Bond Breaking Energy Research Articles

Influence of temperature and crack-tip speed on crack propagation in elastic solids.

I study the influence of temperature and the crack-tip velocity of bond breaking at the crack tip in rubber-like materials. Bond breaking is considered as a stress-aided thermally activated process and results in an effective crack propagation energy, which increases strongly with decreasing temperature or increasing crack-tip speed. This effect is particularly important for adhesive (interfacial) crack propagation but less important for cohesive (bulk) crack propagation owing to the much larger bond-breaking energies in the latter case. For adhesive cracks, the theory results are consistent with adhesion measurements for silicone rubber polydimethylsiloxane (PDMS) in contact with silica glass surfaces. For cohesive cracks, the theory agrees well with experimental results PDMS films chemically bound to silanized glass.

Development of 225Ac-doped biocompatible nanoparticles for targeted alpha therapy

Targeted alpha therapy (TAT) relies on chemical affinity or active targeting using radioimmunoconjugates as strategies to deliver α-emitting radionuclides to cancerous tissue. These strategies can be affected by transmetalation of the parent radionuclide by competing ions in vivo and the bond-breaking recoil energy of decay daughters. The retention of α-emitting radionuclides and the dose delivered to cancer cells are influenced by these processes. Encapsulating α-emitting radionuclides within nanoparticles can help overcome many of these challenges. Poly(lactic-co-glycolic acid) (PLGA) nanoparticles are a biodegradable and biocompatible delivery platform that has been used for drug delivery. In this study, PLGA nanoparticles are utilized for encapsulation and retention of actinium-225 ([225Ac]Ac3+). Encapsulation of [225Ac]Ac3+ within PLGA nanoparticles (Zave = 155.3 nm) was achieved by adapting a double-emulsion solvent evaporation method. The encapsulation efficiency was affected by both the solvent conditions and the chelation of [225Ac]Ac3+. Chelation of [225Ac]Ac3+ to a lipophilic 2,9-bis-lactam-1,10-phenanthroline ligand ([225Ac]AcBLPhen) significantly decreased its release (< 2%) and that of its decay daughters (< 50%) from PLGA nanoparticles. PLGA nanoparticles encapsulating [225Ac]AcBLPhen significantly increased the delivery of [225Ac]Ac3+ to murine (E0771) and human (MCF-7 and MDA-MB-231) breast cancer cells with a concomitant increase in cell death over free [225Ac]Ac3+ in solution. These results demonstrate that PLGA nanoparticles have potential as radionuclide delivery platforms for TAT to advance precision radiotherapy for cancer. In addition, this technology offers an alternative use for ligands with poor aqueous solubility, low stability, or low affinity, allowing them to be repurposed for TAT by encapsulation within PLGA nanoparticles.Graphical

Towards highly-selective H2O2 photosynthesis: In-plane highly ordered carbon nitride nanorods with Ba atoms implantation

Graphitic carbon nitride (g-C3N4) shows great potential in photocatalytic H2O2 production. However, challenges arise from its low in-plane crystallinity and selectivity in two-electron oxygen reduction reaction (2e−-ORR), greatly limiting its H2O2 photosynthesis efficiency. Herein, we develop an ingenious strategy to simultaneously increase the in-plane crystallinity and induce the highly-selective 2e−-ORR by rationally designing barium (Ba) atom-implanted in-plane highly ordered g-C3N4 nanorods. The approach involves controllable synthesis of in-plane high crystallinity g-C3N4 nanorods with Ba implantation (BI-CN) using a BaCl2-mediated in-plane polymerization strategy. The unique Ba-N interaction induces the oriented polymerization of 3-s-triazine units to form well-arranged in-plane structures. Experimental and theoretical calculations clarify that the implanted Ba atoms function as positive charge centers, resulting in a Pauling-type O2 adsorption configuration. This minimizes O–O bond breaking energy, thus suppressing the four-electron oxygen reduction reaction (4e−-ORR) and facilitating a highly-selective 2e−-ORR pathway for efficient photocatalytic H2O2 production. Consequently, the optimized BI-CN3 photocatalyst exhibits an outstanding H2O2 production rate of as high as 353 μmol L−1 h−1, surpassing the pristine g-C3N4 by 6.1 times. This study concurrently optimizes the in-plane crystallinity and O2 adsorption sites of g-C3N4 photocatalysts for highly-selective H2O2 production, providing innovative insights for designing efficient photocatalysts with diverse applications.

