Charge Accumulation Characteristics Research Articles

Impact of Pressure and Temperature on Charge Accumulation Characteristics of Insulators in Direct-Current Gas-Insulated Switchgear

Direct-current gas-insulated switchgear (DC GIS) is an important device for promoting the lightweight and compact design of offshore wind power platforms. Gas pressure and temperature gradients are crucial factors that must be considered during the design process of the DC GIS. In this study, the multi-physics coupling model of basin insulators considering surface charge accumulation was established, and the corresponding real-sized insulator surface charge measurement platform was constructed. The effects of gas pressure and temperature gradient on the surface charge accumulation characteristics were investigated, respectively. The results show that the effect of gas pressure on the surface charge distribution characteristics depends on the dominant mode of surface charge. When volume conduction is dominant, the effect of gas pressure on the surface charge is negligible. However, when gas conduction is dominant, the accumulation of a uniform charge pattern on the insulator surface increases with the rise in gas pressure. Furthermore, due to gas convection, the temperature of the upper part of the DC GIS is significantly higher than that of the lower part, which leads to a temperature difference between the upper and lower surfaces of the insulator. The charge density on the insulator upper surface near the central conductor rises with the increase in load current.

Study on space charge accumulation characteristics of silicone elastomer under DC voltage

Study on space charge accumulation characteristics of silicone elastomer under DC voltage

Assessing charge accumulation and flashover phenomena on silicone rubber surface exposed to salt-containing droplets under direct current voltage

In damp and salt-fog environments, silicone rubber composite insulators are prone to forming dispersed droplets that absorb airborne salt nuclei, leading to charge accumulation and potentially causing flashovers that threaten transmission line stability. Regrettably, these concerns have not yet received sufficient attention from relevant researchers. This study examines the surface charge accumulation and flashover characteristics of silicone rubber insulators with droplets of varying electrical conductivity. The droplets can fix charges, as the conductivity of droplets on insulator surfaces increases, the migration rate of surface charges accelerates, causing distortion of the electric field and a significant increase the area of high-density charge regions on the sample surface. Compared with dry surfaces, increasing the equivalent salt density of salt-containing droplets attached to the surface from mild to severe (with conductivity increasing from 800 μS/cm to 2800 μS/cm) leads to a 25 %-40 % increase in the average surface charge density. After adsorbing charges, the salt droplets shorten the discharge development path, making it easier to trigger interface discharge. Compared with dry surfaces, the average flashover voltage of the salt droplets is reduced by at least 30 %. This study offers valuable analysis on charge accumulation and flashover for silicone rubber insulators in salt-fog environments.

Different Charge Accumulation Characteristics on Spacer Upper and Lower Surfaces: Impact of Thermal Convection

Different Charge Accumulation Characteristics on Spacer Upper and Lower Surfaces: Impact of Thermal Convection

Characteristics of Space Charge Accumulation Under Unipolar Square Wave Voltage

Characteristics of Space Charge Accumulation Under Unipolar Square Wave Voltage

Characteristics of Surface Charge Accumulation on Spacers and Its Influencing Factors

Charge accumulation usually happens on the surface of spacers under DC operation, which is susceptible to inducing surface flashover. In order to explore the surface charge accumulation mechanisms and the influences of dielectric conductivity, gas ion mobility, and temperature field on the surface charges, a time-varying charge density model at the gas–solid interface of spacers was established. The results of the simulation show that the discontinuity of the current density between the spacer bulk side and the gas ion flow is the fundamental reason for the charge accumulation on the spacer surface. Additionally, the value of current density fluxes at the interface continues to decrease with the change of the electric field, and the progress of charge transfer gradually stabilizes. Moreover, the dielectric conductivity directly affects the charge accumulation process, and there is a critical conductivity in which the effect of charge conduction in dielectrics counteracts that of gas-phase charge deposition, theoretically. When the conductivity is higher than the critical conductivity, the solid-side charge conduction is the main source of the surface charge accumulation, while the gas-phase charge deposition on the gas side plays a dominant role when the conductivity is lower than the critical conductivity. The charge accumulation is not significantly affected by gas ion mobility when the temperature is evenly distributed. However, under the temperature field with gradient distribution, the current density fluxes at the interface change, causing the polarity reverse of the accumulated charge. In the high-temperature region, the volume current density surges simultaneously with the conductivity, leading to a higher density of surface charge accumulation. Lastly, the design of spacers needs to keep the current densities on both sides of the interface as similar as possible in order to avoid excessive charge gathering in localized areas.

