Charge Transfer Resistance Research Articles

Fabrication of Fe-Zr, Co-Zr, and Ni-Zr Catalysts to Boost CNTs Synthesis from Plastic Wastes and the Electrocatalytic Oxygen Evolution Reaction.

The efficient conversion of plastic wastes to high-value carbon materials like carbon nanotubes (CNTs) is one important issue about the rational recycling, reduction, and reuse of solid wastes. Herein, Fe-, Co-, and Ni-Zr catalysts were prepared and used for CNTs synthesis from polyethylene (PE) waste via a two-stage reaction system. At the same time, the effects of the PE/catalyst ratio and reaction temperature on CNTs synthesis have been studied. Compared with Co-Zr and Ni-Zr, Fe-Zr exhibited the best activity in CNTs synthesis from PE, and it achieved the highest CNTs yield of 806.3 mg/g (per gram of Fe-Zr) at 800 °C with a PE/catalyst ratio of 4. Furthermore, the obtained Fe-Zr/CNTs composite exhibited a low overpotential of 267 mV for the electrocatalytic oxygen evolution reaction (OER) at 20 mA/cm2 in 1 M KOH electrolyte solution, which was 21 mV lower than commercial RuO2 (288 mV) and 50 mV lower than Fe-Zr (317 mV). It was deduced that the in situ growth of CNTs reduced the charge transfer resistance and improved the electron transport efficiency of the Fe-Zr/CNTs composite, leading to superior activity in the electrocatalytic OER. This work provided detailed information for the preparation of the metal/CNTs composite from plastic wastes, which contributed positively to alleviate the environment and energy crisis.

Monitoring the curing, degradation and moisture ingress into alkyl 2-cyanoacrylate adhesives using electrochemical impedance spectroscopy

AbstractElectrochemical impedance spectroscopy (EIS) was employed in an attempt to gain insight into the mechanisms of ethyl 2-cyanoacrylate (ECA) curing (polymerisation) and bonding on aluminium alloy 2024 metal. EIS can detect ionic movement, adsorption processes, charge transfer and storage occurring at an adhesive/substrate interface and/or in a bulk bond line during curing. Low-frequency capacitance measurements demonstrated sensitivity to surface polymerisation reactions and were modelled using an equivalent circuit model with two time constants in series. At a frequency of 1 kHz, changes in the dielectric polymer could be readily followed with time, confirmed by employing a crown ether to accelerate the polymerisation process. Hydrolytic degradation of poly-ECA bonds at a stainless steel interface was also investigated. An equivalent circuit model containing a number of circuit components comprising pore, charge transfer and diffusional impedances, along with polymer film, double layer and diffusional capacitances (represented by constant phase elements), was developed. Three regions were identified in the frequency domain and ascribed to processes taking place at the polymer/electrolyte and polymer/metal oxide interfaces. In short, EIS can be employed to follow the rate of polymerisation of ethyl-2-cyanoacrylate and also the degradation of the resulting polymer in saline solution.

Elucidating the local structure and electronic properties of a highly active overall alkaline water splitting NixCo1-xO/hollow carbon sphere catalyst

A NixCo1-xO/HCS catalyst with superior water-splitting is presented. High water-splitting reaction kinetics and enhanced durability were observed. The structure-function relationship was investigated with XPS, which demonstrated the presence of dominant Ni2+ and Co2+ species and a functionalized HCS support where nucleation of small metal oxide nanoparticles occurred. The PDF showed broadened Nickel/Cobalt-oxide bonds and expansion of the metal-metal pair distances. The alteration of the Metal-Oxide and Metal-Metal-Oxide bonds favored better HER and OER electrocatalysis, also as supported by DFT. EXAFS showed the existence of the bimetallic oxide catalyst and the stretching of the Ni–O bonds due to the coordination of the Ni–O with the Co. The composite exhibited higher activity and enhanced electrocatalytic mechanism towards water splitting through higher exchange current densities (0.615 and 0.886 mA cm−2) and low charge transfer resistance (14 and 10 Ω) respectively. Chronoamperometry proved the catalyst's stability during prolonged electrolysis.

