Bimodal Research Articles

Research on characteristics and influencing factors of road dust emission in a southern city in China.

One of the primary causes of urban atmospheric particulate matter, which is harmful to human health in addition to affecting air quality and atmospheric visibility, is road dust. This study used online monitoring equipment to examine the characteristics of road dust emissions, the effects of temperature, humidity, and wind speed on road dust, as well as the correlation between road and high-space particulate matter concentrations. A section of a real road in Jinhua City, South China, was chosen for the study. The findings demonstrate that the concentration of road dust particles has a very clear bimodal single-valley distribution throughout the day, peaking between 8:00 and 11:00 and 19:00 and 21:00 and troughing between 14:00 and 16:00. Throughout the year, there is a noticeable seasonal change in the concentration of road dust particles, with the highest concentration in the winter and the lowest in the summer. Simultaneously, it has been discovered that temperature and wind speed have the most effects on particle concentration. The concentration of road dust particles reduces with increasing temperature and wind speed. The particle concentrations of road particles and those from urban environmental monitoring stations have a strong correlation, although the trend in the former is not entirely consistent, and the changes in the former occur approximately 1 h after the changes in the latter.

Full transmission of vectorial waves through 3D multiple-scattering media

A striking prediction from the random matrix theory (RMT) in mesoscopic physics is the existence of “open channels”: waves that use multipath interference to achieve perfect transmission across an opaque disordered medium even in the multiple-scattering regime. Realization of such open channels requires a coherent control of the complete incident wavefront and has only been achieved for scalar waves in two dimensions (2D) so far. Here, we utilize a recently proposed “augmented partial factorization” full-wave simulation method to compute the polarization-resolved scattering matrix from 3D vectorial Maxwell’s equations and demonstrate the existence of open channels in 3D disordered media. We examine the spatial profile of such open channels, demonstrate the existence of a bimodal transmission eigenvalue distribution, and study the effects of incomplete polarization control and finite-area illumination. The simulations provide full access to all spatiotemporal properties of the complex wave transport in 3D disordered systems, filling the gap left by experimental capabilities.

Nonequilibrium relaxation of soft responsive colloids.

Stimuli-responsive macromolecules display large conformational changes during their dynamics, sometimes switching between states. Such a multi-stability is useful for the development of soft functional materials. Here, we introduce a mean-field dynamical density functional theory for a model of responsive colloids to study the nonequilibrium dynamics of a colloidal dispersion in time-dependent external fields, with a focus on the coupling of translational and conformational dynamics during their relaxation. Specifically, we consider soft Gaussian particles with a bimodal size distribution between two confining walls with time-dependent (switching-on and off) external gravitational and osmotic fields. We find a rich relaxation behavior of the systems in excellent agreement with particle-based Brownian dynamics computer simulations. In particular, we find time-asymmetric relaxations of integrated observables (wall pressures, mean size, and liquid center-of-mass) for activation/deactivation of external potentials, respectively, which are tunable by the ratio of translational and conformational diffusion time scales. Our work thus paves the way for studying the nonequilibrium relaxation dynamics of complex soft matter with multiple degrees of freedom and hierarchical relaxations.

Autogenic Formation of Bimodal Grain Size Distributions in Rivers and Its Contribution to Gravel‐Sand Transitions

AbstractRiverbeds often fine downstream, with a gravel‐bedded reach, a relatively abrupt gravel‐sand transition (GST), and a sand‐bedded reach. Underlying this behavior, bed grain size distributions are often bimodal, with a relative paucity (gap) around the range 1–5 mm. There is no general morphodynamic model capable of producing the grain size gap and gravel‐sand transition autogenically from a unimodal sediment supply. Here we use a one‐dimensional morphodynamic model including size‐specific bedload and suspended load transport, to show that bimodality readily evolves autogenically even under unimodal sediment feed. A GST forms when we include a floodplain width that abruptly increases at some point. Upstream of the transition, non‐gap gravel ceases to move and gap sediment is preferentially transported. At the transition, non‐gap sand rapidly deposits from suspension, enhancing gap sediment mobility and diluting its presence on the bed.