Stable and selective multi-porous nickel nanoparticles catalysts for hydrocracking of dibenzyl ether supported by DFT studies

Preparation of clean fuel from biomass has a crucial significance on the development and utilization of renewable clean energy. In this study, a multi-stage porous mordenite supported nickel nanoparticles catalyst (Nix%/HMOR) was prepared, which showed that its acid content, acidity, porosity, specific surface area and metal dispersion were significantly improved while the crystallization strength was basically the same compared with microporous mordenite. In order to study the conversion mechanism of biomass energy, dibenzyl ether was selected as a typical lignin model compound. Under the condition of Ni10%/HMOR in n-hexane at 160 °C for 2 h under 5 MPa of initial hydrogen pressure, the conversion of dibenzyl ether was 100 % and the selectivity of methyl cyclohexane was 84.4 %, which manifested that Ni10%/HMOR had good activity in the selective hydrocracking process under mild conditions. Furthermore, density functional theory (DFT) was selected to study the activation energies of different reaction sites on dibenzyl ether bridge bonds and the recombination process of free radicals in the reaction process. It comes to a conclusion that the O atom on the C-O bridge bond is easier to be attacked by H*, and the C-O bond of the unsaturated aromatic ring is easier to break. During the recombination of free radicals, the two C-O bond breaking energy barriers of OMD are different, and H free radicals are more likely to attack the O atom in cyclohexane-methanol. It is conducive to the formation of stable compound 1 - (cyclohexylmethyl) − 1-methylcyclohexane and its isomers.

EVALUATION OF THE THERMAL-OXIDATIVE STABILITY OF A HALOGEN-CONTAINING PLASTICIZER-FIRE RETARDANT

The importance of assessing the indicators of thermal-oxidative stability of plasticizers that are part of polymer compositions for ensuring high performance indicators during their processing and operation of finished products is noted. When using brominated organic compounds of the aromatic series, a short burning time of polymer compositions and a significant smoldering time have been established. The use of flame retardants containing a halogen in the aliphatic radical leads to a decrease in the smoldering time and an increase in the duration of combustion due to a decrease in the thermal stability of the material at the stage of decomposition. It is indicated that bromine-containing compounds give the best inhibition effect compared to chlorine-containing compounds due to a decrease in the carbon-bromine bond breaking energy compared to the carbon-chlorine bond energy. The decomposition parameters of the brominated plasticizer-fire retardant have been established. It is shown that the thermal decomposition of the brominated plasticizer occurs in two stages, corresponding to the elimination of bromine from the aliphatic radical in the temperature range 473 K – 573 K and the decomposition of phthalic acid esters in the range 603 K – 623 K. The beginning of intensive decomposition corresponds to 443 K. The maximum of the first stage of decomposition is at the point corresponding to 501 K, the second - 606-623 K. It was noted that the bromine-free plasticizer decomposes intensively, starting from 503 K and reaches the maximum decomposition rate at 611 K. The maximum loss of the bromine-free plasticizer was established at 27%, brominated - 50.9% of the mass of the sample. It has been confirmed that the presence of bromine atoms in the plasticizer adversely affects its thermal stability. The influence of the degree of halogenation of an unsaturated plasticizer on the nature of its thermal-oxidative degradation in the temperature range corresponding to the technological parameters of processing polymeric materials at elevated temperatures of 413-443 K has been studied. It is shown that an increase in the content of bromine in the plasticizer when performing technological operations for the processing of polymer compositions in the specified temperature range and the duration of exposure to elevated temperatures within one hour does not significantly affect the mass fraction of bromine in the plasticizer. A kinetic equation for the reaction of thermal decomposition of a bromine-containing plasticizer-flame retardant of the phthalate type, accompanied by the elimination of hydrogen bromide, is proposed. The activation parameters of the hydrogen bromide evolution reaction were determined for the temperature range of maximum decomposition of a brominated phthalate plasticizer with a bromine content in the range of 5% – 25%. It is shown that the activation energy of hydrogen bromide elimination depends on the bromine content in the plasticizer and decreases by 23% with an increase in the degree of bromination. It is shown that the temperature range of maximum decomposition of the brominated fire retardant plasticizer, corresponding to 473 K – 573 K, allows using it as a secondary plasticizer for polyvinyl chloride without reducing the thermal stability of the base.

