Binary Phase Shift Keying Data Research Articles

A 55 nm CMOS RF Transmitter Front-End with an Active Mixer and a Class-E Power Amplifier for 433 MHz ISM Band Applications

In order to meet the increasing demands of wireless communication for ISM bands, a 433 MHz transmitter RF front-end is designed using a 55 nm low-power CMOS technology. The circuits consist of an active mixer, a driver amplifier and a class-E power amplifier (PA). A double-balanced Gilbert active mixer is designed to realize binary phase-shift keying (BPSK) modulation. The driver is used to preamplify the modulated RF signals. The class-E PA adopts a parallel four-branch cascode structure to control the output power level. The load network of the PA is implemented through an off-chip circuit, in which a finite DC-feed inductance load network is selected to reduce the power loss. The mixer and driver are designed with a 1.2 V supply voltage, while the PA is operated at a 1.8 V supply voltage. The area of the chip is 0.206 mm × 0.089 mm, and the measured results show that it achieves a maximum output power of 2.7 dBm, with a total power consumption of 6.72 mW. At a drain efficiency (DE) of 34.5%, an S22 less than −10 dB over the frequency ranges from 393.79 MHz to 455.70 MHz can be measured for the PA. With 192 kbps BPSK data modulated at 433 MHz, the measured EVM is about 0.83% rms.

Multimode W-Band and D-Band MIMO Scalable Radar Platform

This article demonstrates the implementation of 80- and 160-GHz four-channel radar sensors employing the modular scalable platform based on a single relaxed 40-GHz local oscillator and cascadable transceiver chips. The first two channels synthesize $2 \times 2$ multiple-input–multiple-output (MIMO) radar at 80 GHz with onboard $8 \times 1$ patch arrays for enhanced angular resolution, whereas the other two channels employ 160-GHz system-on-chip transceivers with integrated wideband 6-dBi micromachined on-chip antennas for enhanced range resolution. Configurable modulators in each transceiver offer ranging, direction-of-arrival (DoA) estimation, velocity/vibrations measurement, and data communication applications. Frequency-modulated continuous wave (FMCW) is demonstrated with 4-/8-GHz sweep bandwidth at 80/160 GHz corresponding to 3.75-/1.875-cm range resolution. Chirp-sequence FMCW is employed to measure the heartbeat rate of a human, and 78 bpm is measured with 0.06-Hz Doppler resolution. Mechanical vibration rate from a loudspeaker is measured using the CW radar technique, whereas phase-modulated continuous wave is employed for distant selective vibrations measurement. Time-division multiplexing MIMO radar is configured at 80 GHz in a multitarget scenario for DoA estimation, and the targets are distinguished with 25° effective angular resolution. Frequency-division multiplexing MIMO radar technique is demonstrated based on $\Delta \Sigma $ -modulation and binary phase shift keying (BPSK) modulators. Furthermore, the 10-Mb/s BPSK data communication link is evaluated at 80 GHz with a 20-dB signal-to-noise ratio at 1 m. The 160-GHz vector modulators offer additional modulations.

A MEMS BPSK to ASK converter

PurposeThe purpose of this paper is to investigate the feasibility of using micro electromechanical systems (MEMS) to convert a binary phase shift keying (BPSK) signal to a simpler amplitude shift keying (ASK) scheme.Design/methodology/approachThe prototype is designed within the SOIMUMPs® fabrication process constraints. The fabrication constraints imposed geometric limitations on what could be tested. These constraints were used to build a mathematical model, which in turn was used to optimize the response using MATLAB®. The optimized design was tested using finite element analysis with CoventorWare®, and finally lab tests on the fabricated device were performed to confirm theoretical predictions.FindingsTheoretical predictions compared well with lab measurements on a prototype device measuring 2.9 mm2. The prototype was tested with a carrier frequency of 174 kHz at a BPSK data rate of 3 kHz and carrier amplitude of 6 V. With these parameters, ASK modulation indices of 0.96 and 0.94 were measured at the two output sensors.Originality/valueThis study provides a MEMS solution for BPSK to ASK conversion. The study also identifies what limits betterment of the modulation index and data rate. Such a device has potential application in wireless sensor network (WSN) nodes that have energy harvesters and sensors that are also built in MEMS. Being a MEMS device, it can facilitate integration in such WSN nodes and, hence, potentially reduce size and costs.