Three-dimensional pine-tree-like bimetallic sulfide with maximally exposed active sites by secondary structural restructuring for efficient electrocatalytic OER

Developing efficient, low-cost and bifunctional catalysts with predominant durability for the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) is an extraordinary challenge in the preparation of green hydrogen energy by electrochemical water splitting. Three-dimensional (3D) transition metal compounds have become a research hotspot as OER electrocatalysts, which can replace noble metal oxides such as RuO2 and IrO2 to reduce application costs. Herein, we synthesized a novel three-dimensional pine-tree-like bimetallic sulfide arrays on nickel foam (FeCoS/NF) using various optimization strategies such as morphology optimization, in situ growth and introduction of heterogeneous structures. The as-synthesized FeCoS/NF electrocatalyst only requires relatively low overpotential of 156 mV to achieve a current density of 20 mA cm−2 for OER, with a Tafel slope of only 37 mV dec−1. It also has a small charge transfer resistance, an electrochemical surface area and good electrochemical stability in alkaline electrolytes. The excellent performance of FeCoS/NF can be attributed to the synergistic effect and amorphous phase of FeCoS as well as the well-defined pine-tree-like array architecture with a large surface area, abundant active sites, and sufficient gas and electrolyte diffusion channels.

Evaluation of Transducer Elements Based on Different Material Configurations for Aptamer-Based Electrochemical Biosensors

The selection of an appropriate transducer is a key element in biosensor development. Currently, a wide variety of substrates and working electrode materials utilizing different fabrication techniques are used in the field of biosensors. In the frame of this study, the following three specific material configurations with gold-finish layers were investigated regarding their efficacy to be used as electrochemical (EC) biosensors: (I) a silicone-based sensor substrate with a layer configuration of 50 nm SiO/50 nm SiN/100 nm Au/30–50 nm WTi/140 nm SiO/bulk Si); (II) polyethylene naphthalate (PEN) with a gold inkjet-printed layer; and (III) polyethylene terephthalate (PET) with a screen-printed gold layer. Electrodes were characterized using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) to evaluate their performance as electrochemical transducers in an aptamer-based biosensor for the detection of cardiac troponin I using the redox molecule hexacyanoferrade/hexacyaniferrade (K3[Fe (CN)6]/K4[Fe (CN)6]. Baseline signals were obtained from clean electrodes after a specific cleaning procedure and after functionalization with the thiolate cardiac troponin I aptamers “Tro4” and “Tro6”. With the goal of improving the PEN-based and PET-based performance, sintered PEN-based samples and PET-based samples with a carbon or silver layer under the gold were studied. The effect of a high number of immobilized aptamers will be tested in further work using the PEN-based sample. In this study, the charge-transfer resistance (Rct), anodic peak height (Ipa), cathodic peak height (Ipc) and peak separation (∆E) were determined. The PEN-based electrodes demonstrated better biosensor properties such as lower initial Rct values, a greater change in Rct after the immobilization of the Tro4 aptamer on its surface, higher Ipc and Ipa values and lower ∆E, which correlated with a higher number of immobilized aptamers compared with the other two types of samples functionalized using the same procedure.

In-situ growth of novel iron oxide/iron organic framework composites as efficient electroactive materials of battery supercapacitor hybrids

Iron oxide (Fe2O3) with a high theoretical capacitance, wide potential ranges and easy availability has attracted much attentions as the electrode material of battery supercapacitor hybrids (BSH). Metal–organic framework (MOF) is one of the promising potential energy storage materials due to its large surface area and controllable pore structures. In this work, novel iron oxide/iron organic framework composites (Fe2O3/FeMOF) are in-situ grown on the Ni foam as efficient energy storage electrodes of BSH. By tuning the solvothermal durations, the morphology changes from random sizes of sheets, regular grown vertical sheets, to flower-like structures. The d-spacing also increases for the Fe2O3/FeMOF synthesized using longer solvothermal durations. The optimal Fe2O3/FeMOF electrode synthesized using 9 h shows a high areal capacitance of 10.97 F/cm2 along with an areal capacity of 5.49 F/cm2 at the current density of 35 mA/cm2, owing to the most regular growth of sheets, the large d-spacing, and the smallest charge-transfer resistances. A BSH composed of the Fe2O3/FeMOF positive electrode and a graphene negative electrode shows a maximum energy density of 0.76 mWh/cm2 at 22.5 mW/cm2. The excellent long-term cycling stability with the capacitance retention of 85% and Coulombic efficiency of 98% are also achieved after 10,000 charge/discharge cycles.

