Changes In Physical Properties Research Articles

The change of physical properties of calcium carbonate nanomaterials cured soil in road substrates

The utilization of appropriate materials to enhance road subgrade’s physical characteristics is crucial for current transportation construction and maintenance. This study proposes a curing method that employs calcium carbonate nanomaterials to address the problem of soil displacement and settlement in roadway subgrades. A method was developed during the study to explore the optimal curing material ratio. Additionally, this study developed a method for testing and analyzing the mechanical properties of soils cured with nanomaterials, including measures of tensile stress, triaxial shear stress, and Moore’s damage envelope. The study demonstrated that the unconfined compressive strength of the soil treated with calcium carbonate nanomaterials was 0.40 MPa after 7 days of curing with a 6% doping of the curing agent. Increasing the doping to 18% resulted in a breaking load of the soil reaching 0.100 kN. Furthermore, the triaxial shear stress–strain curve of the soil exhibited a slope of 264.47 during the linear phase when the curing agent was dosed at 6%. The slope of the linear phase of the stress–strain curve for triaxial shear at 6% curing agent doping was found to be 264.47. The cured soil molar pack line exhibited an internal friction angle of 22.66 degrees at the same curing agent dosage. The displacement analysis of the replacement roadbed with cured soil revealed a maximum observed displacement of only 377 mm after filling the embankment using the study method. The experimental results provide support for the hypothesis of the study, which suggests that the application of calcium carbonate nanoparticles can significantly enhance the physical characteristics of road subgrade.

A Strained Donor‐Acceptor Carbon Nanohoop: Synthesis, Photophysical and Charge Transport Properties

Herein, we report the synthesis of a novel intramolecular donor‐acceptor (D‐A) system ([12]CPP‐8TPAOMe) based on cycloparaphenylenes (CPPs) grafted with eight di(4‐methoxyphenyl)amino groups (TPAOMe) as donors. Compared to [12]CPP, D‐A nanohoop exhibited significant changes in physical properties, including a large redshift (> 78 nm) in the fluorescence spectrum and novel positive solvatofluorochromic properties with a maximum peak ranging from 484 nm to 546 nm. The potential applications of [12]CPP‐8TPAOMe in electron‐ and hole‐transport devices were further investigated, and its bipolar behavior as a charge transport active layer was clearly observed.

A Strained Donor-Acceptor Carbon Nanohoop: Synthesis, Photophysical and Charge Transport Properties.

Herein, we report the synthesis of a novel intramolecular donor-acceptor (D-A) system ([12]CPP-8TPAOMe) based on cycloparaphenylenes (CPPs) grafted with eight di(4-methoxyphenyl)amino groups (TPAOMe) as donors. Compared to [12]CPP, D-A nanohoop exhibited significant changes in physical properties, including a large redshift (> 78 nm) in the fluorescence spectrum and novel positive solvatofluorochromic properties with a maximum peak ranging from 484 nm to 546 nm. The potential applications of [12]CPP-8TPAOMe in electron- and hole-transport devices were further investigated, and its bipolar behavior as a charge transport active layer was clearly observed.

Combined Aerobic Fermentation of Maricultural and Agricultural Solid Waste: Physicochemical Property and Bacterial Community Structure

The large-scale production of maricultural solid waste is not used effectively and has a significant impact on the environment. However, there is no report on the utilization of solid waste in mariculture of maricultural and agricultural solid waste. At present, aerobic composting is a simple and feasible means of waste resource utilization, but it also seriously pollutes the environment. This paper studied the change of physical and chemical properties (T1: solid waste + straw, T2: solid waste + cow dung + straw, T3: solid waste + cow dung + straw + 5% biochar, T4: solid waste + chicken dung + cow dung + straw + 5% biochar) and microbial succession in the composting process (T4: solid waste + chicken dung + cow dung + straw + 5% biochar) and the effect of decomposed products on seed growth. The results showed that the mixed compost of various materials had a good regulating effect on the physical and chemical indexes, and the highest temperature could reach 69.4 °C. Biochar could extend the high temperature period by 1–2 days. The germination indexes of seeds treated with T1–T4 were 75%, 80%, 81%, and 94%, respectively. Through the change of the seed germination index, it could be seen that the bacterial community structure changed significantly during composting. The Chao 1 index and Shannon index showed that the bacterial abundance and diversity index increased and then decreased. The analysis of the bacterial community structure showed that Proteobacteria and Acinetobacter were the main bacteria in composting, and the relative abundance of Proteobacteria was 81.9% at the phyla level. Acinetobacter and Pseudoxanthomonas were the main bacteria in the process of composting. Acinetobacter was the dominant bacteria in the heating stage, with an abundance of 67.2%.

