Bulk Ore Research Articles

Ventilation of large section blind headings under conditions of changing ore load size

Relevance. The need to ensure safe working conditions in the working areas of underground mines. Stagnant zones with low air velocities can be formed in large section blind heading behind the ore bulk when ore is shipped by mining machines. There is a possibility of the formation of local gas accumulations and their abrupt removal later in such stagnant zones due to the unsteadiness of accumulation and transfer of gas impurities in a blind heading. A sharp removal of gas will lead to contamination of the load-haul-dump operators’ workplace. Aim. To identify removal of exhaust gases in large section blind headings in conditions of changing ore load size. Objects. Large section blind headings with of complex geometry. Methods. Three-dimensional numerical simulation of unsteady turbulent flow of a gas-air mixture in the Ansys CFX, visualization and analysis of simulation data in the Wolfram Mathematica. Results. The paper presents the results of mathematical modeling of ventilation of large section blind headings of complex geometry under conditions of changing ore load size formed during mining operations by the load-haul-dump machines with an internal combustion engine. It is shown that either a single vortex is formed that ventilates the blind headings space, or a stagnant zone behind the bulk ore, which is characterized by a relatively low intensity of mass transfer. Vortex formation depends on the height of the ore bulk. The authors have obtained the dependences of the change in the average concentration of exhaust gases at the outlet of the blind headings space on the operating time of the machine. They determined the dependence of the correction volume coefficient on the geometric parameters of the blind headings. An analytical model of the removal of gases from the blind headings space under conditions of changing bulk ore volume is obtained. The expression of increment in gas concentration on an operator’s workplace makes it possible to derive formula to find maximum time of load-haul dump operation in a stope such that gas concentration is never higher than maximum allowable concentration.

Arsenopyrite from the Low-sulphidation Sedefche Au-Ag deposit, Eastern Rhodopes: Mineral Association and Gold Potential

The Sedefche Au-Ag deposit is located in the eastern Rhodopes, Bulgaria and is part of the Zvezdel-Pcheloyad ore field. The deposit is of low-sulphidation epithermal type, hosted in Oligocene highly silicificated intermediate volcanic tuffs, which lie above shallow marine sediments of organogenic limestones. The orebody has stratiform shape partly outcroping onto the surface. The ore mineralization is represented by small crystals and fine grained aggregates of sulphides (mainly pyrite, arsenopyrite, marcasite, chalcopyrite, galena, sphalerite) and associated sulphosalts (tetrahedrite, pyrargyrite, freibergite, and miargyrite) within matrix of quartz, formed in several stages of deposition. Gold in the deposit is detected in significant amounts in bulk ore samples, while native gold (a single < 1 μm gold nugget) and gold-bearing phases were sporadically discovered. The form of gold presence in the deposit is nevertheless debatable. Using combined SEM-EDS, EPMA and LA-ICP-MS approach, the highest concentrations of gold have been established in the arsenopyrite – the gold content there is up to hundredfold higher than in other ore minerals being potential concentrators of gold such as pyrite, marcasite and chalcopyrite. The presence of gold in arsenopyrite predominantly as nanoparticles, irregularly disseminated in the crystals as clusters of inclusions is suggested.

An investigation on pyrite floatability using stable micro-nanobubble-assisted flotation

