Charged Filters Research Articles

The impact of particle deposition on collection efficiency of electret fibers

This study presents a microscale simulation method that allows one to study the impact of particle loading on the aerosol capture efficiency of an electrostatically charged filter. This was done by considering a bipolarly charged fiber loaded with different amounts of neutral and charged particles with a diameter of 300 nm. The simulations predicted the deposition pattern of the aerosol particles as well as their impact on the electrostatic field of the bipolar fiber. The particle-loaded fiber was then challenged with aerosol particles in the range of 50 nm to 1 μm and with different charge polarities to study how the electrostatic field of the deposited particles interacts with that of the fiber to attract or repel the incoming airborne particles. More specifically, our simulations revealed that particle deposition can enhance the capture efficiency of a bipolar fiber when it is challenged with small particles (smaller than about 400 nm) regardless of the charge polarity of the airborne or deposited particles. The numerical simulations reported in this paper were conducted using the ANSYS CFD code enhanced with in-house subroutines to superimpose the electrostatic field of the deposited particles to that of the bipolar fiber and to include Brownian, polarization, and Coulomb forces in particle trajectory calculations.

Dual-network fiber-hydrogel membrane for osmotic energy harvesting.

Osmotic energy harvesting was a promising way to alleviate energy crisis with reverse electrodialysis (RED) membrane-based technology. Charged hydrogel combined with other materials was an effective strategy to overcome problems, including restricted functional groups and complicated fabrication, but the effect of the respective charges of the two materials combined on the membrane properties has rarely been studied in depth. Herein, a new method was proposed that charged hydrogel was equipped with charged filter paper to form dual network fiber-hydrogel membrane for osmotic energy harvesting, which had excellent ion selectivity (beyond 0.9 under high concentration gradient), high ion transference number and energy conversion efficiency (beyond 32.5% under wide range concentration gradient), good property of osmotic energy conversion (∼4.84W/m2 under 50-fold KCl and ∼6.75W/m2 under simulated sea water and river water). Moreover, the power density was attributed to the surface-space charge synergistic effect from large amounts overlapping of electric double layer (EDL), so that the transmembrane ion transport was enhanced. It might be a valid mode to extensively develop the osmotic energy harvesting.

Empowering powdered activated carbon (PAC) with 3D printing: Achieving highly efficient and reusable cationic dye removal

Powdered activated carbon (PAC) has been extensively used as an effective adsorbent. Despite its excellent adsorption ability, PAC has drawbacks, including difficulty in filtration and reactivation after use, limitations of mass transfer in deeper areas because of its aggregated powder form, and limited applicability in high-flow systems. To overcome these limitations, we used a three-dimensional (3D) printing system to fabricate PAC into a 3D structure. Spectral and microscopic analyses indicated that PAC was embedded into 3D monolith and exhibited high porosity suitable for facile mass transfer. The designed 3D PAC filter effectively removed 200 ppm-methylene blue (MB) within 8 h and showed an adsorption efficiency of 93.4 ± 0.9%. The adsorption of MB onto the 3D PAC filter was described by the pseudo-first-order kinetic and Freundlich isotherm models. The negatively charged 3D PAC filter might attract the positively charged MB, thus favoring the physical adsorption of MB onto the 3D PAC filter. The adsorption performance of the 3D PAC filter was tested at various pH levels of 4–10 and against MB spiked in seawaters and freshwaters to evaluate its feasibility for use in real environments. Finally, the reproducibility and reusability of the 3D PAC filter were demonstrated through repeated adsorption and desorption processes against MB.

Charge Protection in Electret Air Filtration Nonwoven Materials

AbstractNonwoven media used as electret air filters are often embedded with charges to improve particle capture efficiency. These charged filters are invariably exposed to low surface tension fluids such as oils and alcohols leading to charge loss. In this study, filtration media are endowed with charge protection through increased surface repellency using melt additives that can migrate to the surface during processing. Nonwovens containing fluorochemical melt additives are produced, and examined to determine the relationship between surface chemistry, isopropyl alcohol (IPA) repellency, resultant charge retention, and filtration characteristics. Surface fluorine/carbon (F/C) ratios of ≈0.2 are sufficient to protect filtration performance from vapor discharging methods. Samples with bulk additive loadings of 1.2% or higher are found to achieve the necessary repellency to resist discharging independent of the migration state of the sample, while samples loaded at the 0.6% level required sufficient migration to achieve the requisite F/C ratio of 0.2 in order to be protected. Samples that achieved the necessary surface chemistry to provide significant IPA repellency retained > 80% of electret charge and corresponding filtration performance. These results have special significance in the design of filtration media relevant in global healthcare and other industrial settings.

