Benzene, Toluene, Ethylbenzene And Xylene Concentrations Research Articles

BTEX concentration and health risk assessment in automobile workshops

This study focused on the measurement of BTEX (benzene, toluene, ethylbenzene, and xylene) concentrations in the air of indoor and outdoor environments of automobile workshops in Damghan, Iran. Air samples from twenty-five workshops were actively collected and analyzed using Gas Chromatography-Flame Ionization Detection (GC-FID). The results showed that the concentrations of BTEX were higher in the indoor air compared to the outdoor air. The highest mean concentration of benzene (153.22 ± 34.21 μg m−3), toluene (94.41 ± 25.25 μg m−3), and xylenes (385.38 ± 34.21 μg m−3) was found in auto paint (AP) workshops, while the highest mean concentration of ethylbenzene (43.39 ± 12.57 μg m−3) was observed in auto body (AB) workshops. The significant negative correlations between benzene, ethylbenzene, xylene isomers, and relative humidity (RH) indicated that controlling humidity is an effective strategy. The mean inhalation lifetime cancer risk (LTCR) for benzene in both indoor and outdoor air of all automobile workshops exceeded the EPA (Environmental Protection Agency) recommended limits. The highest mean LTCR values for benzene and ethylbenzene were observed in the AP (3.24E10-4) and AB (2.95E10-5) workshops, respectively. The hazard quotient (HQ) of benzene and Xylene in the indoor air of the AP and AB workshops was >1, which indicates that the non-carcinogenic risks associated with exposure to these compounds are considerable. This study underscores the need for international attention to BTEX pollution in automobile workshops, highlighting the global health risks. The findings provide crucial data for developing strategies to mitigate these risks and protect workers’ health.

Acute and chronic risk assessment of BTEX in the return water of hydraulic fracturing operations in Marcellus Shale

Environmental pollution caused by human activities is a pressing issue in developed countries. In this context, it is vital to establish methodologies for the early and reliable estimation of the health risks posed by potential pollutants. Flowback and produced water (return water) from shale gas operations can contain toxic compounds, of which BTEX (benzene, toluene, ethylbenzene, and xylenes) are of concern due to their toxicity and frequent presence above regulatory limits. The return water generated by these operations is stored in ponds or tanks before reaching its final destination. Over time, the composition of this water changes, and leaks or inadequate contact can harm the environment and human health.Here we developed a risk assessment framework to evaluate the temporal evolution of chronic and acute BTEX exposure risks caused by accidental return water leakage. We applied the approach to a hydraulic fracturing operation in the Marcellus Shale Formation. Starting with a time series of BTEX concentrations in the return water, our method deploys transport models to assess risk to health. Our approach compares exposure levels with regulatory limits for inhalation, ingestion, and dermal contact. By identifying the risk levels, exposure pathways, and control parameters in the case study for a range of periods after leakage, our study supports the implementation of appropriate risk mitigation strategies. In addition, by examining risk variation under arid, semi-arid, and humid climate scenarios, the study reveals the impact of climate change on soil characteristics and BTEX transport.The development and application of this methodology is an important step in addressing concerns regarding shale gas operations. The approach proposed paves the way for sustainable practices that prioritise the protection of human health and the environment.

Ambient levels of BTEX at roadside in northern Iraq and its relationship with traffic volume.

Among the mono-aromatic volatile organic compounds, benzene, toluene, ethylbenzene and xylene (BTEX) have occupied a large area in air pollution studies due to their carcinogenic and non-carcinogenic effect. In this study, a station was used to monitor BTEX concentrations at roadside in urban area at Mosul city along a year, with traffic volume and meteorological factors measurement. The annual mean of benzene was 12 µg/m3, which is more than twofolds of the standard European Union level of 5 µg/m3. In addition, 87.4% of the measured values in summer was higher than the standard level at roadside. Benzene was dominant in spring and summer among BTEX species, while the dominance changed to ethylbenzene in autumn and winter. Besides, benzene, toluene, ethylbenzene and o-xylene showed significant seasonal variation. BTEX and benzene concentrations increased as the number of vehicles on gasoline and diesel increased. In contrast, toluene and ethylbenzene were more affected with number of vehicles on diesel. On the other hand, the weak significant correlations among BTEX species and high T/B ratio indicate the difference in fuel types used and the existence of additional sources of BTEX emission with the vehicular exhausts. These results can be utilized in determining the control strategy in air quality management in Mosul city.

