Cell Adhesive Peptide Sequence Research Articles

Engineering peptide-modified alginate-based bioinks with cell-adhesive properties for biofabrication.

Alginate (ALG) and its oxidised form alginate-dialdehyde (ADA) are highly attractive materials for hydrogels used in 3D bioprinting as well as drop-on-demand (DoD) approaches. However, both polymers need to be modified using cell-adhesive peptide sequences, to obtain bioinks exhibiting promising cell-material interactions. Our study explores the modification of ALG- and ADA-based bioinks with the adhesive peptides YIGSR (derived from laminin), RRETEWA (derived from fibronectin) and IKVAV (derived from laminin) for 3D bioprinting. Two coupling methods, carbodiimide and Schiff base reactions, were employed to modify the polymers with peptides. Analytical techniques, including FTIR and NMR were used to assess the chemical composition, revealing challenges in confirming the presence of peptides. The modified bioinks exhibited decreased stability, viscosity, and stiffness, particularly-ADA-based bioinks in contrast to ALG. Sterile hydrogel capsules or droplets were produced using a manual manufacturing process and DoD printing. NIH/3T3 cell spreading analysis showed enhanced cell spreading in carbodiimide-modified ADA, Schiff base-modified ADA, and PEG-Mal-modified ADA. The carbodiimide coupling of peptides worked for ADA, however the same was not observed for ALG. Finally, a novel mixture of all used peptides was evaluated regarding synergistic effects on cell spreading which was found to be effective, showing higher aspect ratios compared to the single peptide coupled hydrogels in all cases. The study suggests potential applications of these modified bioinks in 3D bioprinting approaches and highlights the importance of peptide selection as well as their combination for improved cell-material interactions.

Custom-engineered hydrogels for delivery of human iPSC-derived neurons into the injured cervical spinal cord

Cervical damage is the most prevalent type of spinal cord injury clinically, although few preclinical research studies focus on this anatomical region of injury. Here we present a combinatorial therapy composed of a custom-engineered, injectable hydrogel and human induced pluripotent stem cell (iPSC)-derived deep cortical neurons. The biomimetic hydrogel has a modular design that includes a protein-engineered component to allow customization of the cell-adhesive peptide sequence and a synthetic polymer component to allow customization of the gel mechanical properties. In vitro studies with encapsulated iPSC-neurons were used to select a bespoke hydrogel formulation that maintains cell viability and promotes neurite extension. Following injection into the injured cervical spinal cord in a rat contusion model, the hydrogel biodegraded over six weeks without causing any adverse reaction. Compared to cell delivery using saline, the hydrogel significantly improved the reproducibility of cell transplantation and integration into the host tissue. Across three metrics of animal behavior, this combinatorial therapy significantly improved sensorimotor function by six weeks post transplantation. Taken together, these findings demonstrate that design of a combinatorial therapy that includes a gel customized for a specific fate-restricted cell type can induce regeneration in the injured cervical spinal cord.

Design of Recombinant Spider Silk Proteins for Cell Type Specific Binding.

Cytophilic (cell-adhesive) materials are very important for tissue engineering and regenerative medicine. However, for engineering hierarchically organized tissue structures comprising different cell types, cell-specific attachment and guidance are decisive. In this context, materials made of recombinant spider silk proteins are promising scaffolds, since they exhibit high biocompatibility, biodegradability, and the underlying proteins can be genetically functionalized. Here, previously established spider silk variants based on the engineered Araneus diadematus fibroin 4 (eADF4(C16)) are genetically modified with cell adhesive peptide sequences from extracellular matrix proteins, including IKVAV, YIGSR,QHREDGS, and KGD. Interestingly, eADF4(C16)-KGD as one of 18tested variants is cell-selective for C2C12mouse myoblasts, one out of 11 tested cell lines. Co-culturing with B50rat neuronal cells confirms the cell-specificity of eADF4(C16)-KGD material surfaces for C2C12mouse myoblast adhesion.

