferulic Acid, Quercetin, Retinol, and α-Tocopherol in a Cold Cream—Permeability Study

Due to the rapid increase in the use of anti-aging cosmetic products, there is a need to develop valid analytical methods to control their quality. The present work deals with the development and validation of a new chromatographic method for the quantitative determination of five lipophilic components (resveratrol, ferulic acid, quercetin, retinol, and α-tocopherol), with anti-aging properties, in a cold cream (w/o). For the HPLC-UV separation of the active ingredients, an HS, Discovery® Supelco (Supelco Inc., Bellefonte, PA, USA), C18 column (25 cm × 4.6 mm), 5 μm (at 40 °C) was used as a stationary phase while a binary system of A: Acetonitrile with formic acid 0.2% and B: H2O with formic acid 0.2%, in gradient elution (flow 1.5 mL·min−1), was used as mobile. The analytical method was validated according to ICH guidelines Q2(R2), where linearity (r2 ≥ 0.998), selectivity, precision (% recovery 97.1–101.9), and accuracy (%RSD < 2) were evaluated. The processing of the samples for the recovery of the five analytes from the cream was investigated by experimental design methodology and the cross D-optimal technique (% recovery 98.5–102.9, %RSD < 2%, n = 5). Finally, the same analysis was applied to study the transdermal penetration of the active ingredients incorporated in cold cream (over a period of 8 h). Their behavior was compared with the corresponding one in suspension using Franz cells in a vertical arrangement. The new method is considered reliable for the analysis of the anti-aging product.

Green RP-HPLC method for simultaneous quantification of epigallocatechin-3-gallate and rosmarinic acid in lipid-based nanocarriers and biological fluids: Quality by Design-driven optimization and lean six sigma approach

This study presents the development and validation of a reverse-phase high-performance liquid chromatography (RP-HPLC) method for concurrent quantification of EGCG and RA in prepared lipid-based nanocarriers and biological fluids using a QbD approach, greenness assessment, and Six-Sigma methodology. Initially, variations in critical analytical attributes were identified using the Ishikawa fishbone diagram and Risk Priority Number scores. A Taguchi Orthogonal Array design was employed to screen the critical method parameters influencing method development. Systematic optimization of the RP-HPLC method was subsequently achieved using a Box-Behnken design, with the % organic phase, flow rate, and column temperature as the variables. The responses were retention time, tailing factor, and theoretical plates for both EGCG and RA. Chromatographic separation was accomplished with a methanol and 0.1% formic acid (60:40) isocratic flow system on a Phenomenex Luna C18 column (4.6 × 250 mm, 5 μm) at a 1 mL/min flow rate. The method was rigorously validated according to ICH guidelines. Linearity was observed over a concentration range of 2 to 10 µg/mL for both EGCG and RA, yielding correlation coefficients of 0.998 and 0.999, respectively. The LOD and LOQ were determined to be 0.51 µg/mL and 1.54 µg/mL for EGCG, and 0.35 µg/mL and 1.07 µg/mL for RA. Moreover, the %RSD for all validation parameters were consistently below 2%. Forced degradation studies were conducted under acidic, basic, oxidative, and photolytic conditions to elucidate potential degradation pathways and identify degradation products. The developed method was applied to estimate EGCG and RA in prepared lipid-based nanocarriers and biological fluids like blood plasma and urine. Recovery assays in lipid-based nanocarriers, plasma, and urine samples demonstrated excellent recoveries (96.2–102.1%). The method's greenness was assessed using various tools, and its accuracy was evaluated using Six Sigma methodology. Overall, the developed HPLC method offers a rapid, sensitive, and reliable approach for quantifying EGCG and RA, laying the groundwork for their further investigation as anticancer agents, alone and in combination therapies.

Quantitative instrumental thin-layer chromatography method development of astragalin and its chemical diversity in different populations of Nyctanthes arbor-tristis L.

Quantitative instrumental thin-layer chromatography method development of astragalin and its chemical diversity in different populations of Nyctanthes arbor-tristis L.