Removal of BTEX (Benzene, Toluene, Ethyl benzene and Xylene) from aqueous solutions using surface-modified zeolite

<p>BTEX, also known as benzene, toluene, ethyl benzene, and xylene, is a common gasoline oxygenate. The contamination of groundwater and surface water with BTEX and its primary breakdown product has drawn a lot of attention. However, surface-modified zeolite's sorption mechanisms and affinity for BTEX can be employed to potentially remove these toxins from water. Tert-butyl alcohol (TBA) was utilized to alter the morphology of the adsorbent. Based on the findings, it can be concluded that zeolites have a greater capability for removing emerging chemicals. Some of the emerging compounds' relatively large dimensions limit their natural ability to lower values. Gas chromatography was used to determine the BTEX concentration decrease range. The Yoon-Nelson and Adams-Bohart model's use of mathematical modelling to determine the efficacy of the column's adsorption. The model with the highest R2 values for characterizing equilibrium isotherm data describes equilibrium adsorption data. To gain an understanding of the shape, pore structure, and active sites, the characterisation is concentrated on quantitative analysis using XRD, qualitative analysis using FTIR, and optical study using SEM.</p>

Impact of Artisanal Crude Oil Refinery on Physicochemical and Microbiological Properties of Soil and Water in Igia-Ama, Tombia Kingdom, Rivers State, Nigeria

This study aimed to determine the impact of artisanal refinery operations on the physicochemical and microbiological properties of soil and water in Igia-Ama, Tombia Kingdom, Rivers State, Nigeria. Physicochemical parameters along with concentrations of heavy metals, polyaromatic hydrocarbons (PAHs), total petroleum hydrocarbon (TPH), benzene, toluene, ethylbenzene and xylene (BTEX), and polychlorinated biphenyls (PCB) were determined in soil and water samples using standard methods. Microbial populations were determined using standard plate count. Microbial isolates were identified based on their cultural, morphological and biochemical characteristics. Results show that concentrations of monitored physicochemical parameters differed significantly (p<0.05) between impacted sites and control as well as between dry and wet season. Heavy metals, PAHs, TPH, BTEX and PCB concentrations were higher in the impacted sites than in the control (significant, p<0.05), and also differed significantly between dry and wet season. Microbial counts varied between polluted samples and control as well as between dry and wet season, though not significantly different (p>0.05). Bacterial isolates in polluted soil samples were identified as Enterobacter sp., Bacillus sp., Micrococcus sp., Staphylococcus sp. and Pseudomonas sp. Bacteria in polluted water samples were identified as Staphylococcus sp. and Escherichia coli. Fungi in polluted soil samples were identified as Aspergillus sp., Penicillium sp. Fusarium sp., Rhodotorula sp., Exophiala sp. and Crypotococcus sp. While only Penicillium sp. was isolated in polluted water sample. Artisanal crude oil refinery operations significantly impacted the physicochemical properties of soil and water in the study area but not the microbiological properties. The levels of heavy metals, PAHs, TPH and BTEX in the soil and water suggest the need for remediation of the impacted environment.

