Carrier Frequency Research Articles

Single shot point-diffraction interferometer by a plate beamsplitter

Abstract A single shot point-diffraction interferometer is proposed in this paper, in which one plate beamsplitter is assembled with one mirror and one pinhole array to duplicate an object beam and generate one object beam and one reference beam. One mirror is placed perpendicularly at the rear of the optical 4f system, while one thin plate beamsplitter is placed ahead of the mirror with an inclined angle. With the help of the half-transmission and half-reflection of the plate beamsplitter, one object beam is duplicated into to copies. Owning to the different angles of the plate beamsplitter and the mirror with respect to the optical axis, after Fourier transformed by the second Lens of the 4f system and reflected by the cube beamsplitter, the two copies are separated in the spectral domain. Then, one object beam and one reference beam are generated by the pinhole array placed at the spectral plane. The object and reference beams are Fourier transformed by the third Lens and interferes to generate an off-axis interferogram at the camera. By adjusting the inclined angle of the plate beamsplitter, the carrier frequency of the interferogram can be modulated easily. Therefore, this interferometer has a simple optical setup, easy optical implementation and outstanding measurement ability with high precision, measurement efficiency and stability. Several experimental results will be provided to demonstrate the effectiveness of the proposed system.

Genetic background of primary and familial HLH in Qatar: registry data and population study

BackgroundFamilial hemophagocytic lymphohistiocytosis (FHLH) is an inherited life-threatening disease. Five types are identified, with the addition of congenital immunodeficiency syndromes in which HLH is a typical manifestation. The literature on this disease is very scarce in the Middle East, with only a few scattered reports.MethodsWe report detailed demographic, clinical, and genomic data from 28 patients diagnosed with primary and familial HLH over the last decade in Qatar. An evaluation was performed of allele frequencies of deleterious variants from 12 primary and familial HLH causative genes on the Qatar Genome Programme (QGP) cohort of 14,669 Qatari individuals.ResultsThe genetic diagnosis was obtained in 15 patients, and four novel mutations in Perforin 1 (PRF1), UNC13D, LYST, and RAB27A genes were found. We identified 22,945 low/high/moderate/modifier impact variants significantly enriched in the QGP in those 12 genes. The variants rs1271079313 in PRF1 and rs753966933 in RAB27A found in our patient cohort were significantly more prevalent in the QGP compared to the Genome Aggregation Database (gnomAD) database, with a high carrier frequency in the Qatari population.ConclusionsWe established the first primary and familial HLH Registry in the Gulf Region and identified novel possibly pathogenic variants present at higher frequency in the Qatari population, which could be used for screening purposes. Raising awareness about primary and familial HLH and implementing screening activities in the Qatari highly inbred population could stem into more comprehensive premarital and prenatal evaluations and faster diagnosis.

Frequency Offset Estimation for UWB-OFDM System using Weight and Exhaustiveness based Monarch Butterfly Optimization Approach

The performance of an OFDM system has limitation because the carrier frequency offset (CFO) and sampling frequency offset (SFO) is not estimated correctly. Current methods propose the way of obtaining frequency estimation by using the evolutionary algorithm, but the evolution algorithm suffers from the premature convergence problem. In order to provide efficient frequency offset estimation, this paper proposed weight and exhaustiveness based monarch butterfly optimization approach. First, on the transmitter block, for modulating an input symbol, the Hybrid-Quadrature Phase-Shift Keying modulation scheme is used. Brunn’s IFFT is done at each transmitter for symbol mapping and then in each transmitter block cyclic prefix is inserted. After that, WE-MBO algorithm estimates the frequency offset. On receiver side, the inverse operation of the transmitter is performed. After comparison of proposed system with the existing system, the proposed system gave better performance.

Enhancing Data Rate and Energy Efficiency of NOMA Systems Using Reconfigurable Intelligent Surfaces for Millimeter-Wave Communications