Oxalate and adipate mediated fabrication of CuO nanocrystallites for their electrochemical and supercapacitance studies

Cupric oxide (CuO) has been comprehensively studied in the field of electrochemistry due to its high Tc-Superconducting property. The present work focus on two different CuO materials i.e. CuO-1 and CuO-2 nanocrystallites which are successfully synthesized from their oxalate and adipate precursors respectively. The calcination temperature for the synthesis of CuO from their precursors is ascertained by TGA analysis of the dicarboxylates. Both the CuO materials are thoroughly characterized by SEM–EDS, XRD, IR and XPS spectroscopic techniques. As a candidate for supercapacitor electrode material, CuO-1/C and CuO-2/C showed a specific capacitance of 4.15 F/g and 22.24 F/g using cyclic voltammetry, 10.4 F/g and 46.6 F/g using GCD curves respectively at a current density of 1 A/g. Also, the CuO-1/C and CuO-2/C showed a specific energy density (Es) 1.59 Wh kg−1 and 0.36 Wh kg−1 at a specific power density (Ps) of 0.02 kW kg−1 and 0.025 kW kg−1 respectively. Moreover, the CuO-2/C exhibits ≈ 96.1% coulombic efficiency following 1000 cycles, whereas, CuO-1/C lags in coulombic efficiency with only 51.8%. As a better candidate, CuO-2/C exhibited excellent rate capability with an outstanding cycling stability of 93.7% retention after 1,000 cycles. The factors contributing to the significant specific capacitance of CuO-2/C along with better stability and reproducibility are its low electrolyte resistance Rs (2.47Ω) and charge transfer resistance Rct (1.01 Ω).

In-situ synthesis of Fe3O4@Fe3C nanoparticles with heterostructures embedded in the N-doped porous carbon for high-performance lithium ion batteries

Metal oxides (Fe3O4) have attracted immense attention as high-capacity anode materials for high-performance electrochemical energy storage systems. However, the large structural change and sluggish reaction kinetics in the lithiation and delithiation reactions critically limit their practical development. Here, we design a novel composite consisting of Fe3O4@Fe3C nanoparticles embedded in N-doped porous carbon (Fe3O4@Fe3C-NPC) for lithium ion batteries. Benefiting from the synergistic effect of heterostructures, the Fe3O4@Fe3C-NPC delivers high reversible capacities (911.9 mAh g−1 at 0.2 A g−1, 319.6 mAh g−1 at 5.0 A g−1). The formed heterointerfaces can build an internal electric field, which help to improve reaction kinetics with fast ion diffusion kinetics and low charge transfer resistance. Furthermore, the Fe3O4@Fe3C-NPC//LiFePO4 full cell also displays great performance. The structural design concept and efficient synthesis method in the work can be extended to construct metal oxide/carbide heterostructures for anode materials.

New information about the cyclable capacity fading process of a pouch cell with Li-rich layered oxide cathodes.