Air pollution characteristics and human health risk assessment of underground parking garages in Xi’an, China

Due to the rapid increase of population density and automobile vehicle numbers in mega-cities, large underground garages have become universal supporting facilities to meet the demand for parking spaces in the recently-built commercial complexes and high-rise residential communities. Natural ventilation was insufficient to discharge vehicle-induced pollutants out of the enclosed underground spaces, which could pose a potential threat to people’s health. This study aims to determine the spatial and temporal distribution characteristics of pollutants concentration and the health risk of underground parking garages (UPGs)’ staff and users. Field measurements were conducted on the air pollutants concentrations and the users’ exposure characteristics in 11 commercial UPGs and three high-rise residential UPGs with natural ventilation in Xi’an. The pollutants concentrations were higher in the afternoon and morning of commercial and high-rise residential UPGs. In general, the particulate matters (PM2.5 and PM10), HCHO, TVOC and BTEX (benzene, toluene, ethylbenzene and xylenes) concentrations in commercial and residential UPGs were 0.069/0.067 mg/m³, 0.12/0.097 mg/m³, 0.014/0.017 mg/m³, 1.8/1.8 mg/m³, 0.056/0.10 mg/m³, 0.19/0.29 mg/m³ and 0.41/0.49 mg/m³, respectively. TVOC and BTEX concentrations in UPGs significantly correlated with traffic volume ( p < 0.01). In different groups, the entropy values of carcinogenic and non-carcinogenic risks were: staffs > children travelling with adults > adults. In particular, occupational long-term (employee) exposure could lead to both carcinogenic and non-carcinogenic risks.

The concentration of BTEX in selected urban areas of Malaysia during the COVID-19 pandemic lockdown

Volatile organic compounds (VOCs) such as benzene, toluene, ethylbenzene and xylene (BTEX) are air pollutants that harm human health. This study aims to identify BTEX concentrations before the lockdown known as the Movement Control Order was imposed (BMCO), during the implementation of the Movement Control Order (MCO), and then during the Conditional Movement Control Order (CMCO). These orders were introduced during the COVID-19 pandemic in Malaysia. The study utilised data measured by the continuous monitoring of BTEX using online gas chromatography instruments located at three urban area stations. The results showed that the BTEX concentrations reduced by between −38% and −46% during the MCO compared to the BMCO period. The reduction of human mobility during the MCO and CMCO influenced the lower BTEX concentrations recorded at a station within the Kuala Lumpur area. The results of the BTEX diagnostic ratios and principal component analysis showed that the major source of BTEX, especially during the BMCO and CMCO periods, was motor vehicle emissions. Further investigation, using correlation analysis and polar plots, showed that the BTEX concentrations were also influenced by meteorological variables such as wind speed, air temperature and relative humidity.

Global preterm births attributable to BTEX (benzene, toluene, ethylbenzene, and xylene) exposure

Epidemiological studies have shown that long-term exposure to toxic volatile organic compounds, such as benzene, toluene, ethylbenzene, and xylene (BTEX), is associated with preterm births (PTB). However, global PTB attributable to long-term BTEX exposure has not been reported in the literature yet. In this study, we employed a global chemical transport model, GEOS-Chem (Goddard Earth Observing System coupled with chemistry), in conjunction with an epidemiological model, to quantify the global country-specific PTB associated with long-term BTEX exposure at the horizontal resolution of 1 km × 1 km for the year 2015. Model simulated surface annual mean BTEX concentrations in GEOS-Chem have been thoroughly evaluated against global in-situ observations, which demonstrated that model simulated BTEX concentrations fairly agreed with observations but tended to be underestimated in India. Our study found that the global annual total PTB attributable to BTEX was 2.01 million [95% confidence interval (95CI): 1.16–2.70 million] in 2015, with largest contributions from India (28.3%), followed by China (27.5%), Pakistan (6.2%), Indonesia (4.2%), Bangladesh (3.7%) and United States (2.3%). The global annual total PTB due to BTEX exposure accounted for 19.6% (95CI: 11.3–26.4%) relative to the global annual total all-cause PTB (10.24 million) in 2015. Our study has significant implications on air pollution mitigation policy associated with country-specific anthropogenic BTEX emission reductions to achieve the benefit of human health.