3D Printing of Antibacterial, Biocompatible, and Biomimetic Hybrid Aerogel-Based Scaffolds with Hierarchical Porosities via Integrating Antibacterial Peptide-Modified Silk Fibroin with Silica Nanostructure.

Scaffold-mediated tissue engineering has become a golden solution for the regeneration of damaged bone tissues that lack self-regeneration capability. A successful scaffold in bone tissue engineering comprises a multitude of suitable biological, microarchitectural, and mechanical properties acting as different signaling cues for the cells to mediate the new tissue formation. Therefore, careful design of bioactive scaffold macro- and microstructures in multiple length scales and biophysical properties fulfilling the tissue repair demands are necessary yet challenging to achieve. Herein, we have developed an antibacterial and biocompatible silica-silk fibroin (SF) gel-based ink through novel yet simple chemical approaches of sol-gel and self-assembly followed by processing the obtained gels as three-dimensional (3D) hybrid aerogel-based scaffolds exploiting the advanced materials design approaches of micro-extrusion-based 3D printing, and directional freeze-casting/drying approaches. As the main constituent of the hybrid biocompatible scaffold of this study, we used the SF extracted from Bombyx mori silkworm cocoon. However, to increase the cell responsivity and bactericidal efficiency of the final scaffold, thiol-ended antimicrobial and cell adhesive peptide sequence (SH-CM-RGD) was conjugated to silica-SF hybrid gels via covalent attachment using a spacer molecule through either preprint (prior to sol-gel) or during the post-printing steps on the previously printed silica-SF gel. In the next step, the hybrid Silica-SF-CM-RGD hydrogel ink was 3D-printed into the construct with interconnected porous structure with hierarchically organized porosity and a combination of several promising properties. Namely, due to the covalent linkage of the antibacterial peptide to the SF, the scaffold shows potent bactericidal efficiency toward Gram-positive and Gram-negative bacteria. Moreover, nanostructured silica components in the 3D-printed composites could intertwine with SF-CM-RGD to support the mechanical properties in the final scaffold and the final osteoconductivity of the scaffold. This study supports the promising properties of 3D-printed silica-SF-based hybrid aerogels constructs for repairing bone defect.

Bicyclic RGD peptides enhance nerve growth in synthetic PEG-based Anisogels.

Nerve regeneration scaffolds often consist of soft hydrogels modified with extracellular matrix (ECM) proteins or fragments, as well as linear and cyclic peptides. One of the commonly used integrin-mediated cell adhesive peptide sequences is Arg-Gly-Asp (RGD). Despite its straightforward coupling mechanisms to artificial extracellular matrix (aECM) constructs, linear RGD peptides suffer from low stability towards degradation and lack integrin selectivity. Cyclization of RGD improves the affinity towards integrin subtypes but lacks selectivity. In this study, a new class of short bicyclic peptides with RGD in a cyclic loop and ‘random screened’ tri-amino acid peptide sequences in the second loop is investigated as a biochemical cue for cell growth inside three-dimensional (3D) synthetic poly(ethylene glycol) (PEG)-based Anisogels. These peptides impart high integrin affinity and selectivity towards either αvβ3 or α5β1 integrin subunits. Enzymatic conjugation of such bicyclic peptides to the PEG backbone enables the formulation of an aECM hydrogel that supports nerve growth. Furthermore, different proteolytic cleavable moieties are incorporated and compared to promote cell migration and proliferation, resulting in enhanced cell growth with different degradable peptide crosslinkers. Mouse fibroblasts and primary nerve cells from embryonic chick dorsal root ganglions (DRGs) show superior growth in bicyclic RGD peptide conjugated gels selective towards αvβ3 or α5β1, compared to monocyclic or linear RGD peptides, with a slight preference to αvβ3 selective bicyclic peptides in the case of nerve growth. Synthetic Anisogels, modified with bicyclic RGD peptides and containing short aligned, magneto-responsive fibers, show oriented DRG outgrowth parallel to the fibers. This report shows the potential of PEG hydrogels coupled with bicyclic RGD peptides as an aECM model and paves the way for a new class of integrin selective biomolecules for cell growth and nerve regeneration.

