Capacity Of Membranes Research Articles

Ultra-high Prussian blue loading in SPEEK matrix fabricated by one-step electrostatic spraying as proton exchange membranes for fuel cell

Mixed matrix proton exchange membrane is promising for fuel cell application, but maximizing nanofiller loading to enhance performance is significant challenge. This study developed a one-step electrostatic spraying strategy to prepare ultra-high Prussian blue loading (up to 66.7 wt%) in sulfonated poly(ether ether ketone) matrix (PB@SPEEK). By coupling the electrostatic spraying and in situ solvent evaporation densification, SPEEK fills the voids between PB nanoparticles, forming a bicontinuous microstructure in the membrane. The ultra-high PB content of 66.7 wt% enable a fully utilization of its intrinsic properties, resulting in extremely low swelling ratio of 3.4% at 80°C, excellent flexibility of freely folding, and nearly 100% mass retention after 12-hour immersion in Fenton reagent at 60°C. In single-cell tests, the PB@SPEEK mixed matrix membrane shows stable internal resistance due to easily water hydration, therefore achieving excellent low-temperature peak power (1973.9 mW/cm2 at 40 °C and 2078.0 mW/cm2 at 60°C). The strategy developed in this study enables the one-step preparation of large-area, ultra-thin and ultra-high capacity of inorganic nanofiller mixed matrix proton exchange membranes for high-performance fuel cell.

Morphology and methanol permeability of sulfosuccinic acid cross‐linked polyvinyl alcohol and polyvinyl alcohol/Nafion nanofibrous membranes

AbstractCross‐linking of polyvinyl alcohol (PVA) and polyvinyl alcohol/Nafion (PVA/Nafion) electrospun nanofibers with sulfosuccinic acid (SSA) was investigated to assess their characterization and the effects of cross‐linking on the methanol permeability performance of the nanofibrous membranes. SSA was directly incorporated into the electrospinning polymer solution. The morphology, chemical functional groups, thermal stability, water stability and water swelling of the resulting nanofibers were examined. The effects of SSA concentration on ion exchange capacity (IEC) and methanol permeability of the nanofibrous membranes were discussed. Bead‐free and smooth nanofibers were produced for all SSA concentrations with a mean nanofiber diameter of 240–270 nm. It was shown that 15% SSA concentration was suitable for preserving the morphology of PVA nanofibers against water, while the morphology of PVA/Nafion nanofibers was preserved even without cross‐linking. The increase in SSA concentration led to increase in swelling in water. SSA cross‐linking was also shown to increase the thermal stability of the produced nanofibers. IEC increased by the increase in SSA concentration, while increase in SSA concentration led to a decrease in methanol permeability.

How Is Bone Regeneration Influenced by Polymer Membranes? Insight into the Histological and Radiological Point of View in the Literature.

The aim of this study was to analyze published works that investigate the in vivo bone regeneration capacity of polymeric membranes loaded with active substances and growth factors. This scoping review's purpose was to highlight the histological and radiological interpretation of the locally produced effects of the polymer membranes studied so far. For the selection of the articles, a search was made in the PubMed and ScienceDirect databases, according to the PRISMA algorithm, for research/clinical trial type studies. The search strategy was represented by the formula "((biodegradable scaffolds AND critical bone defect) OR (polymers AND mechanical properties) OR (3Dmaterials AND cytotoxicity) AND bone tissue regeneration)" for the PubMed database and "((biodegradable scaffolds AND polymers) OR (polymers AND critical bone defects) OR (biodegradable scaffolds AND mechanical properties) AND bone tissue regeneration)" for the ScienceDirect database. Ethical approval was not required. Eligibility criteria included eight clinical studies published between 2018 and 2023. Our analysis showed that polymer membranes that met most histopathological criteria also produced the most remarkable results observed radiologically. The top effective scaffolds were those containing active macromolecules released conditionally and staged. The PLGA and polycaprolactone scaffolds were found in this category; they granted a marked increase in bone density and improvement of osteoinduction. But, regardless of the membrane composition, all membranes implanted in created bone defects induced an inflammatory response in the first phase.

