Cell Specific Perfusion Rate Research Articles

High-density perfusion cultures of the marine bacterium Rhodovulum sulfidophilum for the biomanufacturing of oligonucleotides

Therapeutic oligonucleotides (ONs) are typically manufactured via solid-phase synthesis, characterized by limited scalability and huge environmental footprint, limiting their availability. Biomanufactured ONs have the potential to reduce the immunogenic side-effects, and to improve the sustainability of their chemical counterparts. Rhodovulum sulfidophilum was demonstrated a valuable host for the extracellular production of recombinant ONs. However, low viable cell densities and product titer were reported so far. In this work, perfusion cell cultures were established for the intensification of ON biomanufacturing. First, the perfusion conditions were simulated in 50 mL spin tubes, selected as a scale-down model of the process, with the aim of optimizing the medium composition and process parameters. This optimization stage led to an increase in the cell density by 44 % compared to the reference medium formulation. In addition, tests at increasing perfusion rates were conducted until achieving the maximum viable cell density (VCDmax), allowing the determination of the minimum cell-specific perfusion rate (CSPRmin) required to sustain the cell culture. Intriguingly, we discovered in this system also a maximum CSPR, above which growth inhibition starts. By leveraging this process optimization, we show for the first time the conduction of perfusion cultures of R. sulfidophilum in bench-scale bioreactors. This process development pipeline allowed stable cultures for more than 20 days and the continuous biomanufacturing of ONs, testifying the great potential of perfusion processes.

Biomass specific perfusion rate as a control lever for the continuous manufacturing of biosimilar monoclonal antibodies from CHO cell cultures.

Continuous manufacturing enables high volumetric productivities of biologics such as monoclonal antibodies. However, it is challenging to maintain both high viable cell densities and productivities at the same time for long culture durations. One of the key controls in a perfusion process is the perfusion rate which determines the nutrient availability and potentially controls the cell metabolism. Cell Specific Perfusion Rate (CSPR) is a feed rate proportional to the viable cell density while Biomass Specific Perfusion Rate (BSPR) is a feed rate proportional to the biomass (cell volume multiply bycell density). In this study, perfusion cultures were run at three BSPRs in the production phase. Low BSPR favored a growth arresting state that led to gradual increase in cell volume, which in turn led to an increase in net perfusion rate proportional to the increase in cell volume. Consequently, at low BSPR, while the cell viability and cell density decreased, high specific productivity of 55 pg per cell per day was achieved. In contrast, the specific productivity was lower in bioreactors operating at a high BSPR. The ability to modulate the cell metabolism by using BSPR was confirmed when the specific productivity increased after lowering the BSPR in one of the bioreactors that was initially operating at a high BSPR. This study demonstrated that BSPR significantly influenced cell growth, metabolism, and productivity in cultures with variable cell volumes.

Platform development for high-throughput optimization of perfusion processes-Part II: Variation of perfusion rate strategies in microwell plates.

The biopharmaceutical industry is replacing fed-batch with perfusion processes to take advantage of reduced capital and operational costs due to the operation at high cell densities (HCD) and improved productivities. HCDs are achieved by cell retention and continuous medium exchange, which is often based on the cell-specific perfusion rate (CSPR). To obtain a cost-productive process the perfusion rate must be determined for each process individually. However, determining optimal operating conditions remain labor-intensive and time-consuming experiments, as investigations are performed in lab-scale perfusion bioreactors. Small-scale models such as microwell plates (MWPs) provide an option for screening multiple perfusion rates in parallel in a semi-perfusion mimic. This study investigated two perfusion rate strategies applied to the MWP platform operated in semi-perfusion. The CSPR-based perfusion rate strategy aimed to maintain multiple CSPR values throughout the cultivation and was compared to a cultivation with a perfusion rate of 1 RV d-1. The cellular performance was investigated with the dual aim (i) to achieve HCD, when inoculating at conventional and HCDs, and (ii) to maintain HCDs, when applying an additional manual cell bleed. With both perfusion rate strategies viable cell concentrations up to 50 × 106 cells mL-1 were achieved and comparable results for key metabolites and antibody product titers were obtained. Furthermore, the combined application of cell bleed and CSPR-based medium exchange was successfully shown with similar results for growth, metabolites, and productivities, respectively, while reducing the medium consumption by up to 50% for HCD cultivations.