Development and validation of a gas chromatography method for quantifying metham sodium in diverse plant origin foods

To ensure food safety and public health, it is essential to establish dependable methods for the qualitative and quantitative analysis of pesticide residues in plant origin foods. This study developed and optimized a gas chromatographic method using the QuEChERS approach for detecting metham sodium residues in 22 plant origin foods. The method was refined by adjusting inlet temperature and transformation conditions to effectively convert metham sodium into its primary metabolite, methyl isothiocyanate. Furthermore, parameters such as the extraction solvent type, volume, and purifying agent were systematically optimized. The method achieved a limit of quantification (LOQ) of 0.05 mg/kg, with a linear range from 0.025 to 1.0 mg/L and determination coefficients (R²) from 0.9892 to 0.9999. Recovery rates ranged from 82 % to 102 %, with relative standard deviations (RSDs) between 0.3 % and 6.8 %. Inter-laboratory validation, in accordance with EU SANTE guidelines, confirmed the method's accuracy and reliability. Validation results passed Cochrane's and Grubbs' tests, with repeatability RSDs between 0.70 % and 5.28 % and reproducibility RSDs from 3.62 % to 21.89 %. This method provides a reliable and effective approach for determining metham sodium residues, and addresses a critical gap in current analytical techniques, offering significant contributions to residue monitoring and food safety regulations.

DEVELOPMENT AND OPTIMIZATION OF HPLC METHODS FOR THE CHIRAL SEPARATION OF ARYLPYRAZOLE, CHLOROACETANILIDE AND ORGANOCHLORINE PESTICIDES: CASE STUDIES OF BENZOBICYCLON, ACETOCHLOR AND CHLORDANE.

This work is centered on the development and optimization of High-Performance Liquid Chromatographic methods for the separation of chiral pesticides, particularly benzobicyclon, chlordane and acetochlor employing Agilent Technologies Infinity II chiral HPLC system equipped with a UV – 2000 detector. The stereoisomers were successively separated using a standard analytical column of dimensions 250 mm X 4.6 mm. The Cis– stereoisomers of chlordane exhibited partial baseline separation while the Trans – enantiomers were fully separated. Benzobicyclon and acetochlor enantiomers attained full baseline separation under optimized conditions. Chlordane and benzobicyclon were analyzed using normal phase chromatography [NP]c with a mobile phase of 90% Normal hexane and 10% Isopropanol, while acetochlor was analyzed by reverse phase chromatography [RP] c using 70% methanol and 30% water. Benzobicyclon was later spiked into soil sample and subsequently extracted using Environmental Protection Agency (EPA) methods and the extracts were further analyzed with a shorter analytical column of dimensions 75 mm X 4.6 mm. The HPLC separation revealed that the longer column provided more efficient separation for the benzobicyclon stereoisomers than the shorter column as reflected by high separation factors (?). The high recovery rate of the stereoisomers of benzobicyclon and the internal standard from the soil extracts confirmed the effectiveness of the method of extraction and the HPLC system employed.

Development of a liquid chromatography method for the analysis of oil extract of artemisia cina

Introduction. The problem of development and implementation of own drugs in Kazakhstan today is acute and urgent. The solution to this problem is possible through the use of own resources – domestic medicinal plant raw materials. A promising medicinal raw material is Artemisia cina – an endemic medicinal plant of the of the Turkestan region of Kazakhstan.Aim. Designing a liquid chromatography methodology to analyze the oil extract obtained from Artemisia cina.Materials and methods. Standard sample (SS) of santonin, Artemisia cina’s oil extract. The substance was identified and quantitatively determined using an Agilent Technologies 1200 liquid chromatograph (USA) equipped with ChemStation software.Results and discussion. The main active substance of the oil extract was analyzed using high-performance liquid chromatography (HPLC) method. Choosing the separation conditions for the column involves determining the best composition of the mobile phase and the rate of elution. There were used a reversed-phase system with sorbent C18 and a mobile phase consisting of acetonitrile and a phosphate buffer with a pH of 6.8. Chromatographic studies of the substance were carried out in a gradient mode at an analytical wavelength of 237 nm. The retention time of the standard sample (SS) of santonin matched the retention time (tR) of santonin isolated from the oil extract of Artemisia cina and amounted to 14.3 minutes.Conclusion. A liquid chromatography method has been established for the identification and quantitative determination of the oil extract, focusing on the main active substance, santonin.

