Voltage Changes Research Articles

Changes in Farm Supply Voltage Caused by Switching Operations at a Wind Turbine

Renewable electricity sources are now widely used worldwide. Currently, the most common sources are those that use energy contained in biomass, water, sun, and wind. When connected to a medium-voltage grid, individual wind power plants must meet specific conditions to maintain electricity quality. This article presents field study results on the impact of switching operations (turning the power plant on and off) at a 2 MW Vestas V90 wind turbine on the voltage parameters at the connection point of a farm located 450 m from the source. The analysis showed that the wind turbine under study significantly affects customers’ voltage near the source, causing it to increase by approximately 2.5%. Sudden cessation of generation during the afternoon peak causes a 3% voltage fluctuation, potentially affecting equipment sensitive to rapid voltage changes.

Closed-loop control strategy design for Caputo–Fabrizio definition-based fractional-order Boost converters considering parametric uncertainties

This paper proposes a dual closed-loop adaptive PI control system based on parameter identification for Caputo–Fabrizio (C-F) definition-based fractional-order boost converters. First, a C-F definition-based fractional-order model of the Boost converter is derived. Afterward, an online component parameter identification method is proposed to obtain the values and orders of capacitors and inductors in the proposed model. Based on these identified parameters, a dual closed-loop adaptive PI control system considering parametric uncertainties for the Boost converters is designed using the frequency domain analysis method. Finally, simulation validations are conducted. The online parameter identification method can accurately identify the values and orders of capacitors and inductors. The identification error is less than [Formula: see text] for the capacitance value and [Formula: see text] for the other parameters. Moreover, the proposed control system can automatically adjust the parameters with changes in the component parameters, effectively improving the robustness. Compared to traditional PI controllers, when the parameters of components change, the proposed control system can reduce voltage overshoot by [Formula: see text] in the case of sudden changes in the input voltage. These results confirm the efficacy of the proposed online parameter identification method and the dual closed-loop adaptive PI control system.

Efficient voltage control strategy: observability design for multistage DC–DC buck converter

This paper emphasizes the significance of implementing an effective control system to enhance the performance of a three-stage DC–DC buck converter (TDDC). Herein, we present the development of an observer controller (OC) for TDDC, where average modeling of the DC–DC converter was employed alongside an observer algorithm for the OC. The primary focus is on the adoption of an observation topology aimed at enhancing system responsiveness under various conditions, including variable input voltages, reference voltage changes, load fluctuations, integration with photovoltaics, and battery charging. This approach ensures improved stability and performance, addressing the dynamic challenges inherent in such systems. A comparative analysis was conducted on two distinct control topologies for the proposed TDDC system, namely proportional–integral (PI) and advanced OC. Simulink software was used to model and simulate the proposed system. The results demonstrate lower rising and settling times of the TDDC for the OC and PI implementations, respectively. Additionally, the system with the OC eliminates 20% of the overshoot, while the system with OC minimizes the output voltage oscillations from 13% to 2% compared to the PI system. The OC was integrated into the TDDC to enhance system stability and improve the control loops, particularly the third loop. These improvements make the TDDC with OC suitable for application to renewable energy systems, microgrids, telecommunication networks, and electric vehicles, where precise control and stability are essential.

Analyzing negative differential resistance and capacitive effects in SiOx-based resistive switching devices for security applications

In this work, we analyze the negative differential resistance and capacitive effects in SiOx-based resistive switching devices. The cause of the negative differential effect has been investigated through the study of the switching mechanism in the devices. It has been observed that there is a combination of trap-controlled space charge limited conduction and trap-assisted Poole-Frenkel effect in the devices. Trapping and de-trapping of injected electrons in the defects within the silica structure causes the negative differential resistance effect. This characteristic feature can be employed to design chaotic circuits for security applications. In addition, the high electric field developed in the device compared to the applied field during the change of bias voltage from ±5V–0V, results in a capacitor discharge-like effect. This work will be a step forward in achieving the global Sustainable Development Goal of Peace, Justice, and Strong Institutions (SDG 16).