Electrical and Viscoelastic Parameters of Erythrocytes as a Part of Diagnostic Models for Differentiating Fatty Liver Disease of Mixed Genesis from Non-Alcoholic and Alcohol-Related Fatty Liver Disease

Aim:creation of diagnostic models including electrical, viscoelastic parameters of erythrocytes to distinguish fatty liver disease of mixed etiology (metabolic + alcoholic) from non-alcoholic and alcoholic fatty liver disease.Materials and methods.We examined 46 men with non-alcoholic fatty liver disease (NAFLD), 43 men with alcoholic fatty liver disease (AFLD), as well as 54 men with fatty liver disease (FLD) of mixed genesis (metabolic + alcohol-related); average age of the patients included in the study made 48.4 ± 9.6 years. The diagnosis was established on the basis of liver ultrasound findings and FLI liver steatosis index with a fibrosis grade of F1 or less (FibroScan®502, Echosens, France). The electrical and viscoelastic parameters of erythrocytes were investigated by the diagnostic technique of dielectrophoresis using an electrooptical cell detection system.Results.The most significant parameters for differentiating fatty liver disease of mixed genesis (metabolic + alcoholic) from NAFLD using the Volcano plot have turned out to be cell polarizability at a frequency of 106Hz (p= 6.49 ×10-5), erythrocyte cell membrane capacity (p= 0.00077), relative polarizability (p= 0.001), the levels of which were higher in patients with NAFLD. On the contrary, the index of red blood cells destruction at 105Hz was higher in FLD of the mixed genesis (p= 0.047) and the crossover frequency was shifted to the high frequency range more than in NAFLD (p= 0.0005). The discriminant analysis has additionally revealed the significance of the degree of erythrocyte deformation at 5 ×105Hz in distinguishing between mixed-genesis FLD and NAFLD. In differentiating FLD of mixed genesis from NAFLD, a diagnostic model incorporating the above red blood cells parameters has provided an AUC of 0.829 (confidential interval: 0.742–0.916), sensitivity of 80.9 %, and specificity of 83.3 %. Two indicators of red blood cells have been established that statistically significantly distinguish the mixed-genesis FLD from the AFLD (Volcano plot); these are the index of red blood cells destruction at a frequency of 5 ×105Hz, which was higher with AFLD (p= 0.0007), and the capacity of cell membranes, the value of which prevailed in mixed-genesis FLD (p= 0.011). When distinguishing the mixed-genesis FLD from the AFLD, the combined model with the inclusion of three parameters of red blood cells, namely the index of red blood cells destruction at a frequency of 5 ×105Hz, the capacity of erythrocyte membranes, and polarizability at a frequency of 106Hz, has shown the highest levels of diagnostic accuracy, namely AUC = 0.751 (confidential interval: 0.611–0.908) with a sensitivity of 79.5 %, specificity of 74.7 %.Conclusion.The electrical and viscoelastic parameters of erythrocytes studied using the diagnostic technique of dielectrophoresis should be considered as promising biomarkers for the diagnosis of diffuse liver disease.

Higher solubility and lower onset temperature of protein denaturation increase the osteoconductive capacity of collagen membranes: A preclinical invivo study.

Collagen membranes are extensively used for guided bone regeneration procedures, primarily for horizontal bone augmentation. More recently, it has been demonstrated that collagen membranes promote bone regeneration. Present study aimed at assessing if structural modifications of collagen membranes may enhance their osteoconductive capacity. Twenty-four adult Wistar rats were used. Bilateral calvaria defects with a diameter of 5 mm were prepared and covered with prototypes of collagen membranes (P1 or P2). The P1 membrane (positive control) presented a lower onset temperature of protein denaturation and a higher solubility than the P2 membrane (test). The contralateral defects were left uncovered (NC). After 1 and 4 weeks, the animals were euthanized. A microcomputed tomography analysis of the harvested samples was performed within and above the bony defect. Undecalcified ground sections were subjected to light microscopy and morphometric analysis. Bone formation was observed starting from the circumferential borders of the defects in all groups at 1-week of healing. The foci of ossification were observed at the periosteal and dura mater sites, with signs of collagen membrane mineralization. However, there was no statistically significant difference between the groups. At 4 weeks, remnants of the collagen fibers were embedded in the newly formed bone. In the P2 group, significantly more bone volume, more new bone, and marrow spaces compared to the NC group were observed. Furthermore, the P2 group showed more bone volume ectocranially then the P1 group. Bone formation subjacent to a P2 membrane was superior than subjacent to the P1 membrane and significantly better compared to the control. Modifications of the physico-chemical properties may enhance the osteoconductive competence of collagen membranes, supporting bone formation outside the bony defects.