A Novel Phase-Locking-Free Phase Sensitive Amplifier-Based Regenerator

We propose a scheme for phase regeneration of optical binary phase-shift keying (BPSK) data signals based on phase sensitive amplification without active phase locking. A delay interferometer is used to convert a BPSK signal impaired by noise to an amplitude modulated signal followed by cross-phase modulation in a highly nonlinear fiber (HNLF), which transfers the data modulation from the amplitude modulated signal to the phase of a locally generated carrier. By placing the HNLF in a loop, a stable phase relation is maintained relative to a set of counter propagating locally generated phase-locked pumps. As a result, active phase stabilization is avoided. A proof-of-principle experiment is carried out with a dual-pump degenerate phase sensitive amplifier, demonstrating regeneration for a 10-Gb/s non-return-to-zero differential BPSK data signal degraded by a sinusoidal phase-noise tone. Receiver sensitivity improvements of 3.5 dB are achieved at a bit error rate of 10−9. In addition, numerical simulations are performed comparing the idealized regenerator performance in the presence of sinusoidal phase modulation as well as Gaussian phase noise.

Phase Regeneration of a BPSK Data Signal Using a Lithium Niobate Phase Modulator

We propose a scheme for phase regeneration of an optical binary phase shift keying (BPSK) data signal using a Lithium Niobate (LiNbO <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">3</sub> ) phase modulator. The scheme is based on heterodyne detection of the BPSK data signal with a continuous wave local oscillator (CW-LO). Carrier recovery is then achieved in the electrical domain using a ×2 frequency-multiplier and a narrow-band filtering scheme. Subsequently, a superposition of the recovered carrier and the heterodyne detected data signal is used to modulate the CW-LO in a LiNbO3 phase modulator. The result is a parametric mixing process in the optical domain, leading to a phase-regenerated BPSK data signal by the coherent superposition with a phase-inverted copy. The proposed scheme constitutes a compact and stable setup, where active phase-stabilization of the electrical data- and carrier-paths can potentially be avoided. An analytical derivation of the working principle is provided, using Jacobi-Anger expansions to describe the phase-modulation. A proof-of-principle experiment is carried out, demonstrating regeneration of a 10 Gb/s NRZ-BPSK data signal degraded by a 5-GHz sinusoidal phase-noise tone. In the proof-of-principle demonstration, the decorrelated data- and LO-carriers are derived from the same CW source. A preliminary test with separate CW sources for data and LO, but without the required electrical narrow-band carrier filtering, is also included. Finally, numerical simulations of the regenerator performance in the presence of wideband phase- and amplitude-noise are performed.

Silicon photonics-wireless interface ICs for micro-/millimeter-wave fiber-wireless networks

We present two types of Si photonics-wireless interface (PWI) integrated circuits (ICs) realized in standard Si technology. Our PWI ICs convert optical signals into radio-frequency (RF) signals for downlink remote antenna units in fiber-wireless networks. Characterization and modeling of Si avalanche photodetectors (APDs) fabricated in two different Si technologies are carried out and used for PWI IC design. A 5-GHz RF-over-fiber PWI IC composed of APD, preamplifier, and power amplifier (PA) is fabricated in 0.18-μm CMOS technology and its performance is verified by 54-Mb/s wireless local area network data transmission. A 60-GHz baseband-over-fiber PWI IC containing APD, baseband photoreceiver, 60-GHz binary phase-shift keying (BPSK) modulator, and 60-GHz PA is realized in 0.25-μm SiGe BiCMOS technology. Error-free transmission of 1.6-Gb/s BPSK data in 60 GHz with this PWI IC is successfully achieved.

Millimeter-Wave Wireless Communication Using Dual-Wavelength Photonic Signal Generation and Photonic Upconversion

This paper presents the design and experimental analysis of a system architecture for 60-GHz broadband wireless communications. The architecture uses a dual-wavelength photonic signal source based on stimulated Brillouin scattering to generate the millimeter-wave carrier signal through photomixing. Data is encoded onto the optical signals and is upconverted directly to the millimeter-wave carrier through a photonic upconversion process, which does not require electronic upconversion. The data is encoded onto one optical wavelength in a single-sideband fashion, which affords significant dispersion tolerance over long remoting distances compared with standard double-sideband modulation. The prototype architecture was tested at ranges of 2-30 m indoors and 78 m outdoors, demonstrating a building-to-building link. Binary phase-shift keying (BPSK) and quadrature phase-shift keying (QPSK) modulation formats were tested, with BPSK data rates up to 3 Gb/s and QPSK data rates up to 2.64 Gb/s. Good bit-error ratios are demonstrated as a function of received power and range for a fixed transmit power.