Modular Approach to Selected Configuration Interaction in an Arbitrary Spin Basis: Implementation and Comparison of Approaches.

A modular selected configuration interaction (SCI) code has been developed that is based on the existing Monte-Carlo configuration interaction code (MCCI). The modularity allows various selection protocols to be implemented with ease and allows for fair comparison between wave functions built via different criteria. We have initially implemented adaptations of existing SCI theories, which are based on either energy- or coefficient-driven selection schemes. These codes have been implemented not only in the basis of Slater determinants (SDs) but also in the basis of configuration state functions (CSFs) and extended to state-averaged regimes. This allows one to take advantage of the reduced dimensionality of the wave function in the CSF basis and also the guarantee of pure spin states. All SCI methods were found to be able to predict potential energy surfaces to high accuracy, producing compact wave functions, when compared to full configuration interaction (FCI) for a variety of bond-breaking potential energy surfaces. The compactness of the error-controlled adaptive configuration interaction approach, particularly in the CSF basis, was apparent with nonparallelity errors within chemical accuracy while containing as little as 0.02% of the FCI CSF space. The size-to-accuracy was also extended to FCI spaces approaching one billion configurations.

The role of halogens in Au–S bond cleavage for energy-differentiated catalysis at the single-bond limit

The transformation from one compound to another involves the breaking and formation of chemical bonds at the single-bond level, especially during catalytic reactions that are of great significance in broad fields such as energy conversion, environmental science, life science and chemical synthesis. The study of the reaction process at the single-bond limit is the key to understanding the catalytic reaction mechanism and further rationally designing catalysts. Here, we develop a method to monitor the catalytic process from the perspective of the single-bond energy using high-resolution scanning tunneling microscopy single-molecule junctions. Experimental and theoretical studies consistently reveal that the attack of a halogen atom on an Au atom can reduce the breaking energy of Au−S bonds, thereby accelerating the bond cleavage reaction and shortening the plateau length during the single-molecule junction breaking. Furthermore, the distinction in catalytic activity between different halogen atoms can be compared as well. This study establishes the intrinsic relationship among the reaction activation energy, the chemical bond breaking energy and the single-molecule junction breaking process, strengthening our mastery of catalytic reactions towards precise chemistry.

ELECTROCHEMICAL BEHAVIOR OF DIMETHYLSULPHONE ON A PLATINUM ELECTRODE

In this work, we studied the effect of dimethylsulfone concentrations on the rate of anodic oxygen evolution and cathodic hydrogen evolution on a platinum electrode in acidic and alkaline media. By the method of calculating the DFT electron density functional at the level of the B97-3c theory using the Orca 4.2.0 program, the dimethyl sulfone bond breaking energy on the surface of platinum will be preferable through C-S bonds, according to the ion-radical mechanism. It has been confirmed by NMR and Raman spectroscopy that the end products of the anodic oxidation of dimethylsulfone in an acidic medium are methanesulfonic acid and dimethyldisulfone, in an alkaline medium - only dimethyldisulfone; the end products of cathodic reduction of DMSO2 are dimethylpolysulfides. Based on the obtained experimental results, a scheme of the electrocatalytic behavior of dimethylsulfone on a platinum electrode is proposed.

Role of non-covalent interactions in 2,5-di-Me-pyrazine-di-N-oxide - tertiary butyl alcohol - single-walled and multi-walled carbon nanotubes electrocatalytic systems

Oxidation of tert-butyl alcohol (tert-BuOH, Me3COH), a compound with a high C-H bond breaking energy in the absence of precious metals or their oxides as catalysts and using metal-free electrodes, is an inexpensive process and is of interest for practical applications in electrocatalysis and sensors. In this work, electrocatalytic systems 2,5-di-Me-pyrazine-di-N-oxide (Pyr1) - tert-BuOH – single - walled (SWCNT) and multi-walled (MWCNT) carbon nanotube paper electrodes in 0.1 M Bu4NClO4 solution in acetonitrile (MeCN) were studied by the methods of cyclic voltammetry, quantum chemical modeling and electron paramagnetic resonance (EPR) electrolysis. Calculaition of energies of non-covalent interactions between the components of the electrocatalytic system in complexes Me3COH*Me3COH, Me3COH*MeCN, Pyr1*Me3COH and the adsorption energy of Me3COH and complexes of Pyr1*Bu4NClO4, Pyr1*Me3COH, Pyr1*MeCN and Me3COH *Bu4NClO4 on CNTs surface using a cluster model describing the surface of conducting carbon nanotubes (10, 10) was performed. The study made it possible to reveal the regularities characteristic of aromatic-di-N-oxide – CNT electrocatalytic systems and to propose a mechanism of tert-BuOH oxidation in the presence of electrochemically generated radical cation Pyr1. The data will be useful at using CNT electrodes in electrocatalytic processes, as well as aromatic di-N-oxide-CNT catalytic systems in electrocatalysis and sensors.