This study critically examines the impact of micro-nanobubble (MNB)-assisted flotation on pyrite recovery in bulk ore, and clarifies the intricate relationship between pyrite and its associated ore. The physicochemical properties of MNBs and the interaction mechanisms between xanthate collector and pure pyrite mineral were evaluated using advanced analytical techniques, including Dynamic Light Scattering (DLS), Field-Emission Scanning Electron Microscopy coupled with Energy-Dispersive X-ray Spectroscopy (FESEM-EDX), and Ultraviolet-Visible Spectroscopy (UV-Vis), in the absence and the presence of MNBs. MNBs were created through hydrodynamic cavitation, and their characteristics revealed a size increase from 600 nm to 3 µm over 25 days. Notably, the zeta potential measurements indicated an increase from -2.5 to 0 mV at a constant pH of 8, correlating with the geometric mean size of MNBs coarsening from 600 nm to 2-3 µm. The FESEM and EDS analyses disclosed that ultrasonic treatment effectively dispersed ultrafine surface coatings on pyrite particles, increasing iron and sulfur purity by 8% and 6%, respectively, and significantly reducing surface oxygen by 53%. Micro-flotation and batch rougher kinetic flotation experiments were conducted with and without MNBs, leading to a 7% and 8% improvement in recovery for pyrite mono-minerals (-105+53 µm) and its ore (d<sub>80</sub>=150 µm), respectively. The sorption behavior of sodium isopropyl xanthate (SIPX) collector on the particle surface was also investigated at various concentrations (ca. 10-160 µM) in the presence and absence of stable MNBs and demonstrated that the presence of MNBs resulted in a 1.6-fold increase in collector absorption on the pyrite surface, confirming the findings obtained from micro-flotation. Moreover, adsorption behavior is up to 1.3 times compared to the scenario without MNBs. The adsorption process was controlled by a pseudo-second-order model, indicating a chemical sorption mechanism.

The effect of stope size and cut-off grade on the design and scheduling of an underground mining operation in the presence of a pre-concentration system

ABSTRACT Stope layout optimisation is considered one of the main steps in the design and strategic planning of underground mining operations. This paper investigates the influence of stope size and cut-off grade in an underground sublevel stoping operation in the presence of a preconcentration system using a newly developed mathematical optimisation model. The utilisation of a bulk ore sorting system, its effects on the resource utilisation, and the final discounted cash flow of a case study are presented. Results show that incorporating a bulk sorting system to a sublevel stoping operation can significantly increase the viability of a deposit.

A new insight into the mechanism of MNB-assisted flotation of copper: A link between chalcopyrite and its-bearing bulk ore

The present study systematically explores the relationship between chalcopyrite mono-mineral and copper-bearing ore flotation in the presence and absence of micro- and nano-bubbles (MNBs). Ultrafine bubbles were generated through a cavitation mechanism, and their stability, size, and zeta potential were monitored over a period of 0–25 days. Micro-flotation and batch rougher kinetic flotation experiments were carried out with and without ultrafine bubbles using a modified Hallimond tube and 2.5 L Denver® flotation cell, respectively. The results showed that the presence of MNBs improved the recovery of chalcopyrite mono-mineral and its ore by 24.5 % and 7 %, respectively. Furthermore, the adsorption behavior of sodium isopropyl xanthate (SIPX) collector at various concentrations was analyzed in the presence and absence of stable MNBs using UV–visible spectroscopy, FTIR analysis and kinetic models. The adsorption studies supported the micro-flotation findings, demonstrating that the presence of MNBs not only boosted collector adsorption on the chalcopyrite surface (by an average of 73.8 %) but also improved the adsorption kinetics (by 69.44 %). The sorption kinetics followed the pseudo 2nd order model in the presence of MNBs, while in the absence of MNBs, both pseudo 1st order and pseudo 2nd order models were observed. The sorption of SIPX onto chalcopyrite was identified as a chemisorption process in the presence of MNBs, whereas it was a physicochemical sorption in the absence of MNBs.

Using Hg isotopes and trace elements to constrain the origin of the Ordovician Xiangquan Tl deposit, South China