Rapid and Robust Coating Method to Render Polydimethylsiloxane Surfaces Cell-Adhesive.

Polydimethylsiloxane (PDMS) is a synthetic material with excellent properties for biomedical applications because of its easy fabrication method, high flexibility, permeability to oxygen, transparency, and potential to produce high-resolution structures in the case of lithography. However, PDMS needs to be modified to support homogeneous cell attachments and spreading. Even though many physical and chemical methods, like plasma treatment or extracellular matrix coatings, have been developed over the last decades to increase cell-surface interactions, these methods are still very time-consuming, often not efficient enough, complex, and can require several treatment steps. To overcome these issues, we present a novel, robust, and fast one-step PDMS coating method using engineered anchor peptides fused to the cell-adhesive peptide sequence (glycine-arginine-glycine-aspartate-serine, GRGDS). The anchor peptide attaches to the PDMS surface predominantly by hydrophobic interactions by simply dipping PDMS in a solution containing the anchor peptide, presenting the GRGDS sequence on the surface available for cell adhesion. The binding performance and kinetics of the anchor peptide to PDMS are characterized, and the coatings are optimized for efficient cell attachment of fibroblasts and endothelial cells. Additionally, the applicability is proven using PDMS-based directional nanotopographic gradients, showing a lower threshold of 5 μm wrinkles for fibroblast alignment.

Biofunctionalized Electrospun PCL-PIBMD/SF Vascular Grafts with PEG and Cell-Adhesive Peptides for Endothelialization.

Artificial small-caliber vascular grafts are still limited in clinical application because of thrombosis, restenosis, and occlusion. Herein, a small-caliber vascular graft (diameter 2mm) is fabricated from poly(ε-caprolactone)-b-poly(isobutyl-morpholine-2,5-dione) (PCL-PIBMD) and silk fibroin (SF) by electrospinning technology and then biofunctionalized with low-fouling poly(ethylene glycol) (PEG) and two cell-adhesive peptide sequences (CREDVW and CAGW) with the purpose of enhancing antithrombogenic activity and endothelialization. The successful grafting of PEG and peptide sequences is confirmed by X-ray photoelectron spectroscopy. The suitable surface wettability of the modified vascular graft is testified by water contact angle analysis. The surface hemocompatibility is verified by platelet adhesion assays and protein adsorption assays, and the results demonstrate that both platelet adhesion and protein adsorption on the biofunctionalized surface are significantly reduced. In vitro studies demonstrate that the biofunctionalized surface with suitable hydrophilicity and cell-adhesive peptides can selectively promote the adhesion, spreading, and proliferation of human umbilical vein endothelial cells. More importantly, compared with control groups, this biofunctionalized small-caliber vascular graft shows high long-term patency and endothelialization after 10 weeks of implantation. The biofunctionalization with PEG and two cell-adhesive peptide sequences is an effective method to improve the endothelialization and long-term performance of synthetic vascular grafts.

Multiple Cross-Linking of a Small Peptide to Form a Size Tunable Biopolymer with Efficient Cell Adhesion and Proliferation Property.

Development of biocompatible polymeric systems capable of cell adhesion and proliferation is a challenging task. Proper cross-linking of small cell adhesive peptide sequences is useful in this respect as it provides the inherent nontoxic environment as well as the cross-linked polymeric network to the cells for adhesion and proliferation. A multiple cross-linking strategy is applied to create a peptide-based cross-linked polymer. Covalent linkage through disulfide bond formation, supramolecular linkage using homoternary complexation by CB[8], and enzymatic cross-linking by HRP-mediated dimerization of tyrosine are used to prepare the cross-linked, peptide-based polymer decorated with cell-adhesive RGDS sequence. The supramolecular cross-linking via CB[8] provided stability as well as brings the RGDS sequences at the surface of the polymer particles. The order of cross-linking allowed to fine-tune the particle size of the polymer and polymer particles of wide range (200-1000 nm) can be prepared by varying the order. The cross-linked polymer particles (P1 and P2) were found to be stable at wide range of temperature and pH. Moreover, as intended, the polymer was noncytotoxic in nature and showed efficient cell adhesion and proliferation property, which can be used for further biological applications.

