Cadaveric Tibiae Research Articles

Biomechanical Comparison of Spacer Pin Fixation to Two Established Methods of Tibial Tuberosity Transposition Stabilization in Dogs.

The aim of this cadaveric study was to compare the biomechanical outcomes of three methods of stabilization for tibial tuberosity transposition to treat medial patellar luxation: a complete osteotomy with a two-pin and tension band wire (TBW) fixation (TBW group), a partial osteotomy with a two-pin fixation (2 Pin group), and a partial osteotomy with a spacer pin fixation (Spacer Pin group). Thirty medium to large-sized canine cadaveric tibiae were dissected and randomly assigned to one of three groups: TBW, 2 Pin, and Spacer Pin groups. The patellar ligaments were loaded in tension until ultimate failure. Ultimate failure force and mode of failure were documented, stiffness was calculated, and the results were compared statistically between the three treatment groups. There were not any significant differences in ultimate failure force or stiffness between groups. All groups predominantly failed by patellar ligament failure, with distal tibial crest fracture/displacement being the second-most common mode in the 2 Pin and Spacer Pin groups. The mechanical properties of the spacer pin stabilization were not different from the TBW and 2 Pin groups. The spacer pin technique could be an alternative way to stabilize tibial tuberosity following tibial tuberosity transposition with a partial osteotomy based on this cadaveric load-to-failure model.

Effects of the Direction of Two Kirschner Wires on Combined Tibial Plateau Leveling Osteotomy and Tibial Tuberosity Transposition in Miniature Breed Dogs: An Ex Vivo Study.

This study evaluates the impact of Kirschner wire (K-wire) insertion direction on the biomechanical properties of combined tibial plateau leveling osteotomy (TPLO) and tibial tuberosity transposition (TTT) procedures in small-breed dogs with cranial cruciate ligament rupture and medial patella luxation. Twenty-one cadaveric tibiae were divided into two groups; the specimens were divided into two groups; one underwent TPLO-TTT with a proximal pin placement (Group TTP), and the other received TPLO-TTT with a distal pin placement (Group TTD). For both pin placements, two additional subgroups were formed: one with a 0.56 mm tension band (Groups TTP0.56 and TTD0.56) and the other with a 0.76 mm tension band (Groups TTP0.76 and TTD0.76). The tensile force was applied, and failure load and mode were recorded. The distal pin direction in Group TTD0.56 exhibited a significantly higher mean failure load (380.1 N) compared to the proximal pin direction in Group TTP0.56 (302.2 N, p = 0.028). No significant differences were observed among the other groups. This study concludes that distal pin placement can provide similar or improved mechanical stability in cases with limited space for proximal pin placement during combined TPLO and TTT procedures.

Recommendation of minimal distal tibial length for long axis coordinate system definitions

Accurate anatomical coordinate systems for the foot and ankle are critical for interpreting their complex biomechanics. The tibial superior-inferior axis is crucial for analyzing joint kinematics, influencing bone motion analysis during gait using CT imaging and biplane fluoroscopy. However, the lack of consensus on how to define the tibial axis has led to variability in research, hindering generalizability. Even as advanced imaging techniques evolve, including biplane fluoroscopy and weightbearing CT, there exist limitations to imaging the entire foot together with the full length of the tibia. These limitations highlight the need to refine axis definitions. This study investigated various superior-inferior axes using multiple distal tibia lengths to determine the minimal field of view for representing the full tibia long-axis. Twenty human cadaver tibias were imaged and segmented to generate 3D bone models. Axes were calculated based on coordinate definitions that required user manual input, and a gold standard mean superior-inferior axis was calculated based on the population’s principal component analysis axis. Four manually calculated superior-inferior tibial axes groups were established based on landmarks and geometric fittings. Statistical analysis revealed that geometrically fitting a cylinder 1.5 times the mediolateral tibial width, starting 5 cm above the tibial plafond, yielded the smallest angular deviation from the gold standard. From these findings, we recommend a minimum field of view that includes 1.5 times the mediolateral tibial width, starting 5 cm above the tibial plafond for tibial long-axis definitions. Implementing these findings will help improve foot and ankle research generalizability and impact clinical decisions.

