Benzene, Toluene, Ethylbenzene And Xylene Compounds Research Articles

A comprehensive study on the spatial and temporal variation of BTEX and asbestos in the northwest of Iran: Human risk assessment

Substances like asbestos and other air pollutants, such as BTEX (benzene, toluene, ethylbenzene, and xylene), are hazardous compounds due to their adverse effects on human health. This study aims to investigate the levels, seasonal variations, spatial distribution, potential sources, and associated health risks associated with BTEX compounds and asbestos fibers in the ambient air of Tabriz. Air samples were taken at 16 different locations during the 2020–2021 period. Glass containers with charcoal were used for sample collection, and the BTEX content was determined using the GC-FID method. Phase-contrast microscopy (PCM) analysis was conducted with a low-volume peripheral pump for asbestos fiber sampling. The results showed that the average concentration of ∑BTEX was 37.94 and 27.98 μg/m3 in autumn and spring, respectively. The same parameter was 2.26 and 1.68 f/L for asbestos in the autumn and winter, respectively. The contribution of BTEX to ozone formation potential (OFP) in the research area showed that xylene and toluene were the major contributors to ozone production in different seasons. The risk of exposure to benzene compounds was 24 × 10−4 in children and 55.9 × 10−4 in adults, while the risk of exposure to ethylbenzene was 3.78 × 10−4 in children and 3.25 × 10−4 in adults. The estimated lifetime cancer risk was found to be the highest for benzene, followed by ethylbenzene. The estimated cancer risk for benzene and ethylbenzene exceeded the threshold values set by EPA, which signals a significant carcinogenic risk due to exposure to these substances in the ambient air of Tabriz. According to the EPA guidelines, the low carcinogenicity risk levels are between 10−4 and 10−6. According to the findings for the exposure to asbestos fibers, the maximum values of excess cancer risk (ECR) and estimated lifetime cancer risk (ELCR) were observed in the 16–30 age range across all locations, suggesting increased exposure to asbestos fibers compared to other age groups.

Design and operation of a packed pilot scale distillation column for tire pyrolysis oil: Towards the recovery of value-added raw materials

This work describes the key features involved in the design and operation of a pilot scale distillation column for the recovery of value-added products from tire pyrolysis oil (TPO), as part of the BLACKCYCLE project. The distillation unit was designed using engineering heuristic rules, simulated distillation (SimDist) data and Aspen Hysys ® modeling. The distillation plant consists of a packed column with a nominal throughput of 20 kg/h, and is classified at the fifth technology readiness level (TRL-5). The commissioning and results of long-term experimental campaigns for validation purposes are also presented. In this way, important information is gathered for the design of larger plants. The distillation unit was tested and validated using TPO produced from a pilot scale continuous single-auger pyrolysis plant. A first distillation was performed yielding a heavy fraction (HF-1) with properties suitable for carbon black production, while the light fraction (LF-1) includes the presence of value-added chemicals such as benzene, toluene, ethylbenzene and xylenes (BTEX) and limonene. The LF-1 was also used for a second distillation, producing a stream high in limonene at the bottom (HF-2), and another one high in BTEX compounds at the top (LF-2), which are valuable raw materials for polymer production and petrochemicals, respectively. The key results obtained here are expected to provide an outstanding impetus for the circular economy of complex streams such as end-of-life tires (ELTs) by combining pyrolysis and distillation technologies.

Fly ash-based zeolitic materials of different surface chemistry and texture: Insight into adsorption performance and mechanisms of aqueous BTEX removal

Water contamination caused by anthropogenic, and unforecasted release of BTEX (benzene, toluene, ethylbenzene and xylene) compounds threatens the quality and integrity of aquatic ecosystems. BTEX sorption with novel materials characterized by increased hydrophobicity and stability has been proposed to overcome such contamination. This study aimed to investigate the whole array of hydrothermally synthesized zeolitic materials exhibiting different properties, as well as zeolite/carbon and zeolite/vermiculite composites, to analyse their potential in removing aqueous BTEX. Various parameters and experimental conditions, including the type of volatile organic compounds (VOCs), initial concentration, BTEX coexistence, and increased solution salinity, were studied to verify the applicability of the derived materials. The adsorption capacity of the materials and their governing removal mechanisms were additionally elucidated. The primary removal mechanism involved partitioning on unburned carbon residues, which was observed in zeolite/carbon composites showing the highest BTEX removal efficiency. NaA-zeolite/carbon composite was the most effective in removal of BTEX, with the removal capacity of 15.36 mg/g towards p-xylene. Moreover, the increased salinity of the BTEX solution affects adsorption performance for polar adsorbates, irrespectively of the applied zeolite/carbon composite. Fly-ash (FA) and high-carbon fly-ash (HCFA) were successfully valorised into products with better textural features. These products may effectively tackle organic water pollution caused by VOCs under near-real-life conditions.