Effect of changes in the surface chemistry and topography of poly(2-hydroxyethyl methacrylate) on the in vitro attachment of human corneal epithelial cells

The effects on cell adhesion induced by changes in the topography and chemistry of poly(2-hydroxyethyl methacrylate) hydrogel surfaces were investigated in vitro using the human corneal epithelial cell line, HCE-T. Poly(2-hydroxyethyl methacrylate) surfaces with a lotus-leaf-like topography and poly(2-hydroxyethyl methacrylate) surfaces with a flat topography, but functionalized with the cell-adhesive peptide sequence Arg-Gly-Asp, both enhanced attachment of HCE-T cells as compared to flat, non-functionalized poly(2-hydroxyethyl methacrylate) surfaces. However, the simultaneous existence on the same poly(2-hydroxyethyl methacrylate) surface of Arg-Gly-Asp motifs and of lotus-leaf-like topographical patterns led to an apparently antagonistic effect reflected in reduced cell attachment. The study provided additional evidence of the complexity of the cell-biomaterial interactions.

Thermoresponsive and Active Functional Fiber Mats for Cultured Cell Recovery.

Thermoresponsive and active functional fiber mats were prepared from random copolymer of poly(pentafluorophenyl acrylate-co-N-isopropylacrylamide) (P(PFPA-co-NIPAM)), which was synthesized by a controlled radical polymerization process based on reversible addition-fragmentation chain transfer (RAFT). As reactive sites, pentafluorophenyl ester (PFP) groups were incorporated in the copolymer to allow for a multiple post-polymerization modification. UV-cross-linkable moieties were first introduced by partially reacting PFP groups in the copolymer with ortho-nitrobenzyl (ONB)-protected diamine. Electrospinning the resulting ONB-containing P(PFPA-co-NIPAM), followed by UV-induced cross-linking, yielded stable cross-linked thermoresponsive PNIPAM-based fiber mats. The remaining PFP active groups on the surface of copolymer fiber mats allowed for further conjugation with an H-Gly-Arg-Gly-Asp-Ser-OH (GRGDS) peptide, a well-known cell adhesive peptide sequence that was selected as a model in order to promote cell growth. At 37 °C, fibroblast cells were found to attach, spread, and proliferate well on the GRGDS-immobilized cross-linked (CL) fiber mat, as opposed to those on the GRGDS-immobilized un-cross-linked (UCL) fiber mat. By decreasing the temperature down to 20 °C, i.e. below the lower critical solution temperature (LCST) of thermoresponsive PNIPAM, cultured cells could easily be released from both GRGDS-immobilized CL and UCL fiber mats, whereas no cells were detached from tissue culture polystyrene (TCPS). These results suggest that the thermosensitive and active functional fiber mat obtained in this research represent an attractive and versatile platform for cultured cell recovery, which is beneficial for tissue engineering applications.

Tuning of Cell–Biomaterial Anchorage for Tissue Regeneration

Which mechanisms mediate cell attachment to biomaterials? What role does the surface charge or wettability play on cell-material anchorage? What are the currently investigated strategies to modify cell-matrix adherence spatiotemporally? Considering the development of scaffolds made of biocompatible materials to temporarily replace the structure and/or function of the extracellular matrix, focus is given to the analysis of the specific (i.e., cell adhesive peptide sequences) and unspecific (i.e., surface charge, wettability) mechanisms mediating cell-matrix interactions. Furthermore, because natural tissue regeneration is characterized by the dynamic attachment/detachment of different cell populations, the design of advanced scaffolds for tissue engineering, based in the spatiotemporal tuning of cell-matrix anchorage is discussed.