Optimization of medium with perfusion microbioreactors for high density CHO cell cultures at very low renewal rate aided by design of experiments.

A novel approach of design of experiment (DoE) is developed for the optimization of key substrates of the culture medium, amino acids, and sugars, by utilizing perfusion microbioreactors with 2 mL working volume, operated in high cell density continuous mode, to explore the design space. A mixture DoE based on a simplex-centroid is proposed to test multiple medium blends in parallel perfusion runs, where the amino acids concentrations are selected based on the culture behavior in presence of different amino acid mixtures, and using targeted specific consumption rates. An optimized medium is identified with models predicting the culture parameters and product quality attributes (G0 and G1 level N-glycans) as a functionof the medium composition. It is then validated in runs performed in perfusion microbioreactor in comparison with stirred-tank bioreactors equipped with alternating tangential flow filtration (ATF) or with tangential flow filtration (TFF) for cell separation, showing overall a similar process performance and N-glycosylation profile of the produced antibody. These results demonstrate that the present development strategy generates a perfusion medium with optimized performance for stable Chinese hamster ovary(CHO) cell cultures operated with very high cell densities of 60 × 106 and 120 × 106 cells/mL and a low cell-specific perfusion rate of 17 pL/cell/day, which is among the lowest reported and is in line with the framework recently published by the industry.

Perfusion process for CHO cell producing monoclonal antibody: Comparison of methods to determine optimum cell specific perfusion rate

Over twenty-five years ago, perfusion was applied to mammalian cells to produce therapeutic proteins, mainly sensitive ones. Nowadays, other issues such as process intensification make perfusion attractive again. However, it is a complex process to set up compared to the classical fed-batch approach. In this paper, we compared three culture methods to determine the perfusion process parameters for a CHO cell line producing a monoclonal antibody. The push-to-low (PTL) and perfusion-without-bleeding (PWB) methods were performed in bioreactors equipped with a cell retention device, while the semi-perfusion (SP) method was performed in spin tubes. In our culture conditions, the PTL reference method, performed at steady state, indicated a minimum cell specific perfusion rate (CSPRmin) estimated at 100 pL.cell−1.day−1. The PWB and SP methods led to lower CSPRmin estimations related to lower cell metabolic fluxes. We therefore propose a three-step approach to determine the perfusion parameters: (i) SP screening method to estimate the optimum medium and temperature, then (ii) PWB run to determine both the growth rate and the maximum cell concentration and finally, (iii) the perfusion process can be operated according to the previously determined parameters, with a final adjustment of the CSPRmin.

Intensifying Continuous Production of Gag-HA VLPs at High Cell Density Using Stable Insect Cells Adapted to Low Culture Temperature.

Protein production processes based on stable insect cell lines require intensification to be competitive with the insect cell-baculovirus expression vector system (IC-BEVS). High cell density (HCD) cultures operate continuously, capable of maintaining specific production rates for extended periods of time which may lead to significant improvements in production yields. However, setting up such processes is challenging (e.g., selection of cell retention device and optimization of dilution rate), often demanding the manipulation of large volumes of culture medium with associated high cost. In this study, we developed a process for continuous production of Gag virus–like particles (VLP) pseudotyped with a model membrane protein (influenza hemagglutinin, HA) at HCD using stable insect cells adapted to low culture temperature. The impact of the cell retention device (ATF vs. TFF) and cell-specific perfusion rate (CSPR) on cell growth and protein expression kinetics was evaluated. Continuous production of Gag-HA VLPs was possible using both retention devices and CSPR of 0.04 nL/cell.d; TFF induces higher cell lysis when compared to ATF at later stages of the process (kD = 0.009 vs. 0.005 h−1, for TFF and ATF, respectively). Reducing CSPR to 0.01–0.02 nL/cell.d using ATF had a negligible impact on specific production rates (rHA = 72–68 titer/109 cell.h and rp24 = 12–11 pg/106 cell.h in all CSPR) and on particle morphology (round-shaped structures displaying HA spikes on their surface) and size distribution profile (peaks at approximately 100 nm). Notably, at these CSPRs, the amount of p24 or HA formed per volume of culture medium consumed per unit of process time increases by up to 3-fold when compared to batch and perfusion operation modes. Overall, this work demonstrates the potential of manipulating CSPRs to intensify the continuous production of Gag-HA VLPs at HCD using stable insect cells to make them an attractive alternative platform to IC-BEVS.