Application of nanoparticles as novel adsorbents in blood purification strategies.

Blood purification therapy for patients overloaded with metabolic toxins or drugs still needs improvement. Blood purification therapies, such as in hemodialysis or peritoneal dialysis can profit from a combined application with nanoparticles. In this review, the published literature is analyzed with respect to nanomaterials that have been customized and functionalized as nano-adsorbents during blood purification therapy. Liposomes possess a distinct combined structure composed of a hydrophobic lipid bilayer and a hydrophilic core. The liposomes which have enzymes in their aqueous core or obtain specific surface modifications of the lipid bilayer can offer appreciated advantages. Preclinical and clinical experiments with such modified liposomes show that they are highly efficient and generally safe. They may serve as indirect and direct adsorption materials both in hemodialysis and peritoneal dialysis treatment for patients with renal or hepatic failure. Apart from dialysis, nanoparticles made of specially designed metal and activated carbon have also been utilized to enhance the removal of solutes during hemoadsorption. Results are a superior adsorption capacity and a good hemocompatibility shown during treatment of patients with toxication or end-stage renal disease. In summary, nanomaterials are promising tools for improving the treatment efficacy of organ failure or toxication. KEY MESSAGES The pH-transmembrane liposomes and enzyme-loaded liposomes are two representatives of liposomes with modified aqueous inner core which have been put into practice in dialysis. Unmodified or physiochemically modified liposomal bilayers are ideal binders for lipophilic protein-bound uremic toxins or cholestatic solutes, thus liposome-supported dialysis could become the next-generation hemodialysis treatment of artificial liver support system. Novel nano-based sorbents featuring large surface area, high adsorption capacity and decent biocompatibility have shown promise in treatment of uremia, hyperbilirubinemia, intoxication, and sepsis. A major challenge of production lies in avoiding changes in physical and chemical properties induced by manufacturing and sterilizing procedures.

Study on the Synthesis of Nano Zinc Oxide Particles under Supercritical Hydrothermal Conditions.

The supercritical hydrothermal synthesis of nanomaterials has gained significant attention due to its straightforward operation and the excellent performance of the resulting products. In this study, the supercritical hydrothermal method was used with Zn(CH3COO)2·2H2O as the precursor and deionized water and ethanol as the solvent. Nano-ZnO was synthesized under different reaction temperatures (300~500 °C), reaction times (5~15 min), reaction pressures (22~30 MPa), precursor concentrations (0.1~0.5 mol/L), and ratios of precursor to organic solvent (C2H5OH) (2:1~1:4). The effects of synthesis conditions on the morphology and size of ZnO were studied. It was found that properly increasing hydrothermal temperature and pressure and extending the hydrothermal time are conducive to the more regular morphology and smaller size of ZnO particles, which is mainly achieved through the change of reaction conditions affecting the hydrothermal reaction rate. Moreover, the addition of ethanol makes the morphology of nano-zno more regular and significantly inhibits the agglomeration phenomenon. In addition to the change in physical properties of the solvent, this may also be related to the chemical bond established between ethanol and ZnO. The results show that the optimum synthesis conditions of ZnO are 450 °C, 26 MPa, 0.3 mol/L, 10 min, and the molar ratio of precursor to ethanol is 1:3.