Most studies investigate the cyclable capacity fading mechanism of Li-rich layered oxides (LLOs) from the microscopic structure level, lacking discussions about how the structure degradation influences the performance of the pouch cell precisely and quantitatively. Based on the analysis of the evolution of key parameters during the whole cycling period, a new transition-type fading mechanism is proposed. From the early-to-middle stage of the cycling period, polarization increases, most of which is interface-related, causing about 67% of the whole capacity loss. From the middle-to-late stage of the cycling period, active material losses turn out to be the dominating factor, inducing about 61% of the total capacity loss. Diffusion-related polarization, replacing the interface type, is responsible for most of the increased overpotential. Relative analysis confirms that during the early stage, the increase of the charge transfer resistance, induced by CEI (cathode electrolyte interface) growth and initial surface layered-structure degradation, is the main source of interface polarization. As the cycling evolves to the late stage, severe bulky structure degradation, including lattice-oxygen release, Li/Ni mixture and generation of a new spinel phase, turns out to be the major factor, causing further capacity fading.

Facile construction of porous carbon fibers from coal pitch for Li-S batteries

Coal pitch, an important by-product in the coal coking industry with a high output, is a low-cost and high-carbon yield precursor for the manufacturing of high-value carbon materials. Herein, N/O co-doped carbon fiber (CFCP), fabricated by electrospinning using pre-oxidized coal pitch as the precursor, was employed as the sulfur host for Li-S batteries. The presence of more pyrrolic N and graphic N in CFCP than carbon fiber made from polyacrylonitrile benefits the adsorption of lithium polysulfide and the battery’s life. Sulphur-CFCP cathode (S@CFCP) exhibited excellent specific capacity and cyclability, with a specific capacity of 701.1 mAh/g and a low capacity decay rate of 0.088% per cycle over 200 cycles at 2.0 C, respectively. The high ion diffusion rate, low charge transfer resistance, and effective conversion of lithium polysulfides enable the high electrochemical performance of S@CFCP.

In Situ Growth of Hierarchical Silver Sub‐Nanosheets on Zinc Nanosheets‐Based Hollow Fiber Gas‐Diffusion Electrodes for Electrochemical CO2 Reduction to CO

Electrochemical reduction of CO2 (CO2RR) is an effective strategy to mitigate carbon emission effects and store renewable electricity in value‐added feedstocks, but it still suffers low production rate and current density. A nanostructured catalyst offers opportunities to enhance CO2RR activity by contributing numerous active sites and promoting charge transfer. Herein, a Cu hollow fiber gas diffusion electrode (HFGDE) with silver sub‐nanosheets on a zinc nanosheet structure to produce CO is reported. Compared to the HFGDE only possessed zinc nanosheet structure, the as‐prepared HFGDE with hierarchical sub‐nano AgZn bimetal nanosheets exhibits a twice‐partial current density of CO and a CO production rate at the applied potential −1.3 V (versus reversible hydrogen electrode). The unique Ag sub‐nanosheets interconnected Zn nanosheets provide multiple charge transfer channels, and the synergistic effect between Ag and Zn improves the adsorption binding energy of COOH* intermediate, resulting in a lower charge transfer resistance and fast CO2RR kinetics to produce CO. This research demonstrates the high potential of nanoengineering electrocatalysts for HFGDE to achieve highly efficient CO2 reduction.

Effect of Bi2MoO6 Morphology on Adsorption and Visible-Light-Driven Degradation of 2,4-Dichlorophenoxyacetic Acid

The development of highly efficient and stable visible-light-driven photocatalysts for the removal of herbicide 2,4-dichlorophenoxyacetic acid (2,4-D) from water is still a challenge. In this work, Bi2MoO6 (BMO) materials with different morphology were successfully prepared via a simple hydrothermal method by altering the solvent. The morphology of the BMO material is mainly influenced by the solvent used in the synthesis (H2O, ethanol, and ethylene glycol or their mixtures) and to a lesser extent by subsequent thermal annealing. BMO with aggregated spheres and nanoplate-like structures hydrothermally synthesized in ethylene glycol (EG) and subsequently calcined at 400 °C (BMO-400 (EG)) showed the highest adsorption capacity and photocatalytic activity compared to other synthesized morphologies. Complete degradation of 2,4-D on BMO upon irradiation with a blue light-emitting diode (LED, λmax = 467 nm) was reached within 150 min, resulting in 2,4-dichlorophenol (2,4-DCP) as the main degradation product. Holes (h+) and superoxide radicals (⋅O2−) are assumed to be the reactive species observed for the rapid conversion of 2,4-D to 2,4-DCP. The addition of H2O2 to the reaction mixture not only accelerates the degradation of 2,4-DCP but also significantly reduces the total organic carbon (TOC) content, indicating that hydroxyl radicals are crucial for the rapid mineralization of 2,4-D. Under optimal conditions, the TOC value was reduced by 84.5% within 180 min using BMO-400 (EG) and H2O2. The improved degradation performance of BMO-400 (EG) can be attributed to its particular morphology leading to lower charge transfer resistance, higher electron–hole separation, and larger specific surface area.