Environmental Assessment of Soil and Groundwater Pollution by BTEX Leaching in Valencia Region (Spain)

The impact of hydrocarbon spills in the unsaturated zone is a significant environmental concern, particularly in locations where contamination arises from leaks in underground fuel storage tanks (USTs). This paper presents the outcomes achieved through the utilization of VLEACH, a finite-difference numerical model, to assess the concentrations of organic contaminants in the solid, liquid, and gas phases within the vadose zone. Additionally, it evaluates the mass transfer of pollutants to the aquifer as part of an environmental assessment for the placement of a forthcoming service station. The study encompasses an analysis of 18 scenarios under realistic conditions based on actual field data. These scenarios were constructed, taking into account various factors, including the nature of the leak (one-time or permanent), the depth of the phreatic level, and the soil conditions and properties. The results highlight the potential environmental consequences of a permanent leak as compared to those resulting from a specific accident. The findings further emphasize the substantial influence of soil moisture on transport phenomena within the vadose zone. Variations in soil moisture significantly alter hydraulic conductivity, impact magnitudes, transport velocities, and even the predominant transport mechanism. Consequently, precise delineation of soil moisture becomes a crucial parameter in such simulations. Additionally, it has been observed that each component of BTEX (benzene, toluene, ethylbenzene, and xylene) experiences varying transport velocities through the vadose zone. Benzene, having a greater propensity to concentrate in the liquid and gas phases, exhibits the swiftest movement through the vadose zone. The detection of benzene in aquifers can serve as an indicator of the potential future arrival of the remaining BTEX compounds.

Development of inorganic binder systems to minimise emissions in ferrous foundries

A series of sands with binders based on synthetic resins, which ensure the achievement of some molding sand parameters better than sands with a natural clay binder, do not meet the required expectations related to the impact on the surrounding environment. These include three main classes of sands in which organic binders based on alkyd, phenol-formaldehyde, furan and urea-formaldehyde resins are used. Molding sands subjected to high temperatures of liquid metal generate a number of harmful and even dangerous substances (carcinogenic and/or mutagenic) from the group of benzene, toluene, ethylbenzene and xylenes (BTEX) and polycyclic aromatic hydrocarbons (PAHs). Research carried out as part of the LIFE Green Foundry Project (LIFE17 ENV/FI/000173) concerned the analysis of various types of molding sands in terms of emissions of BTEX and PAHs gases and other compounds (SO2, CO, CO2 and NOx) formed in the process of pouring the mold with liquid metal. In the article, particular attention was paid to the differences in the amount of emitted BTEX and PAHs compounds for two types of sands with organic resins: furan resin (code MF) and phenol-formaldehyde resin (code MA), for which the influence of the regenerate addition on the above values was additionally examined. Three sands with inorganic binders, including 2 binders on water glass base (code MI and code MC) and 1 binder on aluminosilicate base (code MG), and greensand with activated bentonite and coal dust (code MB) were also tested. A comparative analysis of the results evaluated against sand with resin (code MF) containing 85% free furfuryl alcohol, conventionally accepted as a reference sand mix, was performed.It was noted that for a foundry with a uniform (according to the BREF – Best Available Techniques Reference Document for the Smitheries and Foundries Industry) system of molding sands, the obtained Loss on Ignition (LOI) results of the reclaimed fraction compatible with the used molding sand can be used to develop an empirical relationship that allows predicting the approximate content of a given harmful substance (PAHs, BTEX groups) in the molding sand, which makes it easier for the foundry to decide on the need to conduct more advanced tests.The research justifies the opinion about the possibility of reducing the harmful impact of an iron alloy foundry on the surrounding environment by replacing molding sands with organic binders by molding sands with inorganic binders.