Recruitment of the Basket Star Astrospartus mediterraneus (Risso, 1826) (Ophiuroidea, Gorgonocephalidae)

The occurrence and abundance of Astrospartus mediterraneus (Risso, 1826) have significantly increased in the last three decades in several areas of the Mediterranean Sea. In the Tavolara–Punta Coda Cavallo Marine Protected Area (NE Sardinia, Tyrrhenian Sea, Mediterranean Sea), 60 specimens were observed mainly on the granitic shoals of the Tavolara Channel, an area characterized by very intense currents and high sedimentation. The basket stars were mainly found living as epibionts of gorgonians (Eunicella verrucosa, Paramuricea clavata and Leptogorgia sarmentosa) and massive sponges (Spongia officinalis, S. lamella, Sarcotragus foetidus). We also documented 21 small specimens (3–20 mm in diameter of the oral disc) observed in June 2024 between 27 and 52 m depth on E. verrucosa and P. clavata colonies. The bimodal size-frequency distribution of these specimens suggested that, probably, specimens belong to two different reproductive events occurring in spring 2023 and 2024.

Microstructure evolution of a novel low-silicon cast aluminum alloy modified with Mn and Cr during solution treatment

The evolution of eutectic Si, the precipitation behavior of dispersoids and microhardness change of the α-Al matrix in a Mn + Cr modified Al-Si-mg-cu alloy during solution treatment were investigated. The results revealed that the evolution of eutectic Si was divided into four paths during solution treatment: Dissolution, splitting, spheroidization and coarsening. Meanwhile, numerous α-Al(FeMnCr)Si dispersoids were precipitated in the eutectic region and the α-Al dendrite arms after solution treatment for 30 min. Due to differences in precipitation behavior, three different dispersoid precipitation zones were formed in the dendrite arms, including the dispersoid-free zone (DFZ) near the grain boundaries, coarse dispersoid zones (CDZ) located in the dendrite cores, and the remaining fine dispersoid zones (FDZ). The bimodal size distribution of the dispersoids within intradendritic regions were closely related to the micro-segregation of Mn and Cr. The precipitation of coarse grain boundary phases exhausted the Fe solute near the grain boundary, which was mainly responsible for the formation of the DFZ. Moreover, there was a partial coherent interface between the dispersoids and the α-Al matrix. The evolution mechanism of matrix microhardness can be well explained by dispersion strengthening effect

Prediction of Traffic Incident Clearance Duration Using Neural Network for Multimodal Data Distribution

Prediction of Traffic Incident Clearance Duration Using Neural Network for Multimodal Data Distribution

The incidence of atrial fibrillation detected by implantable loop recorders: a comparison between patients with and without embolic stroke of undetermined source.

Stroke is the most debilitating outcome of atrial fibrillation (AF). The use of implantable loop recorders increases the detection of AF episodes among patients with embolic stroke of undetermined source. The significance of device-detected AF, or subclinical AF, is unknown. This study aimed to compare the incidence of AF detected by implantable loop recorder in patients with and without embolic stroke of undetermined source. We retrospectively studied all patients without known AF who were referred to our institution for implantable loop recorder implantation following embolic stroke of undetermined source, syncope, or palpitations from March 2009 to November 2019. The primary endpoint was any detection of AF or atrial flutter by implantable loop recorder. Seven hundred and fifty patients were included and followed up for a mean duration of 731 days (SD 443). An implantable loop recorder was implanted following embolic stroke of undetermined source in 323 and for assessment of syncope, palpitations, or another reason in 427 patients. The incidence of AF was significantly (P < 0.001) higher among patients with embolic stroke of undetermined source compared with the non-embolic stroke of undetermined source group; 48.6% vs. 13.8% (for any duration of AF) and 32.2% vs. 12.4% (for AF lasting ≥30 s) both P < 0.001. Kaplan-Meier analysis showed significantly higher incidence of AF for incremental durations of AF up to >5.5 h, but not >24 h. This was driven by longest AF durations of <6 min and between 5.5 h and 24 h, suggesting a bimodal distribution. In a multivariable Cox regression analysis, embolic stroke of undetermined source independently conferred an almost 5-fold increase in the hazard for any duration of AF. The incidence of AF is significantly higher amongst embolic stroke of undetermined source vs. non-embolic stroke of undetermined source patients monitored constantly by an implantable loop recorder. A high number of embolic stroke of undetermined source survivors have short-duration AF episodes. Further work is needed to determine the optimal treatment strategy of these AF episodes in embolic stroke of undetermined source.