Mechanism of high sensitivity proton acids doped polypyrrole molecularly imprinted electrochemical sensor and its application in urea detection

Molecularly imprinted electrochemical sensor is a kind of convenient, fast, and stable analyzer, but the conductivity of electrode materials and their affinity with the analyte affect its performance. A proton acid (PSS, SA, SSA) doping method was proposed to improve the electrochemical performance of the polypyrrole molecularly imprinted polymer (PPy-MIP), which promoted the electropolymerization of pyrrole, reduced the charge transfer resistance, and increased the electrochemical surface area. In terms of both improving conductivity and affinity, the response of the proton acids doped the polypyrrole molecularly imprinted electrochemical sensors (PPy-MIECS) to urea was improved by 25-fold (PSS), 5-fold (SA), and 3-fold (SSA) over that of PPy-MIECS. In addition, the PSS-PPy-MIECS was validated for the practical application with a linear detection range from 0.1 mM to 100 mM, high selectivity (α = 39.73), reusability (RSD% = 4.54 %), reproducibility (RSD% = 0.93 %), and stability (11 days). The advantage of proton acid doping method in PSS-PEDOT-MIECS to urea and PSS-PPy-MIECS to glucose extended its application in the performance enhancement of MIECS design.

Boosting visible-light photoelectrochemical water splitting response of WO3–MoS2 nanocomposites by transition metal doping: Experimental and first-principles studies

The current study employs both theoretical and experimental methods to investigate the effect of Ti and Co doping on the WO3 nanocomposite with MoS2 photoanode's photoelectrochemical (PEC) water-splitting reaction. A simple hydrothermal and sol-gel method was adopted for the preparation of samples. The Ti-doped WO3–MoS2 (1.96 at %) sample showed the maximum optical absorption with a photocurrent density of 1.15 mA/cm2 at 1.6 V vs Ag/AgCl. The improvement in photocurrent density may be ascribed to the upward shifting of the conduction band edge towards the H+/H2 redox potential as well as the presence of a large number of active sites in MoS2. A high value of flat band potential of −0.3 V vs Ag/AgCl was achieved in Ti-doped WO3–MoS2, which was confirmed by Mott-Schottky measurements with the corresponding lowest charge transfer resistance at the semiconducting electrode/electrolyte interface. Furthermore, density functional theory calculations have also indicated that on doping WO3 with Ti and Co, there is a slight upward shift in the conduction band minimum, without any significant change in the valence band maximum, with respect to the Fermi level. This study provides new insight into the impact of transition metal doping and nanocomposite of chalcogenide materials for WO3-based PEC electrodes.

Platinum Cluster Decoration on Hollow Carbon Spheres for High-Efficiency Hydrogen Evolution Reaction.

Currently, platinum (Pt)/carbon support composite materials have tremendous application prospects in the hydrogen evolution reaction (HER). However, one of the primary challenges for boosting their performance is designing a substrate with the desired microstructure. Herein, the intact hollow carbon spheres (HCSs) were prepared via template method. Based on the morphology variation of the as-prepared HCSs-x, we conjectured that the polydopamine (PDA) core was generated first and then slowly grew into a complete overburden (SiO2@PDA). Afterward, Pt atomic clusters were anchored on the outer shells of HCSs-4 to construct composite electrocatalysts (Pty/HCSs-4) by a chemical reduction method. Due to the low charge-transfer resistance, the HCSs have a large electrochemical surface area and provide a continuous electron transport pathway, boosting the atom utilization efficiency during hydrogen production and release. The synthesized Pt2.5/HCSs-4 electrocatalysts exhibit excellent HER activity in acidic media, which can be ascribed to the compositional modulation and delicate structural design. Specifically, when the overpotential is 10 A g-1, the overpotential can achieve 92 mV. This work opens a new route to fabricate Pt-based electrocatalysts and brings a new understanding of the formation mechanism of HCSs.