Adsorptive removal of BTEX compounds from wastewater using activated carbon derived from macadamia nut shells

In this study, adsorptive removal of benzene, toluene, ethylbenzene and xylenes (BTEX) from synthetic water using activated carbon adsorbent derived from macadamia nut shells was investigated. The surface functional groups of the synthesized adsorbents were assessed by Fourier transform infrared spectra. The specific surface area, pore size and pore volume at 77 K nitrogen adsorption, surface morphology, and the crystalline structure of the adsorbents were determined using Brunauer-Emmett-Teller, scanning electron microscopy and x-ray diffraction, respectively. Batch adsorption mode was used to evaluate the performance of the activated carbon. The stock solutions of synthetic wastewater were prepared by dissolving 100 mg/L of each of the BTEX compound into distilled water in a 250 mL volumetric flask. Effect of initial concentration of BTEX compounds, contact time, and mass of adsorbent on the removal of BTEX compounds from the synthetic wastewater was investigated. The macadamia nut shell–derived activated carbon (MAC) proved to be an effective adsorbent for BTEX compounds, with a large surface area of 405.56 m2/g. The exposure time to reach equilibrium for maximum removal of BTEX was observed to be 20 min. The adsorption capacity of the BTEX compounds by MAC followed the following adsorption order: benzene > toluene > ethylbenzene ˃ xylene.

Fabrication and performance evaluation of tannin iron complex (TA-FeIII/PES) UF membrane in treatment of BTEX wastewater

Oil exploration generates produced water that is characterized as hazardous and toxic waste. Produced water contains a mixture of various pollutants, including monoaromatic hydrocarbons BTEX (benzene, toluene, ethylbenzene, and xylene), compounds that are carcinogenic even in small concentrations. In this study, tannin iron complex (TA-FeIII), blended into polyethersulfone (PES) membrane was evaluated for the treatment of BTEX-containing wastewater. The membranes were fabricated using the non-solvent induced phase separation (NIPS) method and loading of the TA-FeIII complex on the membranes varied from 0–0.9 wt%. The fabricated membranes were characterized using various techniques such as scanning electron microscopy (SEM), water contact angle (WCA), Fourier transform infrared (FTIR) spectroscopy, and atomic force microscopy (AFM) to check the surface morphology, hydrophilicity, surface functionality and surface roughness of the fabricated membranes, respectively. The TA-FeIII modified membranes showed increased pure water flux from 100 (PES 0) to ∼150 (PES 0.9) L/(m2‧h) at 100 kPa. The performance of the fabricated membranes was tested using 70 mg/L synthetic BTEX solution. Overall BTEX rejection > 70% was achieved at increasing TA-FeIII loadings compared to BTEX rejection < 65% for the pure PES membrane. Rejection of the BTEX compounds was mainly through the size exclusion mechanism. These modified TA-FeIII/PES UF membranes proved to be effective in the treatment of BTEX-containing water, and also have the potential to be applied in oily wastewater treatment.

Isolation of Pseudomonas aromaticivorans sp. nov from a hydrocarbon-contaminated groundwater capable of degrading benzene-, toluene-, m- and p-xylene under microaerobic conditions.