Early implant healing: promotion of platelet activation and cytokine release by topographical, chemical and biomimetical titanium surface modifications in vitro

Platelet releasate has been shown to promote osteogenetic cell proliferation and differentiation. Topography and chemistry of biomaterials have high impact on platelet activation. More specifically, the bioactive cell adhesive peptide sequence Arg-Gly-Asp (RGD) triggers platelet activation mediated by the α(IIb) β(3) integrin receptor. Accordingly, topographical, chemical and biomimetical (immobilized RGD peptide) modifications of titanium (Ti) surfaces may enhance early platelet activation and bony healing of implants. Therefore, the aim of the study was to evaluate platelet activation with subsequent platelet-derived cytokine release by accordingly modified Ti surfaces. Pre-treated (PT; mean roughness [R(a)]=0.04 μm, contact angle [CA]=91°), acid-etched (A, R(a) =0.83 μm, CA=106°), large grit-sandblasted, acid-etched (SLA, R(a) =3.2 μm, CA=109°) as well as hydrophilically modified acid-etched (modA, R(a) =0.83 μm, CA=0) and modified large grit-sandblasted, acid-etched (modSLA, R(a) =3.2 μm; CA=0°) titanium surfaces were investigated. Additionally, RGD peptides were chemically immobilized on PT, A and SLA surfaces (PT-RGD [CA=18°], A-RGD [CA=0°], SLA-RGD [CA=0°]). The different Ti surfaces were incubated with platelet concentrate of three healthy volunteers at room temperature for 15 min and for 30 min. High thrombogenous collagen served as the control group. Out of the supernatant, platelet consumption was assessed via platelet count (PC). Cytokine release was quantified via the level of platelet-derived growth factor (PDGF) and vascular endothelial growth factor (VEGF). After 15 min, especially the rough SLA surface showed a strong decrease in PC and a strong increase in VEGF and PDGF levels. After 30 min, high platelet consumption as well as high levels of VEGF and PDGF were measured for unspecifically modified (modA) and especially for biomimetic, specifically modified (PT-RGD, A-RGD) surfaces, indicating a delayed effect of the surface modifications on platelet activation. Modifications of surface roughness modifications appear to influence early platelet activation and cytokine release after 15 min whereas surface chemistry modifications with increased hydrophilic properties and surface modifications via RGD peptide on plainer surfaces lead to a further, more specific promotion of platelet activation and degranulation after 30 min. The observed effect could be valuable for critical clinical situations like compromised bone sites.

Biofunctionalized poly(ethylene glycol)-block-poly(ε-caprolactone) nanofibers for tissue engineering

Electrospun fibers with contrasting cell adhesion properties provided non-woven substrates with enhanced in vitro acceptance and controllable cell interactions. Poly(ethylene glycol)-block-poly(epsilon-caprolactone) (PEG-b-PCL) block copolymers with varying segment lengths were synthesized in two steps and characterized by NMR and GPC. A cell adhesive peptide sequence, GRGDS, was covalently coupled to the PEG segment of the copolymer in an additional step. The suitability of polymers with molecular weights ranging from 10 to 30 kDa for electrospinning and the influences of molecular weight, solvent, and concentration on the resulting morphologies were investigated. Generally, electrospun fibers were obtained by electrospinning polymers with molecular weight larger than 25 kDa and concentrations of 10 wt%. Methanol/chloroform (25/75, v/v) mixtures proved to be good solvent systems for electrospinning the PEG-b-PCL and resulted in hydrophilic, non-woven fiber meshes (contact angle 30 degrees ). The mesh without cell adhesive GRGDS ligands showed no attachment of human dermal fibroblasts after 24 h cell culture demonstrating that the particular combination of the material and electrospinnig conditions yielded protein and cell repellent properties. The GRGDS immobilized mesh showed excellent cellular attachment with fibroblasts viable after 24 h with spread morphology. Electrospun nanofibers based on block copolymers have been produced which are capable of specifically targeting cell receptor binding and are a promising material for tissue engineering and controlling cell material interactions.