Evaluation of the Stability of Internal Fixation Constructs in a Low Distal Tibia Extra-articular Cadaveric Fracture Model: A Comparative Biomechanical Study.

Introduction Despite the recent advances in implant design, the choice of an internal fixation modality for extra-articular distal tibia fractures remains controversial, and there is sparse literature comparing the stability of intramedullary nails and locked plates for such fractures. Hence, we conducted a biomechanical study on an AO type 43A3 tibia fracturecadaveric model stabilized by four different constructs, viz., intramedullary (IM) interlocking nail, anteromedial plate, anterolateral plate, and posterior plate.An AO type 43A3 fracture is defined as an extra-articular fracture of the distal tibia with metaphyseal comminution. Methods A biomechanical comparative study on formalin-preserved human cadaveric tibiae was undertaken; a total of four groups were tested, with eight bones in each group. Out of the 32 cadaveric tibiae, 19 bones belonged to male cadavers, and 13 bones belonged to female cadavers. All bones were dissected from age-appropriate cadavers and fixed with an implant, followed by the creation of a 1 cm osteotomy to simulate an AO type 43A3 fracture. All fixation constructs were subjected to three-point bending tests in the anteroposterior (AP) and mediolateral (ML) planes. Three parameters, viz., bending stiffness, peak fracture gap angle, and neutral zone, were evaluated on the load-displacement curves. Afixation construct was deemed biomechanically stable if it had a highbending stiffness, a low neutral zone (inherent toggle in the construct by its weight), and a low peak fracture gap angle. Results Out of the four implants tested, locked IM nails exhibited the maximum biomechanical stability in terms of higher bending stiffness, smaller peak fracture gap angle, and smaller neutral zones. The IM nail exhibited the highest bending stiffness in the AP plane, and the anterolateral plate had the lowest bending stiffness, and the difference was statistically significant (p= 0.032).In the AP plane, the anterolateral plate exhibited a bending stiffness of 1.51 ± 0.69 Nm/degree, whereas the intramedullary nail exhibited a bending stiffness of 2.34 ± 0.81 Nm/degree, and the posterior locked plate had a bending stiffness of 1.57 ± 0.44 Nm/degree. In the ML plane, the anterolateral plate exhibited the highest neutral zone as compared to the intramedullary nail, which had the lowest neutral zone, and the difference was statistically significant (p = 0.019). The intramedullary nail exhibited the lowest neutral zone of 0.46 ± 0.31 degrees, whereas the posterior locked plate exhibited a neutral zone of 0.78 ± 0.43 degrees in the ML plane. The anterolateral plate exhibited a neutral zone of 1.43 ± 1.00 (expressed as mean ± SD) degrees in the mediolateral plane. Conclusion Our biomechanical study supports the recommendations of using a locked intramedullary nail for AO type 43A3 fractures. We concluded that the anterolateral plate construct exhibited the least biomechanical stability, in terms of lower AP bending stiffness and higher neutral zone. If the surgeon must choose a locked plating technique for any reason, the anterolateral locking plate should be avoided. If plating is at all required, we can recommend both anteromedial and posterior locked plating as biomechanically sound options.

Quantifying the immediate post-implantation strain field of cadaveric tibiae implanted with cementless tibial trays: A time-elapsed micro-CT and digital volume correlation analysis during stair descent

Primary stability, the mechanical fixation between implant and bone prior to osseointegration, is crucial for the long-term success of cementless tibial trays. However, little is known about the mechanical interplay between the implant and bone internally, as experimental studies quantifying internal strain are limited. This study employed digital volume correlation (DVC) to quantify the immediate post-implantation strain field of five cadaveric tibiae implanted with a commercially available cementless titanium tibial tray (Attune, DePuy Synthes). The tibiae were subjected to a five-step loading sequence (0–2.5 bodyweight, BW) replicating stair descent, with concomitant time-elapsed micro-CT imaging. With progressive loads, increased compression of trabecular bone was quantified, with the highest strains directly under the posterior region of the tibial tray implant, dissipating with increasing distance from the bone-implant interface. After load removal of the last load step (2.5BW), residual strains were observed in all of the five tibiae, with residual strains confined within 3.14 mm from the bone-implant interface. The residual strain is reflective of the observed initial migration of cementless tibial trays reported in clinical studies. The presence of strains above the yield strain of bone accepted in literature suggests that inelastic properties should be included within finite element models of the initial mechanical environment. This study provides a means to experimentally quantify the internal strain distribution of human tibia with cementless trays, increasing the understanding of the mechanical interaction between bone and implant.