In this article, we employ reconfigurable intelligent surface (RIS) to aid a non-orthogonal multiple access (NOMA) system utilizing millimeter-wave (mmWave) communications. Different to recent works on the RIS-supported NOMA systems where the certain carrier frequency was often normalized (fc=1 Hz), we analyze specific impacts of high carrier frequencies in the mmWave band (fc≥30 GHz) on the performance of the RIS-supported NOMA system. In particular, we derive the exact expressions of achievable data rate (ADR) and energy efficiency (EE) of the RIS-supported NOMA system using mmWave band (RIS-mmWave-NOMA system). We compare the ADR and EE of the RIS-mmWave-NOMA system with those of mmWave-NOMA system without RIS, where there are only source-user channels. Numerical illustrations clarify the benefits of utilizing RIS as well as the great impacts of high fc in mmWave band on the ADR and EE of the RIS-mmWave-NOMA system. More specifically, when fc increases from 50 to 100 GHz, the transmit power of source should be increased 8 dBm to achieve the same ADR. Meanwhile, the maximal EE with fc=100 GHz is greatly lower than the maximal EE with fc=50 GHz even though higher transmit power is used. In other words, when fc increases, higher transmit power can be used for the ADR aims but this method cannot be used for EE purposes. In these circumstances, utilizing a larger number of reflecting elements (REs) in the RIS is a good method. By using N≥200 REs, the ADR and EE of the RIS-mmWave-NOMA system are significantly higher than those of mmWave-NOMA system without RIS. Finally, we confirm the exactness of the derived formulas through Monte-Carlo simulations.

Carrier frequency and incidence of MUTYH-associated polyposis in an East Asian and Korean population by population database-based analysis

Carrier frequency and incidence of MUTYH-associated polyposis in an East Asian and Korean population by population database-based analysis

Non pilot data-aided carrier and sampling frequency offsets estimation in fast time-varying channel

This paper considers the non pilot data-aided estimation of the carrier frequency offset (CFO) and sample frequency offset (SFO) of orthogonal frequency division multiplexing (OFDM) signals in fast time-varying channel. The main obstacle is the time-variant channel response, which deteriorates the estimation validity. A practical approach to mitigate this impact is to reduce the time consumption of one-shot estimation. In this way, we propose a method to reduce the time consumption to within one OFDM symbol duration. The maximum likelihood (ML) estimator is derived based on the observations of frequency domain constellations output of two FFTs on one symbol; its closed-form approximation is then derived to reduce the calculation burden. Remarkably, our method does not require any training symbol or pilot tone embedded in the signal spectrum, therefore achieves the highest spectral efficiency. Theoretical analysis and simulation results are employed to assess the performance of proposed method in comparison with existing alternatives.

Performance Analysis of Filtered OFDM using MLE for Wireless Communication Networks

Introduction: OFDM has evolved as an effective modulation format for 4G mobile network technologies, Long-Term Evolution, and Worldwide Interoperability for Microwave Access. OFDM is the modulation technique adopted for communication standards such as DSL, wireless LAN, DVB, and DAB. However, because CP-OFDM has considerable out-of-band emission that may interfere with transmissions in adjacent bands and applies a single set of parameters to the whole band to fulfill a given service, it is unable to accommodate the diversity of services. The objective of the research is to develop a novel waveform with better adaptability than CP-OFDM that employs filters to increase spectrum containment. In this view, an FIR filter that uses the Blackman window function to lessen the OOBE is proposed in this manuscript. Filtered OFDM is sensitive to carrier frequency offset (CFO). CFO increases the Inter-Carrier Interference (ICI) in F-OFDM systems. However, research work that combines the CFO compensation technique with filtered OFDM has not been listed in the literature so far. Methods: In this paper, Maximum likelihood estimation is used to cancel the ICI caused by the CFO. The high PAPR of filtered OFDM is one of its drawbacks. The amplitude clipping method is used to reduce the PAPR. The distortion caused by amplitude clipping is prevented by filters used in the FOFDM system. Highlights: • A novel waveform addressing OOBE issues in OFDM is developed for 4G wireless communication networks. • An innovative solution using MLE is proposed to address the challenges faced by the filtered OFDM system due to the CFO. • Article addresses the high PAPR problem of filtered OFDM. method: This work presents a FIR filter that uses the Blackman window function to lessen the OOBE. Filtered OFDM is sensitive to carrier frequency offset (CFO). CFO increases the inter-carrier interference in F-OFDM systems. However, research work is not listed in the literature so far that combines CFO compensation technique with filtered OFDM. In this paper Maximum likelihood estimation is used to cancel the ICI caused by CFO. The high PAPR of filtered OFDM is one of its drawbacks. The amplitude clipping method is used to reduce the PAPR. The distortion caused due to amplitude clipping is prevented by filters used in the F-OFDM system Result: The performance of filtered OFDM with amplitude clipping is analyzed in terms of BER, PSD, and PAPR over the AWGN channel. Conclusion: Simulation results show that, when compared to the traditional OFDM system, such a combined method effectively suppresses PAPR while maintaining good BER (Bit Error Rate) and OOBE performance.