The Catalytic Effect of Vanadium on Sorption Properties of MgH2-Based Nanocomposites Obtained Using Low Milling Time.

The effects of catalysis using vanadium as an additive (2 and 5 wt.%) in a high-energy ball mill on composite desorption properties were examined. The influence of microstructure on the dehydration temperature and hydrogen desorption kinetics was monitored. Morphological and microstructural studies of the synthesized sample were performed by X-ray diffraction (XRD), laser particle size distribution (PSD), and scanning electron microscopy (SEM) methods, while differential scanning calorimetry (DSC) determined thermal properties. To further access amorph species in the milling blend, the absorption spectra were obtained by FTIR-ATR analysis (Fourier transform infrared spectroscopy attenuated total reflection). The results show lower apparent activation energy (Eapp) and H2 desorption temperature are obtained for milling bland with 5 wt.% added vanadium. The best explanation of hydrogen desorption reaction shows the Avrami-Erofeev model for parameter n = 4. Since the obtained value of apparent activation energy is close to the Mg-H bond-breaking energy, one can conclude that breaking this bond would be the rate-limiting step of the process.

Dissociative electron attachment to gold(I)-based compounds: 4,5-dichloro-1,3-diethyl-imidazolylidene trifluoromethyl gold(I).

With the use of proton-NMR and powder XRD (XRPD) studies, the suitability of specific Au-focused electron beam induced deposition (FEBID) precursors has been investigated with low electron energy, structure, excited states and resonances, structural crystal modifications, flexibility, and vaporization level. 4,5-Dichloro-1,3-diethyl-imidazolylidene trifluoromethyl gold(I) is a compound that is a uniquely designed precursor to meet the needs of focused electron beam-induced deposition at the nanostructure level, which proves its capability in creating high purity structures, and its growing importance in other AuImx and AuClnB (where x and n are the number of radicals, B = CH, CH3, or Br) compounds in the radiation cancer therapy increases the efforts to design more suitable bonds in processes of SEM (scanning electron microscopy) deposition and in gas-phase studies. The investigation performed of its powder shape using the XRPD XPERT3 panalytical diffractometer based on CoKα lines shows changes to its structure with change in temperature, level of vacuum, and light; the sensitivity of this compound makes it highly interesting in particular to the radiation research. Used in FEBID, though its smaller number of C, H, and O atoms has lower levels of C contamination in the structures and on the surface, it replaces these bonds with C-Cl and C-N bonds that have lower bond-breaking energy. However, it still needs an extra purification step in the deposition process, either H2O, O2, or H jets.

Selective dechlorination degradation of chlorobenzenes by dual single-atomic Fe/Ni catalyst with M-N/M-O active sites synergistic

Removal and detoxification of chlorobenzenes have attracted public concern, multiple active sites single-atom Fe and single-atom Ni composite nitrogen-doped graphene (FeSA/CN/NiSA) cathode catalyst supplied generation and adsorption capacity of hydrogen and hydroxyl active species. M-O active sites coupled with M-N improved activity and stability of the catalyst, and decreased bond breaking energy barrier of C-Cl, FeSA/CN/NiSA-NiF cathode showed superior removal performance of chlorinated aromatic hydrocarbons (monochlorobenzene: 98.9%, dichlorobenzene: over 90.4%, trichlorobenzene: over 85.7%) and selectivity. Chlorobenzenes were dechlorinated under low stepwise voltage on the FeSA/CN/NiSA-NiF cathode. The efficiencies of stepwise dechlorination reactions of chlorobenzenes were all above 76%, Faradaic efficiencies were above 71.8%. The FeSA/CN/NiSA-NiF cathode was not sensitive to the molecular structure and has overcome the high energy barrier of chlorobenzenes molecular structure. The electrophilic attack of H*ads formed hyperconjugation bond weakened the possibility of the Cl atom forming a bond with the benzene ring, and was favorable for the Cl position to achieve single-electron transfer dechlorination. The selective stepwise dechlorination degradation of chlorobenzenes by FeSA/CN/NiSA-NiF cathode with multiple active sites demonstrated the advantaged performance of M-O and M-N active sites coupled synergistic in electrochemical reduction and degradation, providing a strategy for product-selective degradation of chlorinated aromatic hydrocarbons.