Association between BTEX (benzene, toluene, ethylbenzene and xylene) concentration in ambient air with hematological and spirometric indices: a population-based study

The study aimed to evaluated the relationship between BTEX (benzene, toluene, ethyl benzene and xylene) concentrations in the ambient air with human biomarkers in Assaluyeh city, Iran. According to the results, the average benzene concentration in the high pollution city was measured at 30.05 µg/m3, which is higher than the value recommended (0.03 mg/m3) by the U.S. Environmental Protection Agency (U.S. EPA). The mean spirometric parameters of the resident population in two high and low pollution areas were forced vital capacity (FVC) (high = 4.52; low = 4.78 L), forced expiratory volume in 1 second (FEV1) (high = 3.52; low = 3.88 L), FEV1/FVC (high = 77.9; low = 82.08%), peak expiratory flow (PEF) (high = 9.76; low = 27.85 L/min), and forced inspiratory flow 25–75% (FEF25-75) (high = 3.17; low = 3.95 L/s). Besides, no statistically significant difference was observed between the two groups by comparison of blood tests and the mean concentration of BTEX. BTEX concentration was measured at zero in low pollution areas due to lack of traffic and industries, but it was higher than the respiratory air standard and in the high-pollution area due to the being close to gas and petrochemical stations and industries in the surrounding. As a result, prolonged exposure to higher concentrations of BTEX increases the risks of respiratory dysfunction.

Spatial distribution of BTEX emission and health risk assessment in the ambient air of pars special economic energy zone (PSEEZ) using passive sampling

Benzene, toluene, ethylbenzene and xylene (BTEX) are a challenging group of volatile organic compounds in industrial and energy areas. Since these aromatics may cause serious diseases such as cancer and respiratory illnesses, they must be monitored. Pars Special Economic Energy Zone (PSEEZ) in Iran is the second largest energy zone of the world with numerous gas refineries and petrochemical complexes for producing a wide range of products. This study is focused on determination of BTEX concentration in the whole South Pars area (46 sampling points) which is the active site of PSEEZ using passive sampling. Then, the results of the passive sampling are used for providing spatial distribution of BTEX using GIS. The annual BTEX measurements revealed that benzene and toluene concentration violates the maximum permitted values at numerous points most of which are located in the vicinity of petrochemical complexes. Active sampling in these complexes not only confirms the results of passive sampling, but also suggests a more intensified BTEX pollution in the air quality of the area which reaches as high as 3500μg.m-3 and 18,000μg.m-3 for benzene and toluene, respectively, being far beyond the acceptable standards. Health risk analysis also confirms the intensity of BTEX at the selected points. This study suggests a reconsideration of the location of non-operational sites and personnel who are more vulnerable to BTEX contamination. Also, BTEX profile provided by GIS in this research gives a suitable plan for relocating.

BTEX levels in rural households: Heating system, building characteristic impacts and lifetime excess cancer risk assessment

BTEX (benzene, toluene, ethylbenzene, and xylene) are a group of toxic organic compounds that exposure to them can cause adverse short and long terms health effects. We measured the levels of BTEX in the indoor and outdoor air of rural areas in Ardebil, Iran. We further assessed their health risks and determinants parameters. BTEX were sampled by drawing air through activated charcoal tubes, using low flow SKC pumps. Samples were extracted by adding carbon disulfide and analyzed by subjecting the aromatic fraction to GC-FID. The results indicated that the concentrations of BTEX in the indoor air were significantly higher than those of outdoor (p-value<0.05). The mean indoor concentrations of benzene, toluene, ethylbenzene, and xylene were 41.69 ± 30.70, 96.73 ± 60.75, 38.73 ± 33.59, and 59.42 ± 35.99 μg m−3, while the mean outdoor concentrations of them were 8.94 ± 7.32, 36.93 ± 21.82, 7.66 ± 5.63, and 18.14 ± 10.25 μg m−3, respectively. The concentrations of BTEX in indoor and outdoor of the rural areas that used kerosene fuel for heating systems were significantly higher than those used natural gas. The results indicated that the tobacco smoke is a notable temporary source of indoor BTEX. The mean inhalation lifetime cancer risk (LTCR) value of benzene for residents of rural houses with the natural gas and kerosene heating systems were 28.6 × 10−6 and 97.2 × 10−6, while for ethylbenzene these figures stood out at 29.1 × 10−6 and 95.8 × 10−6, respectively. LTCR value for residents who used kerosene fuel for heating was higher than the World Health Organization (WHO) recommended limit.