Sediment-hosted stratiform sulfide (SHSS) deposits commonly contain large amounts of strategic metals, such as Tl, Hg, Cd, Ge and Ga, however, sources of these metals remain debate. Here we present new elemental and Hg isotopic data to constrain the metal sources for the Xiangquan Tl deposit (South China), a unique SHSS deposit with 250 t Tl at an average grade of 928 ppm. Stratiform pyrite orebodies are hosted in the Ordovician marine sedimentary succession of mostly limestone with minor mudstone. Pyrite, the dominant ore mineral, is rich in Hg (up to 1360 ppm). Bulk ores and pyrite separates from this deposit have significant variations of δ202Hg (−5.48 to −0.65 ‰) and Δ199Hg (−0.01 to 0.36 ‰). The Δ199Hg values are mostly positive, similar to those of seawater and marine sediments. Ore petrography, trace element enrichment coefficients, rare earth element patterns, Re-Os ages (478 ± 33 Ma) and S isotope compositions of pyrite indicate that Hg and other metals were derived from hydrothermal fluids venting at the seafloor. We suggest that the ore-forming fluids of the Xiangquan deposit were predominantly originated from large-scale circulation of evolved seawater, which leached Hg and Tl from the marine country rocks. These metal-rich fluids migrated upward, vented to the seafloor, and mixed with anoxic H2S-rich seawater to precipitate Hg- and Tl-rich pyrite. Our study highlights that the combined application of Hg isotopes and trace elements could be used to trace the sources of metals in hydrothermal ore deposits such as SHSS deposits.

A bulk sorting trial of copper ore using a magnetic resonance analyser

Sensor-based bulk ore sorting (BOS) is a technique that may lead to uplift of processing grades by excluding waste as well as an increase in usable resource by sorting material designated as mineralised waste. A magnetic resonance analyser (MRA) was installed on the primary crushed ore feed to the sulphide plant at the Kansanshi copper mine in northwestern Zambia to trial BOS. The conveyor belt operated at 2800tph and carried ore of which greater than 85% by weight of the copper-bearing minerals are chalcopyrite. The MRA was therefore tuned for chalcopyrite’s zero static field magnetic resonance. The analyser achieved a 3σ detection limit of 0.045 wt% copper as chalcopyrite over a 4 s measurement time and standard belt loading, with lower detection thresholds possible if the measurement time increased.A trial of ore diversion was then carried out at the site. Pods of ore measured as less than 0.2 wt% copper as chalcopyrite by the MRA were diverted by a dead box diverter system to form a low-grade stockpile of approximately 10,000 tonnes. A cavity in the mill feed stockpile was arranged and the rejected material fed back through the crusher, past the MRA and directly through the milling circuit to the flotation feed where a Vezin sampler was used to take a sample every 5 min. This sample was then tested for copper grade by the site metallurgical laboratory. The MRA measured a grade of 0.16 wt% copper as chalcopyrite over the test time period and the Vezin samples for the last hour of the trial reported approximately 0.2–0.3 wt% copper despite some mixing with unsorted ore being inevitable. This is as clear a demonstration of bulk ore sorting (BOS) as practically achieveable in the production environment at Kansanshi and, to the author’s knowledge, the first demonstration of BOS on a copper ore stream of at least this throughput.

Improvement of the stoping technology in mining magnetite quartzite by underground methods

The ore deposits in Kryvyi Rih iron ore basin are mined using bulk ore and overlying rocks caving systems. These mining systems have a significant drawback, namely a 2 – 5% reduction in the iron content of the mined ore mass when mining rich ores and up to 15% when mining poor ores. Current technological solutions enable improvement of ore extraction values while increasing economic costs by 15 – 20%. Therefore, the present article proposes a technological solution that will improve extraction values for poor ores. The study conducted results in determining the optimal distance between drawpoints of the receiving level and substantiates location of additional workings in the footwall, which reduces ore losses and increases ore mass extraction values. The proposed technological solution will reduce ore losses by 10 – 15% of the standard losses and increase ore extraction values by 5 – 15%, while reducing iron content by 5 – 7% of the initial one. Thus, the study conducted proves that the use of an additional level located 30 – 35 m above the main receiving level allows reduction of ore losses from 27.39% to 21.19%, and the iron content in the extracted ore mass – by only 3% instead of 12%.