Exploring genetic variants in congenital monosaccharide-disaccharide metabolism: Carrier ratiosandphenotypic insights.

Adverse food reactions, often underestimated, encompass congenital monosaccharide-disaccharide metabolism disorders, yielding diverse outcomes such as abdominal pain, diarrhea, bleeding disorders, and even death. This study retrospectively scrutinized genetic variants linked to these disorders in a cohort subjected to whole-exome sequence analysis (WES), determining carrier frequencies and genotype-phenotype correlations. Data from 484 patients, were retrospectively analyzed using a gene panel (ALDOB, FBP1, GALE, GALK1, GALM, GALT, LCT, SLC2A2, SLC5A1, SI) for congenital monosaccharide-disaccharide metabolism disorders. WES was performed on patients using the xGen Exome Research Panel v2 kit, utilizing Next Generation Sequence Analysis (NGS). The study encompassed pathogenic, likely pathogenic, and variant of uncertain significance (VUS) variants. Among 484 patients (244 female, 240 male), 17.35% carried 99 variants (67 distinct) in the analyzed genes. Pathogenic/likely pathogenic allele frequency stood at 0.013, while VUS allele frequency was 0.088. Notably, 44% (37/84) of patients harboring mutations manifested at least one relevant phenotype. Carriage frequencies ranged from 1:25 (SI gene) to 1:968 (GALE gene), with the estimated disease frequency spanning from 1:2500 to 1:3748000. Our study underscores clinical manifestations in heterozygous carriers of recessive genetic disorders, addressing gaps in carrier frequencies and phenotypic effects for congenital monosaccharide-disaccharide metabolism disorders. This knowledge can improve these conditions'diagnosis and management, potentially preventing adverse food reactions and their associated complications.

Enhancing USVs navigation based on minimum error entropy of GPS vector tracking

In recent years, unmanned surface Vessels (USVs) have increasingly been used for river monitoring and hydrological surveys. USVs rely on global navigation satellite systems (GNSS) for navigation. However, signal blocking can cause the traditional GNSS vector tracking (VT) loop to increase the code phase and carrier frequency errors, leading to higher positioning errors that do not meet USVs’ requirements. To address this problem, we propose a VT method based on the minimum error entropy (MEE) in the signal tracking module. The MEE Kalman filter is adopted as the loop filter to mitigate code phase and carrier frequency errors, reduce non-Gaussian noise and random errors generated by signal blocking, and enhance the positioning accuracy and robustness of USV navigation. The measurement noise covariance of the loop filter was adjusted adaptively using the signal carrier-to-noise ratio. A field experiment was conducted using a commercial GNSS receiver as reference. The results demonstrate a 19.3% improvement in positioning accuracy compared with the traditional method in an open environment. Moreover, the proposed method maintains stable operation and achieves a 79.4% improvement in positioning accuracy during signal blocking. This novel algorithm offers a new concept for USV navigation systems to cope with signal blocking.

Power Amplifier Modeling Framework for Front-End-Aware Next-Generation Wireless Networks

Next-generation wireless systems require increased spectral and energy efficiency in terminals. This can only be achieved if the nonlinear characteristics of the radio front-end, primarily the power amplifier (PA), are known and considered while designing algorithms or optimizing radio links. PA datasheets contain limited information, and wideband PA measurements typically require advanced equipment and software. This paper proposes a measurement and signal processing framework that enables the acquisition of nonlinear PA characteristics using generic complex sample transmitters and receivers, e.g., software-defined radio (SDR). This paper also proposes a multistage signal calibration and synchronization procedure that allows obtaining nonlinear PA characteristics that are non-distorted by other phenomena. The correctness and usefulness of the proposed framework are demonstrated by measuring three PAs, each under varying supply voltage and carrier frequency. At the same time, the high variability of the obtained nonlinear characteristic justifies the need for PA measurements to obtain awareness of nonlinear characteristics.