Measurement of BTEX (benzene, toluene, ethylbenzene and xylene) concentration at gas stations

Background: Fuel stations are one of the major sources of air pollution with volatile organic compounds, especially the four main petrol compounds benzene, toluene, ethylbenzene, and xylene (BTEX). BTEX in gasoline enters the air of gas stations due to high evaporation of gasoline. Therefore, determining the concentration of these compounds in gas stations in crowded and busy cities is one of the important priorities of environmental health, which is doubly important in terms of its negative effects on health. Methods: In this descriptive cross-sectional study, a total of 39 samples were collected from 13 gas stations. Sampling was performed in autumn 2018 in three working shifts (morning, noon, and night). The method NIOSH-1501 (i.e., using charcoal sorbent tubes and SKC pump with a flow rate of 0.2 L/min) was used for sampling the BTEX compounds. The mean difference and correlation of BTEX compounds based on meteorological parameters and the number of nozzles in gas stations were assessed using one-way ANOVA and correlation tests. Results: The mean and standard deviation of benzene, toluene, ethylbenzene, and xylene concentrations in the air of fuel stations were 2.784±1.461, 3.495±1.390, 2.091±0.811, and 1.140±0.419 mg/m3, respectively. The relationship between BTEX compounds and meteorological parameters such as humidity and exposure time is very important. There is a strong correlation between the concentrations of BTEX compounds. The highest correlation was observed between benzene and toluene and the lowest one was observed between benzene and xylene. In this study, no significant relationship was observed between air temperature and concentration of BTEX compounds, but there was a relationship between relative humidity and the concentration of BTEX compounds. Conclusion: The average benzene concentration in the air at the fuel stations was about 5.5 times the standard limit. Authorities should improve fuel quality and reduce its evaporation through engineering measures to overcome the issue.

Ambient BTEX Concentrations during the COVID-19 Lockdown in a Peri-Urban Environment (Orléans, France)

During the period from 17 March to 10 May 2020, France saw dramatic shifts in domestic, industrial and transport activities as a national lockdown was introduced. So far, studies have generally focused on urban settings, by contrast, this work reports data for a peri-urban location. Air samples were collected and analyzed using a fully automated GC-MS-FID system in an air quality monitoring station situated in the suburbs of Orléans, France. Average concentrations of BTEX (benzene, toluene, ethylbenzene, and xylenes) before, during, and after lockdown, were 402 ± 143, 800 ± 378 and 851 ± 445 pptv, respectively. Diurnal variation in BTEX and correlations between each of its components were analyzed to determine its various sources. The toluene/benzene (T/B) and m,p-xylene/ethylbenzene (MP/E) ratios, photochemical ages were used to explore whether the BTEX were from local or more distant sources. Together with a host of complementary measurements including NOx, O3, black carbon, meteorological parameters, and anthropogenic activities, we were able to make some inferences on the sources of BTEX. The results suggest that although anomalous local anthropogenic activity can lead to significant changes in BTEX concentrations, pollution levels in Orléans are mostly dependent on meteorological conditions, specifically whether the winds are coming from the Paris region. It appears, based on these measurements, that the pollution in the Orléans area is very much tied to the nearby megacity of Paris, this may be true for other peri-urban sites with implications for city planning and pollution mitigation strategies.

Evaluation of potential human health risks from exposure to volatile organic compounds in contaminated urban groundwater in the Sava river aquifer, Belgrade, Serbia.