Influence of Hydration and Temperature on the NaxCO2 Based Transducer Voltage

This paper presents an experimental approach to maximizing the voltage generated by NaxCoO2 and improving the overall efficiency of the p-type thermoelectric leg by doping with Na up to x = 0.88. Two samples with different geometries were tested, each measured with and without an additional magnetic field applied in the direction of the temperature gradient. The properties of sodium cobaltite in response to hydration were explored, at temperatures between 300 and 380 K. Water injection boosted the current and power up to 75–100 µW at a temperature of 350–360 K. This power boost can be attributed to an electron-ion fluid flow pattern maintained by the longitudinal thermomagnetic effect and by water molecules forming hydrogen bonds with oxygen atoms in the CoO2 layers, inside the material. An electronic circuit was designed to boost the voltage to the desired level, for three or more sodium cobaltite samples mounted in parallel, and to store the energy in a supercapacitor. The output voltage and resistivity change of sodium cobaltite samples can be readily used as a humidity and temperature-sensing element in a transducer when paired with an appropriate electronic conditioning scheme.

Research of the distribution symmetrical components in an electrical system with a diesel generator at an unsymmetrical load

Purpose. Investigation symmetrical components of current and voltage in microgrid elements with an autonomous synchronous generator of limited power, which works in parallel with a network transformer under the condition of non-metric load. Methodology. During the research, visual programming methods were used in the Simulink/Matlab package, methods of electrical engineering theory in terms of determining symmetrical component currents and voltages in observation branches, methods of synthesizing schemes for replacing elements of electric power systems for symmetrical component currents, methods of data processing and construction diagrams using specialized software tools.. Findings. As a result the analysis known studies, it was established that under the condition of researching low-power generating systems in conditions of asymmetry, insufficient attention is paid to the nature of the asymmetric load. Using the well-known structure of a microgrid, which includes a synchronous generator, a machine load, and an external network transformer, its model was built, in which, by introducing asymmetric loads of various types, a series of experiments was implemented with the registration of voltages and currents of forward, reverse, and zero sequences in the branches of the network. The analysis of the results obtained during the research established that the positive sequence voltage in the case of a change in the active load does not change its level, under the same circumstances, in the case of an active-capacitive and active-inductive load, the voltage change has the opposite character. In the case of increasing asymmetry of an active-inductive nature, the positive sequence voltage decreases, and in the case of an active-capacitive one, it increases. The specified changes in some cases exceed 3%. Positive sequence currents in the case of active load imbalance differ slightly. In the case of a positive sequence current of the transformer, its continuous growth is observed, which in the case of active-capacitive and active-inductive loads exceeds the active one by an average of 1.5 times. Negative sequence currents in the studied model, which are formed by an asymmetrical load, are completely closed to the transformer, causing zero-sequence voltages, and the nature asymmetrical load significantly affects the value of these currents, a 61% increase was noted. Originality. It was established that in a microgrid, which includes a synchronous generator, a machine load, a symmetrical active load of comparable power to the generator, an external network transformer, in addition to the fact of asymmetry caused by an asymmetrical load, the character of an asymmetrical load (active, active-inductive or active-capacitive). Practical value. In the case of using in microgrids devices that provide an increase in the quality of electrical energy, for example, symmetrical devices, it is necessary, in addition to the asymmetry factor, to take into account the natural load that causes the latter.

Pulse current stabilizer with digital control for the power supply system of the plasmatron

Purpose. Solution of theoretical and practical problems on providing digital control of a pulse converter using high-speed microprocessor tools in the output current stabilization mode with provision of a specified duration of transient processes caused by an increase in load voltage and output current astaticity, which allows to obtain significant advantages over analog versions. Methodology. Review of literary and patent sources on the subject, theory of pulse automatic control systems, mathematical modeling of processes in pulse current stabilizers in the MATLAB / Simulink software environment and physical prototyping. Findings. A simulation model of an autonomous power supply system based on a converter using soft switching technology of transistors and an arc load is presented. A control law is synthesized and a model of a pulse current stabilizer is developed. A method is proposed and ways are found to control a pulse current stabilizer that provide a given duration of transients and astatism of the output current. A model of a pulse stabilizer with digital control based on a single-crystal computing module is developed and manufactured. The results of the study confirm the achievement of a finite duration of transient processes caused by a step change in the load voltage, close to 3-4 periods of conversion and output current astaticism. It is shown that the use of a pulse stabilizer using a fully digital control circuit has undeniable advantages over analog systems. Originality. The problem of synthesizing a digital controller for a given control time by the method of desired transfer functions for a soft switching operating converter on an arc load is solved. In addition to the given control time, additional quality requirements in the steady state are provided. Practical value.The use of microprocessor technology makes it possible not only to implement complex and new highly efficient control algorithms for a converter operating in the pulse current stabilizer mode, but also to perform additional functions for overload protection, self-diagnostics and telemetry of pulse converters. The use of this same digital device simultaneously for the purpose of controlling a pulse converter will allow to abandon analog PWM controllers and thereby reduce its own energy consumption and weight and size characteristics, increase the reliability of the functioning of pulse converters in power supply systems as a whole.

