Carrier-based Dry Powder Inhaler Formulations Research Articles

Development of drug alone and carrier-based GLP-1 dry powder inhaler formulations

The study aimed to develop two types of dry powder inhaler (DPI) formulations containing glucagon-like peptide-1(7–36) amide (GLP-1): carrier-free (drug alone, no excipients) and carrier-based DPI formulations for pulmonary delivery of GLP-1. This is the first study focusing on the development of excipient free GLP-1 DPI formulations for inhaled therapy in Type 2 diabetes. The aerosolisation performance of both DPI formulations was studied using a next generation impactor and a DPI device (Handihaler®) at flow rate of 30 L min−1. Carriers employed were either a 10% w/w glycine-mannitol prepared by spray freeze drying or commercial mannitol. Spray freeze dried (SFD) carrier was spherical and porous whereas commercial mannitol carrier exhibited elongated particles (non-porous). GLP-1 powder without excipients for inhalation was prepared using spray drying and characterised for morphology including size, thermal behaviour, and moisture content. Spray dried (SD) GLP-1 powders showed indented/dimpled particles in the particle size range of 1–5 µm (also mass median aerodynamic diameter, MMAD: <5 µm) suitable for pulmonary delivery. Across formulations investigated, carrier-free DPI formulation showed the highest fine particle fraction (FPF: 90.73% ± 1.76%, mean ± standard deviation) and the smallest MMAD (1.96 µm ± 0.07 µm), however, low GLP-1 delivered dose (32.88% ± 7.00%, total GLP-1 deposition on throat and all impactor stages). GLP-1 delivered dose was improved by the addition of SFD 10% glycine-mannitol carrier to the DPI formulation (32.88% ± 7.00%–45.92% ± 5.84%). The results suggest that engineered carrier-based DPI formulations could be a feasible approach to enhance the delivery efficiency of GLP-1. The feasibility of systemic pulmonary delivery of SD GLP-1 for Type 2 diabetes therapy can be further investigated in animal models.

Powder flow analysis: A simple method to indicate the ideal amount of lactose fines in dry powder inhaler formulations

Many efforts have been made in the past to understand the function of lactose fines which are given as a ternary component to carrier-based dry powder inhaler formulations. It is undisputed that fines can significantly improve the performance of such formulations, but choosing the right amount of fines is a crucial point, because too high concentrations can have negative effects on the dispersion performance. The aim of this study was to indicate the optimal concentration of fines with a simple test method. For this purpose, mixtures with salbutamol sulfate and two different lactose carriers were prepared with a high shear mixer, measured with a FT4 powder rheometer and tested for fine particle delivery with two different inhaler devices. A correlation between the fluidization energy, measured with the aeration test set up, and the fine particle fractions (FPF) could be proven. This also applied for the aeration ratio, as well as the permeability of the powder samples. In addition, drug-free mixtures hardly differed in their rheological properties from mixtures containing the active pharmaceutical ingredient (API), which indicates that the method could be suitable for cost-saving screening trials. Furthermore, important aspects that explain the function of fines, such as the saturation of active sites, the formation of agglomerates and an increase in fluidization energy, could be shown in this study.

DEM analysis of the effect of electrostatic interaction on particle mixing for carrier-based dry powder inhaler formulations

Particle interactions play a significant role in controlling the performance of dry powder inhalers (DPIs), which mainly arise through van der Waals potentials, electrostatic interactions, and capillary forces. Our aim is to investigate the influence of electrostatic charge on the performance of DPIs as a basis for improving the formulation of the particle ingredients. The mixing process of carrier and active pharmaceutical ingredient (API) particles in a vibrating container is investigated using a discrete element method (DEM). The number of API particles attaching to the carrier particle (i.e., contact number) increases with increasing charge and decreases with increasing container size. The contact number decreases with increasing vibrational velocity amplitude and frequency. Moreover, a mechanism governed by the electrostatic force is proposed for the mixing process. This mechanism is different from that previously proposed for the mixing process governed by van der Waals forces, indicating that long-range and short-range adhesive forces can result in different mixing behaviours.

The influence of secondary processing on the structural relaxation dynamics of fluticasone propionate.