Research on the removal of charged colloidal filter materials from coolants in nuclear power plants

In this paper, nano-grade aluminum powder was used as raw material to prepare glass fiber filter material with positive Zeta potential by hydrothermal method. Since colloids of activated corrosion products in primary circuit of nuclear power plant are mainly electronegative, the filter material prepared in this experiment was used to remove colloidal particles in coolant by combining traditional mechanical filtration with electrostatic adsorption, thus improving the removal efficiency of colloidal particles. The leaching problem of soluble silicon in glass fiber filter material was studied. The leaching amount of soluble silicon in glass fiber filter material was decreased while the filtration efficiency was improved. Consequently reduce the risk of safe operation of nuclear power plants.

Quaternary ammonium salt coated air filter for bioaerosol removal from building indoor air

Developing air filters with biocidal ability is important to protect the public from infectious respiratory diseases. A simple spray-coating approach was devised to fabricate antimicrobial air filters to remove bioaerosols. The commercial antimicrobial agent Goldshield 75 was coated on the air filters through covalent immobilization, endowing the fabricated filter with long-lasting biocidal ability. All coated filters significantly inhibited both Gram-positive bacteria (Micrococcus luteus) and Gram-negative bacteria (Escherichia coli). The antibacterial ability of the coated filters is similar to the commercial AeraSafe antibacterial filter. The coated filter showed over 99.9 % antibacterial efficiency 3 months after the application of the coating. Both bacterial and virus filtration efficiencies of coated charged polypropylene filter were higher than 99.9 %. The coating did not have much effect on the NaCl aerosol filtration efficiency of the filters. This simple spray-coating strategy is a practical method for producing antimicrobial air filters for the prevention of infectious respiratory diseases.

Designing Multi-Layer electret filters via numerical simulation

The deposition of neutral and charged particles inside an electrostatically charged filter can affect its performance by decreasing its ability to capture additional particles and by increasing its pressure drop. The particle-loaded behavior of a composite filter comprised of three fibrous layers is studied in this paper using a macroscale simulation approach. Each of these fibrous layers were assumed to have fibers with the same amount of charge but different charge polarities of only unipolar positive, only unipolar negative, or only bipolar. The charged layers were stacked on top of one another in three different configurations with respect to the flow direction and their filtration efficiency and pressure drop were compared during particle loading with neutralized particles (having the Boltzmann equilibrium charge distribution), singly-charged particles, and neutral particles. Our simulations revealed that placing the bipolarly-charged layer downstream of the unipolarly charged layers helps to lower the negative impact of particle deposition on pressure drop and filtration efficiency of the resulting composite filter. This study introduces a design tool which can be used to optimize the configuration of a composite filter for enhanced particle capture efficiency and reduced pressure drop increase.

Microscale modelling of electret filters using disordered 2-D domains

This paper reports on a computational study about the impact of fiber dipole orientation on particle collection efficiency of a bipolarly charged filter. The simulations were carried out using ANSYS software in a series of 2-D geometries comprised of randomly distributed fibers. The simulations were enhanced with in-house subroutines to incorporate Coulomb and dielectrophoretic forces in calculating particle trajectories and thereby simulating filter efficiency. The highest and lowest efficiencies were observed for dipole orientations that were perpendicular and parallel to the airflow direction, respectively. The simulation results were also compared with the predictions of the popular semi-empirical correlations from the literature and good general agreement was observed, without the need for any empirical correction factors. In addition, it was observed that the predictions of the semi-empirical correlations better agreed with the simulation results obtained for media comprised of fibers with random dipole orientations when challenged with neutralized particles.