Influence of Ti-incorporated Zeolite Topology and Pore Condensation on Vapor Phase Propylene Epoxidation Kinetics with Gaseous H2O2.

Vapor-phase propylene (C3H6) epoxidation kinetics with hydrogen peroxide (H2O2) strongly reflects the physical properties of Ti-incorporated zeolite catalysts and the presence of spectating molecules ("solvent") near active sites even without a bulk liquid phase. Steady-state turnover rates of C3H6 epoxidation and product selectivities vary by orders of magnitudes, depending on the zeolite silanol ((SiOH)x) density, pore topology (MFI, *BEA, FAU), and the quantity of condensed acetonitrile (CH3CN) molecules nearby active sites, under identical reaction mechanisms sharing activated H2O2 intermediates on Ti surfaces. Individual kinetic analyses for propylene oxide (PO) ring-opening, homogeneous diol oxidative cleavage, and homogeneous aldehyde oxidation reveal that secondary reaction kinetics following C3H6 epoxidation responds more sensitively to the changes in zeolite physical properties and pore condensation with CH3CN. Thus, higher PO selectivities achieved in hydrophilic Ti-MFI at steady-state reflect the preferential stabilization of transition states for C3H6 epoxidation (a primary reaction) relative to PO ring-opening and oxidative cleavage (secondary reactions) that solvation effects that reflect interactions among condensed CH3CN within pores and the extended pore structure.

Influence of Ti‐incorporated Zeolite Topology and Pore Condensation on Vapor Phase Propylene Epoxidation Kinetics with Gaseous H2O2

Vapor‐phase propylene (C3H6) epoxidation kinetics with hydrogen peroxide (H2O2) strongly reflects the physical properties of Ti‐incorporated zeolite catalysts and the presence of spectating molecules (“solvent”) near active sites even without a bulk liquid phase. Steady‐state turnover rates of C3H6 epoxidation and product selectivities vary by orders of magnitudes, depending on the zeolite silanol ((SiOH)x) density, pore topology (MFI, *BEA, FAU), and the quantity of condensed acetonitrile (CH3CN) molecules nearby active sites, under identical reaction mechanisms sharing activated H2O2 intermediates on Ti surfaces. Individual kinetic analyses for propylene oxide (PO) ring‐opening, homogeneous diol oxidative cleavage, and homogeneous aldehyde oxidation reveal that secondary reaction kinetics following C3H6 epoxidation responds more sensitively to the changes in zeolite physical properties and pore condensation with CH3CN. Thus, higher PO selectivities achieved in hydrophilic Ti‐MFI at steady‐state reflect the preferential stabilization of transition states for C3H6 epoxidation (a primary reaction) relative to PO ring‐opening and oxidative cleavage (secondary reactions) that solvation effects that reflect interactions among condensed CH3CN within pores and the extended pore structure.

Deposition time dependent structural and optical properties of polycrystalline [formula omitted] films

Sputtering-derived InGaZnO4 (IGZO) thin films were grown on quartz substrates and undergone post-deposition annealing at 700 °C for 2hr in N2 ambient. The influence of deposition time or film thickness on the morphological, structural and optical properties of polycrystalline IGZO thin films has been systematically investigated by means of characterization from field-emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), high resolution X-ray diffraction (HRXRD) and ultraviolet–visible–near infrared (UV–Vis–NIR) spectrophotometer. Results of AFM have shown that the root-mean-square (RMS) surface roughness of the IGZO films increases from 0.888 to 2.640 nm as the deposition time is extended from 50 to 250min. Analysis of XRD indicates that all the films are in polycrystalline phase, with crystallites growing into larger size accordingly to increasing deposition time. Appealingly and scarcely ever reported, the XRD diffraction planes can be separated into three domains, such as (0 0 l), (1 0 l) and (1 1 l) with different growth thicknesses. Optical measurement suggests that the optical bandgap have redshifted from 3.55 to 3.31eV at longer deposition time. Related mechanics about the change in physical properties against deposition time have been elaborated in detail. The validity of Swanepoel method, 1983 in deriving the refractive index of thick IGZO films has also been discussed.

