Cell Patterning Technique Research Articles

Engineering solutions for biological studies of flow-exposed endothelial cells on orbital shakers.

Shear stress is extremely important for endothelial cell (EC) function. The popularity of 6-well plates on orbital shakers to impose shear stress on ECs has increased among biologists due to their low cost and simplicity. One characteristic of such a platform is the heterogeneous flow profile within a well. While cells in the periphery are exposed to a laminar and high-velocity pulsatile flow that mimics physiological conditions, the flow in the center is disturbed and imposes low shear stress on the cells, which is characteristic of atheroprone regions. For studies where such heterogeneity is not desired, we present a simple cell-patterning technique to selectively prevent cell growth in the center of the well and facilitate the exclusive collection and analysis of cells in the periphery. This guarantees that cell phenotypes will not be influenced by secreted factors from cells exposed to other shear profiles nor that interesting results are obscured by mixing cells from different regions. We also present a multi-staining platform that compartmentalizes each well into 5 smaller independent regions: four at the periphery and one in the center. This is ideal for studies that aim to grow cells on the whole well surface, for comparison with previous work and minimal interference in the cell culture, but require screening of markers by immunostaining afterwards. It allows to compare different regions of the well, reduces antibody-related costs, and allows the exploration of multiple markers essential for high-content screening of cell response. By increasing the versatility of the 6-well plate on an orbital shaker system, we hope that these two solutions motivate biologists to pursue studies on EC mechanobiology and beyond.

Viscous Fingering as a Rapid 3D Pattering Technique for Engineering Cell-Laden Vascular-Like Constructs.

Tissues are much larger than the diffusion limit distance, so rapidly providing blood vessels to supply embedded cells inside tissues with sufficient nutrients and oxygen is regarded as a major strategy for the success of bioengineered large and thick tissue constructs. Here, a patterning technique, viscous fingering, is developed to bioengineer vascularized-like tissues within a few minutes. By controlling viscosity, flow rate, and the volume of photo-cross-linkable prepolymer, macro- and microscale vascular network structures can be precisely engineered using the Hele-Shaw cell that is designed in this study. After cross-linking, a vascular-like gel with fingering structures is formed between the bottom and top base gels, creating a sandwich-like structure. Cells can be incorporated into the fingers, bases, or both gels. The spreading and growth direction of the embedded cells are successfully controlled and guided by manipulating the physical properties of the fingering and base gels individually. Moreover, fingering is generated, connected, and surrounded prepared cell-laden microgels in base prepolymers to form prevascularized tissue-like constructs. Taken together, the 3D cell patterning technique extends the potential for modeling and fabricating large and stackable vascularized tissue-like constructs for both ex vivo and in vivo applications.

Development of endomyocardial fibrosis model using a cell patterning technique: In vitro interaction of cell coculture of 3T3 fibroblasts and RL-14 cardiomyocytes.

Cardiac functions can be altered by changes in the microstructure of the heart, i.e., remodeling of the cardiac tissue, which may activate pathologies such as hypertrophy, dilation, or cardiac fibrosis. Cardiac fibrosis can develop due to an excessive deposition of extracellular matrix proteins, which are products of the activation of fibroblasts. In this context, the anatomical–histological change may interfere with the functioning of the cardiac tissue, which requires specialized cells for its operation. The purpose of the present study was to determine the cellular interactions and morphological changes in cocultures of 3T3 fibroblasts and RL-14 cardiomyocytes via the generation of a platform an in vitro model. For this purpose, a platform emulating the biological characteristics of endomyocardial fibrosis was generated using a cell patterning technique to study morphological cellular changes in compact and irregular patterns of fibrosis. It was found that cellular patterns emulating the geometrical distributions of endomyocardial fibrosis generated morphological changes after interaction of the RL-14 cardiomyocytes with the 3T3 fibroblasts. Through this study, it was possible to evaluate biological characteristics such as cell proliferation, adhesion, and spatial distribution, which are directly related to the type of emulated endomyocardial fibrosis. This research concluded that fibroblasts inhibited the proliferation of cardiomyocytes via their interaction with specific microarchitectures. This behavior is consistent with the histopathological distribution of cardiac fibrosis; therefore, the platform developed in this research could be useful for the in vitro assessment of cellular microdomains. This would allow for the experimental determination of interactions with drugs, substrates, or biomaterials within the engineering of cardiac tissues.