Analysis of interfacial charges in aged co-host emitting layer of organic light-emitting diodes using impedance spectroscopy

This study investigated the charge injection and accumulation characteristics of organic light-emitting diodes (OLEDs) generated by spontaneous orientation polarization (SOP) of organic molecules. SOP enhances the electrical characteristics of OLED devices, such as charge injection and transport, by adjusting the interfacial charge density between the organic layers within the device. An OLED device with a mixed co-host emitting layer was fabricated to examine the degradation effect of SOP after electrical aging. Impedance spectroscopy (IS) revealed the presence of interfacial charges originating from the SOP of small molecules within the electron transport layer (ETL), in both pristine and aged devices. Furthermore, the IS simulation results using equivalent circuits were successfully interpreted based on the electrical properties of each organic layer in the pristine and aged devices. The electrical properties of the ETL, which contained 1,3,5-tris(N-phenyl benzimidazole-2-yl)benzene (TPBi), were degraded, reducing hole accumulation and electron injection.

Study on space charge accumulation characteristics of 320 kV cross-linked polyethylene cable joints

High-Voltage Direct Current (HVDC) cable accessories are the key equipment to connect HVDC cables, and also the weak link in the cable system. In order to investigate the transport characteristics of space charge in cable joints, a two-dimensional axisymmetric cable joint model was established using the bipolar charge transport model, and its space charge and electric field distribution were analyzed through numerical simulation. Furthermore, the effects of the trap depth based on molecular chain displacement and temperature field on interface charge distribution of cable joint were compared with the basic model, respectively. The results show that the stress cone root and the top of the high-voltage shield are easy to accumulate space charges, which will lead to electric field distortion. The trap depth based on molecular chain displacement is larger than that of basic model at the insulation interface, which hinders the charge transport. The model without considering the effect of temperature field accumulates less charge, and the electric field and space charge at the stress cone root and the top of the high-voltage shield change gently with time. The above research results can provide a reference for the design and optimization of cable joints.

Temperature-Dependent Surface Charge Accumulation for Vertical and Horizontal HVDC GIL

In this paper, the heat transfer process of DC gas-insulated transmission line (GIL) is comprehensively considered, including thermal conduction, thermal convection and thermal radiation. An electric-thermal field coupling model is established to characterize the surface charge accumulation characteristics of insulators. The temperature and insulator surface charge density distribution of a 3-D GIL model under different GIL installation ways (i.e. vertical and horizontal GIL) are obtained by finite element software. The results show that: under the identical load current, a large temperature difference (up to 5.7 °C) is shown between both surfaces of vertical GIL insulator, and the temperature on the insulator surface is distributed symmetrically along the center of the insulator. However, the temperature on both surfaces of the horizontal GIL is basically the same, but the temperature distribution varies greatly along the different radial directions of the insulator (up to 5.3 °C). By comparing the surface charge density distribution of insulators under both GIL installation ways, it is found that the surface charge density of horizontal GIL is more than 20% higher than that of vertical GIL. In addition, the volume conductivity distribution of insulator varies greatly under different GIL installation ways. The volume conductivity is positively correlated with the temperature distribution, while the normal electric field on the insulator surface is negatively correlated with volume conductivity distribution. It is hoped that this study can serve as a reference for the design and safe operation of DC GIL.

