Buck-boost Power Factor Correction Research Articles

Fully Soft-Switched Buck–Boost Bridgeless PFC Converters With Single-Magnetic Core

This paper proposes new fully soft switched bridgeless buck-boost power factor correction converters using single magnetic core with capability of realizing positive or negative output voltages. Full ZVS operation is provided for the main switches independent of the load and grid voltage variations. Also, the proposed converters have common ground and single ended output which increase power density and alleviates common mode noise. The proposed converters operate under discontinuous conduction mode (DCM) to shape the input current inherently. A 120W, 100kHz laboratory prototype with negative output voltage is implemented to verify the theoretical analysis and the effectiveness of the proposed topologies. The results demonstrate efficiency of 96.2% and total harmonic distortion (THD) of 4% at full load condition.

PI Controller Based Power Factor Correction Circuit for Plug-in Hybrid Electric Vehicle Using Solar Charging Module

The electrical vehicle requires power without losses or harmonics. The proposed method utilizes PV (photovoltaic)solar module as an input source, a converter of boost DC-DC buck incorporate for power peaks maximum in getting with MPPT approach, and the SPWM (Sinusoidal Pulse Width Modulation) inverter improves the performance by option shift in phase shift varying on the circuit. This aims to reduce the total harmonics distortion, losses switching, and improve the power factor. By varying the module of PV irradiances and temperature, the power is generated and it is peak power for utilizing maximum with MPPT (Maximum Power Point Tracking) that has been tracked. The Buck-Boost PFC (power factor correction) converter is used; when it performs the active state of PV, the Buck mode is utilized; if no power supplies the circuit, the boost mode will act to supply the SPWM inverter mode. Here the PI controller is applied for reducing the harmonics and stores on charging unit of EVs. The result simulated obtains the circuit electricity utilized by source result, which improves the performance by the effective charging station, which is applicable for EVs charging module. Overall, the method proposed is done with MATLAB/Simulink tool with the adaptation of 2018a.

Design and Control of Two Stage Battery Charger for Low Voltage Electric Vehicles Using High Gain Buck-Boost PFC AC-DC Converter

The design and control of a two-stage onboard battery charger (OBC) for the low-voltage electric vehicle (LVEVs) are presented in this study. The presented charger operates over a wide range of AC input voltage at high power factor. The presented charger utilizes a bridgeless high gain high power factor AC-DC converter with continuous input current characteristics at its front end. At the back end of the charger, an isolated Cuk DC-DC converter is employed to control and implement different battery charging modes, viz. constant current (CC) and constant voltage (CV) charging profiles. The presented AC-DC converter operates under discontinuous current mode (DCM) operation and achieves minimum control complexity at the AC-DC stage. The DCM design and high voltage conversion ratio allow it to function reliably over a comprehensive range of input and intermediate DC link voltage. This study covers the charger's design for a power rating of 650 W and output battery voltage of 24 to 72 V. The overall operational analysis and effectiveness of the design are verified through both simulations and experimental implementation and the performance is compared with other contemporary power factor correction (PFC) topologies on various parameters.

A Soft-Switching Bridgeless Buck-Boost Power Factor Correction Converter With Simple Auxiliary Circuit and Low Input Current THD

In this paper, a new bridgeless (BL) buck-boost power factor correction (PFC) converter using pulse width modulation (PWM) control is presented. The introduced structure operates in discontinuous conduction mode (DCM) to achieve the sinusoidal form of the input current inherently. The proposed converter utilizes a simple zero voltage transition (ZVT) circuit in which the auxiliary switch is turned ON and OFF under zero current switching (ZCS) condition, and the main switches turn ON and OFF under zero voltage switching (ZVS). Moreover, all diodes are turned OFF under ZCS condition, and the reverse recovery problem is solved. By reducing the number of semiconductor elements in the current flow path, conduction loss is minimized. Also, the proposed structure utilizes only one magnetic element. The above-mentioned advantages along with a low total harmonic distortion (THD) and high efficiency are the main benefits of the proposed structure compared to previous topologies. In addition, unlike the BL-buck converter, the input current dead angle is omitted without adding any extra components. Finally, a 500 W-100 kHz prototype at 90-265 Vrms input and 96 V output is implemented to verify the theoretical analysis and it illustrates the efficiency of 97.35 % and the input current THD is about 2.7 % at 220Vrms input voltage.