Considerations for method development and method translation in capillary liquid chromatography: A tutorial

HPLC remains one of the most widely used measurement techniques for chemical analysis. Capillary LC, which utilizes narrow diameter columns operated at lower flow rates than analytical-scale LC, continues to gain adoption based on its reduced mobile phase consumption and increased sensitivity when coupled to MS detection. This tutorial offers practical insights into the most critical aspects of translating analytical-scale separations to the capillary scale. The selection of pumping systems, detectors, and the potential for performance loss due to extra-column effects are examined within the context of separations using columns with inner diameters ≤ 0.3 mm. Column choices within this diameter range are also detailed, both in terms of stationary phase support options and general commercial availability. The impact of these various factors on the effective development/translation of LC methods down to flow rates under 10 µL/min is described to provide readers with a basis for implementing these strategies within their own analytical workflows.

Stability-indicating high-performance thin-layer chromatography method development and validation for the simultaneous estimation of azithromycin, fluconazole, and secnidazole in active pharmaceutical ingredient and its tablet dosage form

Stability-indicating high-performance thin-layer chromatography method development and validation for the simultaneous estimation of azithromycin, fluconazole, and secnidazole in active pharmaceutical ingredient and its tablet dosage form

PyICLab: An integrated Python-based toolkit for in-silico simulations of ion chromatography

PyICLab is an open-source Python-based package featuring an object-oriented programming (OOP) interface, providing tools for realistic and customized numerical simulations of ion chromatography (IC). In this paper, we showcase PyICLab's use in simulating diverse separation scenarios, including isocratic carbonate elution, gradient hydroxide elution, high-concentration and large-volume injections. The accuracy of the embedded models was validated by demonstrating strong correlations between predicted and experimental results. Additionally, PyICLab's capability to handle complex IC configurations was demonstrated through a simulation of a column-switching system for seawater analysis. PyICLab offers valuable resources for chromatographic optimization, method development, and educational purposes. It is available on PyPI at pypi.org/project/pyIClab. Interested readers can install PyICLab using the pip command in a Python 3.11 or higher environment.

Quantitation of Copper Tripeptide in Cosmetics via Fabric Phase Sorptive Extraction Combined with Zwitterionic Hydrophilic Interaction Liquid Chromatography and UV/Vis Detection

The increasing demand for effective cosmetics has driven the development of innovative analytical techniques to ensure product quality. This work presents the development and validation of a zwitterionic hydrophilic interaction liquid chromatography method, coupled with ultraviolet detection, for the quantification of copper tripeptide in cosmetics. A novel protocol for sample preparation was developed using fabric phase sorptive extraction to extract the targeted analyte from the complex cosmetic cream matrix, followed by chromatographic separation on a ZIC®-pHILIC analytical column. A thorough investigation of the chromatographic behavior of the copper tripeptide on the HILIC column was performed during method development. The mobile phase consisted of 133 mM ammonium formate (pH 9, adjusted with ammonium hydroxide) and acetonitrile at a 40:60 (v/v) ratio, with a flow rate of 0.2 mL/min. A design of experiments (DOE) approach allowed precise adjustments to various factors influencing the extraction process, leading to the optimization of the fabric phase sorptive extraction protocol for copper tripeptide analysis. The method demonstrated excellent linearity over a concentration range of 0.002 to 0.005% w/w for copper tripeptide, with a correlation coefficient exceeding 0.998. The limits of detection and quantitation were 5.3 × 10−4% w/w and 2.0 × 10−3% w/w, respectively. The selectivity of the method was verified through successful separation of copper tripeptide from other cream components within 10 min, establishing its suitability for high-throughput quality control of cosmetic formulations.

Isolation, Development and Validation of Chromatographic Methods for the Estimation of Linoleic Acid from Different Parts of Euphorbia Neriifolia Linn.

