Bilayer Planar Heterojunction Research Articles

Conducting Polymers for Optoelectronic Devices and Organic Solar Cells: A Review.

In this review paper, we present a comprehensive summary of the different organic solar cell (OSC) families. Pure and doped conjugated polymers are described. The band structure, electronic properties, and charge separation process in conjugated polymers are briefly described. Various techniques for the preparation of conjugated polymers are presented in detail. The applications of conductive polymers for organic light emitting diodes (OLEDs), organic field effect transistors (OFETs), and organic photovoltaics (OPVs) are explained thoroughly. The architecture of organic polymer solar cells including single layer, bilayer planar heterojunction, and bulk heterojunction (BHJ) are described. Moreover, designing conjugated polymers for photovoltaic applications and optimizations of highest occupied molecular orbital (HOMO)–lowest unoccupied molecular orbital (LUMO) energy levels are discussed. Principles of bulk heterojunction polymer solar cells are addressed. Finally, strategies for band gap tuning and characteristics of solar cell are presented. In this article, several processing parameters such as the choice of solvent(s) for spin casting film, thermal and solvent annealing, solvent additive, and blend composition that affect the nano-morphology of the photoactive layer are reviewed.

Unraveling the Morphology in Solution-Processed Pseudo-Bilayer Planar Heterojunction Organic Solar Cells.

The conventional bulk heterojunction (BHJ) structure is widely used for fabricating high-performance organic solar cells (OSCs) due to the nanometer-scale phase separation of the donor/acceptor component. However, the elaborate control of the BHJ morphology is difficult to carry out because the morphology evolution is such a complicated process. The compatibility requirement of materials in the same solvent restricts the structural diversity of the molecules to some extent. Meanwhile, the nanoscopic interpenetrating donor/acceptor domains reduce their crystallinity. The bilayer planar heterojunction (PHJ), by contrast, possesses complementary advantages that can make it an alternative candidate to achieve device fabrication and produce different vertical stratification in heterojunction films. However, the flat contact area limits the charge separation and transmission efficiency. The sequential solution processed approach was used to facilitate material diffusion in layers. Also, solvent additives were employed to further enhance the diffusion and thus the device performance. Nevertheless, the morphology of the formed pseudo-bilayer planar heterojunction (PPHJ) has not been fully revealed yet. Here, we carefully study the morphology of the nonfullerene-based PPHJ device in three dimensions. High hole mobility of 2.09 × 10-4 cm2 V-1 s-1 and electron mobility of 7.91 × 10-5 cm2 V-1 s-1 were obtained in the solution-processed PPHJ device. Meanwhile, a distinct phase separation size with a vertical rearrangement of donor and acceptor was observed, which enable the pseudo-bilayer devices to be equipped with a comparable spectral response to the BHJ devices. We demonstrate that a unique device architecture (ITO/ZnO/PBDB-T/ITIC/MoO3/Ag) with a power conversion efficiency of 7% can be obtained from a larger molecular weight of PBDB-T without using extra additives. The solution-processed PPHJ films have much in common with the BHJ films. The results proposed that with appropriate molecular design and vertical phase separation optimization, the performance of the solution-processed PPHJ-based OSCs can be further improved.

Small Molecular Donors for Organic Solar Cells Obtained by Simple and Clean Synthesis

A small donor-acceptor molecule is synthesized in a two-step procedure involving reaction of N,N-diphenylhydrazine on 2,5-diformylthiophene and Knoevenagel condensation. Results of UV/Vis absorption spectroscopy and cyclic voltammetry show that replacement of the phenyl ring bridge of a reference compound 2 by an azo group produces a slight red-shift of λmax, an enhancement of the molecular absorption coefficient, and a decrease of the energy level of the frontier orbitals. A preliminary evaluation of the potentialities of compound 1 as donor material in a basic bilayer planar heterojunction cell of 28 mm(2) active area using C60 as acceptor gave a short-circuit current density of 6.32 mA cm(-2) and a power conversion efficiency of 2.07 %.

Small D–π–A Systems with o‐Phenylene‐Bridged Accepting Units as Active Materials for Organic Photovoltaics

Donor-acceptor (D-π-A) systems that combine triarylamine donor blocks and dicyanovinyl (DCV) acceptor groups have been synthesized. Starting from the triphenylamine (TPA)-thiophene-DCV compound (1) as a reference system, various synthetic approaches have been developed for controlling the light-harvesting properties and energy levels of the frontier orbitals in this molecule. Thus, the introduction of methoxy groups onto TPA, the replacement of one phenyl ring of TPA by a thiophene ring, or the extension of the π-conjugating spacer group lead to the modulation of the HOMO level. On the other hand, the fusion of the DCV group onto the vicinal thiophene ring by an ortho-phenylene bridge allows for a specific fine-tuning of the LUMO level. The electronic properties of the molecules were analyzed by using UV/Vis spectroscopy and cyclic voltammetry and the compounds were evaluated as donor materials in basic bilayer planar heterojunction solar cells by using C60 as acceptor material. The relationships between the electronic properties of the donors and the performance of the corresponding photovoltaic devices are discussed. Bilayer planar heterojunction solar cells that used reference compound 1 and C70 afforded power-conversion efficiencies of up to 3.7 %.

Short circuit current improvement in planar heterojunction organic solar cells by multijunction charge transfer

A multijunction structure was applied on an organic photovoltaic (OPV) device for broadening the absorption spectrum and enhancing the power conversion efficiency through charge transfer process. By inserting the tris[4-(2-thienyl)]amine (TTPA) into a boron subphthalocyanine chloride (SubPc)/C60 OPV device, the short circuit current density (Jsc) showed a 47.5% increases from 3.05 to 4.50 mA/cm2 in the bilayer planar heterojunction device, while the open circuit voltage (Voc) remained constant. Based on the single junction (TTPA/SubPc) device and photoluminescence absorption results, we confirmed both TTPA/SubPc and SubPc/C60 junctions are contributing to the exciton dissociation process hence the efficiency enhancement.

Manipulation of the Open-Circuit Voltage of Organic Solar Cells by Desymmetrization of the Structure of Acceptor-Donor-Acceptor Molecules

The synthesis of acceptor–donor–acceptor (A–D–A) molecules based on a septithiophene chain with terminal electron acceptor groups is reported. Using a dicyanovinyl- (DCV) substituted molecule as reference, another symmetrical A–D–A donor containing thiobarbituric (TB) groups is synthesized and these two acceptor groups are combined to produce the unsymmetrical A–D–A′ compound. The electronic properties of the donors are analyzed by cyclic voltammetry and UV-Vis absorption spectroscopy and their photovoltaic properties are characterized on bilayer planar heterojunction cells that include spun-cast donor films and vacuum-deposited C60 as acceptor. Optical and electrochemical data show that replacement of DCV by TB leads to a small increase of the HOMO level and to a larger decrease of the LUMO, which result in a reduced band-gap. The desymmetrized compound presents the lowest oxidation potential in solution but the highest oxidation onset in the solid state, which leads to a significant increase of the open-circuit voltage of the resulting solar cells.