Biaxial Tensile Tests Research Articles

Finite Element Simulation of Opening Angle Response of Porcine Aortas Using Layer Specific GAG Distributions in One and Two Layered Solid Matrices.

Recent studies have identified an effect of glycosaminoglycans (GAG) on residual stresses in the aorta,underscoring the need to better understand their biomechanical roles. Aortic ring models for each of the ascending, arch and descending thoracic regions of the porcine thoracic aorta were created in FEBioStudio, using a framework that incorporates the Donnan osmotic swelling in a porous solid matrix. The distribution of fixed charge densities (FCD) through the thickness of the tissue was prescribed as calculated from experimentally quantified sulfated GAG mural distributions. Material parameters for the solid matrix, modeled using a Holmes-Mow constitutive law, were optimized using data from biaxial tensile tests. In addition to modelling the solid matrix as one layer, two layers were considered to capture the differences between the intima-media and the adventitia, for which various stiffness ratios were explored. As the stiffness of the adventitia with respect to that of the media increased, the simulated opening angle increased. The opening angle also decreased from the ascending to the descending thoracic region in both one- and two-layered solid matrices models. The simulated results were compared against the experimental contribution of GAG to the opening angle, as previously quantified via enzymatic GAG-depletion.When using one layer for the solid matrix, the errors between the simulated opening anglesand the experimental contribution of GAG to the opening anglewere respectively 28%, 15% and 23% in the ascending, arch and descending thoracic regions. When using two layers for the solid matrix, the smallest errors in the ascending and arch regions were 21% and 5% when the intima-media was modelled as 10 times stiffer, and as twice stiffer than the adventitia, respectively, and 23% in the descending thoracic regions when the intima-media and adventitia shared similar mechanical properties. Overall, this study demonstrates that GAG partially contribute to circumferential residual stress, and that GAG swelling is one of several regulators of the opening angle. The minor discrepancies between simulated and experimental opening angles imply that the contribution of GAG extends beyond mere swelling, aligning with previous experimental indications of their interaction with ECM fibers in determining the opening angle.

Characterization and modeling of biaxial plastic anisotropy in metallic sheets

The anisotropic behavior of cold-rolled sheet metals has been extensively studied, typically characterized by uniaxial loading tests in different directions to determine yield strengths and plastic flow (Lankford r-values). However, biaxial principal stress states often focus solely on yield loci in the RD/TD (rolling/transverse) directions, with limited studies on other loading directions. This study analyzes the relationship between the principal stress yield loci and the material principal anisotropic stress directions based on the Hill48 yield function. Biaxial tensile tests are conducted on DP590 high-strength steel using cruciform specimens cut in various directions different from the sheet RD/TD directions. The evolution of the anisotropic yield locus and plastic flow of DP590 under biaxial tensile directions beyond the traditional RD/TD anisotropic directions is revealed. Furthermore, a modified Hill48 model that considers any principal stress direction of loading is proposed, accurately describing the continuous evolution of equi-biaxial tension stress, near-plane strain stress, and plastic flow direction for different principal stress directions of loading. The issues of failing to predict plastic flow under biaxial loadings in the original Hill48 model, and the degraded representation of existing constitutive models when accounting for out-of-plane anisotropy are addressed by decoupling the relationship between anisotropic parameters and stress state. In addition, the proposed calibration strategy of anisotropic parameters, using experimental data from various principal stress directions of loading, effectively captures the anisotropic evolution caused by changes in principal stress directions. Comprehensive evaluation and verification of the plasticity model should consider yield locus for any principal stress directions of loading, and also the normal and shear planes.

Investigation of the microstructural behavior of Al–Mg–Si(X)–Mn aluminum alloys based on biaxial hot tensile tests