An Electrolytic-Capacitor-Less PFC LED Driver With Low DC-Bus Voltage Stress for High Power Streetlighting Applications

This paper presents a single-stage, soft-switching, high power factor, flicker-free LED driver without any electrolytic capacitors for streetlighting application. The proposed LED driver consists of a buck-boost type power factor correction (PFC) circuit integrated with an asymmetric half-bridge LLC resonant converter. The buck-boost type PFC circuit provides a high power factor, low input current harmonics, and low dc bus average voltage. Unlike other methods that use the first harmonic approximation (FHA) analysis or the differential equations in time domain to analysis the LLC circuit, in this paper, a Fourier series-based analysis is proposed. The proposed method provides better accuracy in comparison with the FHA while being simpler than the time domain analyze method. The half-bridge LLC resonant converter is designed such that ZVS is obtained for the entire input voltage range (185 <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$-$</tex-math></inline-formula> 265 <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$V_{rms}$</tex-math></inline-formula> ), and for 20% to 100% of the full-load power. In addition, a magnetic integration technique is utilized to increase efficiency and reduce converter size. The designed control system enables lowering the output current ripples without using any electrolytic capacitors. To verify the feasibility of the proposed LED driver, a 200 W prototype is implemented. The proposed LED driver achieves maximum efficiency of 94.6%, high PF, and a maximum of 15% output current ripples.

Efficient Soft Switching Single-Stage PFC for Low-Power Applications

Single-stage (SS) power factor correction (PFC) converters are applied as the power supply for low-power devices. Usually, the flyback converter is merged with the PFC stage to eliminate the reset winding required for the transformer. This article merges a new resonant forward converter with the buck-boost PFC stage. Thus, reset winding of the forward converter is eliminated while soft switching is achieved. Due to the low flux of the forward transformer core, transformer volume is reduced. Also, for the same volume of the transformer, transformer losses can be reduced in comparison to the flyback converter. The proposed converter is analyzed, and design considerations are discussed. A prototype converter is implemented. According to the experimental results, high efficiency and low total harmonic distortion (THD) are achieved.

Reducing Low-Frequency Ripple Using Alternative Output Capacitor Connection on Integrated Converters for LED Drivers

Although advantageous in several aspects, the integration of converters leads to a loss of independence between the converter's stages, since both stages are controlled by the same active switch. This condition makes it impractical to adopt control techniques that act on the duty-cycle to mitigate the low-frequency ripple at the output current without distorting the line current. The low-frequency ripple transferred from the bus voltage to the LED current has been studied for integrated converters operated at constant duty-cycle. To comply with IEEE 1789-2015 recommendation, the integrated converters use large capacitors to mitigate the low-frequency ripple. Converters operating in discontinuous conduction mode (DCM) have been widely adopted because they transfer less ripple to the output than converters operating in continuous conduction mode (CCM). A novel circuit arrangement for the buck-boost power control (PC) stage integrated with a buck-boost power factor correction (PFC) stage is explored in this paper as a technique to minimize the low-frequency output ripple for converters operating at constant duty-cycle and CCM. The proposed circuit provides current feedback to the bus capacitor, acting to reduce the output current and bus voltage low-frequency ripple. A dynamic model for the proposed converter in CCM is obtained and used to determine the output current modulation as a function of converter parameters. It is shown that the proposed topology leads to a smaller low-frequency ripple than a conventional counterpart at the same operating point. A 95 W design example and a prototype supplying an LED load of 98.8 V / 960 mA for the proposed circuit and the conventional counterpart are presented. The experimental results show that the proposed arrangement can achieve similar results to the conventional circuit in efficiency, THD, or semiconductor stress, while the obtained output current modulation equals to 8.66 % is 3.5 times lower than that in the conventional circuit at same operating point and component values.

Soft-Switching Bridgeless Buck–Boost PFC Converter Using Single Magnetic Core

In this article, a new bridgeless single-phase buck-boost power factor correction (PFC) converter with one magnetic core is introduced. The proposed converter is designed to operate in discontinuous capacitor voltage mode (DCVM) to achieve low total harmonic distortion (THD) and continuous input current with a simple structure. The DCVM operation gives additional advantages, such as inherent PFC, low turn-off losses, and reduced complexity of the control circuitry. Unlike the buck converter, the proposed converter eliminates the dead angle of input current without adding any extra circuits. Also, by eliminating two input diodes in power flowing path, the efficiency is further improved. Due to achieved almost zero current switching at the turn-on and almost zero voltage switching at the turn-off, the switching losses are eliminated. In this article, theoretical analysis and principal operation of the converter are discussed. An experimental prototype is implemented to verify the performance of the proposed converter. Experimental results are presented for a 120-W prototype at 110-V <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">rms</sub> input and 48-V output.