This study investigated the structural relaxation of micronized fluticasone propionate (FP) under different lagering conditions and its influence on aerodynamic particle size distribution (APSD) of binary and tertiary carrier-based dry powder inhaler (DPI) formulations. Micronized FP was lagered under low humidity (LH 25C, 33% RH [relative humidity]), high humidity (HH 25°C, 75% RH) for 30, 60, and 90days, respectively, and high temperature (HT 60°C, 44% RH) for 14days. Physicochemical, surface interfacial properties via cohesive-adhesive balance (CAB) measurements and amorphous disorder levels of the FP samples were characterized. Particle size, surface area, and rugosity suggested minimal morphological changes of the lagered FP samples, with the exception of the 90-day HH (HH90) sample. HH90 FP samples appeared to undergo surface reconstruction with a reduction in surface rugosity. LH and HH lagering reduced the levels of amorphous content over 90-day exposure, which influenced the CAB measurements with lactose monohydrate and salmeterol xinafoate (SX). CAB analysis suggested that LH and HH lagering led to different interfacial interactions with lactose monohydrate but an increasing adhesive affinity with SX. HT lagering led to no detectable levels of the amorphous disorder, resulting in an increase in the adhesive interaction with lactose monohydrate. APSD analysis suggested that the fine particle mass of FP and SX was affected by the lagering of the FP. In conclusion, environmental conditions during the lagering of FP may have a profound effect on physicochemical and interfacial properties as well as product performance of binary and tertiary carrier-based DPI formulations.

An investigation into the effect of fine lactose particles on the fluidization behaviour and aerosolization performance of carrier-based dry powder inhaler formulations.

The effect of milled and micronized lactose fines on the fluidization and in vitro aerosolization properties of dry powder inhaler (DPI) formulations was investigated, and the suitability of static and dynamic methods for characterizing general powder flow properties of these blends was assessed. Lactose carrier pre-blends were prepared by adding different lactose fines (Lactohale® (LH) 300, 230 and 210) with coarse carrier lactose (Lactohale100) at 2.5, 5, 10 and 20wt% concentrations. Powder flow properties of lactose pre-blends were characterized using the Freeman Technology FT4 and Schulze RST-XS ring shear tester. A strong correlation was found between the basic flow energy (BFENorm) measured using the Freeman FT4 Rheometer and the flowability number (ffc) measured on Schulze RST-XS. These data indicate that both static and dynamic methods are suitable for characterizing general powder flow properties of lactose carriers. Increasing concentration of fines corresponded with an increase in the normalized fluidization energy (FENorm). The inclusion of fine particles of lactose resulted in a significant (p < 0.05) increase in fine particle delivery of budesonide and correlated with FENorm. This trend was strongest for lactose containing up to 10wt% LH300. A similar trend was found for the milled lactose grades LH230 and LH210. However, the increase in FENorm upon addition of milled fines only corresponded to a very slight improvement in the performance. These data suggest that whilst the fluidization energy correlated with fine particle delivery, this relationship is specific to lactose grades of similar particle size.

Influence of crystal form of ipratropium bromide on micronisation and aerosolisation behaviour in dry powder inhaler formulations

This study aimed to investigate the relationship between the mechanical properties of anhydrous and monohydrate ipratropium bromide (IB) crystals, their processing behaviour upon air-jet micronisation and aerosolisation performance in dry powder inhaler (DPI) formulations. IB monohydrate and anhydrous crystals were produced from seed crystals and supercritical carbon dioxide crystallisation, respectively. Young's modulus of anhydrous and monohydrate IB crystals was determined using nanoindentation. For air-jet micronised crystals, the physicochemical and surface interfacial properties via the cohesive-adhesive balance (CAB) approach were investigated. These data were correlated to in-vitro aerosolisation performance of carrier-based DPI formulations containing either anhydrous or monohydrate IB. Particle size and Young's modulus of both crystals were similar and this was reflected in their similar processing upon micronisation. Particle size of micronised anhydrous and monohydrate crystals were similar. CAB measurements of the micronised particles of monohydrate or anhydrous forms of IB with respect to lactose were 0.70 (R² = 0.998) and 0.77 (R² = 0.999), respectively. These data suggested that both samples had similar adhesion to lactose, which correlated with their similar in-vitro aerosolisation performance in DPI formulations. Monohydrate and anhydrous crystals of IB exhibited similar mechanical properties and interfacial properties upon secondary processing. As a result, the performance of the DPI formulations were similar.