This study investigates the microstructural behavior of laboratory-produced Al–Mg–Si(X)–Mn aluminum alloys, focusing on the influence of varying Si content during biaxial hot tensile testing. Alloys with Si contents of 0.7%, 0.9%, and 1.3% were subjected to biaxial deformation at temperatures of 200 °C, 300 °C, and 400 °C. Using digital image correlation analysis, the impact of Si content on microstructural evolution under biaxial tensile loading was analyzed. Force–displacement analysis revealed a consistent inverse relationship between temperature and the maximum force required to initiate strain. At the temperature of 200 °C, the Al–Mg–Si(1.3)–Mn alloy required a maximum force of 1500 N, while at the temperature of 400 °C this force decreased to 900 N. The degree of anisotropy varied, with higher Si alloys exhibiting increased resistance to deformation in the transverse direction. In particular, the Al–Mg–Si(1.3)–Mn alloy showed pronounced strain anisotropy, with large major true strain φ1 values reaching up to 0.32 at 400 °C, compared to 0.26 at 300 °C and 0.2 at 200 °C. Microstructural analysis using electron backscatter diffraction (EBSD) and energy dispersive X-ray spectrometry (EDS) showed minimal changes at low temperatures, while increased dislocation density and grain boundary distortion were observed at elevated temperatures. The β-Mg2Si precipitates, influenced by Si content and temperature, significantly affected the mechanical properties. In the Al–Mg–Si(0.7)–Mn alloy, precipitates were predominantly 1–3 µm in diameter, whereas in the Al–Mg–Si(1.3)–Mn alloy, precipitates grew to 4–8 µm at higher Si content. These findings provide critical insights into the mechanical response and deformation mechanisms of aluminum alloys under biaxial tensile conditions, essential for optimizing material performance in engineering applications.Graphical abstract

Investigation on the biaxial tensile testing method for metal foil using cruciform specimen

The assessment of mechanical properties of metal foil under complicated stress states poses a considerable challenge, requiring the development of new testing methods and the optimization of new specimen geometry. In this research, the biaxial tensile method and specimen shape were designed and optimized by using simulation and experiment. It is determined that the strain measurement area can be suggested as the central area of 0.6 to 0.8 times the arm width. The influence of different parameters on the tensile results of cruciform specimens was comprehensively evaluated by finite element method and multi-factor analysis. The results indicate that the number of slits markedly impacts the stress–strain uniformity and shear stress in the central region, followed by the slit length. The effect of the arm width and the slit width is comparable, more influential than the corner radius. According to the analyzed results and application requirements, a four-axis independently driven biaxial tensile test machine for small scale samples was fabricated. During the biaxial tension, the center point offset of the specimen remains within ±0.01 mm. The displacement and load synchronization errors do not exceed 0.01 mm and 50 N, respectively, facilitating the precise control of four-axis synchronization. Conclusively, cruciform specimens featuring diverse geometric characteristics were designed for industrial pure titanium, 304 stainless steel, and Inconel 718 superalloy with thickness of less than 0.3 mm. The biaxial tensile tests were performed to delineate the yield loci, revealing notable anisotropy and size effect. The validation confirms the suitability of the testing method and optimized cruciform specimens for conducting biaxial tensile mechanical properties testing on metal foils characterized by diverse types and thicknesses.

Layer-specific biomechanical and histological properties of normal and dissected human ascending aortas

Recent studies have attempted to characterize the layer-specific mechanical and microstructural properties of the aortic tissues in either normal or pathological state to understand its structural-mechanical property relationships. However, layer-specific tissue mechanics and compositions of normal and dissected ascending aortas have not been thoroughly compared with a statistical conclusion obtained. Eighteen ascending aortic specimens were harvested from 13 patients with type A aortic dissection and 5 donors without aortic diseases, with each specimen further excised to obtain three tissue samples including an intact wall, an intima-media layer and an adventitia layer. For each tissue sample, biaxial tensile testing was performed to obtain the experimental stress-stretch ratio data, which were further fed into the Fung-type model to quantify the tissue stiffness, and Elastin Van Gieson stain and Masson's trichrome stain were employed to quantify the elastic and collagen fiber densities. Statistical analyses were performed to determine whether any significant differences exist in mechanical properties and compositions between diseased and normal aortic tissues. The tissue stiffness of intima-media samples was significant higher in diseased group than that of normal group in longitudinal direction at the stretch ratio 1.30 (p = 0.0068), while no significant differences were found in the other direction or other tissue types. Even though there was no significant difference in elastic or collagen fiber densities between two groups, the diseased group generally had lower elastic fiber density, but higher collagen fiber density for all three tissue layers. Compared to normal aortic tissues, the elastic fiber density of the intima-media layer in the dissected aortic tissue was lower, while its tissue stiffness was significantly higher, indicating the tissue stiffness of the intima-media layer could be a potential indicator for aortic dissection.