Monitoring of amino acids and antibody N-glycosylation in high cell density perfusion culture based on Raman spectroscopy

Raman spectrum based predictive models provide a process analytical technology (PAT) tool for monitoring and control of culture parameters in bioprocesses. Steady-state perfusion cultures generate a relatively stable metabolite profile, which is not conducive to modeling due to the absence of variations of culture parameters. Here we present an approach where different steady-states obtained by variation of the cell specific perfusion rate (CSPR) between 10 and 40 pL/(cell * day) with cell densities up to 100 × 106 cells/mL during the process development provided a dynamic culture environment, favorable for the model calibration. The cell density had no effect on the culture performance at similar CSPR, however a variation in the CSPR had a strong influence on the metabolism, mAb productivity and N-glycosylation. Predictive models were developed for multiple culture parameters, including cell density, lactate, ammonium and amino acids; and then validated with new runs performed at multiple or single steady-states, showing high prediction accuracy. The relationship of amino acids and antibody N-glycosylation was modeled to predict the glycosylation pattern of the product in real time. The present efficient process development approach with integration of Raman spectroscopy provides a valuable PAT tool for later implementation in steady-state perfusion production processes.

N-1 Perfusion Platform Development Using a Capacitance Probe for Biomanufacturing.

Fed-batch process intensification with a significantly shorter culture duration or higher titer for monoclonal antibody (mAb) production by Chinese hamster ovary (CHO) cells can be achieved by implementing perfusion operation at the N-1 stage for biomanufacturing. N-1 perfusion seed with much higher final viable cell density (VCD) than a conventional N-1 batch seed can be used to significantly increase the inoculation VCD for the subsequent fed-batch production (referred as N stage), which results in a shorter cell growth phase, higher peak VCD, or higher titer. In this report, we incorporated a process analytical technology (PAT) tool into our N-1 perfusion platform, using an in-line capacitance probe to automatically adjust the perfusion rate based on real-time VCD measurements. The capacitance measurements correlated linearly with the offline VCD at all cell densities tested (i.e., up to 130 × 106 cells/mL). Online control of the perfusion rate via the cell-specific perfusion rate (CSPR) decreased media usage by approximately 25% when compared with a platform volume-specific perfusion rate approach and did not lead to any detrimental effects on cell growth. This PAT tool was applied to six mAbs, and a platform CSPR of 0.04 nL/cell/day was selected, which enabled rapid growth and maintenance of high viabilities for four of six cell lines. In addition, small-scale capacitance data were used in the scaling-up of N-1 perfusion processes in the pilot plant and in the GMP manufacturing suite. Implementing a platform approach based on capacitance measurements to control perfusion rates led to efficient process development of perfusion N-1 for supporting high-density CHO cell cultures for the fed-batch process intensification.

Shake tube perfusion cell cultures are suitable tools for the prediction of limiting substrate, CSPR, bleeding strategy, growth and productivity behavior