Preparation of Self‐Driven Triboelectric Nanosensor Based on Chitosan‐Coated Ti Foil for Detecting Blood Glucose Concentration

The clinical diagnosis of diabetes mellitus typically depends on blood glucose measurements. Many laboratory studies have focused on enzyme–electrode biosensors that require an external power source. In this study, the potential of triboelectric nanogenerators (TENGs) as self‐driven sensors for glucose detection is investigated by utilizing the glucose specificity of glucose oxidase. When immersed in glucose solutions with concentrations ranging from 3.9 to 13.1 mmol L−1, the TENGs exhibit a linear relationship between the glucose concentration and current and voltage changes. These findings suggest that the TENGs developed in this study can effectively function as glucose sensors, providing a foundation for future human blood glucose monitoring applications and demonstrating a promising new approach for biomedical sensor technology.

Obtaining V2(PO4)3 by sodium extraction from single-phase NaxV2(PO4)3 (1 < x < 3) positive electrode materials.

We report on single-phase NaxV2(PO4)3 compositions (1.5 ≤ x ≤ 2.5) of the Na super ionic conductor type, obtained from a straightforward synthesis route. Typically, chemically prepared c-Na2V2(PO4)3, obtained by annealing an equimolar mixture of Na3V2(PO4)3 and NaV2(PO4)3, exhibits a specific sodium-ion distribution (occupancy of the Na(1) site of only 0.66(4)), whereas that of the electrochemically obtained e-Na2V2(PO4)3 (from Na3V2(PO4)3) is close to 1. Unlike conventional Na3V2(PO4)3, when used as positive electrode materials in Na-ion batteries, the NaxV2(PO4)3 compositions lead to unusual single-phase Na+ extraction/insertion mechanisms with continuous voltage changes upon Na+ extraction/insertion. We demonstrate that the average equilibrium operating voltage observed upon Na+ deintercalation from single-phase Na2V2(PO4)3 is increased up to an average value of ~3.70 V versus Na+/Na (thanks to the activation of the V4+/V5+ redox couple) compared to 3.37 V versus Na+/Na in conventional Na3V2(PO4)3, thus leading to an increase in the theoretical energy density from 396.3 Wh kg-1 to 458.1 Wh kg-1. Electrochemical and chemical Na+ deintercalation from c-Na2V2(PO4)3 enables complete Na-ion extraction, increasing energy density.

SCC/PVA Hydrogel with Self‐Healing Capability for Electrochromic Device

AbstractCracking caused by aging or repeated bending can severely affect the lifetime of electrochromic devices. In this work, a self‐healing electrochromic hydrogel was developed with poly (vinyl alcohol) (PVA)‐sodium carboxymethyl chitosan (SCC) semi‐inter transfer network as the matrix, viologen bromide (HPV2+2Br−) as the electrochromic substance, and borax as the cross‐linking agent. The self‐healing properties of hydrogel stem from the dynamic and reversible borate bonds between borax and PVA molecular chains. As the voltage changes, the color of the device transitions from colorless to light purple and then to dark purple. The optical contrast at 600 nm reaches approximately 51 %. At room temperature, the disconnected hydrogel can fully restore its original state after 30 minutes of contact, effectively addressing issues related to cracks and damage in flexible electrochromic devices. This research holds significant implications for enhancing the reliability and stability of flexible electrochromic devices.