Multi-metal ferrite as a promising catalyst for oxygen reduction reaction in microbial fuel cell.

Improving catalytic activity of cathode with noble metal-free catalysts can significantly establish microbial fuel cells (MFCs) as a sustainable and economically affordable technology. This investigation aimed to assess the viability of utilizing tri-metal ferrite (Co0.5Cu0.5 Bi0.1Fe1.9O4) as an oxygen reduction reaction (ORR) catalyst to enhance the performance of cathode in MFCs. Trimetallic ferrite was synthesized using a sol-gel auto-combustion process. Electrochemical evaluations were conducted to assess the efficacy of as-synthesized composite as an ORR catalyst, employing electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). This evaluation revealed that the impregnation of bismuth in the Co-Cu-ferrite structure improves the reduction current response and reduces the charge transfer resistance. Further experiments were conducted to test the performance of this catalyst in an MFC. The MFC with tri-metal ferrite catalyst generated a power density of 11.44 W/m3 with 21.4% coulombic efficiency (CE), which was found to be comparable with commercially available 10% Pt/C used as cathode catalyst in MFC (power density of 12.14 W/m3 and CE of 23.1%) and substantially greater than MFC having bare carbon felt cathode without any catalyst (power density of 2.49 W/m3 and CE of 7.39%). This exceptionally inexpensive ORR catalyst has adequate merit to replace commercial costlier platinum-based cathode catalysts for upscaling MFCs.

DNA aptamer-functionalized PDA nanoparticles: from colloidal chemistry to biosensor applications

Polydopamine nanoparticles (PDA NPs) are widely utilized in the field of biomedical science for surface functionalization because of their unique characteristics, such as simple and low-cost preparation methods, good adhesive properties, and ability to incorporate amine and oxygen-rich chemical groups. However, challenges in the application of PDA NPs as surface coatings on electrode surfaces and in conjugation with biomolecules for electrochemical sensors still exist. In this work, we aimed to develop an electrochemical interface based on PDA NPs conjugated with a DNA aptamer for the detection of glycated albumin (GA) and to study DNA aptamers on the surfaces of PDA NPs to understand the aptamer-PDA surface interactions using molecular dynamics (MD) simulation. PDA NPs were synthesized by the oxidation of dopamine in Tris buffer at pH 10.5, conjugated with DNA aptamers specific to GA at different concentrations (0.05, 0.5, and 5 μM), and deposited on screen-printed carbon electrodes (SPCEs). The charge transfer resistance of the PDA NP-coated SPCEs decreased, indicating that the PDA NP composite is a conductive bioorganic material. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) confirmed that the PDA NPs were spherical, and dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy data indicated the successful conjugation of the aptamers on the PDA NPs. The as-prepared electrochemical interface was employed for the detection of GA. The detection limit was 0.17 μg/mL. For MD simulation, anti-GA aptamer through the 5′terminal end in a single-stranded DNA-aptamer structure and NH2 linker showed a stable structure with its axis perpendicular to the PDA surface. These findings provide insights into improved biosensor design and have demonstrated the potential for employing electrochemical PDA NP interfaces in point-of-care applications.