Study on partial discharge and charge accumulation characteristics of oil‐pressboard insulation under DC superimposed harmonic voltage

AbstractThe oil‐pressboard insulation on the valve side of the converter transformer withstands pulsating square wave voltage. The voltage contains lots of DC components and high‐order harmonics, which is likely to cause insulation failures. The partial discharge and space charge experiments of oil‐impregnated pressboard under DC superimposed harmonic voltage are conducted to study the effects of harmonic frequency and DC components on the discharge and charge accumulation and to explore the correlation mechanism of charge dynamic behaviour and discharge. Firstly, it is found that high‐order harmonic voltage promotes the partial discharge generation, but DC component suppresses the discharge. Moreover, the charge inside the pressboard is mainly injected in the same polarity and accumulates over time. The space charge density near the electrode increases with the increase of harmonic frequency, and the large amount of charge injection leads to electric field distortion. Meanwhile, the electric field direction changes faster, and the frequent charge injection and extraction behaviours make the charge recombination intensify, which promotes the discharge. Through the above analysis, the influence law of harmonic voltage on the failure of oil‐pressboard insulation is obtained, providing a theoretical basis for the structural optimisation and condition assessment of the converter transformer insulation.

An Advanced Ceramic Material for Internal Insulation Used in Gas-Insulated HVDC Apparatus

The traditional polymer insulating material has encountered a bottleneck in improving the surface insulation performance in gas-insulated high voltage direct current (HVDC) apparatus. In this article, an advanced ceramic insulating material is proposed, which has great potential to be utilized in HVDC apparatus. The short-time and long-time surface insulation properties of the ceramic material are researched and compared with those of epoxy composite widely used at present. The conductivity and temperature dependence of the ceramic material is significantly lower than the epoxy composite. The surface charge accumulation and trap evolution characteristics of the ceramic can improve the surface electric field distribution. The long-time test further verifies its reliability, where the failure probability of the ceramic is 74% lower than that of the traditional material. This work may provide a basis for the application of the ceramic material in gas-insulated HVDC apparatus and may be helpful in understanding the surface insulation failure mechanisms in electro-thermal conditions.

Surface Charge Accumulation Characteristics on DC GIL Three-post Insulators Considering the Influence of Temperature Gradient

Surface Charge Accumulation Characteristics on DC GIL Three-post Insulators Considering the Influence of Temperature Gradient

Space Charge Suppression Method of Insulation Layer of HVDC Cable Based on Semi‐Conductive Shielding Layer Modified by Nitrogen‐Doped Graphene

Space charge accumulation in the cable insulation will cause local electric field distortion, and accelerate the aging of the material. The inner semi‐conductive layer as an important structure of cable will affect the charge injection characteristics in the insulation layer. This work intended to explore the method of modifying the semi‐conductive layer with the Nitrogen‐doped graphene (NG) to suppress the charge accumulation utilizing the super‐smoothness of graphene and electron adsorption of N element. First, the NG is prepared using N‐modified graphene, and the semi‐conductive layer with different NG content is fabricated. Second, the physical and chemical properties of the semi‐conductive composite are carried out, then the charge accumulation characteristics in the insulation layer under the effect of the semi‐conductive layer are characterized. The results showed that an appropriate amount of NG doping can significantly inhibit the charge accumulation in the insulation layer. The surface roughness decreased by about 32.13% when the doped NG content is 0.5 phr. With the increase of NG content from 0 to 1 phr, the accumulation charges inside the insulation layer decreased by about 36.84%. This research provided a new approach for suppressing space charge accumulation in the insulation material of high voltage cable.

Analysis of Influence Factors on Space Charge Accumulation Characteristics of 320 kV XLPE Cable

Analysis of Influence Factors on Space Charge Accumulation Characteristics of 320 kV XLPE Cable

Polishing Orientation Affecting Surface Charging and Flashover Characteristics of GIL/GIS Epoxy Spacer

In this article, the influence of polishing orientation on surface charge accumulation and flashover characteristics of the basin spacer in a downsized dc-gas insulated transmission line (GIL) are explored by experiments. Results show that the surface charge distribution of the polished spacers is different from the untreated one. Heteropolar charges can be observed in the polished area and outward expansion area under prestressing condition. The flashover voltages of all polished spacers are decreased. The radial polishing (RP) has the greatest impact on the flashover voltage, and the flashover voltage of the radially polished spacer is decreased by 11% under positive prestressing condition. The metal dust adsorptions of the spacers are also measured, which shows that the radially polished spacer is easier to absorb metal dust and the metal dust diffuses in the radial direction. SEM and energy spectrum scanning of different spacers show that there are more exposed alumina particles on the surface of the polished area. The microdischarge induced by alumina particles is the source of heteropolar charges. When the polished area of the spacers is repaired with epoxy paint, heteropolar charges disappear on the surface of the repaired spacer. It is confirmed that charge accumulation and flashover along the spacer surface are mainly affected by the change of surface morphology on the polished area.