Macroscale simulation of particle loading in electrostatically charged filters

Existing studies have shown that particle collection efficiency of a charged filter tends to decrease with particle loading to a certain extent, then increase with further loading. This contrasts with pressure drop which monotonically increases with particle loading. This trend in particle collection efficiency is due to a variety of factors including, but not limited to, neutralization and aerodynamic shielding of the fibers' electrostatic field. The current paper presents a semi-empirical macroscale simulation method to predict the instantaneous pressure drop and particle collection efficiency of an electrostatically charged filter during the early stages of particle loading. The simulations were performed by using ANSYS software enhanced with a series of in-house subroutines. The simulation results are compared with experimental data (for calibration and validation) obtained from testing a bipolarly-charged (55 μC m−2) polypropylene filter exposed to different levels of nanoparticle loadings. The filter media was loaded (both experimentally and computationally) with polydisperse NaCl nanoparticles (count median diameter of 75 nm) having charge values of ±1e. The loaded media were then tested (experimentally and computationally) with NaCl nanoparticles spanning 10 nm–500 nm in electrical mobility diameter (from TSI 3160 filter tester) having a Fuchs charge distribution. In addition, a high-porosity conditional factor was developed for the Kozeny-Carman permeability equation to expand its application to the case of nanoparticle deposits, where the dendrites’ porosity is very high, and aerodynamic slip is expected to occur.

Miniprep assisted proteomics (MAP) for rapid proteomics sample preparation.

Complete enzymatic digestion of proteins for bottom-up proteomics is substantially improved by use of detergents for denaturation and solubilization. Detergents however, are incompatible with many proteases and highly detrimental to LC-MS/MS. Recently; filter-based methods have seen wide use due to their capacity to remove detergents and harmful reagents prior to digestion and mass spectrometric analysis. We hypothesized that non-specific protein binding to negatively charged silica-based filters would be enhanced by addition of lyotropic salts, similar to DNA purification. We sought to exploit these interactions and investigate if low-cost DNA purification spin-filters, 'Minipreps,' efficiently and reproducibly bind proteins for digestion and LC-MS/MS analysis. We propose a new method, Miniprep Assisted Proteomics (MAP), for sample preparation. We demonstrate binding capacity, performance, recovery and identification rates for proteins and whole-cell lysates using MAP. MAP recovered equivalent or greater protein yields from 0.5-50 μg analyses benchmarked against commercial trapping preparations. Nano UHPLC-MS/MS proteome profiling of lysates of Escherichia coli had 99.3% overlap vs. existing approaches and reproducibility of replicate minipreps was 98.8% at the 1% FDR protein level. Label Free Quantitative proteomics was performed and 91.2% of quantified proteins had a %CV <20% (2044/2241). Miniprep Assisted Proteomics can be performed in minutes, shows low variability, high recovery and proteome depth. This suggests a significant role for adventitious binding in developing new proteomics sample preparation techniques. MAP represents an efficient, ultra-low-cost alternative for sample preparation in a commercially obtainable device that costs ∼$0.50 (USD) per miniprep.

Moving environmental DNA (eDNA) technologies from benchtop to the field using passive sampling and PDQeX extraction

AbstractEnvironmental DNA (eDNA) metabarcoding has shown great promise as an effective, non‐invasive monitoring method for marine biomes. However, long filtration times and the need for state‐of‐the‐art laboratories are restricting sample replication and in situ species detections. Methodological innovations, such as passive filtration and self‐contained DNA extraction protocols, have the potential to alleviate these issues. We explored the implementation of passive sampling and a self‐contained DNA extraction protocol by comparing fish diversity obtained from active filtration (1 L; 0.45 μm cellulose nitrate [CN] filters) to five passive substrates, including 0.45 μm CN filters, 5 μm nylon filters, 0.45 μm positively charged nylon filters, artificial sponges, and fishing net. Fish diversity was then compared between the PDQeX Nucleic Acid Extractor and the conventional Qiagen DNeasy Blood &amp; Tissue protocol. Experiments were conducted in both a controlled mesocosm and in situ at the Portobello Marine Laboratory, New Zealand. No significant differences in fish diversity were observed among active filtration and more porous passive materials (artificial sponges and fishing net) for both the mesocosm and harbor waters. For the in situ comparison, all passive filter membranes detected a significantly lower number of fish species, resulting from partial sample drop‐out. While no significant differences in fish eDNA signal diversity were observed between either DNA extraction methods in the mesocosm, the PDQeX system was less effective at detecting fish for the in situ comparison. Our results demonstrate that a passive sampling approach using porous substrates can be effectively implemented to capture eDNA from seawater, eliminating vacuum filtration processing. The large variation in efficiency observed among the five substrate types, however, warrants further optimization of the passive sampling approach for routine eDNA applications. The PDQeX system can extract high‐abundance DNA in a mesocosm with further optimization to detect low‐abundance eDNA from the marine environment.