Influence of primary crystallisation conditions on the mechanical and interfacial properties of micronised budesonide for dry powder inhalation

Investigate the influence of primary crystallisation conditions on the mechanical properties and secondary processing behaviour of budesonide for dry powder inhaler (DPI) formulations. Young's modulus of two batches of budesonide crystals (samples A and B) produced using different anti-solvents was determined using nanoindentation. Physicochemical and surface interfacial properties via the cohesive–adhesive balance (CAB) approach to colloid probe atomic force microscopy (AFM) of air-jet micronised budesonide crystals were also investigated. These data were correlated to in vitro aerosolization performance of carrier-based DPI formulations containing either budesonide samples A or B and lactose monohydrate. Young's modulus of budesonide samples A and B crystals was 0.95 and 4.04GPa, respectively. Sample A crystals with low Young's modulus exhibited poorer micronisation efficiency than sample B. CAB analysis of micronised budesonide samples A and B, suggest that sample B budesonide had a greater adhesion to lactose than sample A. These data correlated with in vitro aerosolisation studies, which showed that the fine particle delivery of budesonide sample A was higher than that of sample B. In conclusion, crystallisation conditions may affect the mechanical properties of budesonide, and therefore secondary processing of the material and their interfacial properties and product performance in carrier based DPI formulations.

Investigation into the Influence of Primary Crystallization Conditions on the Mechanical Properties and Secondary Processing Behaviour of Fluticasone Propionate for Carrier Based Dry Powder Inhaler Formulations

To investigate the influence of primary crystallization conditions on the mechanical properties and secondary processing behaviour of fluticasone propionate (FP) for carrier based dry powder inhaler (DPI) formulations. Young's modulus of FP crystals produced using different anti-solvents was determined using nanoindentation. Physicochemical and surface interfacial properties via the cohesive-adhesive balance (CAB) approach to colloid probe atomic force microscopy (AFM) of air-jet micronised FP crystals were investigated. These data were correlated to in vitro aerosolization performance of binary and combination DPI formulations containing salmeterol xinafoate (SX). Young's modulus of FP crystals produced using different anti-solvents ranged from 0.6-12.4GPa. Crystals with low Young's modulus required multiple passes in the microniser to reduce the particle size to less than 5μm, whilst those with the highest Young's modulus required a single pass. CAB of micronized FP samples was similar with respect to lactose, however, their adhesive affinity to SX varied. Samples of FP with greatest adhesion to SX produced greater fine particle delivery of SX in combination DPI formulations. Crystallisation conditions may affect the mechanical properties of FP, and therefore secondary processing of the material and their interfacial properties and product performance in carrier based DPI formulations.

The Role of Fines in the Modification of the Fluidization and Dispersion Mechanism Within Dry Powder Inhaler Formulations

To investigate the role of in situ generated fine excipient particles on the fluidization and aerosolization properties of dry powder inhaler (DPI) formulations. Carrier based DPI formulations were prepared under low and high shear blending. Powder rheometery was utilized to measure bulk powder properties in a consolidated and aerated state. Powder fluidization and aerosolization characteristics were related to bulk powder properties using high speed imaging and inertial impaction measurements. High shear blending of formulations resulted in the in situ generation of excipient fines, which corresponded to an increase in aerosolization efficiency. The generation of fines were shown to increase the tensile strength and free volume of the carrier, which resulted in a characteristic change in the fluidization properties, as observed by high speed imaging. The increase in minimum fluidization velocity and aerodynamic drag forces required to aerate the powder may provide the source of energy for the increase in fine particle re-suspension. The in situ generation of excipient fines affect bulk powder properties of DPI formulations, which directly affects fluidization and aerosolization behaviour of DPI formulations. The study suggests an alternative mode of action by which fines increase DPI formulation performance.

The influence of relative humidity on particulate interactions in carrier-based dry powder inhaler formulations

An atomic force microscope (AFM) colloid probe technique has been used to investigate the effect of relative humidity (RH) on the adhesion properties of pharmaceutical powder surfaces. The adhesion between a model substrate, α-lactose monohydrate, and model particulate drugs, salbutamol sulphate and budesonide, was investigated between RHs of 15 and 75%. The surface topography of the model α-lactose monohydrate was produced by controlling the supersaturation conditions during crystal growth to produce sub-nanometre scale roughness. The adhesion interactions between lactose and drug probes of salbutamol sulphate and budesonide were shown to be significantly increased with each incremental rise in humidity. Capillary forces were significantly more dominant for the adhesion in the budesonide–lactose system up to 60% RH but were more dominant for salbutamol sulphate–lactose above 60% RH. These studies suggested that non-surface-specific capillary forces play a dominant role in the adhesion between drug and carrier, which may significantly reduce the deaggregation and dispersion properties of a dry powder formulation.