Oxidation-induced variations in the physical and fragmentation characteristics of exhaust soot from DMC-diesel blend: Effect of NO presence in the air atmosphere

This study investigated the changes in physical properties (including morphology, primary particle diameter, fractal dimension, and nanostructure) and fragmentation characteristics of exhaust soot from a modern direct injection diesel engine fueled with diesel (D100) and its blend with 7 vol% of dimethyl carbonate (DMC7) during oxidation processes in air and air-NO atmospheres. Soot particles (D100 soot and DMC7 soot) with specific oxidation degrees (0%, 20%, 50%, and 80%) were produced using a thermogravimetric analyzer, then applied to a high-resolution transmission electron microscopy to generate images. The results exhibited that the morphology for D100 soot and DMC7 soot transformed similarly through oxidation, experiencing an increase in fractal dimension, and a decrease in primary particle diameter, while the introduction of NO to the air accelerated these transformations. Additionally, the nanostructure of both soot particles was gradually ordered through oxidation, as evidenced by longer fringe length, narrower separation distance, and lower tortuosity, while DMC7 soot showed lower order degree compared to D100 soot. Interestingly, the ordering processes of soot nanostructure were decelerated as NO was involved in the oxidation process. Furthermore, the aggregate fragmentation rate for both soot particles declined over the oxidation process, while the possibility for primary particle fragmentation increased overall. Moreover, DMC7 soot exhibited significantly lower aggregate fragmentation rate and higher possibility for primary particle fragmentation than D100 soot at the same oxidation stage. This suggests that DMC7 soot is more susceptible to internal oxidation compared to D100 soot. Furthermore, the presence of NO in the air promoted aggregate fragmentation, while reducing the possibility of primary particle fragmentation.

Disaggregation and fibrillation during sol-gel transition of alginate hydrogels

The rheological and morphological characteristics of Ca-crosslinked alginate hydrogels with two different M/G ratios, α-L-guluronate (G)-rich and β-D-mannuronate (M)-rich, each with one alginic acid concentration, were investigated. It was found that the stiffness and elasticity of alginate hydrogels are derived from the thickness and density of the fibril network structures. In aqueous alginate solution, ball-like aggregates of alginates are present. Time-resolved small-angle X-ray scattering and time-domain nuclear magnetic resonance measurements suggest that the disaggregation of alginate aggregates and loose fibrillation occur in the early stage of the sol-gel transition. After these induction stage, direct gelation is finally caused by the formation of the egg-box junction. G-rich alginate hydrogel has a higher stiffness and a thicker and denser fibril network structure than M-rich alginate hydrogel. The former also exhibits faster and more significant changes in physical properties during the sol-gel transition.

Disorder-Broadened Phase Boundary with Enhanced Amorphous Superconductivity in Pressurized In2Te5.

As an empirical tool in materials science and engineering, the iconic phase diagram owes its robustness and practicality to the topological characteristics rooted in the celebrated Gibbs phase law free variables (F) = components (C) - phases (P) + 2. When crossing the phase diagram boundary, the structure transition occurs abruptly, bringing about an instantaneous change in physical properties and limited controllability on the boundaries (F = 1). Here, the sharp phase boundary is expanded to an amorphous transition region (F = 2) by partially disrupting the long-range translational symmetry, leading to a sequential crystalline-amorphous-crystalline (CAC) transition in a pressurized In2Te5 single crystal. Through detailed in situ synchrotron diffraction, it is elucidated that the phase transition stems from the rotation of immobile blocks [In2Te2]2+, linked by hinge-like [Te3]2- trimers. Remarkably, within the amorphous region, the amorphous phase demonstrates a notable 25% increase of the superconducting transition temperature (Tc), while the carrier concentration remains relatively constant. Furthermore, a theoretical framework is proposed revealing that the unconventional boost in amorphous superconductivity might be attributed to an intensified electron correlation, triggered by a disorder-augmented multifractal behavior. These findings underscore the potential of disorder and prompt further exploration of unforeseen phenomena on the phase boundaries.