On the importance of accurate elasto-plastic material properties in simulating plate osteosynthesis failure.

Background: Plate osteosynthesis is a widely used technique for bone fracture fixation; however, complications such as plate bending remain a significant clinical concern. A better understanding of the failure mechanisms behind plate osteosynthesis is crucial for improving treatment outcomes. This study aimed to develop finite element (FE) models to predict plate bending failure and validate these against in vitro experiments using literature-based and experimentally determined implant material properties. Methods: Plate fixations of seven cadaveric tibia shaft fractures were tested to failure in a biomechanical setup with various implant configurations. FE models of the bone-implant constructs were developed from computed tomography (CT) scans. Elasto-plastic implant material properties were assigned using either literature data or the experimentally derived data. The predictive capability of these two FE modelling approaches was assessed based on the experimental ground truth. Results: The FE simulations provided quantitatively correct prediction of the in vitro cadaveric experiments in terms of construct stiffness [concordance correlation coefficient (CCC) = 0.97, standard error of estimate (SEE) = 23.66, relative standard error (RSE) = 10.3%], yield load (CCC = 0.97, SEE = 41.21N, RSE = 7.7%), and maximum force (CCC = 0.96, SEE = 35.04, RSE = 9.3%), when including the experimentally determined material properties. Literature-based properties led to inferior accuracies for both stiffness (CCC = 0.92, SEE = 27.62, RSE = 19.6%), yield load (CCC = 0.83, SEE = 46.53N, RSE = 21.4%), and maximum force (CCC = 0.86, SEE = 57.71, RSE = 14.4%). Conclusion: The validated FE model allows for accurate prediction of plate osteosynthesis construct behaviour beyond the elastic regime but only when using experimentally determined implant material properties. Literature-based material properties led to inferior predictability. These validated models have the potential to be utilized for assessing the loads leading to plastic deformation in vivo, as well as aiding in preoperative planning and postoperative rehabilitation protocols.

Effect of screw insertion angle and speed on the incidence of transcortical fracture development in a canine tibial diaphyseal model.

To assess the incidence of transcortical fracture (TCF) development based on screw insertion angle and screw insertion speed. Cadaveric experimental study. Sixty-six canine tibiae. Sixty-six cadaveric tibiae were randomly assigned to one of six groups that varied based on screw insertion angle relative to the pilot hole (0, 5, or 10°) and screw insertion speed (650 or 1350 revolutions per minute [rpm]). Each tibia was mounted in a custom jig. Locking self-tapping screws (3.5 mm) were inserted at varying speeds and insertion angles, based on group assignment. Orthogonal radiographs were evaluated for TCFs. Fisher's exact tests with a Bonferroni correction were performed to evaluate differences in the frequency of TCF between groups. In Group A (0°/650 rpm: control), a 0% TCF rate was observed (n = 0/80). Group B (5°/650 rpm) had a 3.75% TCF rate (n = 3/80). Group C (10°/650 rpm) had a 12.5% TCF rate (n = 10/80). Group D (10°/hand insertion) had a 3.75% TCF rate (n = 3/80). Group E (10°/1350 rpm) had a 17.5% TCF rate (n = 14/80). Group F (0°/1350 rpm) had a 0% TCF rate (n = 0/80). Groups C and E had the highest TCF rates with a difference in TCF rates observed between the control group and Group C (p = .001) and between the control group and Group E (p < .001). Increased screw insertion angle and insertion speed appear to be predisposing factors for TCF development in cadaveric bone. Ensuring screw insertion is coaxial with the pilot hole and using slower screw insertion speeds may help reduce the risk of TCF development.