A Modified SVPWM Strategy for Reducing PWM Voltage Noise and Balancing Neutral Point Potential

PWM (pulse width modulation) is the most widely applied current conversion technology, but the high-frequency harmonics it causes have a significant negative impact on inverter system performance. This paper focuses on the three-phase T-type three-level inverter as the research object and addresses existing PWM voltage noise and midpoint potential imbalance issues by proposing an improved random SVPWM strategy, named Neutral Point Potential Balance Random Space Vector PWM (NPB–RSVPWM). The NPB–RSVPWM strategy includes three main steps: (1) introducing a midpoint potential balancing control loop to adjust the synthesis timing of the effective vectors to generate pulse signals, optimizing midpoint potential balance; (2) employing a randomly varying carrier frequency in place of the carrier used in the SVPWM strategy to generate the driving signals for switching devices; and (3) controlling the inverter through the driving pulse signals. This strategy optimizes the synthesis sequence of traditional SVPWM strategy vectors and incorporates random frequency modulation techniques. The mathematical model analyzes PWM harmonic expressions corresponding to fixed switching frequencies, and a random frequency carrier is chosen to suppress these PWM harmonics. The effective vector’s equivalent circuit is analyzed, proposing a technique for optimized vector synthesis timing. The simulation and experimental results verify that the NPB–RSVPWM technique can disperse PWM harmonic energy, reduce voltage noise, and optimize midpoint potential balance. Under the NPB–RSVPWM strategy, the line voltage spectrum becomes uniform, the maximum harmonic content is greatly reduced, and the fluctuation in the DC side midpoint potential is significantly improved. Compared with the traditional SVPWM strategy and random PWM strategy, the NPB–RSVPWM strategy has a lower voltage noise, smaller total harmonic distortion, and a more stable midpoint potential. The effectiveness and feasibility of the NPB–RSVPWM strategy are verified by simulation and experimental results.

Rate dependent neural responses of interaural-time-difference cues in fine-structure and envelope.

Advancements in cochlear implants (CIs) have led to a significant increase in bilateral CI users, especially among children. Yet, most bilateral CI users do not fully achieve the intended binaural benefit due to potential limitations in signal processing and/or surgical implant positioning. One crucial auditory cue that normal hearing (NH) listeners can benefit from is the interaural time difference (ITD), i.e., the time difference between the arrival of a sound at two ears. The ITD sensitivity is thought to be heavily relying on the effective utilization of temporal fine structure (very rapid oscillations in sound). Unfortunately, most current CIs do not transmit such true fine structure. Nevertheless, bilateral CI users have demonstrated sensitivity to ITD cues delivered through envelope or interaural pulse time differences, i.e., the time gap between the pulses delivered to the two implants. However, their ITD sensitivity is significantly poorer compared to NH individuals, and it further degrades at higher CI stimulation rates, especially when the rate exceeds 300 pulse per second. The overall purpose of this research thread is to improve spatial hearing abilities in bilateral CI users. This study aims to develop electroencephalography (EEG) paradigms that can be used with clinical settings to assess and optimize the delivery of ITD cues, which are crucial for spatial hearing in everyday life. The research objective of this article was to determine the effect of CI stimulation pulse rate on the ITD sensitivity, and to characterize the rate-dependent degradation in ITD perception using EEG measures. To develop protocols for bilateral CI studies, EEG responses were obtained from NH listeners using sinusoidal-amplitude-modulated (SAM) tones and filtered clicks with changes in either fine structure ITD (ITDFS) or envelope ITD (ITDENV). Multiple EEG responses were analyzed, which included the subcortical auditory steady-state responses (ASSRs) and cortical auditory evoked potentials (CAEPs) elicited by stimuli onset, offset, and changes. Results indicated that acoustic change complex (ACC) responses elicited by ITDENV changes were significantly smaller or absent compared to those elicited by ITDFS changes. The ACC morphologies evoked by ITDFS changes were similar to onset and offset CAEPs, although the peak latencies were longest for ACC responses and shortest for offset CAEPs. The high-frequency stimuli clearly elicited subcortical ASSRs, but smaller than those evoked by lower carrier frequency SAM tones. The 40-Hz ASSRs decreased with increasing carrier frequencies. Filtered clicks elicited larger ASSRs compared to high-frequency SAM tones, with the order being 40 > 160 > 80> 320 Hz ASSR for both stimulus types. Wavelet analysis revealed a clear interaction between detectable transient CAEPs and 40-Hz ASSRs in the time-frequency domain for SAM tones with a low carrier frequency.