Manitoba Rectifier—Bridgeless Buck–Boost PFC

This paper presents a new bridgeless buck–boost power factor corrector with the use of the active virtual ground technique, which is named as the Manitoba Rectifier. The proposed topology can convert the grid ac voltage into a wide range of voltage outputs within a single-stage circuit. It is in a bridgeless structure and simple in design. During the operation, an LC filter is generated at the system input, where continuous grid current is guaranteed in a buck–boost characteristic topology. In addition, the filter capacitor helps to clamp the voltage ripple between the grid and the output bus terminal. Both leakage current and common mode noise are kept in a relatively small value. Thus, a single-stage and low common-mode buck–boost converter system is built. The proposed topology is successfully implemented on an 800 W prototype, and the performance is experimentally verified, which shows good agreement with the theoretical findings.

Bridgeless Buck-Boost PFC Rectifier with Positive Output Voltage

A bridgeless buck-boost power-factor-correction (PFC) rectifier with positive output voltage is proposed herein. This PFC rectifier operates in the discontinuous conduction mode (DCM). Owing to the DCM, a good performance on PF is easily achieved as well as no reverse recovery currents being generated from the diodes. By means of output voltage sensing along with the traditional voltage-follower control, a proper control force is created to drive the switches. By doing so, not only the output voltage is stably controlled at a given value, but also the input current tracks the input voltage as tightly as possible. In addition, the accompanying harmonic distortion meets the requirements of the IEC6100-3-2 Class C harmonics standard, and accordingly, the proposed rectifier is suitable for the AC-DC LED driver. Finally, via mathematical deductions and experimental results, the effectiveness of the proposed bridgeless buck-boost PFC rectifier is verified.

A Single-Stage LED Streetlight Driver with Soft-Switching and Interleaved PFC Features

This paper presents a single-stage driver with soft-switching and interleaved power-factor correction (PFC) features suitable for light-emitting diode (LED) energy-saving streetlight applications. The proposed LED streetlight driver integrates an interleaved buck-boost PFC converter with coupled inductors and a half-bridge LLC resonant converter into a single-stage power-conversion circuit with reduced voltage stress on the DC-linked capacitor and power switches, and it is suitable for operating at high utility-line voltages. Furthermore, coupled inductors in the interleaved buck-boost PFC converter are operated in discontinuous-conduction mode (DCM) for accomplishing PFC, and the half-bridge LLC resonant converter features zero-voltage switching (ZVS) to reduce switching losses of power switches, and zero-current switching (ZCS) to decrease conduction losses of power diodes. Operational modes and design considerations for the proposed LED streetlight driver are introduced. Finally, a 144 W (36V/4A)-rated LED prototype driver is successfully developed and implemented for supplying a streetlight module and operating with a utility-line input voltage of 220 V. High power factor, low output-voltage ripple factor, low output-current ripple factor, and high efficiency are achieved in the proposed LED streetlight driver.

A Dimmable Offline LED Driver With OOK-M-FSK Modulation for VLC Applications

This paper proposes a visible light communication (VLC) system consisting of a single-stage buck–boost power factor correction converter operating in the discontinuous conduction mode with dimming capability. Additionally, this paper proposes the on – off M-frequency shift keying modulation for the VLC system. This modulation allows for the transmission of more than a single bit for each switching period without affecting the dimming characteristics of the light-emitting diode luminaire. The design of the whole system is discussed in detail, including both transmitter and receiver modules. A 20-W laboratory prototype was built in order to verify the proposed modulation scheme. The experimental evaluation showed a good performance of the transmitter, which was able to perform simultaneously the desired functions, namely power factor correction, dimming, and data transmission. The receiver also achieved the desired performance with a low bit error rate (BER). The results showed that the proposed system was able to transfer data between emitter and receiver with a bit rate of 1.11 Mb/s at a frequency of up to 375 kHz over a distance of 10 m, and with a BER lower than $10^{-3}$ under the influence of external lighting sources with illuminance levels up to 500 lx.