Mechanical properties of a bioabsorbable magnesium interference screw for anterior cruciate ligament reconstruction in various testing bone materials

Tears of the anterior cruciate ligament (ACL) negatively impact the stability and kinematics of the knee. Interference screws (ISs) are used for graft fixation in ACL reconstruction and provide sufficient fixation strength to withstand the patients' activities during the graft-to-bone integration process. Magnesium is a novel material used to manufacture IS given its strength and bioabsorbability. In previous studies, the selected magnesium IS design showed a better fixation performance in comparison to the conventional IS design due to its shape design and surface condition. In this study, bioabsorbable magnesium ISs were tested for their insertion (insertion torque and a number of turns to implement the IS) and fixation performance (pull-out and dynamic test). To obtain a reliable initial assessment of IS performance, ISs were implanted in 15 per cubic foot (PCF) Sawbones polyurethane foam blocks, Sawbones biomechanical tibia models with 17 PCF foam cores, and human cadaveric tibiae. Porcine tendons were used in the foam block pull-out test, and nylon ropes were used in all other test setups to prevent influences of the ligament graft material itself. In the pull-out test, the graft was subjected to tensile stress at a rate of 6 mm/min. For the dynamic test, 1000 cycles between 0 and 200 N were performed, followed by a final pull-out test. After each test, the tunnel widening pattern was observed by measuring the aspect ratio of the tunnel at the insertion site. The insertion torque lies within the normal insertion torque of the ISs as well as the average ligament tension before the insertion. In the foam block setup, the nylon rope showed a higher pull-out force than the porcine tendon. The comparison of each setup using nylon rope for both pull-out and pull-out after the dynamic test showed no significant difference between the foam block and cadaver setup. However, all tibia model setup shows unexpectedly high pull-out force due to the influence of its cortical layer. There were no statistically significant differences in tunnel widening between foam block-porcine tendon and foam block-nylon rope constructs. The pull-out resistance of magnesium ISs falls within the typical ACL tension range during daily activities. Even though the test results of the magnesium ISs are different in each bone material, the magnesium IS shows adequate fixation ability and workability during insertion without material failure.

Influence of Kirschner-Wire Insertion Angle on Construct Biomechanics following Tibial Tuberosity Osteotomy Fixation in Dogs.

The aim of this study was to evaluate the effect of Kirschner wire insertion angle on the biomechanical characteristics following tibial tuberosity osteotomy fixation in dogs. Twelve pairs of cadaveric tibia were harvested and randomly assigned to two treatment groups. Kirschner wires were placed either transversely (0 degrees) or placed caudodistally (30 degrees) with respect to the tibial tuberosity osteotomy. Each limb acted as its own respective control. Radiographic analysis allowed for the calculation of Kirschner wire insertion angle variance. Constructs were tested to monotonic failure while evaluating yield, peak, and failure forces, construct stiffness, and failure mode. Kirschner wire insertion angles were 1.1 ± 2.2 degrees and 30.5 ± 2.3 degrees, respectively, for 0-degree and 30-degree groups (p <0.0001). Yield (p = 0.0095), peak (p <0.024) and failure loads (p <0.030) were all significantly greater for Kirschner wires inserted at an angle of 0 degrees compared with 30 degrees. Construct stiffness did not differ regardless of insertion angle (p = 0.068). Failure mode did not differ (p = 0.87) with tibial tuberosity avulsion and Kirschner wire pull-out seen in the majority of constructs (67%). Kirschner wires placed transversely (0 degrees) for tibial tuberosity osteotomy fixation were biomechanically superior, increasing yield, peak, and failure forces by 1.6 times, 1.3 times, and 1.4 times, respectively, to those placed in a caudodistal (30 degrees) orientation. Kirschner wire insertion angle is an important consideration following tibial tuberosity osteotomy in dogs, with Kirschner wires placed at 0 degrees conferring increased resistance of the repair to construct deformation.

Temperature Changes during Implant Osteotomy Preparations in Human Cadaver Tibiae Comparing MIS® Straight Drills with Densah® Burs.