Mechanistic insights into the adsorption of endocrine disruptors onto polystyrene microplastics in water

Microplastics and endocrine disruptors (EDs) are contaminants of emerging concerns and ubiquitously present in aquatic ecosystems, establishing interactions that still are the subject of investigation due to their implications in the cotransport of pollutants. Then, we conducted mechanistic studies based on state-of-art computational chemistry methods to quantitatively understand the interaction mechanisms whereby polystyrene micro or nanoplastics (PS-MPs) interact with representative classes of EDs in water (Ethynylestradiol, Estradiol, and Bisphenol A). The results showed that PS-MPs increase their charge distribution when forming microparticles in water, giving a permanent dipole that explains their increasing solubility in aqueous conditions. In agreement with experimental assessments, the PS-MPs favorably adsorb EDs with adsorption energies larger than 15 kcal/mol, even with comparable stability to nanostructured materials for adsorption, removal, and/or analysis of pollutants. The adsorption occurs via physisorption without covalent binding, bond breaking, or structural preparation energies, where the molecular structure of EDs can favor inner or outer surface adsorption depending on the molecular structure of the adsorbates. A balanced contribution of dispersion and electrostatic stabilizing effects determines the interaction mechanisms, accounting for a whole contribution of 88–90%. The electrostatic contribution emerges from the favorable alignment of the PS-MPs and EDs dipoles upon interaction due to the mild charge transfer between them in solution. In contrast, the dispersion contribution emerges from electron-electron interactions due to the permanent dipoles in adsorbates and adsorbents. Furthermore, thermochemical analyses clarify the role of temperature and pressure effects on the relative adsorption stability among EDs in aquatic environments. Therefore, modeling the adsorption process contributes to new knowledge on the sorption properties of PS-MPs, providing a mechanistic basis to understand the cotransport of pollutants in water environments and their impacts on environmental pollution.

Pressure-assisted decomposition of tricresyl phosphate on amorphous FeO using hybrid quantum-classical simulations.

The moving components of combustion engines are operated under harsh conditions of high pressures and temperatures. Extreme-pressure anti-wear additives, such as tricresyl phosphate (TCP), are mixed with base oil to prevent wear through the formation of a lubricant film on the substrate. We studied the effect of liquid pressure on the decomposition pathway of TCP in base oil molecules (2,5-dimethylhexane) using hybrid quantum-classical simulations with density functional theory for electrons. At a temperature of 300 K, we found that: (i) bond-breaking barrier energies of both the OC and PO bonds of TCP decrease monotonically as the liquid pressure increases; (ii) the bond-breaking barrier energy of PO is lower than that of OC at pressures of 0 and 2.0GPa, but is higher at a pressure of 5.0GPa; and (iii) the applied pressure significantly lowers the bond-breaking barrier energies of both OC and PO when the PO bond of TCP is directed upward from the substrate. These findings are explained by the inhomogeneous distribution of base oil molecules around TCP and the steric repulsion of the PO bond of TCP. These results indicate that the internal structures of the lubricant films are pressure-dependent.

Antioxidation activity of molecular hydrogen via protoheme catalysis in vivo: an insight from ab initio calculations.