DNA aptamer-functionalized PDA nanoparticles: from colloidal chemistry to biosensor applications

Polydopamine nanoparticles (PDA NPs) are widely utilized in the field of biomedical science for surface functionalization because of their unique characteristics, such as simple and low-cost preparation methods, good adhesive properties, and ability to incorporate amine and oxygen-rich chemical groups. However, challenges in the application of PDA NPs as surface coatings on electrode surfaces and in conjugation with biomolecules for electrochemical sensors still exist. In this work, we aimed to develop an electrochemical interface based on PDA NPs conjugated with a DNA aptamer for the detection of glycated albumin (GA) and to study DNA aptamers on the surfaces of PDA NPs to understand the aptamer-PDA surface interactions using molecular dynamics (MD) simulation. PDA NPs were synthesized by the oxidation of dopamine in Tris buffer at pH 10.5, conjugated with DNA aptamers specific to GA at different concentrations (0.05, 0.5, and 5 μM), and deposited on screen-printed carbon electrodes (SPCEs). The charge transfer resistance of the PDA NP-coated SPCEs decreased, indicating that the PDA NP composite is a conductive bioorganic material. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) confirmed that the PDA NPs were spherical, and dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), and Raman spectroscopy data indicated the successful conjugation of the aptamers on the PDA NPs. The as-prepared electrochemical interface was employed for the detection of GA. The detection limit was 0.17 μg/mL. For MD simulation, anti-GA aptamer through the 5′terminal end in a single-stranded DNA-aptamer structure and NH2 linker showed a stable structure with its axis perpendicular to the PDA surface. These findings provide insights into improved biosensor design and have demonstrated the potential for employing electrochemical PDA NP interfaces in point-of-care applications.

Combinatorial Analysis of Silver‐Palladium Alloy Thin Film Libraries

Combinatorial analysis of Ag–Pd alloy thin films shows the formation of a solid solution with the face‐centered cubic structure for all investigated alloy compositions. Using mixed matter theory and the high field model, oxide growth upon applying an anodic potential is indicated. Electrochemical impedance spectroscopy supports the idea of oxide formation based on a change in behavior correlated to a sharp increase in oxide formation as indicated by cyclic voltammetry measurements. After polarization at 4 V, a stable total impedance and increasingly less‐pronounced phase shift are detected in the frequency range of 100 mHz to 10 kHz, which encompasses the common range of application of active implantable medical devices (AIMD). Upon fitting the measured impedance data with the Randles circuit, capacitances are determined in the nF cm−2 range for the investigated alloys and attributed to the formed mixed oxide layer. Charge transfer resistances are found to be in the kΩ cm−2 range. No correlation between alloy composition and capacitance or resistance can be detected so far. These findings indicate a fundamental applicability of Ag–Pd alloys for use in AIMD.

Synthesis of Poly‐Pyrrole Nanotubes/Chromium Vanadate Composite as Wired Interlocks to Achieve an Asymmetric Supercapacitor Device with Scaled Electrochemical Energy Parameters

AbstractHerein, a novel combination with a focused morphology is designed after synthesizing CrVO4 (CV) nanoparticles and poly‐pyrrole nanotubes (PNT or P) to prepare the interlocks of the composites of PNT and CrVO4 as 1PCV1, 1PCV2, 2PCV1, and 2PCV2 to study the supercapacitor application. Structural and spectral characterizations are perpetuated to confirm the synthesis of the samples. Results furnishing best energy storage are obtained for the intercalated composite 2PCV1 examined for three‐probe and two‐probe set‐up. The excel values for specific capacitance (Cs) for 2PCV1 concerning the Cyclic voltammetry (CV) cycle and Galvanostatic Charge Discharge (GCD) curve are 1745.60 F g−1 at 10 mV s−1 rate and 1545.62 F g−1 at 0.625 A g−1 current density studied along with interface controlled and transport‐controlled Cs with a contribution of 55.13% interface part and 44.87% transport part at 5 mV s−1 scan rate. Electrochemical Impedance Spectroscopy (EIS) study has provided 0.86 n‐factor with solution resistance Rs of 1.48 Ω, and a charge transfer resistance of 0.166 Ω. The respective specific power and specific energy values obtained through the two‐probe set‐up are also interestingly high 416.68 W kg−1 and 45.14 Wh kg−1 at 0.83 A g−1 current density. Also, the retention % in Cs values is studied by running 5000 continuous voltammetric cycles with 96.23% retention in supercapacitor device.