Members of the genus Pseudomonas are known to be widespread in hydrocarbon contaminated environments because of their remarkable ability to degrade a variety of petroleum hydrocarbons, including BTEX (benzene, toluene, ethylbenzene and xylene) compounds. During an enrichment investigation which aimed to study microaerobic xylene degradation in a legacy petroleum hydrocarbon-contaminated groundwater, a novel Gram-stain-negative, aerobic, motile and rod-shaped bacterial strain, designated as MAP12T was isolated. It was capable of degrading benzene, toluene, meta- and para- xylene effectively under both aerobic and microaerobic conditions. The 16S rRNA gene sequence analysis revealed that strain MAP12T belongs to the genus Pseudomonas, with the highest 16S rRNA gene similarity to Pseudomonas linyingensis LYBRD3-7T (98.42%), followed by Pseudomonas sagittaria JCM 18195T (98.29%) and Pseudomonas alcaliphila JCM 10630T (98.08%). Phylogenomic tree constructed using a concatenated alignment of 92 core genes indicated that strain MAP12T is distinct from any known Pseudomonas species. The draft genome sequence of strain MAP12T is 4.36 Mb long, and the G+C content of MAP12T genome is 65.8%. Orthologous average nucleotide identity (OrthoANI) and digital DNA–DNA hybridization (dDDH) analyses confirmed that strain MAP12T is distinctly separated from its closest neighbors (OrthoANI < 89 %; dDDH < 36%). Though several members of the genus Pseudomonas are well known for their aerobic BTEX degradation capability, this is the first report of a novel Pseudomonas species capable of degrading xylene under microaerobic conditions. By applying genome-resolved metagenomics, we were able to partially reconstruct the genome of strain MAP12T from metagenomics sequence data and showed that strain MAP12T was an abundant member of the xylene-degrading bacterial community under microaerobic conditions. Strain MAP12T contains ubiquinone 9 (Q9) as the major respiratory quinone and diphosphatidylglycerol, phosphatidylglycerol, phosphatidylethanolamine as major polar lipids. The major cellular fatty acids of strain MAP12T are summed feature 3 (C16:1ω6c and/or C16:1ω7c), C16:0 and summed feature 8 (C18:1ω6c and/or C18:1ω7c). The results of this polyphasic study support that strain MAP12T represents a novel species of the genus Pseudomonas, hence the name of Pseudomonas aromaticivorans sp. nov. is proposed for this strain considering its aromatic hydrocarbon degradation capability. The type strain is MAP12T (=LMG 32466, =NCAIM B.02668).

An assessment of spatial distribution and atmospheric concentrations of ozone, nitrogen dioxide, sulfur dioxide, benzene, toluene, ethylbenzene, and xylenes: ozone formation potential and health risk estimation in Bolu city of Turkey.

Atmospheric pollutants including ozone, nitrogen dioxide, sulfur dioxide, and BTEX (benzene, toluene, ethylbenzene, and xylenes) compounds were evaluated concerning their spatial distribution, temporal variation, and health risk factor. Bolu plateau where sampling was performed has a densely populated city center, semi-rural areas, and forested areas. Additionally, the ozone formation potentials of BTEXs were calculated, and toluene was found to be the most important compound in ground level ozone formation. The spatial distribution of BTEXs and nitrogen dioxide pollution maps showed that their concentrations were higher around the major roads and city center, while rural-forested areas were found to be rich in ozone. BTEXs and nitrogen dioxide were found to have higher atmospheric concentrations in winter. That was mostly related to the source strength and low mixing height during that season. The average toluene to benzene ratios demonstrated that there was a significant influence of traffic emissions in the region. Although there was no significant change in sulfur dioxide concentrations in the summer and winter seasons of 2017, the differences in the spatial distribution showed that seasonal sources such as domestic heating and intensive outdoor barbecue cooking were effective in the atmospheric presence of this pollutant. The lifetime cancer risk through inhalation of benzene was found to be comparable with the limit value (1 × 10-6) recommended by USEPA. On the other hand, hazard ratios for BTEXs were found at an acceptable level for different outdoor environments (villages, roadside, and city center) for both seasons.

Enhancing aromatics and olefins yields in thermo-catalytic pyrolysis of LDPE over zeolites: Role of staged catalysis and acid site density of HZSM-5

The present work deals with the thermo-catalytic pyrolysis of LDPE (low-density polyethylene) in lab-scale one- and two-stage test rigs over HZSM-5 catalysts featuring different acid site densities. In the first part of this work, the influence of catalyst-to-feed ratio and temperature (in conjunction with the acid site density of HZSM-5) on the product distribution was studied with an aim to identify the optimum operating conditions for the enhanced production of aromatics and light olefins. For this purpose, one-stage thermo-catalytic pyrolysis was performed in which catalysts were mixed with LDPE pellets for in-situ catalysis. In the one-stage catalytic pyrolysis, the catalyst sample with the highest acid site density gave the highest concentration of aromatics (ca. 55%) in the pyrolysis oil with a mono-aromatics fraction of over 50% that consisted mainly of BTEX (benzene, toluene, ethylbenzene and xylenes) compounds. The highest C2-C4 olefins concentration (ca. 65%) in the pyrolysis gas was obtained when the sample with the lowest acid site density was used. In the two-stage catalytic pyrolysis (ex-situ catalysis), the concentration of aromatics in the pyrolysis oil reached over 77% with a mono-aromatics fraction of ca. 72% that contained mainly BTEX compounds, when the most acidic catalyst was used. When the catalyst with the lowest number of strong acid sites was employed, the high content of C2-C4 olefins in the pyrolysis gas remained almost independent of the reactor configuration. These findings might provide important new insights for the chemical recycling of plastic wastes.