Objectives: This is the first report on the development and validation of thin-layer chromatography (TLC) and high-performance thin-layer chromatography (HPTLC)-densitometric methods for the identification of linoleic acid (LA) in petroleum ether extract (PEE) of Euphorbia neriifolia (EN) stem (ST), latex (LX), and bark (BA). Methodology: Chromatographic analyses were performed on silica gel-G and silica gel 60 F254 plates and the antioxidant activities of isolated compounds were investigated by 2,2-diphenyl-1- picrylhydrazyl (DPPH) spectrophotometric assay. Results: The chromatographic analyses revealed better spots and well-separated peaks of LA with retention factor (Rf) values at 0.54 (ST), 0.40 (LX), and 0.64 (BA), respectively. The linearity of the calibration curve ranges from 10-50 ng/spot (ST), 10-100 ng/spot (LX), and 50-200 ng/spot (BA). The proposed method was characterized by better accuracy, better robustness, and good precision, ranging from 0.173 to 0.372% (intra-day) and 0.185 to 0.205% (inter-day). The value of the limit of detection and quantification equal to 1.04 and 3.16 ng/spot in ST, 0.87 and 2.64 ng/spot in LX, and 0.177 and 0.53 ng/spot in BA determined the sensitivity of the method. In the obtained chromatogram, no peak was observed other than the LA which determined the specificity of the method. The % RSD of < 2% after periods of 12, 24, 36, 48, and 72 h determined the stability of standard LA. Conclusion: Thus, the fingerprinting method is valuable in determining the adulterants and in routine quality control of formulations and herbal drugs.

Development, validation and application of a high-performance liquid chromatography method for the detection of ibuprofen in elephant plasma

A simple and accurate method for the determination of ibuprofen concentrations in elephant plasma was developed and validated using reverse phase high-performance liquid chromatography (HPLC). Utilizing a liquid-liquid extraction with ethyl acetate, methanol, and phosphoric acid, samples were separated on an XBridge C18 column. The mobile phase consisted of 0.005 M ammonium phosphate and acetonitrile (40:60, v/v). Both ibuprofen and the internal standard flurbiprofen were quantitated using an ultraviolet (UV) detector set at 214 nm. The lower limit of quantification (LLOQ) was 0.05 μg/mL in 100 μL of plasma. The average recovery was over 95 % while the intra-assay variability ranged from 0.8 to 9.9 % and the inter-assay variability ranged from 2.7 to 9.8 %. The method was used successfully in a therapeutic drug monitoring program for elephants and could be used in future pharmacokinetic studies.

Development and Validation of a High-Performance Thin-Layer Chromatography Method for the Qualitative Analysis and Quantification of Hispidulin in Hydroethanol Extract of S. barbata D. Don

Background: Hispidulin, a flavonoid renowned for its diverse pharmacological activities, is abundant in S. barbata D. Don. Given its prevalence, it is essential to establish a dependable analytical method for quantifying hispidulin in this plant. Methods: This study introduces a sensitive and reliable high-performance thin-layer chromatographic (HPTLC) method for both qualitative and quantitative analysis of hispidulin in S. barbata D. Don. Pre-coated TLC aluminum plates were utilized, and after testing various mobile phase combinations, the most effective separation was achieved with Toluene-ethyl acetate-formic acid (5:4:1, v/v/v). The method underwent extensive validation for linearity, specification, instrument precision, precision, limits of LOD and LOQ, accuracy, and robustness. Results: The developed method demonstrated excellent linearity over a specified concentration range, with a determination coefficient (r2) of 0.988. A well-defined spot at Rf 0.7, corresponding to hispidulin, was observed. The concentration of hispidulin in the hydroethanolic extract of S. barbata D. Don was quantified as 13.02 μg/mg of extract. Conclusion: In conclusion, the HPTLC method presented in this study offers a simple, accurate, and robust tool for quantitatively analyzing hispidulin in the hydroethanol extract of S. barbata D. Don. This method is suitable for routine quality control and standardization of herbal formulations containing S. barbata D. Don, thereby contributing to the advancement of research in natural product- based pharmaceuticals.