AbstractBACKGROUNDScale‐down models (SDM) are crucial for efficient setting of different experimental conditions in cell culture media‐ or clone‐screening applications and to predict the expected performance in larger bioreactor cultivations. However, the availability of such models for continuous bioprocessing are scarce and hampered by the requirement for proper cell retention in perfusion applications.RESULTSIn this study, perfusion scale‐down models were optimized for increased cell performance in shake tubes by a semi‐continuous operation mode without any instrumental monitoring. A 40 L perfusion bioreactor was simulated with 10 mL shake tubes by daily medium exchange with or without cell bleeding for process fine‐tuning. Specifically, the optimal cell‐specific perfusion rate (CSPR) was efficiently identified using the perfusion SDM. The cellular growth and productivity were nearly identical to those of the large‐scale experiments. The 24‐h interval of metabolite analysis identified the limits of the SDMs and underscores the need for perfusion processes in large‐scale animal cell bioprocesses.CONCLUSIONOptimized perfusion scale‐down models in semi‐continuous operation mode are highly suitable tools to define important process parameters of larger perfusion bioreactor cultures and are predictive of cellular growth and production behavior.

Automation of high CHO cell density seed intensification via online control of the cell specific perfusion rate and its impact on the N-stage inoculum quality

Current CHO cell production processes require an optimized space-time-yield. Process intensification can support achieving this by enhancing the productivity and improving facility utilization. The use of perfusion at the last stage of the seed train (N-1) for high cell density inoculation of the fed-batch N-stage production culture is a relatively new approach with few industry applicable examples. Within this work, the impact of the cell-specific perfusion rate (CSPR) of the N-1 perfusion and the relevance of its control for the quality of generated inoculation cells was evaluated using an automated perfusion rate (PR) control based on online biomass measurements. Precise correlations (R² = 0.99) between permittivity and viable cell counts were found up to the high densities of 100⋅106 c·mL−1. Cells from N-1 perfusion were cultivated at a high and low CSPR with 50 and 20 pL·(c·d)−1, respectively. Lowered cell growth and an increased apoptotic reaction was found as a consequence of the latter due to nutrient limitations and reduced uptake rates. Subsequently, batch cultivations (N-stage) from the different N-1 sources were inoculated to evaluate the physiological state of the inoculum. Successive responses resulting from the respective N-1 condition were uncovered. While cell growth and productivity of approaches inoculated from high CSPR and a conventional seed were comparable, low CSPR inoculation suffered significantly in terms of reduced initial cell growth and impaired viability. This study underlines the importance to determine the CSPR for the design and implementation of an N-1 perfusion process in order to achieve the desired performance at the crucial production stage.

Establishment and optimization of a high-throughput mimic perfusion model in ambr® 15.

To establish an automated high-throughput mimic perfusion scale-down model (SDM) in ambr® 15 system. An optimized SDM for mimic perfusion was developed in ambr® 15 system. Cell retention in ambr® 15 was realized by sedimentation and supernatant removal with a retention rate > 95%. Although the SDM couldn't reach the viable cell density (VCD) at a bench scale bioreactor (BR), it maintained VCD at approximately 30 × 106 cells/mL with a cell bleeding rate estimated theoretically and predicted the cell specific perfusion rate (CSPR). A base-feeding strategy was developed to alleviate the pH drop during sedimentation which would adversely have an impact on cell growth, and showed an apparent cell viability improvement from 79.6% (control) to 90.1% on Day 18. The optimized SDM for mimic perfusion was employed for media screening in two cell lines. A small-scale high-throughput perfusion model in ambr® 15 was developed, optimized to improve cell viability, and as a result, utilized for media screening in two cell lines.

Control of IgG glycosylation in CHO cell perfusion cultures by GReBA mathematical model supported by a novel targeted feed, TAFE