Automatic Parallel Tempering Markov Chain Monte Carlo with Nii-C

Due to the high dimensionality or multimodality that is common in modern astronomy, sampling Bayesian posteriors can be challenging. Several publicly available codes based on different sampling algorithms can solve these complex models, but the execution of the code is not always efficient or fast enough. The article introduces a C language general-purpose code, Nii-C, that implements a framework of automatic parallel tempering Markov Chain Monte Carlo. Automatic in this context means that the parameters that ensure an efficient parallel tempering process can be set by a control system during the inital stages of a sampling process. The autotuned parameters consist of two parts, the temperature ladders of all parallel tempering Markov Chains and the proposal distributions for all model parameters across all parallel tempering chains. In order to reduce dependencies in the compilation process and increase the code’s execution speed, Nii-C code is constructed entirely in the C language and parallelized using the message-passing interface protocol to optimize the efficiency of parallel sampling. These implementations facilitate rapid convergence in the sampling of high-dimensional and multimodal distributions, as well as the expeditious code execution time. The Nii-C code can be used in various research areas to trace complex distributions due to its high sampling efficiency and quick execution speed. This article presents a few applications of the Nii-C code.

Resonance-induced synchronization in coupled phase oscillators with bimodal frequency distribution and periodic coupling

Resonance-induced synchronization in coupled phase oscillators with bimodal frequency distribution and periodic coupling

Insights into metabolic heterogeneity of colorectal cancer gained from fluorescence lifetime imaging.

Heterogeneity of tumor metabolism is an important, but still poorly understood aspect of tumor biology. Present work is focused on the visualization and quantification of cellular metabolic heterogeneity of colorectal cancer using fluorescence lifetime imaging (FLIM) of redox cofactor NAD(P)H. FLIM-microscopy of NAD(P)H was performed in vitro in four cancer cell lines (HT29, HCT116, CaCo2 and CT26), in vivo in the four types of colorectal tumors in mice and ex vivo in patients' tumor samples. The dispersion and bimodality of the decay parameters were evaluated to quantify the intercellular metabolic heterogeneity. Our results demonstrate that patients' colorectal tumors have significantly higher heterogeneity of energy metabolism compared with cultured cells and tumor xenografts, which was displayed as a wider and frequently bimodal distribution of a contribution of a free (glycolytic) fraction of NAD(P)H within a sample. Among patients' tumors, the dispersion was larger in the high-grade and early stage ones, without, however, any association with bimodality. These results indicate that cell-level metabolic heterogeneity assessed from NAD(P)H FLIM has a potential to become a clinical prognostic factor.

Insights into metabolic heterogeneity of colorectal cancer gained from fluorescence lifetime imaging

Heterogeneity of tumor metabolism is an important, but still poorly understood aspect of tumor biology. Present work is focused on the visualization and quantification of cellular metabolic heterogeneity of colorectal cancer using fluorescence lifetime imaging (FLIM) of redox cofactor NAD(P)H. FLIM-microscopy of NAD(P)H was performed in vitro in four cancer cell lines (HT29, HCT116, CaCo2 and CT26), in vivo in the four types of colorectal tumors in mice and ex vivo in patients’ tumor samples. The dispersion and bimodality of the decay parameters were evaluated to quantify the intercellular metabolic heterogeneity. Our results demonstrate that patients’ colorectal tumors have significantly higher heterogeneity of energy metabolism compared with cultured cells and tumor xenografts, which was displayed as a wider and frequently bimodal distribution of a contribution of a free (glycolytic) fraction of NAD(P)H within a sample. Among patients’ tumors, the dispersion was larger in the high-grade and early stage ones, without, however, any association with bimodality. These results indicate that cell-level metabolic heterogeneity assessed from NAD(P)H FLIM has a potential to become a clinical prognostic factor.

Achieving a superior combination of strength and ductility by adjusting heterogeneous structure in a Fe–Mn–Al–Mo–C lightweight steel

A combination of high strength and good ductility was achieved by adjusting heterogeneous structure through varying annealing temperatures ranging from 750 to 900 °C after cold rolling in a Fe–Mn–Al–Mo–C lightweight steel. The microstructure consists of heterogeneous recrystallized, unrecrystallized grains containing nanoscale Mo2C precipitates, and intergranular Mo-enriched carbides. As annealing temperature increases, the fraction of recrystallization, and the average Schmid factor increase, while the average grain sizes and the volume fraction of Mo2C decrease. Annealing at 825 °C forms a desirable heterogeneous structure characterized by a normal bimodal grain distribution and diffuse precipitation of intragranular Mo2C particles. Tensile test results indicated that higher annealing temperatures decrease strength but enhance ductility. However, the yield strength of the 825 °C annealed sample only slightly decreases compared to the 800 °C annealed sample owing to the synergistic contributions of various strengthening mechanisms, including grain boundary, solid solution, precipitation, and heterogeneous deformation-induced strengthening. Furthermore, its ductility significantly improves, approaching that of the 850 °C annealed sample, facilitated by sustained heterogeneous deformation-induced strengthening effects and significant refinement in grain structure. The high strain hardening rate of the C825 sample is attributed to dynamic slip band refinement and local stress adjustments during later deformation stages. The heterogeneous grain structure induces a strong HDI strengthening effect due to uneven deformation, which also contributes to the high strain hardening rate. These findings highlight the potential of Fe–26Mn–8Al-1.2C–3Mo lightweight steel for applications requiring a balance of strength and ductility.