Nonlocal measurement of quasiparticle charge and energy relaxation in proximitized semiconductor nanowires using quantum dots

The lowest-energy excitations of superconductors do not carry an electric charge, as their wave function is equally electron-like and hole-like. This fundamental property is not easy to study in electrical measurements that rely on the charge to generate an observable signal. The ability of a quantum dot to act as a charge filter enables us to solve this problem and measure the quasiparticle charge in superconducting-semiconducting hybrid nanowire heterostructures. We report measurements on a three-terminal circuit, in which an injection lead excites a non-equilibrium quasiparticle distribution in the hybrid system, and the electron or hole component of the resulting quasiparticles is detected using a quantum dot as a tunable charge and energy filter. The results verify the chargeless nature of the quasiparticles at the gap edge and reveal the complete relaxation of injected charge and energy in a proximitized nanowire, resolving open questions in previous three-terminal experiments.

Analysis of Energy and Exergoeconomic on Water Cleaning and Injection Facilities in the CPP Block, Indonesia

One of the problems in the upstream oil and gas industry is that large quantities of produced water must go through a water cleaning and injection process in accordance with the Regulation of the State Minister of the Environment Number 19 of 2010 of the Republic of Indonesia concerning the quality standards of wastewater for oil and gas and geothermal activities. A total of 224,257.1 barrels of water per day which is produced water in the CPP Block must go through a water management process which requires a large energy consumption of 269.47 MW/month. One effort to reduce the use of electrical energy is to conduct energy and exergy analysis to determine the point of greatest energy use as a result of exergy destruction and convert it into economic costs as operating cost losses. From the research, it is known that the largest electrical energy consumption is at the injection pump 235.47 MW/month with exergy 67.72 KW, the largest exergy destruction is 31.04 KW at the charge filter pump with an efficiency of 54%. Energy and exergy analysis is used to identify changes in energy quality in a system.

Cleavage of High Molecular Weight Kininogen and Bradykinin Release By Red Blood Cell Microvesicles As a Putative Mechanism for Hypotensive Transfusion Reactions

Background: Hypotensive transfusion reactions are adverse events typified by a sudden decrease in blood pressure that usually occurs within the first minutes after the initiation of a transfusion and resolves shortly after the transfusion is stopped. Due to current passive reporting practices, the incidence is likely underreported, but recent studies estimate an incidence of 1.3 cases per 10000 RBC units. The pathophysiology of these reactions are not fully understood. One hypothesis proposed is that increased bradykinin (BK), a nonapeptide released from cleavage of high molecular weight kininogen (HK), as seen with the use of negatively charged leukoreduction filters and the use of angiotensin-converting enzyme inhibitors, is a major contributor to the pathophysiology. We have recently demonstrated that red blood cell derived microvesicles (RBCMVs) from aging red blood cell (RBC) units are able to trigger thrombin generation via kallikrein activation - a predominant enzyme to cleave high molecular weight kininogen (Noubouossie, Blood, 2020). Thus, we hypothesize that the same RBCMVs would lead to bradykinin generation and might explain these hypotensive events.Objectives: To determine if RBC storage lesion-derived microvesicles are able to facilitate HK cleavage and BK release.Methods: RBCMVs were prepared from 4 recently expired RBC units (42 or 43 day old, AS-3 preserved, prestorage leukoreduced, all A+) via a series of centrifugations and washes. RBCMVs were quantified and characterized using nanoparticle tracking analysis. Obtained RBCMVs were first assessed for the capacity to initiate thrombin generation in microvesicle free human plasma via a substrate cleavage assay. Next, RBCMVs were added to a buffer reaction containing prekallikrein and HK, and kininogen cleavage was assessed via western blot. RBCMVs were also mixed with microvesicle-free human plasma and analyzed for evidence of kallikrein activation, cleavage of high molecular weight kininogen, and bradykinin production by ELISA. Cohn fractionation of plasma was used to enrich for BK.Results: RBCMVs were enumerated and concentrated to 7.5 ± 1.4 x 10 12 per mL (mean±SD size 160 ± 29µm). RBCMVs were able to initiate thrombin generation principally via contact pathway activation, independently of tissue factor. In a buffer system RBCMVs demonstrated activity to generate kallikrein with a sequential high molecular weight kininogen cleavage in a dose-dependent manner. Exclusion of kallikrein from the buffer system or addition of the small molecule inhibitor of kallikrein - ecallantide - halted cleavage of kininogen. A dose-dependent cleavage of high molecular weight kininogen indicated that RBCMVs could cause BK release in plasma; this was confirmed via an independent assay of Cohn -fractionated samples.Conclusions: Results of this current study demonstrate that RBCMVs are leading to high HK cleavage via kallikrein activation in vitro. We suspect that the same mechanisms could lead to BK generation in patients receiving older RBC units, possibly increasing the risk for hypotensive events from transfusion. DisclosuresKarafin: Westat, Inc.: Consultancy. Key: Sanofi: Consultancy; BioMarin: Honoraria, Other: Participation as a clinical trial investigator; Takeda: Research Funding; Grifols: Research Funding; Uniqure: Consultancy, Other: Participation as a clinical trial investigator.