Tracking Grade Heterogeneity in a Panel Cave Mine: A Reconciliation Study Investigating the Impact of Mixing from an Ore Sorting Perspective

Bulk ore sorting is a preconcentration method applied to bulk streams or batches of material. The effectiveness of bulk ore sorting relies on the degree of the naturally occurring in situ grade heterogeneity of an ore deposit. The blending of ore during mining and material handling degrades the in situ grade heterogeneity initially present in an orebody and reduces the potential to apply bulk ore sorting. Block and panel cave mines experience mixing from the establishment of caves to the delivery of the caved ore to concentrators. This study focused on tracking the grade heterogeneity and quantifying the impact of mixing on the sorting potential of the Cadia East panel cave mine via the reconciliation of the grade measurements performed at different locations. The results showed that the copper and gold grades were almost fully homogenized via various mixing events identified for the mine. The tracked grade heterogeneity values revealed that the mixing during material handling, which included ore blending according to mine planning, reduced the grade variability more drastically than the mixing within the caves. As the ore travelled from its original in situ location, the grade distributions gradually transformed, and the grades eventually normalized around the mean values. Only insignificant amounts of low-grade material that could have potentially been discarded were reported to the on-belt sensor located at the surface. The results of this study are significant for cave mines exploring sorting systems for preconcentration as they highlight how mixing can impact the variability in ore grades.

Study on the Effect of Ore-Drawing Shear Factor on Underground Debris Flow in the Block Caving Method

The shear factor of ore drawing is an important factor affecting the formation of underground debris flows. The aim of this study was to investigate the effect of the mining shear factor on underground debris flows in natural caving. The research background was the underground debris flow in the Plan copper mine, and we analyzed the characteristics of the slurry material structure of the underground debris flow, as well as the influence of the ore-drawing shear factor on the formation mechanism of the underground debris flow. The results showed that the slurry of the underground debris flow in the Plan mine is both a pseudoplastic and thixotropic fluid. Shearing force induced in drawing deforms the slurry and decreases its viscosity with the increase in shear rate and time. The shear force produced by the flow of ore particles first produces shear action on the paste in the shear boundary region of the ore drawing, reducing the paste viscosity while increasing its fluidity. Consequently, the “activation” makes the paste flowable, which flows along with the bulk ore flowing through the drawing mouth. The continuous ore-drawing process continuously shears the new moraine slurry in the ore-drawing channel and continuously “activates” the moraine slurry in the ore-drawing channel. Finally, destructive underground debris flow accident of a certain scale occurs. To our knowledge, this study thoroughly investigated the effect of the ore-drawing shear factor on the formation mechanism of underground debris flows, which not only broadens the research field of debris flow but also covers the deficiency of systematic research on underground debris flows, providing theoretical guidance for the prevention and control of underground debris flows.

Geobotanical and Biogeochemical Prospecting Method of Complex Sulphide Ore of Pb-Zn-Cu-Ba in Abuni-Adudu areas of the Middle Benue Trough, Nigeria

This research work focused on two plant species namely, the Anogeissus leiocarpus (DC.) and Dichrostachys cinerea for mineral prospecting. The two plants were sampled based on their occurrence, abundance and outlook. Twelve samples (six each of Anogeissus leiocarpus (DC.) and Dichrostachys cinerea) were collected around Abuni-Adudu mining communities in the Middle Benue Trough, Nigeria. In addition, bulk ore and twelve soil samples were also collected and analysed for correlation. Geologically, the study area is made up compacted shale, baked shale (hornfels), and sandstones of sedimentary origin, which are intruded by tertiary basalts of igneous origin. Samples were analysed for elemental composition, using inductively coupled plasma mass spectrometry method. Analysis revealed that the geobotanical method of prospecting for Pb-Zn-Cu-Ba mineralization in the area is promising as biogeochemical data indicated that the Dichrostachys cinerea are good indicator of Pb-Zn-Cu mineralization while the Anogeissus leiocarpus were indicative of Barium. Given the relatively low concentration of Barium in the ore (3.8 ppm) as against concentration in the soil samples, which ranges from 83 ppm (sample YS6) to 552 ppm (sample YS12), Barium has its source from the shale and sandstone or nearby Barite mineralization and not the ore.