Investigation on Fracture Behavior of Electroslag Welding Joint with High-Performance Steel

This study aimed to investigate fracture behavior of electroslag welding (ESW) joint with 590-N/mm2 class steel using numerical analysis, covering a range of material scales in the structural level. The extended Mohr–Coulomb (EMC) fracture criterion was employed for finite element analysis (FEA). Uniaxial tensile test and three-point bending test were conducted to analyze the fracture behavior from the material scale and calibrate the fracture criterion. The test specimens consisted of the base metal, heat-affected-zone metal, and welding metal obtained from an ESW joint with a 590 N/mm2 class steel. Subsequently, FEA was conducted for a biaxial tensile test to investigate fracture behavior at a structural scale and verify the feasibility and accuracy of the calibrated fracture criterion. The comparison between the results from the FEA and test suggests that the FEA based on the EMC fracture criterion can accurately predict fracture behavior but tends to overestimate the bearing capacity. Thereafter, the effect of axial force on column was quantitatively investigated. The results suggest that the existence of tensile axial force at column decreases the ductility of ESW joint and shifts the fracture locus from the welding metal to heat-affected zone. However, the force has minimal influence on the pop-in load. Finally, the feasibility of applying the current Japanese specifications designated for the 490 N/mm2 class steel for the 590 N/mm2 class steel was examined. The results indicate that the provision can serve as a safe and reliable guideline for the 590 N/mm2 class steel as well.

Yield locus and texture evolution of AA7475-T761 aluminum alloy under planar biaxial loading: An experimental and analytical study

AA7475 aluminum alloy is used as a structural material in aerospace and automobile applications where complex loading conditions are applicable. The material properties under multi-axial loading are recommended for efficient component design. Hence, the mechanical behaviour of AA7475-T761 aluminium alloy was investigated through planar biaxial tensile tests. The yield locus evolution and plastic strain direction were measured at higher plastic strain values (up to 7 %) at various load ratios. The yield loci were constructed and compared with existing yield criteria. Yld2000–2d yield criterion demonstrated accurate predictions with a deviation of approximately 1 %, highlighting its effectiveness in capturing the yield behavior of AA7475. Microstructure analysis using Electron Backscatter Diffraction (EBSD) was conducted to understand the misorientation evolution under the multi-axial loading. Bulk-texture analysis was performed using X-ray diffraction method. Texture analysis revealed that uniaxial deformation favoured the development of Cube and Inverse-Copper textures, while biaxial deformation yielded split Inverse-Goss texture formation. Fractography study shows very different fracture surfaces of biaxial samples compared to uniaxial samples. Overall, this study contributes to a comprehensive understanding of the yield behavior, microstructure, and texture evolution of AA7475-T761 aluminium alloy under different loading conditions at very large strains.

Biaxial tensile behavior of CoCrFeNi high-entropy alloy under dynamic and proportional loadings

The dynamic failure behavior of CoCrFeNi High-Entropy Alloy (HEA) under plane biaxial stress was investigated in detail. The dynamic biaxial tensile tests were conducted using an Electromagnetic Biaxial Split Hopkinson Tensile Bar (EBSHTB) system. For comparison, the quasi-static uniaxial and biaxial tensile tests, as well as dynamic uniaxial tensile tests, were performed respectively. A cruciform specimen suitable for large plastic deformation was designed and employed in the experiments. The Finite Element Method (FEM) verified that the improved cruciform specimen could satisfy the basic requirements. The feasibility of the proposed specimen was further confirmed through loading tests. Finally, the quasi-static and dynamic yield loci of the HEA in the first quadrant of the principal stress space were plotted. The results indicate that the alloy exhibits obvious strain hardening effect and strain rate strengthening effect, the yield locus and plastic work contours can be accurately described by Hill’48 criterion.

Biaxial Tensile Testing of Cruciform Samples to Determine the Impact of Pre-Strain on the Forming Limit Diagram of Aluminum Alloy 5052 through Finite Element Simulation

The present work focuses on the effect of pre-strain on the forming limit curves (FLCs) of aluminium alloy 5052 sheet of 2.5 mm thickness using cruciform samples. To identify the effect of pre-strain on the FLC, the finite element simulations are performed on cruciform samples. The cruciform samples are deformed to a small level of pre-strain in different strain paths. Thereafter, the further deformation under the various strain paths to measure the effect of pre-strain on the forming limits are carried out. Pre-strain in uniaxial, plane strain and biaxial loading conditions are considered in this work. For each case, i.e., uniaxial, plane strain and biaxial conditions two pre-strain conditions are considered. The cruciform samples are carefully thinned in the central region to promote development of large plastic strains there and eventually to neck and fail. The output obtained through simulations are presented in terms of forming limit curves for various strain paths.