Adhesive cell patterning technique using ultrasound vibrations

This paper investigated an ultrasound vibration cell patterning technique. The ultrasound cell culture dish consisted of a culture dish with a glass bottom and a glass disc with a piezoelectric ring that generated a resonance flexural vibration mode on the bottom of the dish. The growth of HeLa cells on the dish was observed under ultrasound excitation for 24 h. Large ultrasound vibrations on the dish inhibited the cell growth. The acoustic field was predicted with finite element analysis and it was found that the cell growth depended strongly on both the acoustic field in the culture medium and the vibration distribution of the dish. The ultrasound vibrations did not affect the viability of the cells, and the cell growth could be controlled by the flexural vibration of the cultured dish.

Spatio-Temporal Control of Cellular Dynamics using a Cell-Friendly Photoresist

Many biological processes in multi-cellular organisms are regulated by various dynamic cellular processes. However, classical tissue culture system can only provide static environments where many dynamic events occur randomly, thus mechanistic study of dynamics of cellular dynamics has been limited. To overcome this limitation, we developed new experimental platforms where we can precisely position different types of cells and control their movement by illuminating light to predefined areas. A thin film of a cell-friendly photoresist PDMP (poly(2,2-dimethoxy nitrobenzyl methacrylate-r-methyl methacrylate-r-poly(ethylene glycol) methacrylate) was used. Upon UV exposure, PDMP thin films become soluble in near-neutral aqueous buffers such as PBS and tissue culture media with minimal cytotoxicity. To create micro-patterns on PDMP thin film, microscope projection photolithography (MPP) technique was used. By performing series of MPP on PDMP thin films and sequentially depositing cells on UV-irradiated regions, we could successfully create single cell arrays of adhering cells. Then, various dynamic cellular processes such as cell spreading, adherens junction formation, and collective cell migration were triggered by removing PDMP thin films surrounding cells in single cell arrays by UV illumination. Using this new dynamic cell-patterning technique in conjunction with an automated microscope equipped with a motorized stage, dynamics of each cellular process was imaged in high-throughput manners to collect large amounts of data in a single experiment. This method can be useful for screening drugs targeting dynamic processes of cells.

H-15 培養面接着特性の変換による異種細胞パターニング技術

H-15 培養面接着特性の変換による異種細胞パターニング技術

Liver-cell patterning Lab Chip: mimicking the morphology of liver lobule tissue

A lobule-mimetic cell-patterning technique for on-chip reconstruction of centimetre-scale liver tissue of heterogeneous hepatic and endothelial cells via an enhanced field-induced dielectrophoresis (DEP) trap is demonstrated and reported. By mimicking the basic morphology of liver tissue, the classic hepatic lobule, the lobule-mimetic-stellate-electrodes array was designed for cell patterning. Through DEP manipulation, well-defined and enhanced spatial electric field gradients were created for in-parallel manipulation of massive individual cells. With this liver-cell patterning labchip design, the original randomly distributed hepatic and endothelial cells inside the microfluidic chamber can be manipulated separately and aligned into the desired pattern that mimicks the morphology of liver lobule tissue. Experimental results showed that both hepatic and endothelial cells were orderly guided, snared, and aligned along the field-induced orientation to form the lobule-mimetic pattern. About 95% cell viability of hepatic and endothelial cells was also observed after cell-patterning demonstration via a fluorescent assay technique. The liver function of CYP450-1A1 enzyme activity showed an 80% enhancement for our engineered liver tissue (HepG2+HUVECs) compared to the non-patterned pure HepG2 for two-day culturing.

Controlled Adhesion and Growth of Long Term Glial and Neuronal Cultures on Parylene-C

This paper explores the long term development of networks of glia and neurons on patterns of Parylene-C on a SiO2 substrate. We harvested glia and neurons from the Sprague-Dawley (P1–P7) rat hippocampus and utilized an established cell patterning technique in order to investigate cellular migration, over the course of 3 weeks. This work demonstrates that uncontrolled glial mitosis gradually disrupts cellular patterns that are established early during culture. This effect is not attributed to a loss of protein from the Parylene-C surface, as nitrogen levels on the substrate remain stable over 3 weeks. The inclusion of the anti-mitotic cytarabine (Ara-C) in the culture medium moderates glial division and thus, adequately preserves initial glial and neuronal conformity to underlying patterns. Neuronal apoptosis, often associated with the use of Ara-C, is mitigated by the addition of brain derived neurotrophic factor (BDNF). We believe that with the right combination of glial inhibitors and neuronal promoters, the Parylene-C based cell patterning method can generate structured, active neural networks that can be sustained and investigated over extended periods of time. To our knowledge this is the first report on the concurrent application of Ara-C and BDNF on patterned cell cultures.