(1) Background: Several studies showed a sustained temperature of 47 °C or 50 °C for one minute resulted in vascular stasis and bone resorption with only limited bone regrowth over a 3–4-week healing period. The purpose of the present study was to evaluate the temperature changes (ΔΤ) that occur during the preparation of dental implant osteotomies using MIS® straight drills versus Densah® burs in a clockwise (cutting) drilling protocol. (2) Methods: Two hundred forty (240) osteotomies of two different systems’ drills were prepared at 6 mm depth at 800, 1000, and 1200 revolutions per minute (RPM), in fresh, unembalmed tibiae, obtained by a female cadaver. ΔΤ was calculated by subtracting the baseline temperature on the tibial surface, from the maximum temperature-inside the osteotomy (ΔT = Tmax − Tbase). The variables were evaluated both for their individual and for their synergistic effect on ΔΤ with the use of one-, two-, three- and four-way interactions; (3) Results: An independent and a three-way interaction (drill design, drill width, and RPM) was found in all three RPM for the Densah® burs and at 1000 RPM for the MIS® straight drills. As Densah® burs diameter increased, ΔΤ decreased. The aforementioned pattern was seen only at 1000 RPM for the MIS® straight drills. The usage of drills 20 times more than the implant manufacturers’ recommendation did not significantly affect the ΔΤ. A stereoscopic examination of the specimens confirmed the findings. (4) Conclusions: The independent and synergistic effect of drills’ diameter, design and RPM had a significant effect on ΔΤ in human tibiae, which never exceeded the critical threshold of 47 °C.

Temperature Changes during Implant Osteotomy Preparations in Fresh Human Cadaver Tibiae, Comparing Straight with Tapered Drills.

The success of osseointegration depends on many factors. With temperatures beyond a 47 °C threshold over 1 min, bone survival may be impaired. The purpose of the study was to evaluate, in fresh human cadaver tibiae, the temperature changes during osteotomy preparations using two straight and two tapered implant systems’ drills, external irrigation, and varying revolutions per minute (RPM). The tibiae from a fresh female cadaver were harvested bilaterally. Two tapered and two straight design drills were assessed. Two-hundred and forty osteotomies were prepared at 6 mm depth following the drill sequence of the manufacturers’ protocol for each drilling speed. Difference in temperature (ΔΤ) was calculated by subtracting the baseline from the maximum temperature (ΔT = Tmax − Tbase). Drill design and drill diameter, as independent variables or synergistically, had a significant effect on ΔΤ. Tapered drills: As the drill diameter increased, ΔΤ increased at all RPM. Straight drills: As the drill diameter increased, ΔΤ remained constant or slightly decreased at all RPM. Drill diameter and design had a significant effect on ΔΤ in human tibiae, which never exceeded the critical threshold of 47 °C. Tapered drills caused significantly greater heat production compared to straight drills.

Combined center of rotation of angulation-based leveling osteotomy and tibial tuberosity transposition: An ex vivo mechanical study.

To describe the technique of combined center of rotation of angulation (CORA)-based leveling osteotomy (CBLO) with tibial tuberosity transposition (TTT) and to compare the load to failure between CBLO combined with TTT and CBLO or TTT alone. Ex vivo study. Twelve pairs of cadaveric pelvic limbs. Six pairs of cadaveric tibia were tested in each group (CBLO-TTT versus CBLO) and (CBLO-TTT versus TTT) with each limb randomly assigned to a treatment group. Construct stability was determined by applying a tensile force to each patellar tendon until failure occurred. Load at failure and mode of failure were recorded for each specimen. No difference in mean load to failure was identified between CBLO-TTT (897 N) and CBLO alone (943 N) (P=.81). There was also no difference in the mean load to failure between the CBLO-TTT (928 N) and TTT alone (1046 N) (P=.12). Performing a TTT in combination with a CBLO does not weaken the construct failure to load when compared with each procedure performed alone. A combined CBLO and TTT could be considered a viable option for concurrent management of a cranial cruciate ligament deficient stifle and medial patella luxation.

Does bone penetration of cement differ by cement type and application time-point?

Intrusion of cement into bone is often considered an indirect indicator for implant stability in cemented joint replacement procedures. However, the influence of cement type (different viscosities/manufacturers) and application time-point on penetration of cements continues to be debated. This study aimed to quantify the effect of cement type and application time-point on the depth of penetration using porcine tibial specimens.Four different bone cements were applied to 60 resected porcine cadaveric tibias at three time-points within the working window (1, 2, and 3 min after dough time). Penetration was measured using computed tomography, utilizing two rigorous methods from the literature and a newly proposed volumetric method.Application time-point had a strong influence on the thickness of the cement layer above the resected tibia (0.25, 0.49, 0.73 mm at the three time-points). No significant variation in penetration depth metrics with cement type or application time-point was found, except percentage area covered by cement at 2 mm depth. This metric was significantly different between 1 and 3-minute time-points (12% and 6% respectively).Time-point of application had a significant influence on thickness of pure cement layer over resected bone. However, penetration depth was not significantly affected by cement type or application time-point. The clinical significance of these findings is that it may be better to apply cement relatively soon after dough time to avoid excessively thick cement mantle between implant and bone. Further, the choice of cement type may have minimal impact on cement penetration, indicating that long standing principles of good cement application maybe more important.