Key factors determining the bulk ore sorting potential in a caving mine

Bulk ore sorting may add significant value to block and panel cave mines where processing feed grades are constrained by limited grade selectivity. The Cadia East gold-copper mine is a panel caving operation utilizing two different on-belt bulk ore sensors to evaluate the potential benefits of the technology. To date, there is limited reported work addressing the applicability of bulk ore sorting systems at a caving mine, where two commodities drive the economics. This indicative study is aimed at investigating the importance of various key factors on the bulk ore sorting potentials of the active and future panel caves of the Cadia East mine. Results show that for only one active cave of the mine, bulk ore sorting may be applied in the ideal scenario where grades are not affected negatively by mixing and the sorting takes place at maximum efficiency. As a general trend for all the caves, when the sorting cut-off grade is increased beyond a certain threshold, a sharp decline is observed in the sorting potentials due to the significant amounts of gold and copper deporting to the sorter rejects. In the case of a significant drop in metal prices, bulk ore sorting may only provide an opportunity to improve cave economics marginally. Results obtained by investigating the spatial change in sorting potential show that the portions of the caves with low metal grades are favourable for bulk ore sorting. In the scenario where bulk ore sorting is focused on low-grade portions, it is demonstrated that improvements in the economics of the future caves may additionally be achieved. However, as the low-grade portions represent a very small volume in the orebody, applying ore sorting on the plant conveyor may not be viable.

Paleo‐Pacific Plate Subduction and Basement Mobilization Triggered Large‐Scale Formation of Mesozoic Gold Deposits in the Northern Margin of the North China Craton

AbstractThe northern margin of the North China Craton (NNCC) hosts Mesozoic gold deposits of significant economic importance. The metal sources of these gold systems have long been debated with mainly magmatic‐hydrothermal versus metamorphic fluid models. Mercury (Hg) isotopes, which undergo unique mass‐independent fractionation, can provide important insights into the source of metals in gold deposits due to the close association between Hg and Au in such systems. Here, we investigated the Hg isotopic composition of six gold deposits of the Middle Jurassic to Early Cretaceous age and potential source rocks in the NNCC. Variable ∆199Hg values were observed in bulk ore and pyrite samples (−0.28‰ to 0.34‰, n = 51) and coeval granites (−0.21‰ to 0.13‰; n = 25). The negative ∆199Hg values of bulk ore and pyrite samples mostly agree with that observed for metamorphic basement rocks (−0.37‰ to 0.11‰; n = 32). The positive ∆199Hg values of bulk ore and pyrite samples agree with those reported in marine sediments (0‰–0.3‰). So the data suggest binary mixing of ocean‐recycled Hg originated from the subducted oceanic slab, and terrestrial‐recycled Hg from the Precambrian basement in Mesozoic gold deposits. The contribution of Hg (and Au, by analogy) from both reservoirs varies depending on active continental arc versus intracontinental setting and is ultimately controlled by translithospheric heat flow driven by paleo‐Pacific plate subduction.

A conceptual strategy for effective bulk ore sorting of copper porphyries: Exploiting the synergy between two sensor technologies

Bulk ore sorting is a preconcentration technique that may address the operational and environmental challenges of extracting low-grade ore deposits, such as copper porphyries. The technique allows for the early detection and diversion of sub-economic material by sensor-diverter systems before milling, thereby improving mill feed quality and reducing environmental impact. Grade heterogeneity in ore and sensor capability to measure grade accurately are prerequisites to applying bulk ore sorting. The technical synergy between the responses of multiple bulk ore sorting technologies can aid in taking full advantage of the grade heterogeneity existing in sorter feed while providing accurate and precise grade measurements. This study is aimed at quantitatively demonstrating the potential benefits of a conceptual strategy of integrating the responses from two sensor technologies for bulk ore sorting of copper porphyry deposits. Results show that a more significant enhancement in the Net Smelter Return (NSR) of the ore can be achieved by the simultaneous employment of the magnetic resonance (MR) and prompt gamma neutron activation analysis (PGNAA) sensors compared to the bulk ore sorting scenarios in which the sensor technologies are utilized separately. Results are encouraging and can prompt the collaboration of sensor manufacturers and mining companies to prove the actual value of the presented concept by performing on-site trials.