Regional differences in stomach stretch during organ filling and their implications on the mechanical stress response

As part of the digestive system, the stomach plays a crucial role in the health and well-being of an organism. It produces acids and performs contractions that initiate the digestive process and begin the break-up of ingested food. Therefore, its mechanical properties are of interest. This study includes a detailed investigation of strains in the porcine stomach wall during passive organ filling. In addition, the observed strains were applied to tissue samples subjected to biaxial tensile tests. The results show inhomogeneous strains during filling, which tend to be higher in the circumferential direction (antrum: 13.2%, corpus: 22.0%, fundus: 67.8%), compared to the longitudinal direction (antrum: 4.8%, corpus: 24.7%, fundus: 50.0%) at a maximum filling of 3500 ml. Consequently, the fundus region experienced the greatest strain. In the biaxial tensile experiments, the corpus region appeared to be the stiffest, reaching nominal stress values above 400 kPa in the circumferential direction, whereas the other regions only reached stress levels of below 50 kPa in both directions for the investigated stretch range. Our findings gain new insight into stomach mechanics and provide valuable data for the development and validation of computational stomach models.

Functional failure criterion based on biaxial tensile testing of steel liners and its application to fragility analysis of nuclear containment under overpressure conditions

To investigate the mechanical behavior of the steel liner under bi-directional tensile loading, 39 cruciform tensile specimens made of P265GH steel liner are examined by biaxial tensile tests with different loading ratios. Based on the strength theory of materials and test results, an anisotropic tearing criterion for the steel liner is established. Subsequently, the proposed tearing criterion is applied to the fragility analysis of the containment under overpressure conditions. Finally, the differences between the proposed and existing tearing criteria are discussed. The results show that the strength of the steel liner under biaxial tensile loading is improved, while the deformation capacity is significantly decreased. The proposed tearing criterion is more consistent with the actual behavior of steel liners under bi-directional tensile loading. When evaluating the probabilistic performance of the containment, it is more practical and safer to predict the functional failure of the containment by using the proposed tearing criterion.

Fracture Behavior of a Unidirectional Carbon Fiber-Reinforced Plastic under Biaxial Tensile Loads.

In order to clarify the fracture behavior of a unidirectional CFRP under proportional loading along the fiber (0°) and fiber vertical (90°) directions, a biaxial tensile test was carried out using a cruciform specimen with two symmetric flat indentations in the thickness direction. Three fracture modes were observed in the specimens after the test. The first mode was a transverse crack (TC), and the second was fiber breakage (FB). The third mode was a mixture mode of TC and FB (TC&FB). According to the measured fracture strains, regardless of the magnitude of the normal strain in the 0° direction, TC and TC&FB modes occurred when the normal strain in the 90° direction, εy, ranged from 0.08% to 1.26% (positive values), and the FB mode occurred when εy ranged from -0.19% to -0.79% (negative values). The TC&FB mode is a unique mode that does not appear as a failure mode under uniaxial tension; it only occurs under biaxial tensile loading. Biaxial tensile tests were also conducted under non-proportional loading. The result showed three fracture modes similarly to the proportional loading case, each of which was also determined by the positive or negative value of εy. Thus, this study reveals that the occurrence of each fracture mode in a unidirectional CFRP is characterized by only one parameter, namely εy.

Energetically stable curve fitting to hyperelastic models based on uniaxial and biaxial tensile tests

Hyperelastic constitutive laws in biomechanics are used to model soft tissues, and material model parameters are often determined by performing curve fitting on data from uniaxial or biaxial tensile tests. The strain energy function of the applied constitutive law must to be energetically stable; however, this condition is not inherently provided by most currently available models. This study provides a procedure to determine stable strain energy functions in a biaxial strain space based on either uniaxial or biaxial tensile tests. Instead of conservative, strain-independent conditions, a stability region is defined in the strain space based on the sample’s tensile tests, thus allowing optimisation within a wider parameter space, resulting in better approximations. An extension of the Levenberg–Marquardt algorithm incorporating user-defined stability constraints is proposed, and the constrained optimisation algorithm is applied to isotropic and anisotropic models. The uniqueness of solutions of the Fung model is also discussed. The material model parameters of stable solutions for soft tissue measurements from various literature sources are determined to demonstrate the proposed procedure. Applying appropriate constraints in the optimisation algorithm resulted in stable and physically permissible constrained solutions for the strain energy function, in contrast to the results of most unconstrained optimisation cases.