Failure analysis of ternary lithium-ion batteries throughout the entire life cycling at high temperature

The operation life is a key factor affecting the cost and application of lithium-ion batteries. This article investigates the changes in discharge capacity, median voltage, and full charge DC internal resistance of the 25Ah ternary (LiNi0.5Mn0.3Co0.2O2/graphite) lithium-ion battery during full life cycles at 45 °C and 2000 cycles at 25 °C for comparison. The batteries before and after cycling were disassembled, and the structure, morphology, interface characteristics, element content of the cathode and anode plates of the battery were characterized. By analyzing the failure factors of the performance of the ternary batteries during the 45 °C cycling, a reaction mechanism for the rapid decline of high-temperature cycling performance of ternary batteries has been proposed. The results show that the performance degradation of the ternary lithium-ion batteries in the whole life operated at high temperature is characterized by slow decline in the initial stage and rapid drop in the latter stage. Further analysis of physical and chemical performance revealed irreversible damage to both the cathode and anode. The dissolution of transition metal ions from the cathode and their deposition on the anode surface catalyze the decomposition of electrolyte solvents to produce a large amount of gas. Gassing, accompanied by the deposition of Li2CO3 and the thickening of SEI, leads to an increase in the internal resistance of the battery. The coupling between gassing and increased internal resistance is responsible for the rapid drop in the performance of the ternary batteries during high-temperature cycling.

Current Stress Minimization Based on Particle Swarm Optimization for Dual Active Bridge DC–DC Converter

Under extended-phase-shift (ESP) control, the current stress of the dual active bridge converter (DAB) is relatively high, which reduces the efficiency of the converter. To solve this problem, a particle swarm optimization (PSO) algorithm based on minimizing the current stress is proposed in this paper. The optimal phase-shift ratio of the DAB converter with ESP control is obtained by using the algorithm’s optimization characteristic. This approach ensures that the converter achieves minimal current stress, thereby enhancing the steady-state performance of the DAB converter. Moreover, in terms of dynamic performance, traditional PI control has poor dynamic response ability when there are sudden changes in load and input voltage. To solve this problem, the voltage dynamic matrix control (DMC) algorithm is introduced to combine with the PSO algorithm to minimize the current stress of the DAB converter under EPS control while enhancing the dynamic response capability of the DAB converter. A simulation model was constructed for comparative validation on MATLAB/Simulink 2019, demonstrating the correctness and effectiveness of the improved control method.

Constructing Hydrangea-Like Iron-Cobalt Phosphides via Boron-Assisted Strategy as an Efficient Catalyst for Water Splitting at High Current Density.

Finding suitable bifunctional catalysts for industrial hydrogen production is the key to fully building a hydrogen energy society. In this study, we present a novel approach to modifying the surface morphology of electrodeposited cobalt phosphide (CoP). Specifically, we have developed a method to create a hydrangea-like structure of bimetallic cobalt-iron phosphide (B-CoFeP@CoP) through ion-exchange and NaBH4-assisted strategies. This catalyst exhibited excellent bifunctional catalytic capability at high current densities, achieving a current density of 500 mA cm-2 at a small overpotential (387 mV for OER and 252 mV for HER). When assembled into an OWS electrolyzer, this catalyst showed a fairly low cell voltage (≈1.88 V) at 500 mA cm-2 current density., Furthermore, B-CoFeP@CoP shows ceaseless durability over 120 h in both freshwater and seawater with almost no change in the cell voltage. A combined experimental and theoretical study identified that the unique hydrangea-like structure provided a larger electrochemically active surface area and more effective active sites. Further analysis indicates that during the OER process, phosphides ensure that bimetallic active sites adsorb more OOH * intermediates and further DFT calculations showed that B-Fe2P and B-Co2P acted as active centers for dissociation of H2O and desorption of H2, respectively, to synergistically catalyze the HER process.

Influence of Connecting Cables on Stator Winding Overvoltage Distribution under High-Frequency Pulse Width Modulation

In the variable frequency motor drive system, because the cable impedance does not match the motor impedance, the reflection wave of the voltage wave will be generated. The superposition of reflected voltage waves can lead to overvoltage at the motor ends, which can damage the insulation structure. In this paper, the equivalent circuit models of cable and stator winding are established, respectively. The overvoltage distribution under different power supply frequencies and cable lengths is simulated and analyzed. The influence mechanism of power supply frequency and cable length on the overvoltage distribution of stator winding are studied. The simulation results show that the overvoltage of the first pulse falling edge will be superimposed on the overvoltage of the second pulse rising edge under high-frequency conditions, resulting in a further increase in the overvoltage. The voltage appears in all coils after the middle of the winding. The ground voltage is up to 1.32 times the input voltage, and the inter-turn voltage is up to 9.2 times the average voltage. The increase in cable length will lead to an increase in ground voltage, but the increase in speed will slow down after exceeding the critical length of 300 m. The maximum ground voltage can reach 1.93 times of the input voltage, which is 3.6% different from the calculation result under ideal conditions. The inter-turn voltage changes with the cable length in an N-shaped manner, up to 185 V. The results of this paper are of great significance to further study the insulation design of generator end input.