Deployment of XRF Sensors Underground: An Opportunity for Grade Monitoring or Bulk Ore Sorting in Cave Mines

Ore grades are monitored regularly in cave mines through drawpoint sampling. Automating grade monitoring through deploying X-ray fluorescence (XRF) sensors on the buckets of production loaders has been proposed as an alternative approach to address the issues around the traditional practice of drawpoint sampling. Bucket-mounted sensors can also be employed for bulk ore sorting underground. This study is aimed at evaluating the deployment of XRF sensors on production loaders as an opportunity for grade monitoring or bulk ore sorting in caving operations. The mill feed grade prediction performances of the drawpoint sampling program and mine planning software were assessed for the Cadia East panel cave mine. The results showed that the drawpoint samples underestimated the mill feed quality during a 10-month investigation period. The cave portions with bulk ore sorting potential were linked to the extraction level layout to estimate the number of drawpoints where sensors could be situated for diverting ore and waste. Samples obtained from the mine were tested to evaluate the ability of a lab-scale proxy of a bucket-mounted XRF sensor system to measure copper and gold grades. R-squared values of 0.84 and 0.68 were achieved between the predicted and measured copper and gold grades of the samples, respectively. Sensor test results are promising in revealing the potential to utilize XRF sensors underground. Future test work is encouraged to further validate the applicability of XRF sensors in an underground mining environment.

Simulating Bulk Ore Sorting Performance of a Panel Cave Mine: A Comparison between Two Approaches

Conceptual bulk ore sorting studies are essential for determining a potential improvement in mine economics before undertaking on-site sensor trials. Two approaches, block modelling and drill core compositing, are applied to simulate the bulk ore sorting performance of mining operations. While one employs the grade data of a block model, the other approach utilizes composited drill core grades. This study aimed at comparing these two approaches by estimating in-situ grade heterogeneities and simulating the bulk ore sorting performances of the currently active caves of the Cadia East panel cave mine. The results show that block modelling tends to smooth the grade variability that initially exists in the drill core grade data. Particularly in the portions of the deposit where drilling is sparse or widely spaced compared to the selected block size, block modelling leads to lower grade heterogeneity and bulk ore sorting performance estimates. However, when the drill hole data is nonrepresentative of the area of interest, block modelling can predict more realistic bulk ore sorting performances compared to drill core grades. The assessments performed with the blocks and drill core composites of various sizes showed that grade heterogeneity was adversely affected by an increased sorting scale due to averaged metal grades.

Palladium, platinum, selenium and tellurium enrichment in the Jiguanzui-Taohuazui Cu-Au Deposit, Edong Ore District: Distribution and comparison with Cu-Mo deposits

The Jiguanzui-Taohuazui Cu-Au deposit is located in the Edong ore district, Middle–Lower Yangtze River metallogenic belt, eastern China. The deposit is palladium, platinum, selenium and tellurium enriched; however, the distribution of these metals is unclear. Three mineral assemblages of ore in the deposit have been identified, namely: a magnetite-bornite-chalcopyrite-(hematite) assemblage (Mt-Bn-Cp-Hm), a chalcopyrite-pyrite assemblage (Cp-Py), and a pyrite-chalcopyrite-(sphalerite) assemblage (Py-Cp-Sph). Forty-eight bulk ore assay results show high concentrations of up to 66.9 ppb for Pd, 5.9 ppb for Pt, 150 ppm for Se and 249 ppm for Te. The high temperature Mt-Bn-Cp-Hm assemblage (530–380 °C) is enriched in Pt and Pd, whereas the Py-Cp-Sph assemblage in the marble-replacement ore (300–220 °C) hosts the major Se and Te mineralization. Palladium, Pt, and Se are mostly hosted in sulfide minerals, whereas Te is hosted in tellurides and Bi-Te-S sulfosalt minerals. Building on previous experimental and thermodynamic calculations, we propose the major controls on the Pd and Pt distribution in the deposit are temperature and salinity, whereas the Se and Te mineralization is promoted by the precipitation of major sulfide phases such as pyrite, chalcopyrite and sphalerite.A comparison of the ores from the Jiguanzui-Taohuazui Cu-Au and Tongshankou Cu-Mo deposits in the Edong ore district shows that the Cu-Au deposit has higher PGE and Te, but similar Se concentrations. This scenario is consistent with the average grades and bulk ore contents of these elements from global (oxidized) porphyry (±skarn) Cu deposits. This suggests that the saturation of magmatic sulfides in the magma chamber as a result of higher proportion of crustal S-rich and/or reduced material contamination can be detrimental for PGE and Te enrichment processes, and thus, Cu-Au porphyry (±skarn) deposits have more potential for higher Pd and Te concentrations than the Cu-Mo deposits.