Tuning structural, dielectric, and ferroelectric properties of BTO-based ceramics through dual-site substitution

Different strategies for tuning the properties of ferroelectric materials have been employed for advancing electromechanical applications. Among several material synthesis techniques explored, site substitution is an effective approach. The present work focuses on Ba1-xCaxSnyTi1-yO3 (BCST) ceramics prepared by solid-state sintering route with different substitution levels (x = 0, 0.05 and y = 0, 0.09). The impact of site substitution on the properties of Barium Titanate (BTO), phase purity, structural analysis, chemical composition, dielectric, and ferroelectric properties have been studied. An ionic radii difference at A-site and B-site substitution is a key factor to achieve significant changes in physical and structural properties. X-ray diffraction patterns ensure the formation of pure phase perovskite structure in all the compositions. Raman spectroscopy indicates Ca substitution not only occurs at the A-site but also within the oxygen octahedra, adversely affecting the properties. Ca and Sn act as strong grain growth inhibitors, leading to a fine-grained and dense microstructure in BCST. While Ca substitution has a limited impact on the Curie temperature (TC), Sn substitution lowers TC in BST (54 °C) and BCST (50 °C) compared to BTO (126 °C). The Sn substitution results in the coexistence of multiple phases (rhombohedral, tetragonal and orthorhombic) in BST, enhancing its properties (ε' = 6118 at RT, Pr = 5.50 μC/cm2, Q11 = 0.060 m4/C2, d*33 = 526 pm/V) in comparison to BTO. These results acknowledge the role of substituents in lattice disruption, paving the way for chemistry-based materials design in the field of dielectric, actuator and energy storage applications.

Gas-bearing prediction in tight sandstone reservoirs based on multinetwork integration

Tight sandstone reservoir gas is an important component of unconventional natural gas exploration and production in China. However, tight sandstone reservoirs have the characteristics of poor lateral continuity, strong vertical heterogeneity, complex lithology, and large changes in physical properties, which means traditional oil and gas evaluation sometimes suffers from low accuracy. Therefore, a method for predicting the gas content of tight sandstone reservoirs is developed. This method selects seismic attributes through Pearson coefficients, combines multiple attribute information, and inputs it into a deep neural network. This study constructed MultipleNet by combining a convolutional neural network, a bidirectional gated neural unit network, and a self-attention mechanism. This network takes advantage of the complementary advantages of the preceding network modules and can more effectively mine information on various seismic attributes and improve gas-bearing prediction accuracy. This method is applied to actual data from a tight sandstone gas exploration area in the Sichuan Basin. Experimental results indicate that the results of well-side predictions using this method are consistent with well data, providing a new approach and perspective for predicting gas bearing in tight sandstone reservoirs.

Link Between Geometrical and Physical Property Changes Along Nankai Trough With Slow Earthquake Activity Revealed by Dense Reflection Survey

AbstractWe examined the possible factors affecting the spatial distribution of very low frequency earthquakes and tremors in the shallow megathrust of Nankai Trough (<30 km) using a dense network of prestack depth migrated profiles at the frontal wedge. Geometrical parameters examined were decollement roughness, taper angle, and underthrust thickness. Physical properties such as effective basal friction (μb) and pore pressure ratio (λ*) were calculated from the taper angle and p‐wave velocity. Regions of low λ* (0.39 ± 0.08) and smooth decollement showed no slow earthquake activity. In contrast, high activity of slow earthquakes was observed in areas with a rough decollement due to the presence of subducted seamounts or bathymetric highs. The low taper angle (3.8°) off Muroto where slow earthquakes also occur translates to a wide zone of low μb (0.21 ± 0.06) and high λ* (0.66 ± 0.06). However, our results also show that slow earthquakes don't always occur in areas with high λ*.