Advanced hybrid membrane constructed with silicon carbide, graphene oxide and functionalized silicon carbide for vanadium permeability, proton conductivity to battery and fuel cell applications

The energy sector is currently exploring eco-friendly energy conversion and storage devices, as an alternative to traditional fossil fuel devices. A unique hybrid proton exchange membrane is developed for proton exchange membrane fuel cells (PEMFC) and vanadium redox flow battery (VRFB) application. Polymeric nanocomposite membranes are effective for the selective and controlled transportation of ions between the electrodes. This study utilizes various modifiers such as GO, SGO, SPES, and SiC, to modify the PES polymer matrix. Analysis of the functional groups confirmed the presence of modifiers and hydroxyl groups on the nanocomposite membrane. Additionally, the use of Field Emission Scanning Electron Microscopy (FESEM) validated the existence of honeycomb and sponge-like voids as well as the surface morphology on the membrane surface. The incorporation of modifiers into the nanocomposite membrane matrix serves as a reliable barrier for the transport of vanadium ions, leading to a significant reduction in vanadium ion permeability across the membrane. The mechanical properties and ion exchange capacity of nanocomposite membranes are enhanced, while the permeability of VO2+ decreases compared to that of the bare PES membrane. The enhancement of proton conductivity is further achieved with the utilization of modifiers in PES polymer. As compared to bare PES membrane, PES/SPES + SGO (5%) exhibits less than half the permeability for vanadium, and PES/SiC shows 44.03 % elongation means twice of bare PES membrane.

Comparative study of random and block SPEEK copolymers for high-temperature proton exchange membrane electrolysis

Traditionally, High-temperature proton Exchange Membrane Electrolysis (HT-PEME) has relied on costly and exceptionally hydrogen-permeable PFSA ionomers like Nafion®, Flemion®, and Aciplex®. Sulfonated Poly (ether ether ketone) (SPEEK) membranes have been developed as potential substitutes for the highly hydrogen permeable Nafion® membranes. The ion exchange capacity (IEC) of SPEEK membranes has been varied, ranging from 0.5 to 2.2 meq/g, to enhance their performance. Furthermore, the incorporation of ion-conducting units into these polymers is explored using both random and block copolymerization approaches. At 75 °C, SPEEK membranes exhibit significantly lower hydrogen diffusivity (35–50 barriers) compared to Nafion® and Flemion® membranes (∼202 barriers). Among SPEEK yttria-stabilized zirconia membranes (YSZM), those produced through random copolymerization exhibit marginally greater proton-to-hydrogen selectivity than YSZM derived from block SPEEK copolymers with a similar ion exchange capacity (IEC). This could be ascribed to the improved hydrogen-blocking capability resulting from an underdeveloped hydrophilic component. Among the SPEEK membranes tested, the random SPEEK membrane with an IEC of approximately 1.9 meq/g demonstrates superior performance (6.8 A/cm2) compared to a similarly thick (∼45 μm) Flemion® membrane (4.4 A/cm2) at 2.2 V. However, during an accelerated stress test involving 410 successive fluctuating flow densities of 2.8 and 0.04 A/cm2 imitating the alternating period's cycles of a water electrolyzer, the random SPEEK membrane exhibits a higher degradation rate (860 μV/h) compared to Flemion® and Nafion® (505 μV/h).

Caveolin-3 regulates slow oxidative myofiber formation in female mice

Abstract Objectives Caveolin-3 (Cav-3) plays a pivotal role in maintaining skeletal muscle mass and function. Mutations or deletions of Cav-3 can result in the development of various forms of myopathy, which affect the integrity and repair capacity of muscle fiber membranes. However, the potential effect of Cav-3 on myofiber type composition remains unclear. Methods To investigate the effect of Cav-3 on muscle strength and running capacity, we examined the grip force test and the low/high-speed running test. Oxidative and glycolytic myofiber-related genes, proteins, and skeletal muscle fiber composition were measured to determine the role of the Cav-3 in oxidative myofiber formation. Results We report the impact of Cav-3 on enhancing muscle endurance performance in female mice, and the discovery of a new physiological function to increase the proportion of slow-twitch oxidative muscle fiber by analyzing the gastrocnemius and soleus. Skeletal muscle-specific ablation of Cav-3 in female mice increased oxidative myofiber-related gene expression and type I oxidative myofiber composition, with resultant improvements in endurance performance. In male mice, the absence of Cav-3 in skeletal muscle reduced in the expression of glycolytic fiber-related genes and proteins. Conclusions This study identified Cav-3 as a regulator of slow-twitch oxidative muscle fiber formation acting on female mice, which may provide a potential target for improving muscle oxidative function.