Precise cell patterning using cytophobic self-assembled monolayer deposited on top of semi-transparent gold

This paper reports a simple and effective method for cell patterning by using a self-assembled monolayer (SAM)-treated glass surface which is surrounded by semi-transparent gold coated with another type of SAM. Specifically, a hydrophobic SAM, derived from 1-hexadecanethiol (HDT), was coated on the gold surface to prevent cell growth, and a hydrophilic SAM, derived from 3-trimethoxysilyl propyl-diethylenetriamine (DETA), was coated on the exposed glass surface to promote cell growth. The capabilities of this technique are as follows: 1) single-cell resolution, 2) easy alignment of the cell patterns to the structures already existing on the substrate, 3) visualization and verification of the predefined cytophobic/cytophilic pattern prior to cell growth, and 4) convenient monitoring cell growth at the same location for an extended long term period of time. Whereas a number of earlier techniques have demonstrated the single cell resolution, or visualization and verification of the cytophobic/cytophilic patterns prior to cell growth, we believe that our technique is unique in possessing all of these beneficial qualities at the same time. The distinguishing characteristic of our technique is, however, that the use of semi-transparent Cr/Au film allows for convenient brightfield pattern visualization and offers an advantage over previously developed methods which require fluorescent imaging. We have successfully demonstrated the patterning of four different kinds of cells using this technique: immortalized mouse hypothalamic neurons (GT1-7), mouse osteoblast cells (MC3T3), mouse fibroblast cells (NIH3T3) and primary rat hippocampal neurons. This study was performed with a specific ultimate application-the creation of a multi electrode array (MEA) with predefined localization of cell bodies on top of the electrodes, as well as predefined patterns for cell extensions to grow in between the electrodes. With that goal in mind, we have also determined critical parameters for patterning of each of these cell types, such as the minimum size of a cell-adherent island for exclusively anchoring one cell or two cells, as well as the width of the cytophilic pathway between two islands that enables cell extensions to grow, while preventing the anchoring of the cell bodies. Additionally, we have provided statistical analysis of the occupancy for various sizes and shape of cell-anchoring islands. As demonstrated here, we have developed a novel and reliable cell patterning technique, which can be utilized in various applications, such as biosensors or tissue engineering.

The network formation assay: a spatially standardized neurite outgrowth analytical display for neurotoxicity screening

We present a rapid, reproducible and sensitive neurotoxicity testing platform that combines the benefits of neurite outgrowth analysis with cell patterning. This approach involves patterning neuronal cells within a hexagonal array to standardize the distance between neighbouring cellular nodes, and thereby standardize the length of the neurite interconnections. This feature coupled with defined assay coordinates provides a streamlined display for rapid and sensitive analysis. We have termed this the network formation assay (NFA). To demonstrate the assay we have used a novel cell patterning technique involving thin film poly(dimethylsiloxane) (PDMS) microcontact printing. Differentiated human SH-SY5Y neuroblastoma cells colonized the array with high efficiency, reliably producing pattern occupancies above 70%. The neuronal array surface supported neurite outgrowth, resulting in the formation of an interconnected neuronal network. Exposure to acrylamide, a neurotoxic reference compound, inhibited network formation. A dose-response curve from the NFA was used to determine a 20% network inhibition (NI(20)) value of 260 microM. This concentration was approximately 10-fold lower than the value produced by a routine cell viability assay, and demonstrates that the NFA can distinguish network formation inhibitory effects from gross cytotoxic effects. Inhibition of the mitogen-activated protein kinase (MAPK) ERK1/2 and phosphoinositide-3-kinase (PI-3K) signaling pathways also produced a dose-dependent reduction in network formation at non-cytotoxic concentrations. To further refine the assay a simulation was developed to manage the impact of pattern occupancy variations on network formation probability. Together these developments and demonstrations highlight the potential of the NFA to meet the demands of high-throughput applications in neurotoxicology and neurodevelopmental biology.

Fabrication of complex three-dimensional tissue architectures using a magnetic force-based cell patterning technique

We describe the fabrication of three-dimensional tissue constructs using a magnetic force-based tissue engineering technique, in which cellular organization is controlled by magnetic force. Target cells were labeled with magnetite cationic liposomes (MCLs) so that the MCL-labeled cells could be manipulated by applying a magnetic field. Line patterning of human umbilical vein endothelial cells (HUVECs) labeled with MCLs was successfully created on monolayer cells or skin tissues using a magnetic concentrator device. Multilayered cell sheets were also inducible on a culture surface by accumulating MCL-labeled cells under a uniform magnetic force. Based on these results, we attempted to construct a complex multilayered myoblast C2C12 cell sheet. Here, patterned HUVECs were embedded by alternating the processes of magnetic accumulation of C2C12 cells for cell layer formation and magnetic patterning of HUVECs on the cell layers. This technique may be applicable for the fabrication of complex tissue architectures required in tissue engineering.