Lipid composition and algaenan structure of Botryococcus braunii race L revealed by sequential stepwise pyrolysis

The dried biomass and isolated algaenan of Botryococcus braunii (B. braunii) race L were analyzed using sequential stepwise pyrolysis at 50 °C intervals from 310 °C to 610 °C to investigate algaenan structure. Initial pyrolysis at 310 °C primarily produced free lipids mirroring the extracted products. At 360 °C, distinct isomers of lycopadiene and C40 isoprenoid ketone (i-C40 ketone), derived from the isolated algaenan, indicated the onset of biopolymer degradation. Intermediate pyrolysis (410–510 °C) yielded various isomers of lycopadiene and i-C40 ketone, along with minor short-chain isoprenoids. The consistent formation of C40 isoprenoid isomers up to 460 °C, followed by a decrease at 510 °C, suggested their presence in the algaenan. At 560 °C, high-temperature pyrolysis showed a bimodal distribution of C8 – C32n-alkane/n-alkene doublets, with a reduction in isoprenoids. This shift from isoprenoids to alkyl groups during pyrolysis reflects the diverse thermal stabilities of algaenan moieties. The consistent distributions of lycopadienes and i-C40 ketones during intermediate pyrolysis stages suggested they both present as side chain. The sustaining 9:1 ratio of lycopadienes to i-C40 ketones during intermediate pyrolysis suggests these components are linked to the main chain via ester groups, with a constant ratio of 9:1 in side chains. Aliphatic polyaldehyde, more resistant to be fractured, with a long linear chain serves as the main chain, capable of fragmentation to produce n-alkanes/n-alkenes. Functional group and alkyl moiety identifications were confirmed by FT-IR and NMR spectra. The results demonstrate that sequential stepwise pyrolysis provides detailed chromatographic profiles and transformation data, proving invaluable for understanding algaenan structures in modern microalgae and offers enhanced insights into functional groups and algaenan composition.

Strong and ductile low carbon low alloy steels with multiphase bimodal microstructure

Restrained by the strength-ductility tradeoff, it is still challenging to develop advanced high-strength low carbon low alloy (LCLA) steels with superior strength-ductility combinations and cost-effectiveness to satisfy industry demands. In this study, an innovative 2-cyclic quenching and partitioning (Q&P) heat treatment was developed to produce a novel LCLA steel with the optimized microstructure, in which a bimodal grain size distribution across various constituent phases was achieved. Tensile test results show that the 2-cyclic Q&P LCLA steel exhibits excellent mechanical properties with a uniform elongation, close to 18 %, nearly triple that of conventional Q&P LCLA steel while maintaining a tensile strength above 1 GPa. To reveal the underlying mechanisms of such exceptional strength-elongation synergy, the detailed deformation behaviors of the developed LCLA steel were characterized while the evolution of hetero-deformation-induced (HDI) stress and effective stress was investigated from the perspective of the dislocation model. It is indicated that, with increasing strain, the heterogeneous structures promote strong strain partitioning which leads to extensive geometrically necessary dislocations (GNDs) pile-ups at hetero-interface and persistently strong HDI strengthening effect, and produce the coordinated deformation among constituent phases to realize dislocation forest strengthening, collectively contributing to the enhanced work hardening capacity and hence overcoming the strength-ductility tradeoff. This study provides a new processing strategy for developing strong and ductile LCLA steels.