Nitric oxide‐releasing polyurethane–PEG copolymer containing the YIGSR peptide promotes endothelialization with decreased platelet adhesion

Thrombosis and intimal hyperplasia are the principal causes of small-diameter vascular graft failure. To improve the long-term patency of polyurethane vascular grafts, we have incorporated both poly(ethylene glycol) and a diazeniumdiolate nitric oxide (NO) donor into the backbone of polyurethane to improve thromboresistance. Additionally, we have incorporated the laminin-derived cell adhesive peptide sequence YIGSR to encourage endothelial cell adhesion and migration, while NO release encourages endothelial cell proliferation. NO production by polyurethane films under physiological conditions demonstrated biphasic release, in which an initial burst of 70% of the incorporated NO was released within 2 days, followed by sustained release over 2 months. Endothelial cell proliferation in the presence of the NO-releasing material was increased as compared to control polyurethane, and platelet adhesion to polyethylene glycol-containing polyurethane was decreased significantly with the addition of the NO donor.

Generation of cell adhesive substrates using peptide fluoralkyl surface modifiers

Previous studies reported on the delivery of vitamin E to the surface of a polycarbonate polyurethane (PCNU) to produce antioxidant surfaces, using a bioactive fluorinated surface modifer (BFSM). In the current report, a cell adhesive peptide sequence was coupled to the BFSM, and when blended into PCNU, generated a cell adhesive substrate. An NH 2-GK*GRGD-CONH 2 peptide sequence (referred to as RGD) with a dansyl label (*) on the lysine residue was coupled via the N-terminal to a BFSM precursor molecule. The resulting RGD BFSM was purified and the pmol peptide/mg BFSM value was assayed by amino acid quantification. The migration of the RGD BFSM in a PCNU blend was confirmed by X-ray photoelectron spectroscopy analysis. U937 macrophage-like cells and human monocytes were seeded onto the PCNU and blends of PCNU with non-bioactive fluorinated surface modifier or the RGD BFSM, in order to study the cell response. Both U937 cells and human monocytes adhered in greater numbers to the RGD BFSM substrate when compared to unmodified PCNU or the blend of PCNU with the non-bioactive fluorinated surface modifying macromolecule substrate. The study demonstrated a novel approach for the introduction of peptides onto the surface of polymers by modifying the surface from within the polymer as opposed to the use of cumbersome post-surface modification techniques. The generation of a peptide substrate points to the possibility of producing complex bioactive surfaces using various peptide BFSMs or pharmaceuticals simultaneously to manipulate cell functions.

Design and gene engineering synthesis of an extremely thermostable protein with biological activity.

A novel strategy for designing and synthesizing extremely thermostable biologically active proteins is proposed. The design concept is based on combining a rigid and extremely hydrophobic peptide unit with a biologically active peptide unit. The cell adhesive peptide sequence, Arg-Gly-Asp (RGD), as a functional peptide unit was incorporated into the elastin-based rigid polyhexapeptide, whose repeating unit is Ala-Pro-Gly-Val-Gly-Val (APGVGV). The designed fusion gene was expressed in E. coli, and the resulting protein, designated ER4, was purified with affinity chromatography. The ER4-coated cell culture plate showed sufficient cell adhesive activity through the RGD sequence on the surface of ER4. The thermostability of ER4 was demonstrated by estimating the remaining cell adhesive activity after autoclaving at 120 degrees C for 20 min, and it retained over 90% of cell adhesive activity compared with native ER4.

Design of a thermostable cell adhesion protein

The design principle of a thermostable functional protein has been proposed by demonstrating genetic engineering synthesis of a thermostable cell adhesion protein. The cell adhesive peptide sequence, Arg-Gly-Asp (RGD), was incorporated into the elastin-based polyhexapeptide, whose repeating unit is Ala-Pro-Gly-Val-Gly-Val (APGVGV). The resulting protein possesses cell adhesion activity approximately 80% of fibronectin. After autoclaving at 120 °C for 20 min, the protein retained over 90% of cell adhesion activity, while the activity of autoclaved fibronectin decreased to 50%.