ELECTRODYNAMIC RESPONSE OF ANISOTROPIC MEDIUM OVER HYDROCARBONS TO THE INFLUENCE OF PROBING SIGNALS

A study was carried out of the electrodynamic response of an anisotropic medium over hydrocarbons under the influence of probing signals for pulsed and dual-frequency modes with a predominance of high-frequency signals. The characteristics of the geological profile above hydrocarbon deposits were studied using pulse signals depending on the carrier frequency and period of the radio pulse. For the dual-frequency signal mode, the dependences of the material and phase components of the surface impedance of the studied medium over oil and gas fields were modeled depending on the amplitude and frequency ratios. It has been established that an increase in the dielectric constant of the geological profile above the deposits leads to a decrease in resonance frequencies and the values of the absolute component of surface impedance Ż11. The revealed manifestations of anomalous effects expand information about the characteristics of the environment above deposits under the influence of pulsed electromagnetic waves and are of practical interest for exploratory geophysics. The results obtained can be used for electrical prospecting when creating equipment for detecting oil and gas fields.

Beampattern Synthesis and Optimization Method Based on Circular Frequency Diverse Array Engineering Model

The frequency diverse array (FDA) is capable of generating range-angle-dependent beampatterns by introducing a tiny frequency offset to the transmit carrier frequency of each array element. However, the beam-scanning potential of conventional linear FDA applications is limited, notably in their incapacity for 360° omnidirectional scanning. This paper introduces a method that leverages the geometric configuration of circular frequency diverse arrays (CFDAs) for synthesizing and optimizing beampatterns through a practical engineering approach. Initially, we compute the structural parameters and configurations of CFDA. Subsequently, the isophase plane is utilized to adjust the phase of each array element. Ultimately, the CFDA structure is used to optimize the non-uniform frequency offset, and the beampattern, which is capable of 360° omnidirectional scanning, is realized by low sidelobe optimization. Simulation results affirm that the CFDA antenna, as per the actual engineering model, possesses precise dot-shaped beampattern scanning abilities across both range and angle dimensions.

Anti-interrupted-sampling repeater jamming method based on frequency agility waveform and sparse recovery

Interrupted-sampling repeater jamming (ISRJ) is a type of intra-pulse coherent jamming that poses a significant threat to radar detection and tracking of targets. This paper proposes an ISRJ suppression method based on frequency agile waveform and sparse recovery, starting from the temporal discontinuity and modulation characteristics of ISRJ. This method is particularly suitable for scenarios with high jamming duty ratio (JDR) and high jammer sampling duty ratio (SDR). By dividing the transmitted waveform into sub-pulses with different carrier frequencies and applying a two-round block sparse algorithm, the method accurately recovers three parameters of ISRJ, achieving effective jamming identification, reconstruction, and cancellation. Additionally, a target detection technique based on robust sparse recovery is proposed, significantly improving the stability and accuracy of target detection. Comparative experimental results conducted in three scenarios confirm the effectiveness and superiority of this method under high JDR and SDR conditions.

A 0.73 mW low power 9.6 GHz LC voltage-controlled oscillator achieves constant KVCO and −189.2 FOM

This article introduces a novel approach of LC voltage-controlled oscillator (VCO) to overcome the challenges present in the Phase-locked loop (PLL) in high-frequency applications and proposes a 9.6 GHz VCO based on gm-boosted structure. By utilizing a transformer and gain variation calibration technique, the proposed VCO reduces the losses caused by MOSFET’s operation in triode region, thereby improving phase noise. And KVCO remains relatively constant, fluctuating up and down by approximately 5 MHz around 100 MHz/V, which is suitable to be used in phase-locked-loops (PLL). The oscillator is fabricated in 22 nm CMOS process occupying 0.25 mm × 0.55 mm area and consuming 0.73 mW from 0.5 V supply voltage. The measured phase noise achieves −114.3 dBc/Hz at 1 MHz offset with a carrier frequency of 4.75 GHz, and the figure of merit (FoM) is −189.2 dBc/Hz. The results clearly demonstrate that the proposed design could work under low power consumption and achieve constant KVCO, making it well suitable for high-frequency PLL applications.

Multiplex fluorescent amplification-refractory mutation system PCR method for the detection of 10 genetic defects in Holstein cattle and its comparison with the KASP genotyping assay.