Influence of Particle Size and Content of Agglomerated Polybutadiene on Mechanical and Rheological Properties of Acrylonitrile-Butadiene-Styrene Terpolymer

The particle size of polybutadiene (PB) particles can be effectively controlled through polymer agglomeration. However, up to now, the impact of the particle size and concentration of agglomerated PB on the mechanical properties and rheological behavior of ABS terpolymer remains unclear. Our research described here studied the effect of the particle size and content of agglomerated PB on the mechanical and rheological properties of ABS. It was found that the impact strength of ABS with a bimodal size distribution of PB (67/452 nm) exceeded that of ABS with a unimodal PB size distribution within the PB content range studied. Furthermore, the impact strength of the ABS containing 319 nm PB above the brittle-toughness transition point was greater than that of other ABS containing unimodal PB at the same PB content. For ABS with a unimodal PB distribution, the PB contents of ABS containing 220, 319, and 415 nm PB at the brittle ductile transition point were 14%, 12%, and 16%, respectively. The tensile strength and melting index of the ABS containing different particle sizes of agglomerated PB decreased linearly with the increase of PB content. Rheological tests showed the viscosity and dynamic viscoelastic properties of the ABS blends. All ABS exhibited shear-thinning behavior, and the addition of PB content resulted in more elastic than viscous behavior in the ABS blends. At the same angular frequency (ω), higher PB content corresponded to greater complex viscosity in the ABS blends. In addition, as the PB content in ABS was increased, it exhibited more solid-like behavior. This study, we suggest, provides a good insight into the effect of agglomerated PB on the ABS/PB blend properties and explores practical applications for the polymer agglomeration of polybutadiene latex (PBL).

Does seasonal flowering and fruiting patterns of cacao only depend on climatic factors? The case study of mixed genotype populations in Côte d'Ivoire

Theobroma cacao, a tropical cauliflorous fruit tree, typically produces flowers and fruits twice a year and exhibits alternate harvesting patterns over consecutive six-monthly seasons in regions with bi-modal rainfall distribution, such as Côte d'Ivoire. This study investigated seasonal variations in flowering and fruiting among trees in populations of mixed cacao genotypes. The intensities of crown and trunk flowering and pod production were monitored for eight consecutive six-monthly seasons on 114 adult cacao trees grown from seedlings. We investigated distributions of seasonal flowering and fruiting values, relationships between flowering and pod production, and the effects of seasonal cumulative rainfall. The patterns of seasonal flowering and fruiting series were analyzed using two descriptors: the first distinguishing between regular and variable patterns, and the second analyzing the structure of such variability, classifying it as either irregular or alternating. Despite being subjected to similar climate and agronomic management, individual trees exhibited highly variable flowering and fruiting behaviors within each season, as well as variable patterns of flowering and fruiting across seasons. Seasonal alternate fruiting on a population scale masked highly variable patterns among trees, and only 19 % of the trees exhibited marked alternate fruiting patterns. Variations in pod production on a tree scale were mainly related to variations in trunk flowering. Endogenous factors seemed to control seasonal variations in flowering and fruiting, even though exogenous factors, both climatic and agronomic, could structure flowering and fruiting patterns at the orchard scale.

Effect of reinforcement particle size on the corrosion and mechanical properties of spark plasma sintered aluminium matrix composites.

In this study, the effects of different sizes of reinforcing particles on the corrosion behaviour and mechanical properties of aluminium (Al)-based composites produced by spark plasma sintering (SPS) are analysed. In the study, the effects of SPS parameters, including electrical power, applied pressure and sintering temperature, on the consolidation process and microstructure evolution of the composite are closely investigated. The results reveal a nuanced relationship between the sintering conditions and the properties of the particles, which in turn determine the sintering dynamics and the formation of the microstructural features. The evaluation of mechanical properties indicates a remarkable influence of particle size distribution on the hardness of the composites, showing an initial improvement with the introduction of nanoparticles, followed by a slight decrease as the balance between nano- and micron-sized Al2O3 particles shifts. A scanning electron microscopy (SEM) study demonstrates the influence of particle dimensions on the change of grain boundaries and the spatial arrangement of the composite matrix. Electrochemical experiments in a 0.1M NaCl solution show a consistent corrosion potential (Ecorr) across all samples, while the current densities associated with corrosion (icorr) show considerable variation. The presence of nano-sized Al2O3 particles was found to increase corrosion resistance, in contrast to the detrimental effects observed with larger microparticles. In particular, composites with a bimodal distribution of particle sizes showed a 3.5-fold increase in corrosion resistance compared to pure Al. The specific Al-2n8mAl2O3 composite that exhibited active electrochemical properties at elevated potentials without a defined passivation range emphasises the significant role of particle size. This study draws attention to bimodal microstructures as a promising route to achieving uniformity and improved corrosion resistance in Al matrix composites, while pointing to the need for further research to fully elucidate the operative mechanisms.