Non-volatile Fermi level tuning for the control of spin-charge conversion at room temperature

Current silicon-based CMOS devices face physical limitations in downscaling size and power loss, restricting their capability to meet the demands for data storage and information processing of emerging technologies. One possible alternative is to encode the information in a non-volatile magnetic state and manipulate this spin state electronically, as in spintronics. However, current spintronic devices rely on the current-driven control of magnetization, which involves Joule heating and power dissipation. This limitation has motivated intense research into the voltage-driven manipulation of spin signals to achieve energy-efficient device operation. Here, we show non-volatile control of spin-charge conversion at room temperature in graphene-based heterostructures through Fermi level tuning. We use a polymeric ferroelectric film to induce non-volatile charging in graphene. To demonstrate the switching of spin-to-charge conversion we perform ferromagnetic resonance and inverse Edelstein effect experiments. The sign change of output voltage is derived by the change of carrier type, which can be achieved solely by a voltage pulse. Our results provide an alternative approach for the electric-field control of spin-charge conversion, which constitutes a building block for the next generation of spin-orbitronic memory and logic devices.

Investigating the Performance Optimization of Three‐Quantum‐Well High Electron Mobility Transistor Device: Analyzing Operational Characteristics and Gate Voltage Influence

Quantum well AlGaN/AlN/GaN high electron mobility transistor (HEMT) devices are a unique kind of semiconductor device that make use of a heterostructure made up of layers of different materials. In this study, the operational characteristics and performance optimization of HEMT devices, with a specific emphasis on the behavior of three‐quantum‐well (3QW) HEMT devices, are explored. The impact of gate voltage is explored and is observed that higher gate voltages result in lower pinch‐off voltages and higher saturation drain currents. In these findings, valuable insights for optimizing circuit designs and ensuring dependable operation across a range of electronic applications are offered. In addition, In this study, the device's ability to detect changes in gate voltage and its nonlinear characteristics is emphasized, providing valuable information for improving the device's performance. Additionally, the benefits of HEMT devices with negative threshold voltages are explored. Devices utilizing AlGaN/AlN/GaN structures demonstrate exceptional performance characteristics, such as rapid switching capabilities, high energy efficiency, and low noise performance, making them well suited for a wide range of scientific and technological applications. Finally, when comparing a QW HEMT device at different drain bias conditions (Vd = 1 V and Vd = 5 V), noticeable variations suggesting improved performance with higher drain bias.

Analysis of Control Strategy Based on P&amp;G Algorithm for the Switching Component of Wireless Solar Power Transfer

Previous researchers have studied wireless power transfer (WPT), while the current study focused on converting DC voltage to AC voltage on the transmitting coil and transferring it to the receiving coil. Previous studies did not discuss the control technique to drive the switching component on the converter circuit, especially the change controller in DC voltage and current affecting the WPT performance. This paper discussed a control strategy based on the P&amp;O algorithm for driving MOSFETs on the half H-bridge inverter of a wireless solar power transfer (WSPT) system. This system is constructed by PV modules as the main DC voltage source, a control strategy based on the perturb and observe (P&amp;O) algorithm, a half H-bridge inverter, and a transmitting and receiving circuit. The WSPT system was modelled using MATLAB SIMULINK with various solar irradiance, and its performance was assessed. The results show that the change in the total output voltage and power of PV modules can be controlled by the P&amp;O algorithm as the signal input of the PWM generator applied to drive the MOSFETs. There are no transient values of voltage waveform on the transmitting and receiving circuit when the transient total output voltage of PV modules occurs. It indicates that the P&amp;O algorithm can effectively manage the PWM generator for its input signal, including the total output voltage and current produced by PV modules.