Identification of Sheet Metal Constitutive Parameters Using Metamodeling of the Biaxial Tensile Test on a Cruciform Specimen

An identification strategy based on a machine learning approach is proposed to identify the constitutive parameters of metal sheets. The main novelty lies in the use of Gaussian Process Regression with the objective of identifying the constitutive parameters of metal sheets from the biaxial tensile test results on a cruciform specimen. The metamodel is intended to identify the constitutive parameters of the work hardening law and yield criterion. The metamodel used as input data the forces along both arms of the cruciform specimen and the strains measured for a given set of points. The identification strategy was tested for a wide range of virtual materials, and it was concluded that the strategy is able to identify the constitutive parameter with a relative error below to 1%. Afterwards, an uncertainty analysis is conducted by introducing noise to the force and strain measurements. The optimal strategy is able to identify the constitutive parameters with errors inferior to 6% in the description of the hardening, anisotropy coefficients and yield stresses in the presence of noise. The study emphasizes that the main strength of the proposed strategy relies on the judicious selection of critical areas for strain measurement, thereby increasing the accuracy and reliability of the identification process.

Warp-knitted strain sensors: impact of loop parameters on sensing performance under biaxial stretching

This paper explores the sensing performance displayed by warp-knitted strain sensors under biaxial stretching. These sensors were knitted using silver-plated nylon to be interlooped on a tricot warp-knitting machine. Eight types of warp-knitted sensing fabrics with different loop parameters were prepared and, afterward, electro-mechanical tests were conducted on a biaxial tensile testing machine. These specimens offered similar ground structures but differed in conductive yarn configuration in terms of linear density, number of underlapping wales, open/closed loop type, and guide-bar lapping sequence. Experimental results showed that the loop parameters significantly played a fundamental role in determining sensing performance. It is therefore possible to improve the sensing performance of warp-knitted sensors and engineer them by differing the loop parameters based on certain applications.

An improved DIC method for full-field strain measurement in tensile tests on aluminium alloys under hot stamping conditions

Digital image correlation (DIC) outperforms other strain measurement technologies due to its versatility, accuracy, non-contact nature, and capability to capture full-field strains. However, for aluminium alloys like AA6082 under high-temperature and large-deformation conditions, the shiny effects observed in the gauge area degrade the quality of the captured deformation images, leading to failures in the DIC analyses. In this study, the source of the shiny effects was investigated by analysing the evolution of AA6082 specimen surfaces painted with speckle patterns during hot stamping deformation. It was found that the shiny effects were attributed to the exposure of the reflective base material due to paint peeling and cracking. To overcome these problems, the DIC method was improved by developing a novel procedure for generating more effective speckle patterns and utilising a cross-polarisation optical system (XPOL) to mitigate the shiny effects. The improved DIC method was applied to AA6082 in both uniaxial and biaxial tensile tests under diverse hot stamping conditions, along with applications to boron steel for comparison. These improvements significantly reduced the shiny effects and increased the time over which full-field strains can be measured for AA6082, reaching over 96% (up from 75%) of the fracture time in the uniaxial tests and even 100% in the biaxial tests. The improved DIC method enables the full-field strain measurement for aluminium alloys under hot stamping conditions, allowing for the accurate determination of their thermomechanical properties.

A novel mechanical attachment for biaxial tensile test: Application to formability evaluation for DP590 at different temperatures

A novel mechanical attachment for conducting in-plane biaxial tensile test is provided in this paper. In this attachment, the conversion of force from an external actuator into two pairs of orthogonal forces is achieved by specially designed trapezoidal blocks. By using trapezoidal blocks with different inclination angles, biaxial tensile tests of six different tensile ratios can be performed. A heating device is designed for the attachment to conduct thermal biaxial tensile tests. The heating device adopts a combination of the induction heating technology and the conduction heating method. With the developed mechanical attachment and the heating device, the forming limit curves (FLC) of DP590 sheets at ambient temperature, 300 °C, 400 °C and 500 °C are determined using biaxial tensile tests. A classical Nakazima test procedure at ambient temperature is carried out to establish a reference FLC for the material, and the reference FLC is further used to evaluate the results from biaxial tensile tests. Furthermore, an anisotropic GTN model based on Yld2000-3d yield criterion is calibrated by inverse identification procedures and applied to predict the localized necking and fracture for DP590 sheets under biaxial tensions.