A continuous 18.6–10 ka record of seismic events revealed by Xinmocun lacustrine sediments at Diexi, eastern Tibetan Plateau

Five Ms 7.0 earthquakes (Wenchuan, Yushu, Lushan, Jiuzhaigou and Maudo) have occurred on the eastern Tibetan Plateau since 2008, and > 20 historical earthquakes (Ms ≥ 5.0) have also been recorded, demonstrating the strong seismic activity prevalent in this region. Owing to the geomorphology of the region, consisting of alpine valleys with a lack of Quaternary deposits, it is difficult to conduct paleo-earthquake research through the excavation of trenches. Lacustrine sediments are regarded as the most suitable archives for paleo-earthquake studies because they often comprise a detailed, long-term, and continuous environmental record. To assess the seismic activity of the Diexi, we studied a well-exposed outcrop of Xinmocun lacustrine sediments that included three sections (XMCⅠ (11.5 m), XMCⅡ (5.6 m), and XMCⅢ (11 m)) near Diexi Lake, moving from a lake shore to lake center environment, at the intersection between the Minjiang fault and Songpinggou fault. Taking into account the geodynamic setting of the area and its known tectonic activity, soft-sediment deformation structures, including load and flame structures, injection structures, ball structures, pseudo-nodules, boudinage structures, plunged sediment mixture, liquefied breccia and micro-faults, discovered within the sections are interpreted as seismites. High-resolution grain-size and magnetic susceptibility indicators were used to obtain a continuous record of the changes in physical properties within the three sections enabling the recognition of additional seismic events that did not result in soft-sediment deformation structures. Rapidly deposited layers with underlying soft-sediment deformation structures in the sections record five (XMCI, XMCII and XMCIII) seismic events; these comprise siliciclastic-enriched sandy sediment fluxes from earthquake-triggered landslides or dust of siliciclastic-enriched clastic materials. Isolated rapidly deposited layers (without underlying soft-sediment deformation structures) record 18 (XMCII), 12 (XMCI), and 21 (XMCIII) additional earthquake-induced inputs of detrital material into the lake. Optically stimulated luminescence and 14C dating of the XMCⅠ, XMCⅡ, and XMCⅢ sections indicate continuous sediment deposition from 19.4–9.9 ka, 15.5–10.1 ka, and 18.7–10.6 ka, respectively, and the seismic events recorded in these sections can be cross-correlated within the age error range. Hence, there are a total of 30 seismic events recorded within the Xinmocun sediments during the period 18.6–10 ka, suggests a weakly periodic pattern with an apparent recurrence time of ∼ 280 years. The Minjiang fault and Songpinggou fault are Holocene active faults with a risk of causing strong earthquakes. Due to the Diexi area is located at the intersection of the Minjiang fault and Songpinggou fault, and has frequent seismic activity, suggest a high seismic risk in the future.

Heat-Induced Changes in the Physical Properties of a New Premixed Calcium Silicate-Containing Root Canal Sealer: An In Vitro Study.

This study aimed to examine how heating affects the physical properties of a newly developed premixed calcium silicate-containing sealer (AH Plus Bioceramic Sealer; AHB), in comparison with EndoSequence BC Sealer (ES), AH Plus Jet (AH), and Pulp Canal Sealer. The setting time, flow, and film thickness were tested with or without heating at 100 °C for 30 or 60 s, in accordance with ISO6876:2012 standards. Ultrastructural and elemental analyses were performed with scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Data were analyzed using one-way analysis of variance (ANOVA) with a Tukey post hoc test (α = 0.05). All sealers exhibited significantly shorter setting time and flow after heating at 100 °C for 30 and 60 s (p < 0.05). After heating, AHB showed a significantly higher film thickness compared to that of the other materials (p < 0.05). None of the tested properties of heat-applied AHB and ES met ISO standards, except the setting time in ES. The SEM/EDS results for AHB and ES were not affected by heating. The detected changes in physical properties can negatively impact the performance of premixed calcium silicate-containing sealers, particularly AHB, when warm vertical compaction is employed.