Measurement of BTEX (benzene, toluene, ethylbenzene and xylene) concentration at gas stations

Background: Fuel stations are one of the major sources of air pollution with volatile organic compounds, especially the four main petrol compounds benzene, toluene, ethylbenzene, and xylene (BTEX). BTEX in gasoline enters the air of gas stations due to high evaporation of gasoline. Therefore, determining the concentration of these compounds in gas stations in crowded and busy cities is one of the important priorities of environmental health, which is doubly important in terms of its negative effects on health. Methods: In this descriptive cross-sectional study, a total of 39 samples were collected from 13 gas stations. Sampling was performed in autumn 2018 in three working shifts (morning, noon, and night). The method NIOSH-1501 (i.e., using charcoal sorbent tubes and SKC pump with a flow rate of 0.2 L/min) was used for sampling the BTEX compounds. The mean difference and correlation of BTEX compounds based on meteorological parameters and the number of nozzles in gas stations were assessed using one-way ANOVA and correlation tests. Results: The mean and standard deviation of benzene, toluene, ethylbenzene, and xylene concentrations in the air of fuel stations were 2.784±1.461, 3.495±1.390, 2.091±0.811, and 1.140±0.419 mg/m3, respectively. The relationship between BTEX compounds and meteorological parameters such as humidity and exposure time is very important. There is a strong correlation between the concentrations of BTEX compounds. The highest correlation was observed between benzene and toluene and the lowest one was observed between benzene and xylene. In this study, no significant relationship was observed between air temperature and concentration of BTEX compounds, but there was a relationship between relative humidity and the concentration of BTEX compounds. Conclusion: The average benzene concentration in the air at the fuel stations was about 5.5 times the standard limit. Authorities should improve fuel quality and reduce its evaporation through engineering measures to overcome the issue.

Determination of BTEX Compounds in Contaminated Water Using the Novel Vacuum-Assisted-Total Vaporization SPME Method and GO-APTES Fiber.

A novel and reliable microextraction technique was used for the fast determination of benzene, toluene, ethylbenzene and xylenes (BTEX) from contaminated water without any extra steps for the preparation or extraction of the aqueous sample. Vacuum-assisted-total vaporization-solid-phase microextraction (SPME) eliminated one of the partitioning steps in conventional headspace SPME and caused an increase in the sensitivity and speed of the method. A home-made graphene oxide/3-aminopropyl-triethoxysilane nanocomposite SPME fiber was synthesized and used as the extraction phase for efficient extraction. Several crucial parameters were optimized, such as the vaporization time and temperature, extraction time and desorption conditions. At the optimum experimental conditions, a linear wide range calibration curve over a wide range of 1-5,000ngmL-1 and a relative standard deviation (n = 6) of 6.6-7.3% were obtained. The result of the determination of BTEX as a human health risk from real samples, using the proposed method, revealed an acceptable agreement with a valid method.

Level of air BTEX in urban, rural and industrial regions of Bandar Abbas, Iran; indoor-outdoor relationships and probabilistic health risk assessment