Double Integrated-Buck Boost Converter versus Double Integrated-Buck Topology for LED Lamps

In this paper a comparative study between two different approaches for LED driving based on the double integrated buck boost and a double integrated Buck converter. It presents a single-stage, single-switch, transformer less ac/dc converter suitable for Led lighting applications. High Brightness Light Emitting Diodes (HB LEDs) can be seriously considered for replacing conventional halogen, incandescent and fluorescent lamps in general illumination including streetlights due to the rapid development in LED technology in recent years. In many offline applications, maintaining a high-power factor and low harmonics are of primary importance. Single stage power factor pre-regulation technology is mainly preferred in cost sensitive applications where power factor regulation is necessary, as adding additional power factor correction controller will surely increase the cost. Here a high-power-factor, long life integrated converter able to supply LED lamps from ac mains is presented. This topology integrates a buck-boost type power-factor correction (PFC) cell with a buck–boost dc/dc converter there by providing the necessary high input power factor and low Total Harmonic Distortion (THD). An isolation transformer increases complexities in the implementation of feedback and control. The proposed topology is non-isolated and hence much simpler in implementation. The main advantage of this converter is that this circuit uses only one controllable switch. The converter is used to provide power factor correction in streetlight application. A Double integrated buck converter finds application in fields of solid-state lighting. Buck Converter is widely used for step down dc-dc conversion when there is no isolation requirement. The narrow duty cycle of the buck converter limits its application for high step-down applications. The double integrated buck converter overcomes its limitation. This converter also provides high power factor and output current regulation. A Double integrated buck converter uses for the offline power supply for LED lighting based on the integration of a buck power factor corrector (PFC) and the tapped buck dc/dc converter having high step-down capability and good output current regulation. Due to the high reliability, the simple structure, and the low component count, the proposed topology effectively results to be very suitable for medium power solid-state lighting applications. From Comparative analysis of two circuits integrated double buck boost converter is found to be more efficient with high power factor and low THD.

Buck-Boost AC-DC LED Driver for Lamp with Visible Light Communication Module

A buck-boost AC-DC light-emitting diode (LED) driver for a lamp with a visible light communication (VLC) module is proposed in this paper. In the proposed LED driver, a buck-boost power factor correction converter is utilized for high power factor and regulated DC voltage. It is designed to be operated in the discontinuous conduction mode (DCM) with a 100 [kHz] switching frequency. To obtain a constant current for the LED light, current feedback control is adopted. For visible light communication (VLC), the VLC module consists of an auxiliary inductor and an auxiliary switch, which is connected to an LED string in parallel. The switching frequency of the LED string is 1 [MHz]. For data transfer and dimming control, variable pulse position modulation (VPPM) is used. The presented theoretical analysis and experimental results are verified on an input 90–130 [Vac] and 10 [W] experimental prototype.

Development of a ZVT-PWM Buck Cascaded Buck–Boost PFC Converter of 2 kW With the Widest Range of Input Voltage

This paper describes the development of a new buck cascaded buck–boost power factor correction (PFC) converter of 2 kW with a soft-switching technique. For its wide range of input voltage, it operates in both buck and boost modes. The parameters are properly selected to endure voltage and current stress in all operating ranges. In addition, the electromagnetic interference (EMI) filter is used to reduce the EMI noise and guarantee continuous input current in buck operation. Moreover, the zero-voltage-transient pulse-width-modulation (ZVT-PWM) method is applied to improve the overall efficiency of the converter. The performance of the proposed PFC converter with the widest range of input voltage is evaluated by the hardware experimental test including harmonics analysis based on the International Electrotechnical Commission standard in all operating ranges. Also, the variations of power factor are theoretically analyzed in both buck and boost modes to determine the widest input range of the proposed PFC converter of 2 kW with an EMI filter. These are strongly required to commercialize it in practice. Finally, the efficiency of proposed PFC converter is compared with that of a conventional buck cascaded buck–boost PFC converter under various conditions.

Analysis and Design of a Single-Stage Isolated AC–DC LED Driver With a Voltage Doubler Rectifier

In order to reduce the cost and volume of small-medium power ac–dc light-emitting diode (LED) lighting systems, single-stage LED drivers are often used to drive LEDs with constant current. In this paper, a single-stage isolated high-power factor ac–dc LED driver is proposed and analyzed in detail, which is composed of a buck–boost power factor correction unit operating in discontinuous conduction mode and an isolated dc/dc unit with a voltage doubler rectifier, and the two units are integrated together by sharing the same power switch. Very high input power factor is achieved since the PFC unit operates with almost fixed duty ratio during half period of the utility line voltage. Since a voltage doubler rectifier is included in the isolated dc/dc unit, magnetic core size of the transformer and voltage stress of the secondary side diodes are reduced remarkably. First, the operating principle and performance of the LED driver are analyzed. Then, the main parameters are quantitatively calculated out in detail. Finally, a comparative analysis is presented and a 120 W experimental prototype with 1 A output current is built according to the calculated parameters and the experimental results are presented to verify the correctness of the theoretical analysis and parameter design.

