Characterization Of Core-shell Nanoparticles Research Articles

Synthesis and characterization of core-shell nanoparticles and their application in dental resins

The aim of this study was to synthesize acrylic core-shell particles and silica-loaded core-shell hybrid particles through emulsion polymerization. Also this work examined the influence of synthesized nanoparticles loading in a Bis-GMA/TEGDMA resin matrix on some mechanical properties of the dental composite resins. Core-shell particles consisting of polybutyl acrylate (PBA) rubbery core and polymethyl methacrylate (PMMA)/polystyrene (PS) shell were synthesized by seeded emulsion polymerization. For preparing the core-shell hybrid particles, first silica particles with diameters of about 68 nm were synthesized based on the Stöber process. Then the surface of silica particles was treated with ɣ-MPS. Afterwards, polymeric shell was coated on silica nanoparticles through emulsion polymerization. The morphology of core-shell particles was examined by SEM/TEM. Mechanical properties (fracture toughness, flexural strength and flexural modulus) of the photo-cured Bis-GMA/TEGDMA dental resins/composites filled with different mass fractions of synthesized nanoparticles were tested, and analysis of variance (ANOVA) was used for the statistical analysis of the acquired data. Formation of glassy shell on PBA core in core-shell particles, grafting of ɣ -MPS onto the silica particles and encapsulation of modified silica by polymeric shell in core-shell hybrid particles were confirmed using various analytical techniques. The results of mechanical tests showed that fracture toughness of Bis-GMA/TEGDMA dental resins improved about 35% by the inclusion of 5 wt% silica-loaded core-shell hybrid particles with little effect on flexural strength. This study shows that incorporation of proper amount of hybrid core-shell particles in dental composites can improve their fracture toughness and thus may extend their service life.

Preparation and characterization of core‐shell nanoparticles containing poly(chlorotrifluoroethylene‐co‐ethylvinylether) as core

AbstractCore shell latex particles with a glassy core and a low Tg polymeric shell are usually preferred. More so, the glassy core happens to be a fluoropolymer with a shell polymer that helps in processability. We describe here the preparation and characterization of core shell nanoparticles consisting of poly(chlorotrifluoroethylene‐co‐ethylvinylether) as core encapsulated in poly(styrene‐acrylate) copolymer shell using seeded emulsion polymerization method under kinetically controlled monomer starved conditions. Properties of the emulsion using surfactants (fluoro/conventional) and surfactant free conditions were investigated. Average size (100 nm), spherical shape and core–shell morphology of the latex particles was confirmed by dynamic light scattering and transmission electron microscopy. Absence of CF and CCl peaks in X‐ray photoelectron spectroscopy proves that cores are completely covered. Polymerization in the presence of fluorocarbon surfactant was found to give optimum features like narrow size distribution, good shell deposition and no traces of agglomeration. Films of core shell latex particles exhibited improved transparency and enhanced water contact angles thus making them suitable for applications in various fields including coatings. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011

Characterization of core-shell nanoparticles by small angle neutron scattering

The Ni3Si-type nanoparticles dispersed in a mixture of H2O/D2O were characterised by SANS using the contrast variation method. The existence of a core-shell structure in the nanoparticles with a Ni3Si(Al) core and amorphous SiOx shell is confirmed by the SANS measurements. The nanoparticles were produced by extracting precipitates from a bulk Ni-13.3Si-2Al ( at. %) alloy using electrochemical phase separation technique and were pre-characterised by X-ray diffraction and transmission electron microscopy. By comparing the precipitate morphology in the Ni-Si-Al alloy with the extracted nanoparticles in the SANS measurements, it is clearly established that the precipitates shape and size are unaffected by the extraction process and that the amorphous shell forms on top of the particle core. However, the present measurement could not confirm or exclude the presence of H atoms in the shell structure.