Recently, molecular hydrogen has been found to exhibit antioxidation activity through many clinical experiments, but the mechanism has not been fully understandable at atomic level. In this work, we perform systematic ab initio calculations of protoheme-hydrogen complexes to clarify the antioxidation mechanism of molecular hydrogen. We make molecular modeling of iron-protoporphyrin coordinated by imidazole, FeP(Im), and its hydrogen as well as dihydrogen complexes, together with reactive oxygen/nitrogen species (RONS). We carry out structural optimization and Mulliken charge analysis, revealing the two kinds of bonding characteristics between FeP(Im) and H[Formula: see text]: dihydrogen bonding in the end-on asymmetric configuration and Kubas bonding in the side-on symmetric configuration of H[Formula: see text] molecule. The activation barriers for adsorption and dissociation of H[Formula: see text] on and further desorption of H atom from FeP(Im) are found to be below 2.78 eV at most, which is remarkably lower than the H-H bond breaking energy of 4.64 eV in free H[Formula: see text] molecule. We find that the hydrogen bond dissociation energies of FeP(Im)-H[Formula: see text] and -H complexes are lower than those of RONS-H complexes, indicating the decisive role of protoheme as an effective catalyst in RONS antioxidation by molecular hydrogen in vivo.

Promotion of biomass pyrolytic saccharification and lignin depolymerization via nucleophilic reagents quenching of the carbonium ions

The condensation of lignin under acidic conditions inhibited the subsequent value-added utilization of lignin, and the condensed lignin covered the biomass surface. Here, a method of benzenesulfonic acid pretreatment combined with nucleophilic reagents promoted pyrolytic saccharification and lignin hydrogenation was reported. The anhydrosugar content in the pyrolysis bio-oil increased from 66.91% to 69.00%, 72.88%, and 72.16% via adding methanol, propionaldehyde, 3-hydroxylic-2-naphthoic acid, respectively. The characterization of the biomass surface structure and the calculation of bond lengths indicated that carbonium ions prefer to bind with the added nucleophilic reagent rather than the lignin fragment. Furthermore, the quenching of the carbonium ions preserved the β-O-4 bond, as demonstrated in 2D NMR. In the subsequent hydrogenation reaction, it was found that methanol facilitated the production of lignin monomer. The calculation also revealed that the quenching of the carbonium ions with methanol reduced the bond-breaking energy of the β-O-4 bond.

Reverse Conversion Treatment of Gaseous Sulfur Trioxide Using Metastable Sulfides from Sulfur-Rich Flue Gas.

Sulfur trioxide (SO3) is an unstable pollutant, and its removal from the gas phase of industrial flue gas remains a significant challenge. Herein, we propose a reverse conversion treatment (RCT) strategy to reduce S(VI) in SO3 to S(IV) by combining bench-scale experiments and theoretical studies. We first demonstrated that metastable sulfides can break the S-O bond in SO3, leading to the re-formation of sulfur dioxide (SO2). The RCT performance varied between mono- and binary-metal sulfides, and metastable CuS had a high SO3 conversion efficiency in the temperature range of 200-300 °C. Accordingly, the introduction of selenium (Se) lowered the electronegativity of the CuS host and enhanced its reducibility to SO3. Among the CuSe1-xSx composites, CuSe0.3S0.7 was the optimal RCT material and reached a SO2 yield of 6.25 mmol/g in 120 min. The low-valence state of selenium (Se2-/Se1-) exhibited a higher reduction activity for SO3 than did S2-/S1-; however, excessive Se doping degraded the SO3 conversion owing to the re-oxidation of SO2 by the generated SeO32-. The density functional theory calculations verified the stronger SO3 adsorption performance (Eads = -2.76 eV) and lower S-O bond breaking energy (Ea = 1.34 eV) over CuSe0.3S0.7 compared to those over CuS and CuSe. Thus, CuSe1-xSx can serve as a model material and the RCT strategy can make use of field temperature conditions in nonferrous smelters for SO3 emission control.

Theoretical design of nitrogen-rich cages for energetic materials

Nitrogen-rich ring CxNy molecules, new types of potential energetic molecules, were investigated in the computational study reported here. The energetic properties, detonation performance, and stability of four CxNy cages designed based on the most stable N12 cage were researched comparison with hexaazaisowurtzitane and cubane. Calculations were carried out with density functional theory and Møller–Plesset perturbation theory (MP2) using the basis sets 6-31+G(d,p) and cc-pvdz. The stabilities were explored in two ways: (1) the relative stability of one to another based on their own structural features; (2) the thermal stabilities determined by calculating the corresponding bond-breaking energies. Their comparable performance with hexaazaisowurtzitane and cubane highlights the potential applications of these cages as energetic materials and also supports that replacement of nitrogen atoms in all-nitrogen molecules with carbon atom or by oxygen atoms is a good strategy.