The impact of PAC-loaded polymer membrane thickness on chloroform removal and comparison of solvent and thermal membrane regeneration methods.

Powdered activated carbon (PAC) has better adsorption performance than granular activated carbon (GAC) and is widely used in water purification. In most cases, PAC is dosed into water directly, then precipitated as sludge, and landfilled. In this study, PAC was mixed with a polymer and dissolved in dimethylformamide (DMF) solvent to form a PAC-loaded membrane, which was then tested for chloroform removal. The chloroform adsorption capacity of the PAC membrane increased with increasing membrane thickness because of higher carbon loading. However, regardless of membrane thickness, the flux of the PAC membranes was similar since flux resistance predominantly occurred at the top dense polymer surface. This dense surface can be removed by sandpaper polishing, where the adsorption capacity of the polished PAC membranes was 20% higher than the unpolished membranes because of more even distribution of feed water on the polished surface. Removal of the dense surface via polishing increased the flux by 97% to 130%, exceeding the flux of typical household carbon block filters. Using DMF to regenerate the membrane recovered 48% to 66% of the initial adsorption capacity. Thermal regeneration of the exhausted PAC membrane at 250°C was more effective than DMF regeneration (both in terms of cost and performance), with 83% to 94% PAC membrane regeneration efficiency over four regeneration recycles. After four thermal regeneration cycles, flux increased by 300% and the membrane became brittle because of thermal aging of the polymer, indicating that a total of 6h of regeneration time (equivalent to three cycles in this study) was the limit for effective PAC membrane performance. PRACTITIONER POINTS: Powdered activated carbon was immobilized on a membrane to remove chloroform from water. Thicker membranes increased adsorption capacity but did not impact flux. Flux and capacity increased using polishing to remove the dense polymer surface and more evenly distribute flow across the membrane. Thermal regeneration of the membrane at 250°C was effective for up to three cycles and outperformed solvent-based regeneration. PAC-loaded filters are relevant for applications such as household carbon block filtration.

Fabrication of PVDF membranes via γ-ray irradiation and investigation into their membrane formation mechanisms and water treatment properties

Polyvinylidene fluoride (PVDF) membrane is a cheap and commonly used separation material, but its inherent hydrophobicity results in significant membrane contamination, which limits its engineering application and further development. The hydrophilic PVDF-g/co-NVP membrane was prepared through low-dose γ-ray irradiation and using N-vinyl-2-pyrrolidinone (NVP) as a modifier in this study. The effects of γ-ray dose and incorporating NVP additive on the microstructure, hydrophilicity, anti-fouling capability, and mechanical capacity of membranes were discussed. Molecular dynamics (MD) simulation method was used to comprehensively investigate the impact of the NVP on the physicochemical characteristics of membrane structure. Under a specific NVP load, the water contact angle of the membrane decreases from 87.92° to 52.66°. The pure water permeance reaches 362.1 L/m2 h, and the porosity increases to 55.21 %±1.29 %, which indicates that γ-ray irradiation with NVP addition can effectively adjust the pore structure and hydrophilicity of the membrane. During anti-fouling test against bovine serum albumin (BSA), the modified membrane exhibits remarkable anti-fouling characteristics, including reduced BSA accumulation, enhanced flux recovery, lower irreversible contamination level, and extended cleaning cycle compared with the original pure PVDF membrane because of its higher hydrophilicity and positive zeta-potential value. This study elucidates the mechanism underlying γ-ray graft modification of PVDF membranes, thereby providing valuable insights into the development of efficient functional membrane materials.

Synthesis, Characterization, and Fabrication of Nickel Metal-Organic Framework-Incorporated Polymer Electrolyte Membranes for Fuel-Cell Applications.