The common deleterious genetic defects in Holstein cattle include haplotypes 1-6 (HH1-HH6), haplotypes for cholesterol deficiency (HCD), bovine leukocyte adhesion deficiency (BLAD), complex vertebral malformation (CVM) and brachyspina syndrome (BS). Recessive inheritance patterns of these genetic defects permit the carriers to function normally, but homozygous recessive genotypes cause embryo loss or neonatal death. Therefore, rapid detection of the carriers is essential to manage these genetic defects. This study was conducted to develop a single-tube multiplex fluorescent amplification-refractory mutation system (mf-ARMS) PCR method for efficient genotyping of these 10 genetic defects and to compare its efficiency with the kompetitive allele specific PCR (KASP) genotyping assay. The mf-ARMS PCR method introduced 10 sets of tri-primers optimized with additional mismatches in the 3' end of wild and mutant-specific primers, size differentiation between wild and mutant-specific primers, fluorescent labeling of universal primers, adjustment of annealing temperatures and optimization of primer concentrations. The genotyping of 484 Holstein cows resulted in 16.12% carriers with at least one genetic defect, while no homozygous recessive genotype was detected. This study found carrier frequencies ranging from 0.0% (HH6) to 3.72% (HH3) for individual defects. The mf-ARMS PCR method demonstrated improved detection, time and cost efficiency compared with the KASP method for these defects. Therefore, the application of mf-ARMS PCR for genotyping Holstein cattle is anticipated to decrease the frequency of lethal alleles and limit the transmission of these genetic defects.

Orthogonal-Frequency Simultaneous Wireless Power and Data Transfer for High-Power Wireless EV Charging

In a simultaneous wireless power and data transfer (SWPDT) system using common coils, achieving high-speed communication in high-power wireless charging systems is challenging due to power transfer interference on communication. Based on high-frequency data carrier-based SWPDT (HFDC-SWPDT) technology, this paper proposes an orthogonal-frequency simultaneous wireless power and data transfer (OF-SWPDT) method to minimize interference where the data carrier frequency is orthogonal to the power carrier frequency and its harmonics. In addition, a guard band is inserted between the spectra of power harmonics and data in order to further separate the power and data spectra. Thus, a high-power, high-speed SWPDT system is achieved. Finally, an 11 kW prototype with 64.125 kbps full-duplex communication is developed to validate the proposed method.

Detection of quadratic phase coupling by cross-bicoherence and spectral Granger causality in bifrequencies interactions

Quadratic Phase Coupling (QPC) serves as an essential statistical instrument for evaluating nonlinear synchronization within multivariate time series data, especially in signal processing and neuroscience fields. This study explores the precision of QPC detection using numerical estimates derived from cross-bicoherence and bivariate Granger causality within a straightforward, yet noisy, instantaneous multiplier model. It further assesses the impact of accidental statistically significant bifrequency interactions, introducing new metrics such as the ratio of bispectral quadratic phase coupling and the ratio of bivariate Granger causality quadratic phase coupling. Ratios nearing 1 signify a high degree of accuracy in detecting QPC. The coupling strength between interacting channels is identified as a key element that introduces nonlinearities, influencing the signal-to-noise ratio in the output channel. The model is tested across 59 experimental conditions of simulated recordings, with each condition evaluated against six coupling strength values, covering a wide range of carrier frequencies to examine a broad spectrum of scenarios. The findings demonstrate that the bispectral method outperforms bivariate Granger causality, particularly in identifying specific QPC under conditions of very weak couplings and in the presence of noise. The detection of specific QPC is crucial for neuroscience applications aimed at better understanding the temporal and spatial coordination between different brain regions.

Millimeter-wave over fiber integrated sensing and communication system using self-coherent OFDM

Orthogonal frequency-division multiplexing (OFDM) waveform is highly preferred as a dual-function candidate for integrated sensing and communication (ISAC) systems. However, the sensitivity to both carrier frequency offset (CFO) and phase noise greatly impedes its applications in millimeter-wave ISAC systems. Here, we propose and experimentally demonstrate a photonic millimeter-wave ISAC system employing the virtual-carrier-aided self-coherent OFDM technique, wherein a digitally-generated local oscillator is transmitted along with the OFDM signal. Then, a compact CFO-immune and phase noise-immune envelope detection method is implemented for down-converting millimeter-wave communication and radar echo signals. In experiments, a V-band ISAC system is successfully implemented with a simplified remote radio unit, using the remote photonic millimeter-wave heterodyning up-conversion for downlink and the envelope detection-assisted down-conversion for uplink (or radar echoes). In the converged transmission link with a 5-km fiber link and 2-m space link, the Kramers–Kronig (KK) receiver supports a communication data rate up to 16-Gbit/s by mitigating signal-signal beat interference (SSBI). More significantly, the SSBI leads to negligible effects on the sensing performance when classic matched filtering is adopted for target identification. Consequently, a 4.8-cm range resolution and a 4-mm range accuracy are obtained for the radar sensing function.