Enabling Selenium‐Rich SexSy Cathodes to Work in Carbonate‐Based Electrolytes

AbstractLithium–sulfur/selenium batteries have attracted broad interest and achieved good performance using ether‐based electrolytes. However, when the ether‐based electrolytes are employed, Li–S/Se battery systems still have several inevitable drawbacks inhibiting their practical applications, such as intermediate product dissolution issues, and a dependency on a high content of electrolyte. Thus, it is urgent to pay attention to the electrochemical properties of SexSy cathodes in carbonate‐based electrolytes, which may avoid the above mentioned problems. In this work, a series of mesoporous carbon/SexSy (CMK‐3/SexSy) composites with covalent Se‐S bonds and different Se/S molar ratios are prepared and their working mechanism in carbonate‐based electrolytes is systematically investigated by combining experimental analysis and theoretical calculations. This work finds that the Se in the CMK‐3/SexSy cathode is beneficial for the transportation of Li+ ions and forms a thin cathode electrolyte interphase (CEI) during the discharge–charge process. Furthermore, S substitution in Se8 molecules can enhance the specific capacity and lower the bond breaking and lithiation energies. The optimal CMK‐3/SexSy cathode delivers outstanding performance with a high reversible capacity of 609 mA h g−1 at 1 A g−1 over 300 cycles.

Study on Pyrolytic Mechanisms of n-Perfluorosilanes Si n F2n+2 (2 ≤ n < 6) and Perfluorocyclosilanes Si n F2n (3 ≤ n ≤ 6).

In this paper, the pyrolytic mechanisms of n-perfluorosilanes SinF2n+2 (2 ≤ n < 6) and perfluorocyclosilanes SinF2n (3 ≤ n ≤ 6) are studied in terms of kinetics and thermodynamics by theoretical calculation, and the pyrolytic reaction paths of SinF2n+2 (2 ≤ n < 6) and SinF2n (3 ≤ n ≤ 6) are obtained, which can be used to guide the experimental preparation research studies and separation operations of SinF2n+2 (2 ≤ n < 6), SinF2n (3 ≤ n ≤ 6), and their intermediate substances. The results of the kinetic analysis show that the pyrolytic mechanisms of SinF2n+2 (2 ≤ n < 6) are as follows: first, the silicon–silicon bond breaking induces the generation of free radicals; then, in the chain transfer, the related free radicals participate in F-abstraction transfer with the molecules; and finally, the free radicals form the molecules, and the chain terminates. The F-abstraction transfer is the easiest process to initiate in the low-order silicon–fluorine substance during the chain transfer while releasing SiF2 at the same time, whereas the generation of double free radicals is the most difficult process. The pyrolytic mechanisms of SinF2n (3 ≤ n ≤ 6) are as follows: first, the α–Si–Si bond breaking induces the generation of double free radicals; then, the α–Si–Si or β–Si–Si bond breaks continually in the chain transfer; and finally, the double free radicals form the molecules, and the chain terminates. SiF2 is most easily formed by breaking during the chain transfer. In the pyrolytic processes of SinF2n+2 (2 ≤ n < 6) and SinF2n (3 ≤ n ≤ 6), the chain initiation of silicon–silicon bond breaking requires the highest bond breaking energy, which is the control step of the pyrolytic reaction. The results of the thermodynamic analysis show that the pyrolytic reactions of SinF2n+2 (2 ≤ n < 6) and SinF2n (3 ≤ n ≤ 6) are endothermic. When SinF2n+2 (2 ≤ n < 6) undergoes a pyrolytic reaction and the temperature is higher, the main pyrolytic products are SiF4 and SiF2. When 600 K < T < 1200 K, the main pyrolytic products of Si4F10 are Si3F8 and SiF2, and when 900 K < T < 1400 K, Si5F12 can also convert to Si3F8 and SiF2. The main pyrolytic products of SinF2n (3 ≤ n ≤ 6) are SiF2. When the temperature is higher, the pyrolytic order of SinF2n (3 ≤ n ≤ 6) is as follows: Si3F6 (ring) < Si4F8 (ring) < Si5F10 (ring) < Si6F12 (ring). However, if the temperature is in the range of 1000 K < T < 1200 K, the pyrolytic order is the opposite.