The N-linked glycosylation pattern is an important quality attribute of therapeutic glycoproteins. It has been reported by our group and by others that different carbon sources, such as glucose, mannose and galactose, can differently impact the glycosylation profile of glycoproteins in mammalian cell culture. Acting on the sugar feeding is thus an attractive strategy to tune the glycan pattern. However, in case of feeding of more than one carbon source simultaneously, the cells give priority to the one with the highest uptake rate, which limits the usage of this tuning, e.g. the cells favor consuming glucose in comparison to galactose.We present here a new feeding strategy (named ‘TAFE’ for targeted feeding) for perfusion culture to adjust the concentrations of fed sugars influencing the glycosylation. The strategy consists in setting the sugar feeding such that the cells are forced to consume these substrates at a target cell specific consumption rate decided by the operator and taking into account the cell specific perfusion rate (CSPR). This strategy is applied in perfusion cultures of Chinese hamster ovary (CHO) cells, illustrated by ten different regimes of sugar feeding, including glucose, galactose and mannose. Applying the TAFE strategy, different glycan profiles were obtained using the different feeding regimes. Furthermore, we successfully forced the cells to consume higher proportions of non-glucose sugars, which have lower transport rates than glucose in presence of this latter, in a controlled way.In previous work, a mathematical model named Glycan Residues Balance Analysis (GReBA) was developed to model the glycosylation profile based on the fed carbon sources. The present data were applied to the GReBA to design a feeding regime targeting a given glycosylation profile. The ability of the model to achieve this objective was confirmed by a multi-round of leave-one-out cross-validation (LOOCV), leading to the conclusion that the GReBA model can be used to design the feeding regime of a perfusion cell culture to obtain a desired glycosylation profile.

An Alternative Perfusion Approach for the Intensification of Virus-Like Particle Production in HEK293 Cultures.

Virus-like particles (VLPs) have gained interest over the last years as recombinant vaccine formats, as they generate a strong immune response and present storage and distribution advantages compared to conventional vaccines. Therefore, VLPs are being regarded as potential vaccine candidates for several diseases. One requirement for their further clinical testing is the development of scalable processes and production platforms for cell-based viral particles. In this work, the extended gene expression (EGE) method, which consists in consecutive media replacements combined with cell retransfections, was successfully optimized and transferred to a bioreactor operating in perfusion. A process optimization using design of experiments (DoE) was carried out to obtain optimal values for the time of retransfection, the cell specific perfusion rate (CSPR) and transfected DNA concentration, improving 86.7% the previously reported EGE protocol in HEK293. Moreover, it was successfully implemented at 1.5L bioreactor using an ATF as cell retention system achieving concentrations of 6.8·1010 VLP/mL. VLP interaction with the ATF hollow fibers was studied via confocal microscopy, field emission scanning electron microscopy, and nanoparticle tracking analysis to design a bioprocess capable of separating unassembled Gag monomers and concentrate VLPs in one step.

A two-step procedure for the design of perfusion bioreactors

A two-step procedure for the design and optimization of mammalian cell perfusion cultures for therapeutic protein production, for a given expression system, is developed. The considered operating variables include the cell specific perfusion rate (CSPR), the perfusion rate (P) and the viable cell density (VCD). The procedure is articulated in two steps, each including a reactor operation through which different steady states are explored sequentially. In the first one, a suitable minimum value of the CSPR is found. This can be achieved through two alternative approaches. These include keeping the perfusion rate or the VCD constant, while changing the other so as to decrease the CSPR. Cellular growth and metabolite in- and output rates decrease when minimizing the CSPR resulting in a lower bleed rate and a better process performance. In the second step, steady states at constant CSPR but increasing VCD values are investigated, by properly adjusting the perfusion rate. In this case, the cellular activity remains constant, while the harvest yield and volumetric productivity further increase with higher perfusion rates. The product quality (charge variants, N-linked glycosylation) investigated during both steps of the procedure shows only minor changes among the different steady states. If product quality properties obtained at this point of the procedure are not satisfactory, they have to be fine-tuned in an additional step. As reported previously, the addition of supplements in the feed stream can be applied to induce significant changes in product quality.

Process design and development of a mammalian cell perfusion culture in shake-tube and benchtop bioreactors.