Proton-conducting sulfonated polymer metal-organic framework (MOF)-based composite membranes were synthesized by anchoring the nickel MOF (Ni-MOF) to the aromatic sulfonated polymer backbone. In this work, we sulfonated two different polymers, poly(1,4-phenylene ether ether sulfone) (PEES) and poly ether ether ketone (PEEK), with a controllable sulfonation degree, and the synthesized Ni-MOF was incorporated into the sulfonated polymers to prepare a polymer electrolyte membrane. The effect of an MOF as a pendant moiety on the polymer backbone had a significant effect on properties such as water uptake, thermal, mechanical, and oxidative stabilities, swelling ratio, ion-exchange capacity (IEC), morphology, proton conductivity, and fuel-cell performance. The presence of an MOF structure enhanced the water retention capacity of the composite membranes. Adding Ni-MOF to the composite membrane improved the fuel-cell performance by increasing the OCV and power density. Among the synthesized electrolytes, the 3 wt % Ni-MOF-incorporated sPEEK membrane displayed a power density of 319 mW/cm2 with a cell voltage of 0.79 V, which was higher than the pure sulfonated polymer. Thus, the developed composite membranes are suitable for fuel-cell applications.

Carbon capturing composite membranes comprising Cu‐MOF and PIM‐1

AbstractCarbon capture from different CO2‐enriched sources demands the establishment of cleaner innovations to make strides in improving the existing worldwide environment. Nanoparticles of inorganic copper‐based metal–organic framework (Cu‐MOF) have been impregnated in varying loadings into an intrinsically microporous polymer (PIM‐1) to concoct mixed‐matrix membranes (MMMs) for carbon capture applications. The impacts of Cu‐MOF doping and temperatures of feed gas streams on morphology and carbon detainment capability of manufactured membranes were investigated. The carbon seizing capacity of different membranes was assessed by estimating permeabilities, selectivities, dissemination and dissolvability coefficients, facilitation proportions, and activation energies. Compared with the unfilled PIM‐1 membrane, impregnation of 30% Cu‐MOF into polymer significantly enhanced CO2 penetrability from 3740 to 6360 Barrer together with CO2/N2 and CO2/CH4 selectivity advancements from 27 to 34 and from 16 to 18, respectively. Performing gas penetration tests at elevated temperatures raised the CO2 penetrability of the membrane. The carbon seizing capability of MMMs lying over Robeson's bound signifies their potential in various cleansing operations.

Investigation of conjugate heat and mass transfer in a sleeve-type hollow fiber membrane for liquid desiccant dehumidification

In adiabatic conditions, the dehumidification capacity of hollow fibre membranes decreases as solution temperature rises. To address this limitation, this study proposed a novel approach based on sleeve-type hollow fibre membranes. The study focused on three distinct fluid streams and the sleeve-type hollow fibre membrane tube. A three-dimensional model of the dehumidifier was created, and the dehumidifier's heat transfer, mass transfer, and fluid flow characteristics were thoroughly analyzed and experimentally validated. The results showed that the average values of the Sherwood number and Nusselt number on the air side are significantly influenced by the Reynolds number. On the solution side of the sleeve-type hollow membrane, the average Nusselt number and Sherwood number are approximately 4.0 and 4.6, respectively. According to the research, 76 % of the resistance is accounted for by the mass transfer resistance on the membrane side. The study's conclusions provide insightful information for improving the design of sleeve-type hollow fibre membrane dehumidifiers.

Boosting Demulsification and Antifouling Capacity of Membranes via an Enhanced Piezoelectric Effect for Sustaining Emulsion Separation.

Traditional superwettable membranes for demulsification of oil/water emulsions could not maintain their separation performance for long because of low demulsification capacity and surface fouling during practical applications. A charging membrane could repel the contaminants for a while, the charge of which would gradually be neutralized during the separation progress. Here, a superhydrophilic piezoelectric membrane (SPM) with sustained demulsification and antifouling capacity is proposed for achieving prolonged emulsion separation, which is capable of converting inherent pulse hydraulic filtration pressure into pulse voltage. A pulse voltage up to -7.6 V is generated to intercept the oil by expediting the deformation and coalescence of emulsified oil droplets, realizing the demulsification. Furthermore, it repels negatively charged oil droplets, avoiding membrane fouling. Additionally, any organic foulants adhering to the membrane undergo degradation facilitated by the generated reactive oxygen species. The separation data demonstrate a 98.85% efficiency with a flux decline ratio below 14% during a 2 h separation duration and a nearly 100% flux recovery of SPM. This research opens new avenues in membrane separation, environmental remediation, etc.

The Regenerative Capacity of Tissue-Engineered Amniotic Membranes.