This study focused on the measurement of BTEX (benzene, toluene, ethylbenzene and xylene) concentrations in the air of various regions and indoor-outdoor environments in Bandar Abbas, Iran. Air samples were taken actively and analyzed by gas chromatography-mass spectrometry (GC-MS) during two one-month periods i.e., Feb 2020 (period I) and Sep/Oct 2020 (period II). The mean air temperature and the levels of all BTEX compounds were higher in period II. The highest total BTEX (t-BTEX) levels (median [min-max]) were found in the urban region (18.00 [5.21–67.24] μg m−3), followed by industrial region (7.00 [2.05–14.76] μg m−3) and rural region (2.81 [ND-7.38] μg m−3). The significant positive correlations between all BTEX compounds and T/B ratio >1 indicated the vehicular traffic as the main source of emission. At 95th percentile probability, the non-cancer risk of t-BTEX in urban region was only less than one order of magnitude below the threshold level of unity (1.91E-01) and the cancer risk of benzene exceeded the recommended level of 1.0E-06 by U.S. EPA in urban (7.69E-06) and industrial (2.97E-06) regions. It was found that the indoor/outdoor ratio of BTEX concentration in beauty salon and hospital was greater than 1. Overall, the current levels of BTEX in the ambient air of study area, especially near urban roadside and in some indoor environments, should not be overlooked and appropriate mitigation actions should be undertaken.

The Seasonality Impact of the BTEX Pollution on the Atmosphere of Arad City, Romania.

Benzene, toluene, and total BTEX (benzene, toluene, ethylbenzene, and xylene) concentrations registered for one year (2016) have been determined every month for one high-density traffic area. The assessment was performed in Arad City, Romania, to evaluate these pollutants and their influence on the inhabitants’ health. The contaminants were sampled using a static sampling method and analyzed by gas chromatography coupled with mass spectrometry. Benzene was the most dominant among the BTEX compounds—the average concentrations ranged from 18.00 ± 1.32 µg m−3 in December to 2.47 ± 0.74 µg m−3 in August. The average toluene concentration over the year was 4.36 ± 2.42 µg m−3 (with a maximum of 9.60 ± 2.39 µg m−3 in November and a minimum of 1.04 ± 0.29 µg m−3 in May). The toluene/benzene ratio (T/B) was around 0.5, indicating substantial contributions from mobile sources (vehicles). The emission and accumulation of different aromatic compounds (especially benzene) could deteriorate the urban air quality. The lifetime cancer risk (LTCR) for benzene was found to be more than 10−5 in winter, including the inhabitants in the “probable cancer risk” category.

Influence of the seasonality and of urban variables in the BTEX and PM2.5 atmospheric levels and risks to human health in a tropical coastal city (Fortaleza, CE, Brazil).

The International Agency for Research on Cancer (IARC) classifies benzene in group 1 (carcinogenic to humans). Particulate matter (PM) has recently also been classified in this category. This was an advance toward prioritizing the monitoring of particles in urban areas. The aim of the present study was to assess levels of PM2.5 and BTEX (benzene, toluene, ethylbenzene, and xylene), the influence of meteorological variables, the planetary boundary layer (PBL), and urban variables as well as risks to human health in the city of Fortaleza, Brazil, in the wet and dry periods. BTEX compounds were sampled using the 1501 method of NIOSH and determined by GC-HS-PID/FID. PM2.5 was monitored using an air sampling pump with a filter holder and determined by the gravimetric method. Average concentrations of BTEX ranged from 1.6 to 45.5μgm-3, with higher values in the wet period, which may be explained by the fact that annual distribution is influenced by meteorological variables and the PBL. PM2.5 levels ranged from 4.12 to 33.0μgm-3 and 4.18 to 86.58μgm-3 in the dry and wet periods, respectively. No seasonal pattern was found for PM2.5, probably due to the influence of meteorological variables, the PBL, and urban variables. Cancer risk ranged from 2.46E-04 to 4.71E-03 and 1.72E-04 to 2.01E-03 for benzene and from 3.07E-06 to 7.04E-05 and 3.08E-06 to 2.85E-05 for PM2.5 in the wet and dry periods, respectively. Cancer risk values for benzene were above the acceptable limit established by the international regulatory agency in both the dry and wet periods. The results obtained of the noncarcinogenic risks for the compounds toluene, ethylbenzene, and xylene were within the limits of acceptability. The findings also showed that the risk related to PM is always greater among smokers than nonsmokers.