Weightbearing after combined medial and lateral plate fixation of AO/OTA 41-C2 bicondylar tibial plateau fractures: a biomechanical study

BackgroundCombined medial and lateral plate fixation is recommended for complex tibial plateau fractures with medial fragments or no cortical bone contact. Although such fixation is adequate to resist forces during range of motion, it may be insufficient to support immediate postoperative weightbearing. Here, we analyzed displacement, stiffness, and fixation failure during simulated full weightbearing of bicondylar tibial plateau fractures treated with combined medial and lateral locking plate fixation.MethodsWe used 10 fresh-frozen adult human cadaveric tibias and mated femurs. Osteotomies were performed with an oscillating saw and cutting template to simulate an AO Foundation and Orthopaedic Trauma Association (AO/OTA) 41-C2 fracture (simple articular, multifragmentary metaphyseal fracture). Specimens were anatomically reduced and stabilized with combined medial and lateral locking plates (AxSOS, Stryker, Mahwah, NJ). Specimens were loaded axially to simulate 4 weeks of walking in a person weighing 70 kg. The specimens were cyclically loaded from 200 N to a maximum of 2800 N. Then, if no failure, loading continued for 200,000 cycles. We measured displacement of each bone fragment and defined fixation failure as ≥5 mm of displacement. Construct stiffness and load at failure were calculated. Categorical and continuous data were analyzed using Chi-squared and unpaired t-tests, respectively.ResultsMean total displacement values after 10,000 loading cycles were as follows: lateral, 0.4 ± 0.8 mm; proximal medial, 0.3 ± 0.7 mm; distal medial, 0.3 ± 0.6 mm; and central 0.4 ± 0.5 mm. Mean stiffness of the construct was 562 ± 164 N/mm. Fixation failure occurred in 6 of 10 specimens that reached 5 mm of plastic deformation before test completion. In the failure group, the mean load at failure was 2467 ± 532 N, and the mean number of cycles before failure was 53,155. After test completion, the greatest displacement was found at the distal medial fracture site (2.3 ± 1.4 mm) and lateral fracture site (2.2 ± 1.7 mm).ConclusionsAlthough combined medial and lateral plate fixation of complex tibial plateau fractures provides adequate stability to allow early range of motion, immediate full weightbearing is not recommended.

Measuring Orthopedic Plate Strain to Track Bone Healing Using a Fluidic Sensor Read via Plain Radiography.

We describe a fluidic X-ray visualized strain indicator under applied load (X-VISUAL) to quantify orthopedic plate strain and inform rehabilitative care. The sensor comprises a polymeric device with a fluidic reservoir filled with a radio-dense fluid (cesium acetate) and an adjoining capillary wherein the liquid level is measured. A stainless-steel lever attaches to the plate and presses upon the acrylic bulb with a displacement proportional to plate bending strain. The sensor was attached to a plate in a Sawbones composite tibia mimic and a human cadaveric tibia. An osteotomy model (5 mm gap) was used to simulate an unstable fracture, and allograft repair to simulate a stiffer healed fracture. The cadaveric and Sawbones tibia were cyclically loaded five times (0-400 N) using a mechanical test stand, and fluid displacement was measured from plain radiographs. The sensor displayed reversible and repeatable behavior with a slope of 0.096 mm/kg and fluid level noise of 50-80 micrometer (equivalent to 5-10 N). The allograft-repaired composite fracture was 13 times stiffer than the unstable fracture. An analysis of prior external fracture fixation studies and fatigue curves for internal plates indicates that the threshold for safe weight bearing should be 1/5th-1/10th of the initial bending for an unstable fracture. The precision of our device (<2% body weight) should thus be sufficient to track fracture healing from unstable through safe weight bearing. The X-VISUAL fluidic sensor enables orthopedic plate strain quantification to monitor facture healing via X-ray imaging.