The development of mammalian cell perfusion cultures is still laborious and complex to perform due to the limited availability of scale-down models and limited knowledge of time- and cost-effective procedures. The maximum achievable viable cell density (VCDmax ), minimum cell-specific perfusion rate (CSPRmin ), cellular growth characteristics, and resulting bleed rate at steady-state operation are key variables for the effective development of perfusion cultures. In this study, we developed a stepwise procedure to use shake tubes (ST) in combination with benchtop (BR) bioreactors for the design of a mammalian cell perfusion culture at high productivity (23 pg·cell-1 ·day-1 ) and low product loss in the bleed (around 10%) for a given expression system. In a first experiment, we investigated peak VCDs in STs by the daily discontinuous medium exchange of 1 reactor volume (RV) without additional bleeding. Based on this knowledge, we performed steady-state cultures in the ST system using a working volume of 10 ml. The evaluation of the steady-state cultures allowed performing a perfusion bioreactor run at 20 × 106 cells/ml at a perfusion rate of 1 RV/day. Constant cellular environment and metabolism resulted in stable product quality patterns. This study presents a promising strategy for the effective design and development of perfusion cultures for a given expression system and underlines the potential of the ST system as a valuable scale-down tool for perfusion cultures.

Semi-continuous scale-down models for clone and operating parameter screening in perfusion bioreactors.

Perfusion cell culture, confined traditionally to the production of fragile molecules, is currently gaining broader attention in the biomanufacturing of therapeutic proteins. The development of these processes is made difficult by the limited availability of appropriate scale-down models. This is due to the continuous operation that requires complex control and cell retention capacity. For example, the determination of an optimal perfusion and bleed rate for continuous cell culture is often performed in scale-down bioreactors and requires a substantial amount of time and effort. To increase the experimental throughput and decrease the required workload, a semi-continuous procedure, referred to as the VCDmax (viable cell density) approach, has been developed on the basis of shake tubes (ST) and deepwell plates (96-DWP). Its effectiveness has been demonstrated for 12 different CHO-K1-SV cell lines expressing an IgG1. Further, its reliability has been investigated through proper comparisons with perfusion runs in lab-scale bioreactors. It was found that the volumetric productivity and the CSPRmin (cell specific perfusion rate) determined using the ST and 96-DWP models were successfully (mostly within the experimental error) confirmed in lab-scale bioreactors, which then covered a significant scale-up from the half milliliter to the liter scale. These scale-down models are very useful to design and scale-up optimal bioreactor operating conditions as well as screening for different media and cell lines.

Shift to high-intensity, low-volume perfusion cell culture enabling a continuous, integrated bioprocess.

In order to address the increasing demand for biologics, cell culture intensification using perfusion offers significantly higher productivities while also reducing manufacturing costs, especially when part of an integrated, continuous bioprocess. An initial study of a long-duration perfusion process using a cell-bleed to maintain a target cell density observed a 2.1-fold higher cell-specific productivity and a gradual decline in the culture growth rate when perfused at an overall lower rate. Subsequent studies sought an alternative process that largely reduced the overall volume of media needed by first perfusing at a high cell-specific perfusion rate (CSPR) to support a high cell density followed by continued perfusion at a low CSPR to promote a more productive stationary phase. This high intensity, low-volume perfusion (HILVOP) process achieved cumulative volumetric productivities of 1.5-1.6 g/L/day with two CHO cell lines. When compared to each cell line's respective commercial-ready, fed-batch process, a 3.1-3.8-fold productivity increase was demonstrated while yielding similar product quality. Furthermore, the higher productivity achieved with HILVOP used 6.6-12.3-fold less media than a similarly productive long-duration process. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 34:1472-1481, 2018.