Assessment of the improved performance of magnetite-modified vermiculite in the reduction of BTEX and metals, as well as toxicity in petroleum-produced water

Petroleum-produced water has raised considerable environmental concerns due to the large amount of contaminants-containing wastewater, generated during petrol and gas extraction. The present work proposes for the first time the use of vermiculite modified by magnetite (Fe3O4) nanoparticles (VMT-mag) as adsorbent for the extraction of metals and BTEX (benzene, toluene, ethylbenzene, and xylene) pollutants and toxicity reduction. Thermally-treated vermiculite was modified by Fe3O4 nanoparticles of 20 nm, which were strongly adhered to the surface, contributing to the magnetization of the material and adsorption of the metals. A 5 min exposure of wastewater to VMT-mag at 15 mg mL−1 led to the removal of 93 % of dissolved organic carbon, 85 % of BTEX compounds, and a reduction of 30–87% of metals (Ba, Al, Ag, Hg and Pb) at low concentration. An investigation was also conducted regarding the efficiency of VMT-mag in reducing toxicity via toxicity assays using the water flea Daphnia similis (ABTN NBR 12713 protocol); the results showed a reduction of Lethal Concentration at 50 % death (LC50) from 5.80 (v/v) to 13.3 % (v/v), respectively, for the samples before and after treatment. The findings show that the application of the proposed VMT-mag can lead to a significant reduction of toxicity and the removal of BTEX and metals in petroleum-produced water.

Petroleum hydrocarbon pollution in the Niger Delta: human health risk assessment of BTEX in biota

Based on the context of extensive petroleum hydrocarbon pollution in southern Nigeria, the concentrations of benzene, toluene, ethylbenzene and xylene (BTEX) in seafood were determined, and the health risks of these compounds were evaluated. Biota samples (Crayfish, Goby fish, Moonfish, Mudskipper, Mullet, Sardine and Tilapia) were collected from the Bonny Estuary from 2016 to 2018 and analyzed according to US EPA method 5030/8260C to determine the concentrations of BTEX. Risk assessment of BTEX to humans through the dietary route was conducted based on the lifetime cancer risk (LTCR) for benzene and the hazard quotient (HQ) for BTEX. The following BTEX concentration ranges were observed: benzene: < 0.01–0.36 mg/kg; toluene: 0.22–19.85 mg/kg; ethylbenzene: < 0.00–1.54 mg/kg; xylene: < 0.00–7.28 mg/kg. The median LTCR for benzene in children and adults was 0.65 and 0.30, respectively, which are higher than the limit recommended by the World Health Organization. The model showed that the LTCR is reducible by 99.9% and 66.6% if the concentration of benzene is 0.00001 mg/kg, and fresh seafood consumption is reduced to 10.4 g/day. The HQ for all BTEX compounds was greater than 1 (benzene: 1.0 × 104 (child), 4.9 × 103 (adult); toluene: 1.9 × 105 (child), 9.0 × 104 (adult); ethylbenzene: 9.4 × 103 (child), 4.4 × 103 (adult); xylene: 2.5 × 104 (child), 1.2 × 104 (adult)), which signifies a high non-cancer health risk to humans. These results are a reflection of the high level of petroleum hydrocarbon pollution in southern Nigeria and the debilitating human health consequences that could accompany it.

Investigation of seasonal variation and probabilistic risk assessment of BTEX emission in municipal solid waste transfer station

ABSTRACT The municipal solid waste transfer stations (MSWTSs) affects both the environment and human health. The present study aimed to investigatethe Concentrations of BTEX (benzene, toluene, ethylbenzene and xylene) the important group of VOCs, in the ambient air of municipal solid waste transfer station (MSWTS) of Hamadan city and to estimate stochastic cancer and non-cancer risk for inhalation exposure to BTEX compounds by Crystal Ball software. The average produced amount of solid waste in Hamadan in 2109 has been estimated to be over 150,000 tons. The solid waste mostly consisted of a complex mixture containing kitchen/food waste (56.85%), consumed plastics (11.33%), paper (2.88%), glass (1.20%) and other materials (27.74%), which collected from households and commercial areas. The findings revealed that BETX concentration in the ambient air of MSWTS in summer is higher as compared to the spring season. The 95% percentile lifetime cancer risk (LCR) value for benzene was estimated to be 8 × 10−4, which is higher than the recommended standards (10−6). The obtained 95% percentile hazard quotient (HQ) value for xylene was found to be higher than the suggested value of 1. Also, the total cumulative value of the 95th percentile HQs for (toluene, ethylbenzene and xylene) TEX was obtained to be about 3.39, which is higher than the acceptable value of HQ. The results of sensitivity analysis for LCR of benzene and HQs of TEX disclosed that the parameter of pollutants concentration has the highest effect on risk’s variance. According to the values of cancer and non-cancer risk assessment, that were higher than safe levels and the major contribution of pollutant concentration in sensitivity analysis, it is concluded that the implementation and development of technical and engineering control measures must be regarded as an essential target to reduce workers exposure to the pollutants and to decrease the concentration of the pollutant in the ambient air of MSWTS.