Scaffolds can be introduced as a source of tissue in reconstructive surgery and can help to improve wound healing. Amniotic membranes (AMs) as scaffolds for tissue engineering have emerged as promising biomaterials for surgical reconstruction due to their regenerative capacity, biocompatibility, gradual degradability, and availability. They also promote fetal-like scarless healing and provide a bioactive matrix that stimulates cell adhesion, migration, and proliferation. The aim of this study was to create a tissue-engineered AM-based implant for the repair of vesicovaginal fistula (VVF), a defect between the bladder and vagina caused by prolonged obstructed labor. Layers of AMs (with or without cross-linking) and electrospun poly-4-hydroxybutyrate (P4HB) (a synthetic, degradable polymer) scaffold were joined together by fibrin glue to produce a multilayer scaffold. Human vaginal fibroblasts were seeded on the different constructs and cultured for 28 days. Cell proliferation, cell morphology, collagen deposition, and metabolism measured by matrix metalloproteinase (MMP) activity were evaluated. Vaginal fibroblasts proliferated and were metabolically active on the different constructs, producing a distributed layer of collagen and proMMP-2. Cell proliferation and the amount of produced collagen were similar across different groups, indicating that the different AM-based constructs support vaginal fibroblast function. Cell morphology and collagen images showed slightly better alignment and organization on the un-cross-linked constructs compared to the cross-linked constructs. It was concluded that the regenerative capacity of AM does not seem to be affected by mechanical reinforcement with cross-linking or the addition of P4HB and fibrin glue. An AM-based implant for surgical repair of internal organs requiring load-bearing functionality can be directly translated to other types of surgical reconstruction of internal organs.

Effects of Halloysite Nanotube (HNT) on the Cd<sup>2+</sup> Adsorption Capacity of Cellulose Acetate (CA) Thin Film Membranes

This paper aims to investigate the effects of adding and increasing the concentration of halloysite nanotube (HNT) to a cellulose acetate (CA) membrane which is produced through non-solvent-induced phase separation via hand casting. Different characterization tests are performed on the nanocomposite samples: Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), Fourier Transform Infrared Spectroscopy (FTIR), and Atomic Absorption Spectroscopy (AAS). The addition of the filler itself increases the presence of peaks and valleys on the surface of the nanocomposite membrane. The 5% HNT nanocomposite membrane has the largest peaks and valleys-both in size and number. Using the following contact times: 2, 4, and 6 hours, the adsorption capacity of the CA-HNT membranes is obtained with the aid of AAS results. The 5% HNT sample leads to a nanocomposite membrane with a higher adsorption capacity relative to that of a pure CA membrane.

Development and Performance Evaluation of Low-Cost Cellophane Paper-Based Biosensors for Polyphenol Detection in Teas: A Cost-Effective Alternative to Teflon® Membranes Biosensors

This study introduces biosensors developed using cellophane paper with immobilized polyphenol oxidase (PPO) from dwarf banana and eggplant peels, integrated with glutaraldehyde and a Clark electrode. These biosensors, optimized for enzyme concentration at 75 units for dwarf banana peel and 100 units for eggplant peel, demonstrated high sensitivity to catechol, paracetamol, pyrogallol, and hydroquinone, similar to traditional Teflon® Clark electrodes. Despite the lower measurement capacity of cellophane membranes (20-30) compared to Teflon's (300-400), the cost-effectiveness and accessibility of cellophane offer a strategic advantage. These biosensors effectively quantified polyphenols in teas, with results closely matching those from the standard Folin-Dennis method and Teflon® electrodes, maintaining a 95% confidence level and an error margin of less than 1%. Hence, the cellophane paper-based biosensors present a cost-effective, efficient alternative for polyphenol detection in teas, promising broader application due to their affordability and performance.