Infectious Salmon Anemia Virus Shedding from Infected Atlantic Salmon (Salmo salar L.)—Application of a Droplet Digital PCR Assay for Virus Quantification in Seawater

Infectious salmon anemia virus (ISAV) infection is currently detected by fish sampling for PCR and immunohistochemistry analysis. As an alternative to sampling fish, we evaluated two different membrane filters in combination with four buffers for elution, concentration, and detection of ISAV in seawater, during a bath challenge of Atlantic salmon (Salmo salar L.) post-smolts with high and low concentrations of ISAV. Transmission of ISAV in the bath challenge was confirmed by a high mortality, clinical signs associated with ISA disease, and detection of ISAV RNA in organ tissues and seawater samples. The electronegatively charged filter, combined with lysis buffer, gave significantly higher ISAV RNA detection by droplet digital PCR from seawater (5.6 × 104 ISAV RNA copies/L; p < 0.001). Viral shedding in seawater was first detected at two days post-challenge and peaked on day 11 post-challenge, one day before mortalities started in fish challenged with high dose ISAV, demonstrating that a large viral shedding event occurs before death. These data provide important information for ISAV shedding that is relevant for the development of improved surveillance tools based on water samples, transmission models, and management of ISA.

Nano-engineered tools in the diagnosis, therapeutics, prevention, and mitigation of SARS-CoV-2

The recent outbreak of SARS-CoV-2 has forever altered mankind resulting in the COVID-19 pandemic. This respiratory virus further manifests into vital organ damage, resulting in severe post COVID-19 complications. Nanotechnology has been moonlighting in the scientific community to combat several severe diseases. This review highlights the triune of the nano-toolbox in the areas of diagnostics, therapeutics, prevention, and mitigation of SARS-CoV-2. Nanogold test kits have already been on the frontline of rapid detection. Breath tests, magnetic nanoparticle-based nucleic acid detectors, and the use of Raman Spectroscopy present myriads of possibilities in developing point of care biosensors, which will ensure sensitive, affordable, and accessiblemass surveillance. Most of the therapeutics are trying to focus on blocking the viral entry into the cell and fighting with cytokine storm, using nano-enabled drug delivery platforms. Nanobodies and mRNA nanotechnology with lipid nanoparticles (LNPs) as vaccines against S and N protein have regained importance. All the vaccines coming with promising phase 3 clinical trials have used nano-delivery systems for delivery of vaccine-cargo, which are currently administered widely in many countries. The use of chemically diverse metal, carbon and polymeric nanoparticles, nanocages and nanobubbles demonstrate opportunities to develop anti-viral nanomedicine. In order to prevent and mitigate the viral spread, high-performance charged nanofiber filters, spray coating of nanomaterials on surfaces, novel materials for PPE kits and facemasks have been developed that accomplish over 90% capture of airborne SARS-CoV-2. Nano polymer-based disinfectants are being tested to make smart-transport for human activities. Despite the promises of this toolbox, challenges in terms of reproducibility, specificity, efficacy and emergence of new SARS-CoV-2 variants are yet to overcome.

A review on recent trends of antiviral nanoparticles and airborne filters: special insight on COVID-19 virus.

Novel corona virus (COVID-19) pandemic in the last 4 months stimulates the international scientific community to search for vaccine of antiviral agents suitable for in activating the virus inside and outside the human body. More than 4 million people globally are infected by the virus and about 300,000 dead cases until this moment. The ventilation and airborne filters are also investigated aiming to develop an efficient antiviral filtration technology. Human secretion of the infected person as nasal or saliva droplets goes as airborne and distributes the virus everywhere around the person. N95 and N98 filters are the must use filters for capturing particles of sizes around 300 nm. The average size of the novel corona virus (COVID-19) is 100 nm and there is no standard or special filter suitable for this virus. The nanoparticle-coated airborne filter is a suitable technique in this regard. While the efficiency of this type of filters still needs to be enhanced, new developed nanofiber filters are proposed. Most recently, the charged nanofiber filters of sizes below 100 nm are developed and provide an efficient viral filtration and inactivation. The efficiency of filter must be kept at accepted level without increasing the pressure drop. The present review outlines the most efficient antiviral nanoparticles including the recent functional nanoparticles. The filtration theory, filtration modeling, filter testing, and different types of filter with special concentration on the charged nanofiber filter were discussed. The charged nanofiber filter able to capture novel corona virus (COVID-19) with 94% efficiency and a pressure drop less than 20 MPa.