Comparing BTEX concentration related to surgical smoke in different operating rooms

The available evidence on the indoor air quality of operating rooms (ORs) in the Low- and Middle-income Countries (LMICs) is very scarce. Moreover, there is no study on the comparing the concentration of indoor air pollutants in different ORs. Therefore, this study aimed to measure and compare the benzene, toluene, ethylbenzene and xylene (BTEX) concentrations in the air of different ORs in hospitals of Sabzevar, Iran. Moreover, carcinogenic and non-carcinogenic risk of exposure to these pollutants were assessed using Monte Carlo simulations technique. This cross-sectional study was based on volatile organic compounds (VOCs) passive sampling of eight ORs including General surgery, Curettage, Eye surgery, Neurosurgery, Orthopedic, Laparoscopic, Cesarean and Ear, nose, throat (ENT) in two monthly campaigns from November 2019 to February 2020. One-way ANOVA and Post-hoc analyses were used to compare the concentration of BTEX compounds in different ORs. The overall mean (standard deviation (SD)) of benzene, toluene, ethylbenzene, xylene and total BTEX concentrations were 10.0 (1.8), 7.2 (1.9), 1.8 (0.6), 0.4 (0.2) and 19.4 (4.1) μg/m3. The Curettage OR had the highest (12.93 μg/m3) and ENT OR had the lowest (7.42 μg/m3) benzene concentrations. The highest concentrations of toluene, ethylbenzene and total BTEX were observed in General surgery OR. The cancer risks of exposure to benzene in all ORs were higher than the acceptable range recommended by Unite State Environmental Protection Agency (USEPA, 1 × 106). However, the hazard quotient (HQ) values for all ORs were at safe level (HQ < 1). Overall, our study suggested that the concentrations of BTEX compounds were significantly difference in different ORs and benzene had a carcinogenic risk for personnel and surgical staff in different ORs.

Monitoring BTEX compounds and asbestos fibers in the ambient air of Tehran, Iran: Seasonal variations, spatial distribution, potential sources, and risk assessment

ABSTRACT The toxic air pollutants such as benzene, toluene, ethylbenzene and xylene (BTEX) as well as asbestos are considered hazardous because of their role in adverse impacts on human health. Accordingly, this research was conducted to evaluate the levels, seasonal variations, spatial mapping, potential sources, and health risk assessment of BTEX compounds as well as asbestos fibres in the ambient air of Tehran. Air samples were collected by the NIOSH1501 method at 15 different sample stations from March 2018 to February 2019. Charcoal glass tube was used to collect samples and BTEX concentration was further determined using GC-FID method. The sampling of asbestos fibres was carried out via a low volume peripheral pump with analysis performed according to the NIOSH 7400 method via phase contrast microscopy (PCM). The findings showed that the mean±SD concentrations of ∑BTEX were 33.44 ± 11.77 and 59.97 ± 33.76 µg/m3 in warm and cold seasons, respectively. It was 1.46 × 10−3 and 2.31 × 10−3 fibre/ml for asbestos in the warm and cold seasons, respectively. The spatial mapping indicated that the maximum levels of both pollutants were observed in sampling sites S1, S11, and S15, which were located close to factories downtown (S1) and heavy traffic roads (S11 and S15). The mean inhalation lifetime cancer risk (LTCR) value for benzene was 1.64 × 10−5, which was higher than US EPA and WHO recommended limits. Further, the excess lifetime cancer risk (ELCR) suggested that the exposure to asbestos fibre in Tehran would cause the risk of developing cancer in 0.5 to 3.53 people per every 1000 individuals. Hence, much suitable managing strategies are required to control the concentration of these pollutants in the ambient air of Tehran.