Green stability-indicating RP-HPTLC technique for determining croconazole hydrochloride

Abstract The objective of the proposed investigation is the development and validation of a green stability-indicating reverse-phase high-performance thin-layer chromatographic method to determine croconazole hydrochloride (CCZ). The developing system used was an 80:20 v/v mixture of acetone and water. The measurement of CCZ was done at 198 nm. With the use of the Analytical Eco-Scale (AES), ChlorTox, and Analytical GREEnness (AGREE) tools, greenness was evaluated. The linearity was demonstrated by the present method in the 25–1,200 ng/band range. The present approach was additionally reliable, accurate, sensitive, precise, and green. An exceptional greenness profile was demonstrated by the AES, total ChlorTox, and AGREE scales, which were determined to be 89, 1.08 g, and 0.82, respectively. The greenness metrics of the present method were much better than the reported high-performance liquid chromatography approach. Under acid and oxidative degradation circumstances, CCZ was shown to be unstable, while under alkaline and thermal-stress settings, it was sufficiently stable. Furthermore, the stability-indicating component determined by analytical method identified CCZ in the presence of its degradation products. Commercial CCZ cream was found to contain 0.98% w/w of CCZ. The investigation’s results suggested that CCZ in commercially available creams might be regularly examined with the help of the recommended green technology.

Liquid Chromatographic Method Development and Validation Using RP-UPLC for Identification and Quantification of Phenazopyridine Hydrochloride Tablets to Reduce the Time and Cost: A Promising Green Technique

Liquid Chromatographic Method Development and Validation Using RP-UPLC for Identification and Quantification of Phenazopyridine Hydrochloride Tablets to Reduce the Time and Cost: A Promising Green Technique

Development and validation of High-Performance Thin Layer Chromatographic methods for simultaneous determination of antibacterial pharmaceutical formulations containing Clindamycin phosphate.

The main objective of this research is to establish and authenticate the High-Performance Thin-Layer Chromatographic techniques for the simultaneous assessment of Clindamycin phosphate in combination with Tretinoin (formulation-1) and Clindamycin phosphate with Adapalene (formulation-2), both of which are antimicrobial combinations. In the developed HPTLC methods, for combination-1, the optimized mobile phase was a mixture of n-Hexane: Ethyl acetate: ACN: Methanol (5:2:2:1 by volume) with observed Rf values of 0.413 and 0.787 for Clindamycin phosphate and Tretinoin, respectively. Similarly, for combination-2, the mobile phase comprised n-Hexane: Diethyl ether: Dichloromethane: Acetic acid (4:4:2:0.1 by volume) with recorded Rf values of 0.407 and 0.559 for Clindamycin phosphate and Adapalene, respectively. The developed methods are successfully validated as per the regulatory guidelines. This approach proves to be significantly time-saving and costeffective, rendering it suitable for routine analyses of the formulations containing selected antibacterial active pharmaceutical ingredients and commercial formulations.

Stability-indicating high-performance thin-layer chromatography method development and validation for dapagliflozin propanediol monohydrate, vildagliptin, and metformin hydrochloride in active pharmaceutical ingredient and its tablet dosage form

Stability-indicating high-performance thin-layer chromatography method development and validation for dapagliflozin propanediol monohydrate, vildagliptin, and metformin hydrochloride in active pharmaceutical ingredient and its tablet dosage form

High-Performance Liquid Chromatographic Method Development and Validation for Analysis of Expired and Marketed Doxofylline Tablets.

The objectives of the study were to develop a simple, reliable, sensitive and accurate high-performance liquid chromatography (HPLC) method for doxofylline pure and pharmaceutical dosage forms. HPLC method was developed for the estimation of doxofylline in pure and marketed, recently expired, and 1-year expired tablet formulations. Chromatographic separation of the drug was achieved on a stainless steel column 25 cm × 4.6 mm, packed with octadecylsilane bonded to porous silica (5 µm), Cosmosil® C18, column using a mobile phase of Potassium dihydrogen orthophosphate buffer: Acetonitrile pH 5.1 (60:40 v/v) at a flow rate of 1-mL/min. The drug eluted was monitored at 274 nm and the retention time of doxofylline was found to be 3.575 minutes, respectively. The validation of developed methods was done according to ICH Q2 (R1) guidelines. The calibration curve was linear over the range of 5 to 50 µg/mL. The correlation coefficient was found to be 0.9943 for doxofylline. The average retention time was found to be 3.538 minutes. The results were reproducible, showing the effectiveness of the system. The plate number was found to be 4909, which is also within the limit, i.e. ≥ 2000 prescribed in I.P. The dissolution studies of all three marketed, recently expired and 1-year expired formulations were carried out by using 0.01 M HCl and the results showed almost a similar rate of release profile and all three formulations accomplished the drug release within the limit. The developed and validated HPLC method offers a precise, accurate, and efficient analytical tool for the determination of doxofylline in pharmaceutical formulations.