High-cell-density cultivations to increase MVA virus production

Increasing the yield and the productivity in cell culture-based vaccine manufacturing using high-cell-density (HCD) cultivations faces a number of challenges. For example, medium consumption should be low to obtain a very high concentration of viable host cells in an economical way but must be balanced against the requirement that accumulation of toxic metabolites and limitation of nutrients have to be avoided. HCD cultivations should also be optimized to avoid unwanted induction of apoptosis or autophagy during the early phase of virus infection. To realize the full potential of HCD cultivations, a rational analysis of the cultivation conditions of the appropriate host cell line together with the optimal infection conditions for the chosen viral vaccine strain needs to be performed for each particular manufacturing process.We here illustrate our strategy for production of the modified vaccinia Ankara (MVA) virus isolate MVA-CR19 in the avian suspension cell line AGE1.CR.pIX at HCD. As a first step we demonstrate that the adjustment of the perfusion rate strictly based on the measured cell concentration and the glucose consumption rate of cells enables optimal growth in a 0.8 L bioreactor equipped with an ATF2 system. Concentrations up to 57 × 106 cells/mL (before infection) were obtained with a viability exceeding 95%, and a maximum specific cell growth rate of 0.019 h−1 (doubling time = 36.5 h). However, not only the cell-specific MVA-CR19 virus yield but also the volumetric productivity was reduced compared to infections at conventional-cell-density (CCD).To facilitate optimization of the virus propagation phase at HCD, a larger set of feeding strategies was analyzed in small-scale cultivations using shake flasks. Densities up to 63 × 106 cells/mL were obtained at the end of the cell growth phase applying a discontinuous perfusion mode (semi-perfusion) with the same cell-specific perfusion rate as in the bioreactor (0.060 nL/(cell d)). At this cell concentration, a medium exchange at time of infection was required to obtain expected virus yields during the first 24 h after infection. Applying an additional fed-batch feeding strategy during the whole virus replication phase resulted in a faster virus titer increase during the first 36 h after infection. In contrast, a semi-continuous virus harvest scheme improved virus accumulation and recovery at a rather later stage of infection. Overall, a combination of both fed-batch and medium exchange strategies resulted in similar cell-specific virus yields as those obtained for CCD processes but 10-fold higher MVA-CR19 titers, and four times higher volumetric productivity.

Alternating flow filtration as an alternative to internal spin filter based perfusion process: Impact on productivity and product quality.

This article reports the results obtained from comparison of internal spin filter (ISF) and alternating flow filtration (ATF) as cell retention systems, regarding cell growth, volumetric perfusion rate, cell specific perfusion rate and cell productivity in the fermentation process. As expected we were able to reach higher cell densities and to achieve longer runs since ATF systems are known to be less affected by fouling. Volumetric production of the reactor using the ATF system was 50-70% higher than the production achieved using the ISF due to higher cell density and a two-fold increase in the perfusion rate. On the other hand, downstream processing performances were evaluated regarding chromatographic steps yields and productivity and quality attributes of the purified materials. Similar results were obtained for all evaluated systems. The fact that we were able to achieve a 2 working volumes (WV)/day perfusion rate using an ATF system as cell retention device allowed us to virtually double the WV of a 25 L reactor. These results constitute valuable data for the optimization of recombinant protein production in perfusion processes since a two-fold increase in the average production of a manufacturing facility could be easily achieved as long as downstream scale up is possible. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:1010-1014, 2017.

Principles and approach to developing mammalian cell culture media for high cell density perfusion process leveraging established fed-batch media.

Perfusion medium was successfully developed based on our fed-batch platform basal and feed media. A systematic development approach was undertaken by first optimizing the ratios of fed-batch basal and feed media followed by targeted removal of unnecessary and redundant components. With this reduction in components, the medium could then be further concentrated by 2× to increase medium depth. The medium osmolality was also optimized where we found ∼360 mOsm/kg was desirable resulting in a residual culture osmolality of ∼300 mOsm/kg for our cell lines. Further building on this, the amino acids Q, E, N, and D were rebalanced to reduce lactate and ammonium levels, and increase the cell-specific productivity without compromising on cell viability while leaving viable cell density largely unaffected. Further modifications were also made by increasing certain important vitamin and lipid concentrations, while eliminating other unnecessary vitamins. Overall, an effective perfusion medium was developed with all components remaining in the formulation understood to be important and their concentrations increased to improve medium depth. The critical cell-specific perfusion rate using this medium was then established for a cell line of interest to be 0.075 nL/cell-day yielding 1.2 g/L-day at steady state. This perfusion process was then successfully scaled up to a 100L single-use bioreactor with an ATF6 demonstrating similar performance as a 2L bioreactor with an ATF2. Large volume handling challenges in our fed-batch facility were overcome by developing a liquid medium version of the powder medium product contained in custom totes for plug-and-play use with the bioreactor. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:891-901, 2017.