A Single-Stage High-Power-Factor Light-Emitting Diode (LED) Driver with Coupled Inductors for Streetlight Applications

This paper presents and implements a single-stage high-power-factor light-emitting diode (LED) driver with coupled inductors, suitable for streetlight applications. The presented LED driver integrates an interleaved buck-boost power factor correction (PFC) converter with coupled inductors and a half-bridge-type series-resonant converter cascaded with a full-bridge rectifier into a single-stage power conversion circuit. Coupled inductors inside the interleaved buck-boost PFC converter sub-circuit are designed to operate in discontinuous conduction mode (DCM) for achieving input-current shaping, and the half-bridge-type series resonant converter cascaded with a full-bridge rectifier is designed for obtaining zero-voltage switching (ZVS) on two power switches to reduce their switching losses. Analysis of operational modes and design equations for the presented LED driver are described and included. In addition, the presented driver features a high power factor, low total harmonic distortion (THD) of input current, and soft switching. Finally, a prototype driver is developed and implemented to supply a 165-W-rated LED streetlight module with utility-line input voltages ranging from 210 to 230 V. Experimental results demonstrate that high power factor (&gt;0.99), low utility-line current THD (&lt;7%), low-output voltage ripples (&lt;1%), low-output current ripples (&lt;10%), and high circuit efficiency (&gt;90%) are obtained in the presented single-stage driver for LED streetlight applications.

Single‐stage electrolytic capacitor less non‐inverting buck‐boost PFC based AC–DC ripple free LED driver

This study proposes electrolytic capacitor (EC) less power factor correction (PFC) light emitting diode (LED) driver with reduced current ripple. Generally PFC LED drivers need massive ECs to diminish output current ripple. The life-span of LED driver significantly reduces due to short life-span of ECs, and hence demands for EC-less LED drivers. The proposed LED driver is composed of non-inverting buck-boost PFC converter and bi-directional converter (BDC) for ripple current cancellation which replace the short-life ECs with long-life film capacitors. The PFC converter is designed with discontinuous conduction mode in order to ensure unity power factor operation. The role of BDC is to absorb second harmonic ac ripple current of PFC converter and allow the dc current to LED load. In addition, the desired BDC output voltage ( v cbc ) is higher than the PFC output voltage ( V LED ) irrespective of ac source voltage, hence, simplifies the control complexity. Theoretical analysis and predictions of the system have been validated using MATLAB/Simulink simulation, and experimentally validated with a prototype of 7 W. The results evident that PFC integrated BDC provide reduced ripple current with film capacitor as compared with EC counterpart and hence increase the life-span of LED driver.

A Novel Control for a Cascaded Buck–Boost PFC Converter Operating in Discontinuous Capacitor Voltage Mode

This paper presents a new dual-switch control structure for an ac/dc noninverting cascaded buck–boost power factor correction converter. The proposed converter operates at a discontinuous capacitor voltage mode providing an inherent high-power factor and a zero voltage turn-off switching. Additionally, the proposed control structure enables for a nondistorted sinusoidal current for a wide range of output voltage levels. Unlike the conventional methods, a mode detector is not required and consequently there is no hard transition between buck and boost modes. Although both converter switches are controlled, only one feedback control loop is required to obtain the desired power flow at a unity power factor. The principle of operation, theoretical analysis, simulation, and experimental results of a 1.6-kW prototype grid-connected converter are presented. The results confirmed the validity of the proposed system under various operating conditions.

Single-Inductor Dual-Output Buck–Boost Power Factor Correction Converter

A single-inductor dual-output (SIDO) buck–boost power factor correction (PFC) converter operating in critical conduction mode is proposed in this paper. By multiplexing a single inductor, each output of the SIDO buck–boost converter can be regulated independently. Compared with a conventional two-stage multiple-output converter, the SIDO buck–boost PFC converter benefits from significant overall cost saving, small size, and light weight. Moreover, the efficiency of the SIDO buck–boost PFC converter can be improved due to single-stage power conversion. The control strategy and characteristics of the proposed converter are analyzed. The efficiency, power factor, total harmonic distortion, and output accuracy are verified using the experimental results.