Investigation of the Space Charge Accumulation Characteristics of the Fluorinated Polymer under Electron Beam Irradiation using the Non-contact Type Electrode

Investigation of the Space Charge Accumulation Characteristics of the Fluorinated Polymer under Electron Beam Irradiation using the Non-contact Type Electrode

Transport Characteristics of Interfacial Charge in SiC Semiconductor-Epoxy Resin Packaging Materials.

The silicon carbide (SiC) wide bandgap (WBG) semiconductor power device has been widely applied for its excellent properties. However, the charge accumulated in the interface of SiC semiconductor-related insulation packaging may lead to serious material performance degradation and failure, threatening the reliability and operation life of power devices. In this research, interface charge accumulation characteristics of SiC–epoxy resin double-layered material were investigated, and space charge injection, transport, and accumulation mechanisms, as well as the related temperature effect for the SiC–epoxy resin under polarization and depolarization conditions, were studied by the pulsed electro-acoustic (PEA) technique. The results show that a charge peak appears between the SiC–epoxy resin interface, which shows the same polarity as the SiC side electrode. Charge injects from the SiC electrode, transports along with the SiC semiconductor bulk due to the high mobility, and is blocked by the interface barrier. In addition, under high temperature and high electrical stress conditions, obvious charge accumulation occurs inside the epoxy resin bulk, which was captured by the deep traps. The charge accumulation of the SiC-insulation packaging material can influence the operation of the power device and should attract more attention.

Charge accumulation and dissipation characteristics of rGO / CNTs / EP composite coating

Charge accumulation and dissipation characteristics of rGO / CNTs / EP composite coating

Influence of shape effect on dynamic surface charge transport mechanism of cellular electret after corona discharge

Surface charge accumulation and transport on cellular polypropylene play an important role in nanogenerators, which could have a potential impact on energy harvesting and wearable devices for zero carbon energy systems and the internet of things. Different shapes have different charge accumulation and decay characteristics of the polymer. Therefore, we studied the influence of the sample’s shape on the surface charge decay by experiment and modeling. The surface potential of square and circular cellular polypropylene was measured by a two-dimensional surface potential measurement system with electrostatic capacitive probe. The experimental result shows that the surface potential distribution of the square sample dissipates non-uniformly from the bell shape to a one-sided collapsed shape, while that of the circular sample dissipates uniformly from the bell shape to the crater-like shape. Moreover, the simulated results of the initial surface potential distributions of the square and circular cellular polypropylene are consistent with the experimental results. The investigation demonstrates that the charge transport process is correlated with the shape of the sample, which provides significant reference for designing electret material used for highly efficient nanogenerators.

Surface forward and backward discharges and corresponding residual charge accumulation characteristics under positive impulse

The backward discharge induced by residual charge has attracted considerable attention, but the complex mechanism requires further investigation. This article analyzes the surface discharge and the residual surface charge accumulation characteristics in atmospheric air under a positive impulse. The photographic figure method, the dust figure method, and the electrostatic probe method are employed, allowing the residual charge distribution to be quantitatively determined. One main forward discharge is observed at the impulse front and several subsequent backward discharges are observed at the impulse tail. The propagation length of the forward streamer is closely related to the voltage at the moment of discharge. A model illustrating the evolution process of surface forward and backward discharges as well as the corresponding residual charge accumulation characteristics is established. The residual surface charge plays a significant role in the development of the streamer discharge. The backward discharge is incurred by the positive charge that is deposited by the previous forward discharge.