Standard versus customised locking plates for fixation of schatzker ii tibial plateau fractures

Aim3D-printed implants could improve the capture of fracture fragments for improved stability of tibial plateau fracture fixation. The aim of this study was to compare the biomechanical strength of fixation constructs using standard and customised 3D-printed proximal tibial locking plates for fixation of tibial plateau fractures. MethodsThis is a biomechanical study utilising six pairs of cadaveric tibiae. Fractures were created in an identical fashion using an osteotome and mallet, and fixed using either a standard, commercially-available proximal tibia locking plate or a customised 3D-printed plate. Design and production of the customised plates followed a “3D printing at point-of-care” model. Customised stainless steel 316 L plates were produced within a local additive manufacturing laboratory based upon pre-operative CT scans. Determination of implant choice within each cadaver pair was performed via simple randomisation. Following fracture fixation, the tibiae were skeletalised and biomechanically tested using a customised loading jig and a size-matched femoral knee prosthesis. The constructs were loaded cyclically from 100 N to approximately three times the cadaveric body-weight at 5 Hz for 10 000 cycles. Every 1000 cycles, the test was paused and the tibia was physically checked for failure. If failure had not occurred by the end of the testing cycle, the construct was loaded to failure and the load at which the construct failed was noted. ResultsFixation constructs using the 3D-printed plates performed comparably to those using the standard plates. There was no significant difference in the degree of fracture fragment displacement in both constructs. Overall longitudinal construct stiffness and load to failure was higher in the 3D-plates group but this did not reach statistical significance. ConclusionProduction of customised plates for proximal tibia fractures at point-of-care is feasible, however fixation constructs with these plates did not provide any biomechanical advantage over standard plates in terms of axial loading stiffness.

Angular stable locking in a novel intramedullary nail improves construct stability in a distal tibia fracture model

IntroductionIntramedullary nails are frequently used for treatment of unstable distal tibia fractures. However, insufficient fixation of the distal fragment could result in delayed healing, malunion or nonunion. Recently, a novel concept for angular stable nailing was developed that maintains the principle of relative stability and introduces improvements expected to reduce nail toggling, screw migration and secondary loss of reduction. The aim of this study was to investigate the biomechanical competence of the novel angular stable intramedullary nail concept for treatment of unstable distal tibia fractures, compared to a conventional nail locking in a human cadaveric model under dynamic loading. Materials and methodsTen pairs of fresh-frozen human cadaveric tibiae with a simulated AO/OTA 42-A3.1 fracture were assigned to 2 groups for reamed intramedullary nailing using either a conventional (non-angular stable) Expert Tibia Nail (ETN) with 3 distal screws or the novel Tibia Nail Advanced (TNA) system with 2 distal angular stable locking low-profile retaining screws. The specimens were biomechanically tested under conditions including initial quasi-static loading, followed by progressively increasing combined cyclic axial and torsional loading in internal rotation until failure of the bone-implant construct. Both tests were monitored by means of motion tracking. ResultsInitial nail toggling of the distal tibia fragment in varus and flexion under axial loading was lower for TNA compared to ETN, being significant in flexion, P = 0.91 and P = 0.03. After 5000 cycles, interfragmentary movements in terms of varus, flexion, internal rotation, axial displacement, and shear displacement at the fracture site were all lower for TNA compared to ETN, with flexion and shear displacement being significant, P = 0.14, P = 0.04, P = 0.25, P = 0.11 and P = 0.04, respectively. Cycles to failure until both interfragmentary 5° varus and 5° flexion were significantly higher for TNA compared to ETN, P = 0.04. ConclusionFrom a biomechanical perspective, the novel angular stable intramedullary nail concept provides increased construct stability and maintains it over time while reducing the number of required locking screws without impeding the flexibility of the nail itself and resists better towards loss of reduction under dynamic loading, compared to conventional locking in intramedullary nailed unstable distal tibia fractures.

Tibial Tuberosity Transposition Fixation with a Locking Plate during Medial Patellar Luxation Surgery: An Ex Vivo Mechanical Study.