Mechanical behavior of PVDF membrane based on the uni-/bi-axial loading experiments

Recently, composite PVDF membranes with good performance have triggered enormous interest because of their great potential application. However, the uncertainty of mechanical properties limits their application. Herein, this paper reveals the elastic modulus properties of the loading angle between warp and tensile direction using the uni-axial tensile test of SH-1050P membrane textile. In addition, the bi-axial tensile test with different loading ratios was implemented. Both uni-axial and bi-axial ductile load-displacement/stress-strain curves are featured. It is the first to establish a relationship between the elastic modulus and the loading angle using a theoretical method based on the assumption that there is no slippage and crease between yarns and matric. Furthermore, simulations with different textile parameters were carried out to verify the theoretical results. The key finding is that the elastic modulus under uni-axial load can be divided into two stages, which are elasticity and plasticity. Both of which are proportional to the sine function applied to two times the loading angle. The Poisson’s ratio of SH-1050P textile can be considered as a fixed value of 0.11. This conclusion can be extended to similar textiles. The outcome of this paper contributes to a deeper understanding of the PVDF memrane’s mechanical behavior and presents a novel insight into its response to different loading conditions.

Identification of thermo-viscoplastic behavior for AA6061 under in-plane biaxial loadings

This work aims to investigate the thermo-visco-plastic behavior of an aluminum alloy (AA6061) sheet metal submitted to in-plane biaxial loadings under warm conditions. Biaxial tensile tests are performed in a temperature range from room temperature to 160 °C, and in a strain rate range from quasi-static to the so-called “intermediate” strain rate (up to few s−1). The specimen shape used in this study has been previously defined and validated by the authors to identify the viscoplastic hardening models of metallic alloys at large strains. A specific device leading to a uniform temperature in the sample is associated with a dynamic biaxial traction bench to carry out the temperature and strain rate dependent characterizations. From these experiments, both the experimental forces measured on each axis of the in-plane biaxial specimen and the principal strains at the center of the specimen are obtained. These experimental data are then used in an inverse analysis loop, based on a finite element model of the biaxial test, to calibrate the parameters of a thermo-viscoplastic strain hardening model by minimizing the difference between the experimental and numerical principal strains at the center point of the specimen. Finally, it is shown that the identified hardening model well predicts the flow stress of AA6061 under different temperatures and strain rates for a strain level of up to 40%.

Effect of the apron in the mechanical characterisation of hyperelastic materials by means of biaxial testing: A new method to improve accuracy

Biological soft tissues and polymers used in biomedical applications (e.g. in the cardiovascular area) are hyperelastic incompressible materials that commonly operate under multi-axial large deformation fields. Their characterisation requires biaxial tensile testing. Due to the typically small sample size, the gripping of the specimens commonly relies on rakes or sutures, where the specimen is punctured at the edges of the gauge area. This approach necessitates of an apron, excess of material around the gauge region.This work analyses the apron influence on the estimated mechanical response of biaxial tests performed by using a rakes gripping system, with the aim of verifying the test accuracy and propose improved solutions.In order to isolate the effect of the apron, avoiding the influence of anisotropy and inhomogeneity typical of most soft tissues, homogeneous and isotropic hyperplastic samples made from a uniform sheet of casted silicone were tested. The stress-strain response of specimens with different apron sizes/shapes was measured experimentally by means of biaxial testing and digital image correlation. Tests were replicated numerically, to interpret the experimental findings.The apron surrounding the gauge area acts as an additional annular constraint which stiffens the system, resulting in a significant overestimate in the stress values. This error can be avoided by introducing specific cuts in the apron.The study quantifies, for the first time, the correlation between the apron size/shape and the experimental stress overestimation, proposing a research protocol which, although identified on homogeneous hyperelastic materials, can be useful in providing more accurate characterisation of both, synthetic polymers and soft tissues.