Prevalence and genotype distribution of human papillomavirus infection among 66000 women from 2014 to 2023 in the plateau region of Southwest China

BackgroundPersistent infection with high-risk human papillomavirus (HR-HPV) plays a key role in the onset of cervical cancer. This study was designed to examine the epidemiological trends and genotype distribution of HPV from 2014 to 2023 in the plateau region of Southwest China.MethodsThe findings could offer valuable insights for clinical screening of cervical cancer and the formulation of HPV vaccination policies. This retrospective study analyzed 66,000 women who received HPV-DNA testing at the First People’s Hospital of Qujing, Yunnan, China, between 2014 and 2023. The cohort consisted of 33,512 outpatients, 3,816 inpatients, and 28,672 individuals undergoing health examinations. Cervical cells were collected for DNA extraction, and PCR amplification along with Luminex xMAP technology were used to detect 27 HPV genotypes. The data analysis was conducted using GraphPad Prism and IBM SPSS Statistics 27 software.ResultsThe overall HPV infection rate at the First People’s Hospital of Qujing declined from 24.92% in 2014 to 16.29% in 2023, averaging 16.02%. Specific infection rates were 18.50% among outpatients, 12.97% among inpatients, and 13.53% for health examination attendees. The predominant high-risk HPV genotypes identified were HPV52 (2.61%), HPV16 (2.06%), HPV58 (1.81%), HPV53 (1.55%), and HPV39 (1.09%). Meanwhile, the most frequent low-risk HPV genotypes were HPV6 (1.30%), HPV61 (1.21%), and HPV11 (0.85%). In HPV-positive cases, the distribution of single, double, triple, and quadruple or more infections were 79.90%, 15.17%, 3.59%, and 1.33%, respectively. The proportions of pure LR-HPV, pure HR-HPV, and mixed infections were 22.16%, 67.82%, and 10.02%, respectively. Age-specific analysis revealed a bimodal distribution of HPV infection, with the infection rate rapidly decreasing from 44.02% in the ≤ 19 age group to 19.55% in the 20–29 age group and 13.84% in the 30–39 age group, followed by a gradual increase to 14.64% in the 40–49 age group, 16.65% in the 50–59 age group, and 22.98% in the ≥ 60 age group. The coverage rates of the three available vaccines are all below 50%. The results of this study indicated a declining trend in HPV prevalence in the plateau region of Southwest China over the period from 2014 to 2023, especially in the reduction of genotypes targeted by vaccines.ConclusionThere were significant variations in the genotypes prevalent among different age groups, years, and patient sources within the same region. The underwhelming vaccination rates emphasize the critical need for developing either a multivalent vaccine or a personalized vaccine that targets the HPV genotypes common in the Chinese population. Furthermore, vaccinating adolescents to curb HPV infection and ensuring regular cervical cancer screenings for postmenopausal women are crucial steps.

Larval diet impacts black soldier fly (Diptera: Stratiomyidae) thermal tolerance and preference.

Thermal tolerance and preference are key parameters impacting agricultural production systems. In this study, the impact of larval diet on black soldier fly thermal tolerance and preference across life-stages and sexes was examined. Larvae were fed either a low-protein high-carbohydrate synthetic diet (i.e., P7C35), a high-protein low-carbohydrate synthetic diet (i.e., P35C7), or the Gainesville diet (i.e., C) as a control and reference. Our results demonstrate that the impacts of larval diet on black soldier fly thermal tolerance and preference could be stage and sex specific. The mean heat knockdown temperatures (HKT) ranged between 46.6 and 47.9 °C. Synthetic diets resulted in greater HKT and the difference decreased form larvae (e.g., ∼1 °C) to adults (e.g., ∼0.2 °C). The mean chill-coma recovery time (CCRT) ranged between 8.3 and 21.6 min. Not much differences were detected between diets, but CCRT became longer from larvae to adults. The mean thermal preference ranged between 13.6 and 29.5 °C. Larvae fed synthetic diets preferred much lower temperatures than the control diet. A bimodal distribution was observed for adults regardless of sex. Differences on body mass, lipid, and protein contents were detected among diets; however, more research should be done before any conclusions can be linked to their thermal traits. These findings highlight the importance of considering the ingredients and nutritional makeup of larval diets when optimizing temperature management protocols for mass production of black soldier flies. Conversely, specific diets can be developed to promote survival under extreme rearing temperatures.