Synthesis of metal-organic framework hybrid nanocomposites based on MOFs@C3N4 with high selective separation ability for luteolin

Complex substrates found in certain extracts-particularly those containing high phenolic compounds with significant medicinal value-pose considerable challenges to developing molecularly imprinted membranes (MIMs) with specific recognition abilities. In this study, UiO-66-NH2, a metal–organic structure (MOF), was chosen as an optimizer to enhance the basic support material C3N4. A composite imprinted membrane based on MOFs was then prepared for the targeted adsorption of luteolin (LTL). This not only increases the surface area and pore capacity of the composite membranes, but also ensures unprecedented control over the membranes structure and good stability. To maximize the proportion of imprinted sites, we utilize an advanced boron affinity sol–gel imprinting technique that capitalizes on the exceptional response of the bifunctional monomer. By finely manipulating the imprinting process, controlled distribution of imprinted sites was achieved. Furthermore, the incorporation of Ag nanoparticles into the composite matrix of MIMs enhances selectivity and efficiency due to their plasmonic properties and high affinity for phenolic compounds, providing increased adsorption surface area and additional binding sites. The results showed satisfactory rebinding ability (56.25 mg g−1) and superselective (βAG/LTL = 4.43 and βCT/LTL = 8.49). It was worth noting that incorporating Ag nanoparticles into composite MIMs for the selective adsorption of LTL demonstrates significant potential. This includes enhanced selectivity, efficiency, and hydrophilicity of the membrane surface. Thus, enhanced hydrophilicity can establish stronger non-covalent interactions, namely hydrogen bonding and van der waals forces, with the target molecules, thereby significantly improving the adsorption capacity of the MIMs. The feasibility of this method was demonstrated via in-situ infrared analysis of the chemical structure changes before and after adsorption.

Biomimetic Collagen Membranes as Drug Carriers of Geranylgeraniol to Counteract the Effect of Zoledronate.

To counteract the effect of zoledronate and decrease the risk of osteonecrosis of the jaw (BRONJ) development in patients undergoing guided bone regeneration surgery, the use of geranylgeraniol (GGOH) has been proposed. Collagen membranes may act as biomimetical drug carriers. The objective of this study was to determine the capacity of collagen-based membranes doped with GGOH to revert the negative impact of zoledronate on the growth and differentiation of human osteoblasts. MG-63 cells were cultured on collagen membranes. Two groups were established: (1) undoped membranes and (2) membranes doped with geranylgeraniol. Osteoblasts were cultured with or without zoledronate (50 μM). Cell proliferation was evaluated at 48 h using the MTT colorimetric method. Differentiation was tested by staining mineralization nodules with alizarin red and by gene expression analysis of bone morphogenetic proteins 2 and 7, alkaline phosphatase (ALP), bone morphogenetic proteins 2 and 7 (BMP-2 and BMP-7), type I collagen (Col-I), osterix (OSX), osteocalcin (OSC), osteoprotegerin (OPG), receptor for RANK (RANKL), runt-related transcription factor 2 (Runx-2), TGF-β1 and TGF-β receptors (TGF-βR1, TGF-βR2, and TGF-βR3), and vascular endothelial growth factor (VEGF) with real-time PCR. One-way ANOVA or Kruskal-Wallis and post hoc Bonferroni tests were applied (p < 0.05). Scanning electron microscopy (SEM) observations were also performed. Treatment of osteoblasts with 50 μM zoledronate produced a significant decrease in cell proliferation, mineralization capacity, and gene expression of several differentiation markers if compared to the control (p < 0.001). When osteoblasts were treated with zoledronate and cultured on GGOH-doped membranes, these variables were, in general, similar to the control group (p > 0.05). GGOH applied on collagen membranes is able to reverse the negative impact of zoledronate on the proliferation, differentiation, and gene expression of different osteoblasts' markers.

Spatiotemporally sequential delivery of biomimetic liposomes potentiates glioma chemotherapy

As one of the most challenging cancers, glioma still lacks efficient therapeutic treatment in clinics. The dilemmas of nanodrug-based therapies for glioma are due not only the limited permeability of the blood–brain barrier (BBB) but also the deficiency of targeting tumor lesions. Thus, spatiotemporally sequential delivery of therapeutics from BBB-crossing to glioma accumulation is considered a strategy to obtain better outcomes. Here, we developed a biomimetic chemotherapy nanodrug composed of the hybrid membrane envelope of U87 cell membranes and RAW264.7 cell membranes, and the core of paclitaxel (PTX)-loaded liposome (PTX@C-MMCL). In the research, PTX@C-MMCL showed superior ability to cross the BBB via RAW264.7 cell membranes and accurate targeting to the brain tumor lesions relying on the homotypic targeting capacity of U87 cell membranes. Furthermore, PTX@C-MMCL can maintain a prolonged circulation in vivo. Importantly, PTX@C-MMCL effectively inhibited the development of glioma. Conclusively, our biomimetic nanodrug holds great potential for brain tumor targeting therapy.