Development of a superheated water chromatography method for the sustainable determination of preservatives in foods and cosmetics

The present research focused on the use of high temperatures to achieve fast separations in Liquid Chromatography (LC) and minimize the consumption of organic solvents. Particularly, superheated water was employed, by exploiting the decrease in dielectric constant of water when increasing the temperature. To realize this kind of application, the availability of LC columns resistant at high temperature is mandatory. Recently, porous graphitic carbon (PGC) columns have been proposed as stationary phases resistant up to 250 °C. Hardware modifications were also necessary to guarantee the efficient heating of the mobile phase prior of entering the column, as well as its rapid cooling before detection by photodiode array (PDA). Specifically, an LC system was interfaced to a GC oven, which hosted the LC column; to achieve a fast and efficient heating of the eluent coming from the autosampler prior to enter into the column, a pre-heating tube was interposed between the autosampler outlet and the column inlet. Instead, a cooling loop was connected between the column outlet and the PDA cell. A mixture of 1-nitroalkanes was used to evaluate the performance of the system in terms of dead volumes, band broadening and peak shape, as well as chromatographic efficiency and resolution. The use of higher temperatures allowed to perform analyses at higher flow rates in reduced analysis time and was also in terms of peak bandwidth resulting to increased efficiency for the most retained compound. Moreover, van't Hoff plots were obtained at different temperature, confirming that the most retained analyte greatly benefited of the temperature increase.The system was applied to the analysis of parabens in cosmetic and food products. The method combined eco-sustainable sample preparation with high-temperature LC separation on a PGC column and was fully validated in terms of linearity, precision, accuracy and detection and quantification limits. The developed method was critically evaluated by comparing the output of different metric tools implemented in the last decade for the quantitative assessment of the greenness.

Theoretical predictions to facilitate the method development in slalom chromatography for the separation of large DNA molecules

Slalom chromatography (SC) re-emerged in 2024 due to the availability of low adsorption ultra-high pressure liquid chromatography (UHPLC) packed columns/instruments and large modalities being investigated in the context of cell and gene therapies. The physico-chemical principles of SC retention combined with hydrodynamic chromatography (HDC) exclusion have been recently reported. In SC, DNA macromolecules are retarded because: (1) they can be stretched to lengths comparable to the particle diameter, and (2) their elastic relaxation time is long enough to maintain them in non-equilibrium extended conformations under regular UHPLC shear flow conditions. Here, a quantitative HDC-SC retention model is consolidated. A general plate height model accounting for the band broadening of long DNA biopolymers along packed beds is also derived for supporting method development and predicting speed-resolution performance in SC.For illustration, the chromatographic speed-resolution properties in SC are predicted for the separation of specific critical pairs (4.0/4.5, 10/11, and 25/27 kbp) of linear dsDNA polymers. The calculations are performed for two available custom-made particle sizes, dp= 1.7 and 2.5μm, at a constant pressure of 10,000 psi. The predictions are directly validated from experimental data acquired using low adsorption MaxPeakTM 4.6 mm i.d. Columns packed with 1.7μm BEHTM 45 Å (15 cm long column) and 2.5μm BEH 125 Å (30 cm long column) Particles, and by injecting six linear dsDNAs (λ DNA-Hind III Digest). The LC system is very low dispersion ACQUITYTM UPLCTM I-class PLUS System, and the mobile phase is a 100 mM phosphate buffer at pH 8. Maximum resolution is always achieved when the average extended lengths of linear dsDNAs are equal to a critical length, which is proportional to the particle diameter and to the square root of the applied shear rate. Most advantageously, the experimental results reveal that the relaxation times of linear dsDNAs observed under shear flow conditions are two orders of magnitude shorter than those expected in the absence of flow: this enables the detection of the longest linear dsDNAs up to 25 kbp without irremediable loss in column performance. Finally, the retention-efficiency model elaborated in this work can be used to rapidly anticipate and develop methods (selection of particle size, column length, and operating pressure) for any targeted DNA and time-resolution constraints.