Application of magnetic force‐based cell patterning for controlling cell–cell interactions in angiogenesis

To investigate the effects of cell-cell interactions on cellular function, the microenvironment surrounding cells should be precisely controlled. Here, we describe a cell patterning technique, which utilizes magnetic force and magnetite nanoparticles. This method was used to develop cell culture arrays for investigation of cell behaviors in angiogenesis. Pin holder devices that contain more than 6,000 pillars on the surface are used for fabricating the cell culture arrays by setting it on a magnet. The magnetically labeled cells were arranged by magnetic distribution. When the human umbilical vein endothelial cells are arranged at 250 microm intervals (5.9 cells/spot), the cells spread toward other cell cluster on adjacent spots in 4.5 h, and formed cord-like structures in 8.5 h. It was shown that cell-cell interactions were successfully investigated using magnetic cell arrangement.

A new technique for primary hepatocyte expansion in vitro

The current application for many potential cell-based treatments for liver failure is limited by the low availability of mature functional hepatocytes. Although adult hepatocytes have a remarkable ability to proliferate in vivo, attempts to proliferate adult hepatocytes in vitro have been less successful. In this study, we investigated the effect of coculture cell type on the proliferative response and the functional activities of hepatocytes. We show, for the first time, a robust proliferative response of primary adult rat hepatocytes when cocultured with mouse 3T3-J2 fibroblasts. Hepatocytes cultured at low density on growth-arrested 3T3-J2 fibroblast feeder layers underwent significantly higher proliferation rates than when cultured on feeder layers made of four other cell types. Increasing colony size correlated with an increase in hepatocellular functions. The proliferating hepatocytes retained their morphologic, phenotypic, and functional characteristics. Using a cell patterning technique, we found that 3T3-J2 fibroblasts stimulate DNA synthesis in hepatocytes by short-range heterotypic cell-cell interactions. When hepatocytes that proliferated in cocultures were harvested and further subcultured either on 3T3-J2 fibroblast feeders or in the collagen sandwich configuration, their behavior was similar to that of freshly isolated hepatocytes. We conclude that adult rat hepatocytes can proliferate in vitro in a coculture cell type-dependent manner, and can be serially propagated by coculturing with 3T3-J2 fibroblasts while maintaining their differentiated characteristics. Our results also suggest that one of the major reasons for the functional differences in hepatocyte cocultures may be due to the different proliferative responses of hepatocytes as a function of coculture cell type. This study provides new insights in the roles of coculture cell types and cell-cell interactions in the modulation of hepatic proliferation and function.

Cell patterning using magnetite nanoparticles and magnetic force

Technologies for fabricating functional tissue architectures by patterning cells precisely are highly desirable for tissue engineering. Although several cell patterning methods such as microcontact printing and lithography have been developed, these methods require specialized surfaces to be used as substrates, the fabrication of which is time consuming. In the present study, we demonstrated a simple and rapid cell patterning technique, using magnetite nanoparticles and magnetic force, which enables us to allocate cells on arbitrary surfaces. Magnetite cationic liposomes (MCLs) developed in our previous study were used to magnetically label the target cells. When steel plates placed on a magnet were positioned under a cell culture surface, the magnetically labeled cells lined on the surface where the steel plate was positioned. Patterned lines of single cells were achieved by adjusting the number of cells seeded, and complex cell patterns (curved, parallel, or crossing patterns) were successfully fabricated. Since cell patterning using magnetic force may not limit the property of culture surfaces, human umbilical vein endothelial cells (HUVECs) were patterned on Matrigel, thereby forming patterned capillaries. These results suggest that the novel cell patterning methodology, which uses MCLs, is a promising approach for tissue engineering and studying cell-cell interactions in vitro.

Dielectrophoresis based‐cell patterning for tissue engineering

Engineering functional tissues and organs in vitro is considered integral to regenerative medicine. Many recent cell patterning technique developments position cells at a pre-designated pattern to improve tissue engineering efficiency and quality and to facilitate 3-D cell-cell interaction exploration. Among these techniques, dielectrophoresis (DEP)-based cell patterning advantageously offers speed, ease of operation, low degree of cell damage, and precision. This article reviews recent advances in DEP-based patterning techniques, including electrode design, suitable buffer and hydrogel, effects of the electric current to cells, combination potential with other techniques, as well as efforts to generate 3-D tissues.