Short communication: Evaluation of charged membrane filters and buffers for concentration and recovery of infectious salmon anaemia virus in seawater.

Infectious salmon anaemia virus (ISAV) is the cause of an important waterborne disease of farmed Atlantic salmon. Detection of virus in water samples may constitute an alternative method to sacrificing fish for surveillance of fish populations for the presence of ISA-virus. We aimed to evaluate different membrane filters and buffers for concentration and recovery of ISAV in seawater, prior to molecular detection. One litre each of artificial and natural seawater was spiked with ISAV, followed by concentration with different filters and subsequent elution with different buffers. The negatively charged MF hydrophilic membrane filter, combined with NucliSENS® lysis buffer, presented the highest ISAV recovery percentages with 12.5 ± 1.3% by RT-qPCR and 31.7 ± 10.7% by RT-ddPCR. For the positively charged 1 MDS Zeta Plus® Virosorb® membrane filter, combined with NucliSENS® lysis buffer, the ISAV recovery percentages were 3.4 ± 0.1% by RT-qPCR and 10.8 ± 14.2% by RT-ddPCR. The limits of quantification (LOQ) were estimated to be 2.2 x 103 ISAV copies/L of natural seawater for both RT-qPCR and RT-ddPCR. The ISAV concentration method was more efficient in natural seawater.

Anionic Polysaccharide-Modified Filter Papers for Rapid Isolation of Extracellular Vesicles from Diverse Samples in a Simple Bind-Wash-Elute Manner.

Extracellular vesicles (EVs) play a significant role in the pathophysiological process of many diseases, highlighting their values in medical diagnosis and disease monitoring. However, the current EV isolation methods are time-consuming, inconvenient to operate, and incompatible with downstream analyses. Here, we present a novel isolation method employing anionic polysaccharide-modified filter papers for the isolation of EVs (AppiEV) via electrostatic adsorption. A disc of glass fiber-based filter modified with sodium alginate was assembled into a spin column to function as the solid capture phase. In the acidic condition, EVs were induced to carry more positively charged ions, which enable the capture of EVs by the negatively charged filter paper. After a wash, the EVs were released from the spin column using an alkaline elution buffer, which induces the EVs to carry more negative charges. The EVs isolated by AppiEV from cell culture supernatants, plasma, and urine are similar to or even better than those isolated by ultracentrifugation in terms of EV size distribution, protein distribution, and nucleic acid contents. Due to the interference removal of the EV-free RNA and DNA attributed to the negatively charged capture medium, the eluate of AppiEV could be directly used for genetic analysis, including the stem-loop RT-PCR analysis of miR-21 and the allele-specific PCR analysis of mutation genes of EGFR p.L858R and EGFR p.T790M. We believe that AppiEV offers a simple and efficient approach for the isolation of high-quality EVs from various liquid specimens.

Development of a schwarzite-based moving bed 3D printed water treatment system for nanoplastic remediation.

The impact of micro and nanoplastic debris on our aquatic ecosystem is among the most prominent environmental challenges we face today. In addition, nanoplastics create significant concern for environmentalists because of their toxicity and difficulty in separation and removal. Here we report the development of a 3D printed moving bed water filter (M-3DPWF), which can perform as an efficient nanoplastic scavenger. The enhanced separation of the nanoplastics happens due to the creation of a charged filter material that traps the more surface charged nanoparticles selectively. Synthetic contaminated water from polycarbonate waste has been tested with the filter, and enhanced nanoplastic removal has been achieved. The proposed filtration mechanism of surface-charge based water cleaning is further validated using density function theory (semi-empirical) based simulation. The filter has also shown good structural and mechanical stability in both static and dynamic water conditions. The field suitability of the novel treatment system has also been confirmed using water from various sources, such as sea, river, and pond. Our results suggest that the newly developed water filter can be used for the removal of floating nanoparticles in water as a robust advanced treatment system.