The purpose of this study was to compare the load at failure, stiffness and mode of failure between three types of tibial tuberosity transposition fixation techniques: (a) pin and figure-8 tension band wire (Pin-TBW), (b) locking plate with pin and a tension band wire (Plate-Pin-TBW) and (c) locking plate with a pin (Plate-Pin). Six pairs of raccoon dog cadaveric tibiae were tested in Phase I Pin-TBW versus Plate-Pin-TBW and seven pairs in Phase II Plate-Pin-TBW versus Plate-Pin. One limb of each pair was randomly assigned to one of two groups for each phase. A tensile force was applied to the patellar ligament until construct failure. Pin-TBW (342N ± 54.7N) failed at a lower load than Plate-Pin-TBW (469N ± 77.3N), p = 0.00748, with all Pin-TBW failing by fracture and the majority of Plate-Pin-TBW failing by rupture of patellar ligament. Pin-TBW group Phase I, normalized with Plate-Pin-TBW Phase I, failed at a lower load than Plate-Pin group Phase II, normalized with Plate-Pin-TBW Phase II, p = 0.00467. There was no significant difference in mean load at failure, stiffness or mode at failure between the groups in the Phase II study. Although ex vivo mechanical testing does not replicate the postoperative live dog or cat, these results demonstrate lower construct strength of the Pin-TBW construct compared with the Plate-Pin construct in the raccoon dog cadaver model.

Effect of Bidirectional Insertion of External Skeletal Fixation Pins on Axial Pullout Strength in Canine Cadaveric Bone.

The aim of this study was to evaluate the effect of bidirectional insertion on axial pullout strength of tapered run out (TRO), traditional negative profile (TNP) and positive profile (PP) pins. Cadaveric adult canine tibiae were harvested. Tapered run out pins (Group 1) were inserted unidirectionally to the desired position; bidirectionally past the desired position, then withdrawn to the desired position (Group 2); and bidirectionally as described for Group 2, repeated twice (Group 3). Traditional negative profile pins (Group 4-6) and PP pins (Group 9-11) were placed in the same manner. Tapered run out (Group 7), TNP (Group 8) and PP pins (Group 12) were driven unidirectionally such that the shaft of the pin violated the cis-cortex. A servohydraulic testing machine extracted the pins and measured axial peak pullout strength. Positive profile pins had significantly greater pullout strength than TRO and TNP pins placed unidirectionally to the desired position. Method of insertion had no effect on peak pullout strength of TNP pins. TRO and PP pins inserted unidirectionally to the desired position had significantly greater peak pullout strengths than insertion bidirectionally or if the shaft of the pin violated the cis-cortex. The authors recommend that pins used for external skeletal fixation should be placed unidirectionally to the desired position with fluoroscopic guidance, intra-operative depth gauge measurements or measurements from preoperative radiographs. Repositioning pins results in loss of peak pullout strength with TRO and PP pins.

Rethinking the Coronal Anatomic Axis of the Distal Tibia for Intramedullary Nail Placement: A Cadaveric Study.

Background: Recent studies have reported that targeting a center-center position at the distal tibia during intramedullary nailing (IMN) may result in malalignment. Although not fully understood, this observation suggests that the coronal anatomic center of the tibia may not correspond to the center of the distal tibia articular surface. Questions/Purposes: To identify the coronal anatomic axis of the distal tibia that corresponds to an ideal start site for IMN placement utilizing intact cadaveric tibiae. Methods: IMN placement was performed in 9 fresh frozen cadaveric tibiae. A guidewire was used to identify the ideal start site in the proximal tibia and an opening reamer allowed access to the canal. Each nail was then advanced without the use of a reaming rod until exiting the distal tibia plafond. Cadaveric and radiographic measurements were performed to determine the center of the nail exit site in the coronal plane. Results: Cadaveric and radiographic measurements identified the IMN exit site to correspond with the lateral 59.5% and 60.4% of the plafond, respectively. Conclusions: Tibial nails inserted using an ideal start site have an endpoint that corresponds roughly to the junction of the lateral and middle third of the plafond. Further studies are warranted to better understand the impact of IMN endpoint placement on the functional and radiographic outcomes of tibia shaft fractures.