Mineralogy and Geochemistry of Gold Mineralization at Southern part of Ulu Sokor Gold Deposit, Kelantan, Malaysia

The Ulu Sokor gold deposit is classified as orogenic type deposit with evidence from previous studies on the structural, mineralogical, alteration, fluid inclusion, and stable isotope data. This study focuses on the mineralogy and geochemical analysis of representative ore rock samples from southern part of Ulu Sokor gold deposits. The project area is situated at the North of Kelantan state which lies on the Central Belt of Peninsular Malaysia. The main objective of this research is to determine the gold mineralization enrichment pattern relative to other trace elements based on the new data of mineralogy and geochemical analysis. Gold mineralization is primarily hosted in structurally controlled quartz vein which occurs in various degrees of ductile-brittle environment. Based on the field relationships, ore microscopy and geochemical data analysis, there are two main gold mineralization type in the southern part of Ulu Sokor gold deposit, namely (1) Gold associated and as inclusions in bismuthinite based on the mineralogy study, and (2) Refractory gold occurs as lattice bound in pyrite based on the Au/As molar ratio. In terms of mineral exploration and gold prospecting, the significant enrichment in this study area is Bi. However, some other metals can also be considered as a significant value in this area such as Pb, As, Cu and Zn. From the bulk ore chemistry, the geometric mean values of Au and Bi are 1.9 ppm Au (n=23) and 96 ppm Bi (n=22), respectively. The knowledge base for bismuth minerals in Malaysia would provide a significant targeting clue for the gold mineralization.

Method for quick assessment of cohesive ore flowability

Beneficiation of iron ore with natural moisture has become increasingly relevant, either due to restrictions on wet operations, which result in disposal of tailings in dams, or due to the possibility of ready blending of various ore types. A great difficulty in these operations is handling of hydrated ores, with the presence of clay minerals, or with a higher moisture content. Effective techniques to facilitate handling emerge as the main challenge to make it possible to treat these ores under natural moisture in different plants around the world. This work aims at presenting a method for expeditious appraisal of the flowability of cohesive ore. A sample of iron ore from Mina do Pico, Brazil, was used in this study. The flowability was investigated under different conditions, using a bench scale rectangular trough with controlled slope. The following liners were studied: ASTM A-36 carbon (CDP), ultra-high molecular weight polyethylene (UHMW), Hardox, natural rubber, Arcoplate and polyurethane. UHMW resulted in the best flow efficiency and the lowest friction angle between bulk ore and the lined wall. Vibration as an ancillary agent for mechanical discharge significantly improved the flow efficiency.

Investigation on influential factors of bulk ore sortability based on fractal modelling

The uptake of bulk ore sorting technology is hindered by little knowledge in assessing its applicability for certain mine operation. The applicability of the bulk ore sorting technology, referred to as ‘sortability’, is a multi-folded concept and is influenced by many factors. Researchers have investigated the influence of some of the various factors, but few have done this in a holistic perspective and in a quantitative manner. In this research, nine influential factors of ore sortaibility were integrated in a mathematical framework based on fractal modelling approach. Box-Behnken design was applied and 130 block cave mine operations were hypothesized under different values of the factors. The influence of the factors on the ore sortability were investigated and factors of significant influence were identified. Results showed that ore property, sorting efficiency, metal price, processing cost and operation scale were the most significant factors in affecting the sortability for a mine operation. The research is intended to improve the understanding on the bulk ore sortability for mine productions under different conditions, and to provide a holistic perspective for applying the bulk ore sorting technology.