Laser-guided direct writing for three-dimensional tissue engineering

One of the principal limitations to the size of an engineered tissue is oxygen and nutrient transport. Lacking a vascular bed, cells embedded in an engineered tissue will consume all available oxygen within hours while out branching blood vessels will take days to vascularize the implanted tissue. One possible solution is to directly write vascular structures within the engineered tissue prior to implantation, reconstructing the tissue according to its native architecture. The cell patterning technique, laser-guided direct writing (LGDW), can pattern multiple cells types with micrometer resolution on arbitrary surfaces, including biological gels. Here we show that LGDW can pattern human umbilical vein endothelial cells (HUVEC) in two- and three-dimensions with micrometer accuracy. By patterning HUVEC on Matrigel, we can direct their self-assembly into vascular structures along the desired pattern. Finally, co-culturing the vascular structures with hepatocytes resulted in an aggregated tubular structure similar in organization to a hepatic sinusoid. This capability can facilitate studies of tissue architecture at the single cell level, and of heterotypic interactions underlying processes such as liver and pancreas morphogenesis, differentiation, and angiogenesis.

Guided cell patterning on gold–silicon dioxide substrates by surface molecular engineering

We report an effective approach to patterning cells on gold–silicon dioxide substrates with high precision, selectivity, stability, and reproducibility. This technique is based on photolithography and surface molecular engineering and requires no cell positioning or delivery devices, thus significantly reducing the potential damage to cells. The cell patterning was achieved by activating the gold regions of the substrate with functionalized thiols that covalently bind proteins onto the gold regions to guide subsequent cell adhesion while passivating the silicon dioxide background with polyethylene glycol to resist cell adhesion. Fourier transform infrared reflectance spectroscopy verified the successful immobilization of proteins on gold surfaces. Protein patterns were visualized by tagging proteins with Rhodamine fluorescent probes. Time-of-flight secondary ion mass spectrometry was used to characterize the chemistry of both the cell-adhesive and cell-resistant regions of surfaces after each key chemical reaction occurring during the molecular surface engineering. The ability of the engineered surfaces to guide cell adhesion was illustrated by differential interference contrast (DIC) reflectance microscopy. The cell patterning technique introduced in this study is compatible with micro- and photo-electronics, and may have many medical, environmental, and defense applications.

Photolithographically defined deposition of attachment factors as a versatile method for patterning the growth of different cell types in culture.

Spatially defined growth of cells in culture is a useful model for studies ranging from the characterization of cellular motility to the analysis of network behaviour in structurally defined ensembles of excitable cells. Current methodological approaches for obtaining patterned growth include sophisticated modifications of surface chemistry, stamping techniques and microfluidics. The implementation of most of these techniques requires the availability of highly specialized apparatus and some of the methods are specific for certain cell types and/or substrate materials. The goal of the present study was to develop a cell-patterning technique that can be implemented by any laboratory working with cell culture and that is highly adaptable in terms of cell types and substrate materials. The method is based on a photolithographic process that permits the patterned deposition of attachment factors of choice on surfaces previously coated with agar with a spatial resolution (maximal deviation from a straight line) of +/-3 micro m. Because agar efficiently prevents cell adhesion, patterned growth obtained with this technique displays virtually no off-pattern cell attachment. The method permitted the patterning of cardiomyocytes, fibroblasts and HeLa cells on either glass substrates or polymer-coated materials with a spatial resolution of a few micrometers.

UV-Based Patterning of Polymeric Substrates for Cell Culture Applications

We studied the physico/chemical effects of deep UV irradiation of polystyrene, polymethylmethacrylate and polycarbonate with respect to cell adhesion in vitro. Photochemical modifications of the polymer surfaces yielded active peroxide compounds which allowed graft coupling of acrylic monomers (acrylamide, acrylic acid) together with oxidized chemical groups which were identified by X-ray photoelectron spectroscopy, dye binding and contact angle titrations as being mainly carboxylic groups. It was observed that hepatocytes (HepG2, human hepatoma cell line) and fibroblasts (L929, murine cell line) exhibit strong adhesion on the irradiated polymer surfaces. Masked irradiations opened a simple, fast, and economical route to obtain chemically patterned polymeric substrates for structured cell adhesion. This is more advantageous as compared to silane based patterning techniques on glass or thiol based patterning on gold due to the elimination of any chemical treatment, the clean room compatibility and the small size of achieved structures. The described cell patterning technique may become a useful tool for the study of a variety of defined co-cultures (for example hepatocytes and fibroblasts), neuronal networks, intercellular communication, organogenesis and for applications like biosensors or engineered highly functional tissues and implants as bioartificial organs.