Ecological condition of marine waters in the area of dredging operations of the kashagan field, Kazakhstan

To determine the hydrophysical and hydrochemical parameters of sea water and their changes during dredging works in the north‐eastern part of the Caspian Sea along the Western Approach Route and near/inside block D, islands EPC‐2, EPC‐3, EPC‐4 and island A of the Kashagan field.Measurement of hydrophysical parameters: salinity, temperature, turbidity, dissolved oxygen concentration, electrical conductivity, pH of seawater was carried out using a portable multi‐parameter analyser "Horiba‐U53" directly in the water column. Water transparency was determined using a Secchi disc. The depth of the water layer was determined using a sounder. Hydrochemical investigations were carried out for seven parameters, with all components sampled in the near‐surface and benthic horizons. Water samples were taken using probes or bathometers: BM‐48, GR‐18 or their analogues.Hydrochemical analyses of seawater samples for: biogens (NO2, NO3, NH4, Ntotal, and Ptotal), synthetic surfactants, phenols, hydrocarbons including polyaromatic hydrocarbons (PAHS), heavy metals, chemical oxygen demand (COD) and biochemical oxygen demand (BOD5). These were carried out in laboratory conditions using analytical equipment according to scientifically accepted methods.The data obtained as a result of the research allow us to draw the following conclusion: changes in the amount of suspended sediment in sea water lead to changes in physical and chemical properties of water (increase in turbidity, disturbance of sediment composition and properties), changes in biotopes, deterioration of oxygen regime, optical properties of water and temperature regime.

Soft Materials with Time-Programmed Changes in Physical Properties through Lyotropic Phase Transitions Induced by pH-Changing Reactions.

We present the development of time-programmable functional soft materials. The materials undergo reversible phase transitions between lyotropic phases with different topologies and symmetries, which in turn have very different physical properties: viscosity, diffusion, and optical transparency. Here, this behavior is achieved by combining pH-responsive lyotropic phases made from the lipid monoolein doped with 10% oleic acid, with chemical reactions that have well-defined controllable kinetics: autocatalytic urea-urease and methyl formate hydrolysis, which increase and decrease pH, respectively. In this case, we use small-angle X-ray scattering (SAXS) and optical imaging to show temporally controlled transitions between the cloudy hexagonal phase, which is a two-dimensional (2D) array of cylindrical inverse micelles, and the transparent, highly viscous three-dimensional (3D) bicontinuous cubic phases. By combining these into a single reaction mixture where the pH increases and then decreases again, we can induce a sequential transformation cycle from hexagonal to cubic and back to hexagonal over several hours. The sample therefore changes from cloudy to transparent and back again as a proof-of-concept demonstration for a wider range of soft materials with time-programmable changes in physical properties.

Electrical Resistivity Tomography (ERT) Investigation for Landslides: Case Study in the Hunan Province, China

Electrical resistivity tomography is a non-destructive and efficient geophysical exploration method that can effectively reveal the geological structure and sliding surface characteristics inside landslide bodies. This is crucial for analyzing the stability of landslides and managing associated risks. This study focuses on the Lijiazu landslide in Zhuzhou City, Hunan Province, employing the electrical resistivity tomography method to detect effectively the surrounding area of the landslide. The resistivity data of the deep strata were obtained, and the corresponding geophysical characteristics are inverted. At the same time, combined with the existing drilling data, the electrical structure of the landslide body is discussed in detail. The inversion results reveal significant vertical variations in the landslide body’s resistivity, reflecting changes in rock and soil physical properties. Combined with geological data analysis, it can be concluded that the sliding surface is located in the sandy shale formation. Meanwhile, by integrating various geological data, we can conclude that the landslide is currently in a creeping stage. During the rainy season, with rainfall infiltration, the landslide will further develop, posing a risk of instability. It should be promptly addressed through appropriate remediation measures. Finally, based on the results of two-dimensional inversion, this article constructs a three-dimensional surface morphology of the landslide body, which can more intuitively compare and observe the internal structure and material composition of the landslide body. This also serves as a foundation for the subsequent management and stability assessment of landslides, while also paving the way for exploring new perspectives on the formation mechanisms and theories of landslides.