A hosting capacity based approach toward distribution system planning for high PV penetration

This paper presents an approach to estimate the hosting capacity for distribution networks considering the impact of PV penetration at different voltage levels. The estimation and the method were selected such that the results were most suitable for distribution system planning. A time-series based method was used as it covers significant aspects needed for prioritising network reinforcement. The MV background voltage was modelled varying in time, assuming the same penetration level in the other LV networks supplied by the same MV system. The hosting capacity is defined as the maximum acceptable PV size per customer for a given PV penetration. Based on the different possible combinations of PV location, the probability of overvoltage and overloading is used as a performance index. The planning risk is used as a limit for the performance criterion. The method can be automated for a large number of networks due to using an IEC 61970-based input format. It also enables linking DSO network models to customer smart metre databases. The severity and risks of limit violations are analysed with different metrics from the time-series simulations. The change in background voltage with increasing penetration is shown to impact the results significantly. When considering it, the estimated hosting capacity was reduced by 32 %, on average.

Generation of femtosecond spin-polarized current pulses at Fe/MgO interface by quasi-static voltage

The generation of short spin-current pulses is essential for fast spintronic devices. So far, spin current pulses are generated by femtosecond laser pulses which drive spins from a ferromagnetic metal layer. However, the need for miniaturization, simplicity and energy efficiency favour electric-field control of spintronic devices over optic or thermal control. Here, we combine ab initio calculations of electronic density of states at MgO/Fe interface with continuous model for charge transport to investigate the dynamics of the spin-dependent potential. We demonstrate that the voltage-driven instability of the electronic band structure due to the electronic resonant states at the Fe/MgO interface results in the generation of the femtosecond spin-polarized current pulse with the spin polarization up to P=7 00 % that propagates from the interface to the bulk. The dynamics of the current pulses driven by the Stoner instability depends neither on the dielectric relaxation time nor on the details of how the instability is achieved by changing the voltage, i.e. as long as the voltage changes are slow (quasi-static) with respect to the time determined by the spin diffusion constant, being of the order of fs. The presence of the instability can be detected by THz time-domain spectroscopy or pump-probe techniques.

Revealing the mechanism of bifunctional PtLa electrocatalyst for highly efficient methanol oxidation, hydrogen evolution, and coupling reaction

The development of clean energy solutions, such as fuel cells and hydrogen energy, is crucial for addressing the global energy shortage. Platinum (Pt)-based catalysts are widely used in fuel cells and hydrogen energy generation (for example, via water electrolysis). However, reducing the amount of Pt used while maintaining the catalytic performance of such catalysts is essential. Herein, PtLa catalysts (PtxLay/C) doped with rare earth element lanthanum (La) with different Pt/La atomic ratios were synthesized using a simple chemical reduction method, resulting in Pt65La35/C, Pt78La22/C, Pt97La3/C, and Pt100/C. These PtxLay/C catalysts exhibited excellent electrocatalytic activity and stability in methanol oxidation reaction (MOR), hydrogen evolution reaction (HER), and their coupling reaction as MOR||HER under alkaline conditions. The mechanism by which La doping enhances the electrocatalytic properties and stability of Pt-based catalysts was investigated using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), aberration-corrected scanning transmission electron microscopy (AC-STEM), in-situ Fourier transform infrared (FTIR) and operando Raman spectroscopy. For HER, La doping facilitated the adsorption and activation of H2O at Pt sites, improving water dissociation and *OH desorption and reducing Pt poisoning by *OH. This enhances both the catalytic performance and stability of PtxLay/C for HER. Pt78La22/C exhibited a considerably lower overpotential of only 111 mV at 100 mA cm−2 compared to commercial 20 wt% Pt/C (Pt/C-Johnson Matthey (JM)), which requires 153 mV. For MOR, La promotes CO bond cleavage and reduces CO adsorption at the Pt sites, thereby enhancing both the performance and stability of the catalysts. The mass activity (MA) of Pt78La22/C for MOR is 4.44 A mg−1Pt, which is 12.33 times higher than that of Pt/C-JM (0.36 A/mgPt), and surpasses those of Pt65La35/C, Pt97La3/C, and Pt100/C (2.93, 0.24, and 2.91 A mg−1Pt, respectively). Additionally, Pt78La22/C exhibited outstanding catalytic performance for MOR||HER, with a current density of 20 mA cm−2 at 1.030 V, demonstrating good stability with negligible voltage changes after a 15 h chronoamperometry (CA) testing. This study provides a new strategy for synthesizing Pt-based catalysts with enhanced efficiency and low-energy input for HER||MOR.