The oil pollutant in the Sava River aquifer in the residential area of Belgrade, Serbia was investigated in order to analyze the extent, origin and spatial distribution of the pollution, with the aim to estimate potential human health risks from exposure to the compounds detected. Analytical methods indicated that the dominant compounds in this oil pollutant were gasoline range organic compounds. Benzene, toluene, ethylbenzene and xylenes (BTEX) were identified as compounds of concern and quantified by headspace gas chromatography. The concentrations of benzene measured at all sampling points were higher than the remediation value while the maximum concentrations of BTEX quantified were among the highest concentrations of these compounds reported in the petroleum-contaminated aquifers in the world. The assessment of the human health risks from exposure to BTEX-covered industrial scenario for adult receptors and residential scenario for adult receptors and children. The exposure routes analyzed were dermal contact with and ingestion of contaminated water, considering both cancer and non-cancer effects. The analysis of the lifetime incremental cancer risk indicated the potential for adverse health effects for human exposure at the investigated location, and because of that it was interpreted as an unacceptable risk level or risks of high priority which required immediate consideration for remedial measures at this location. A complete set of mitigation measures was proposed including: groundwater decontamination treatment, installation of filters for tap water, development of the system for monitoring of BTEX in the groundwater and development of the emergency response capacities at this location.

Field evaluation of a low-uptake VOC passive sampler suitable for long-term deployments

Passive samplers have proven to be effective for continuous monitoring of volatile organic compounds (VOCs) in ambient air in remote, urban and industrial environments. Thermal desorption tubes fitted with endcaps that facilitate passive uptake through diffusion are now routinely used for monitoring fugitive benzene emissions from refineries and petrochemical facilities across North America (EPA Method 325A/B). However, deployment periods of 14 days are typically employed to minimize the risk of poor retention, requiring 26 deployments per year to return an annual average concentration for comparison with chronic exposure health-based standards. Here, we explore extending the deployment duration of these passive samplers to one, two and three months by limiting VOC uptake rates using an alternative diffusive endcap featuring a smaller cross-sectional area. Field testing was performed beside a major highway during two separate three-month campaigns. Uptake rates for benzene, toluene, ethylbenzene and xylenes (BTEX) were observed to remain linear for deployments of up to three months when using the low-uptake endcaps. Application of the low-uptake endcaps and the uptake rates determined here will enable annual average concentrations of BTEX to be calculated using only four tube deployments per year. The cost savings associated with this decreased deployment frequency will facilitate increased spatial resolution during future exposure assessment studies. The stability of selected air toxics within the tubes was also assessed and the results suggest that while aromatic VOCs are stable for storage times of at least 70 days, chloroform and trichloroethylene begin to degrade within two weeks of sampling.

Benzene, Toluene, Ethylbenzene and Xylene (BTEX) Concentrations in Urban Areas Impacted by Chemical and Petrochemical Industrial Emissions.

The Metropolitan Region of Rio de Janeiro is the second largest urban and industrial region in Brazil. While the south and south-east areas are affected by vehicular emissions, the districts and cities located in the northern area are subjected to industrial emissions and have the poorest air quality of the region. In this study, BTEX concentrations were determined in the District of Irajá, a residential area located in the north of the city of Rio de Janeiro, approximately 25km from the industrial zone, as well as in the District of Jardim Primavera, in the city of Duque de Caxias. The mean values for total BTEX concentrations were 38.4 ± 11.7 and 44.6 ± 29.3μgm-3, in Irajá and Jardim Primavera, respectively, which are higher than those previously reported for other areas. The benzene/toluene rates, (approximately 0.5 for both sampling sites), were also higher than typical values that were determined for diesel and gasoline emissions through dynamometer experiments.

Level of air BTEX in urban, rural and industrial regions of Bandar Abbas, Iran; indoor-outdoor relationships and probabilistic health risk assessment

This study focused on the measurement of BTEX (benzene, toluene, ethylbenzene and xylene) concentrations in the air of various regions and indoor-outdoor environments in Bandar Abbas, Iran. Air samples were taken actively and analyzed by gas chromatography-mass spectrometry (GC-MS) during two one-month periods i.e., Feb 2020 (period I) and Sep/Oct 2020 (period II). The mean air temperature and the levels of all BTEX compounds were higher in period II. The highest total BTEX (t-BTEX) levels (median [min-max]) were found in the urban region (18.00 [5.21–67.24] μg m−3), followed by industrial region (7.00 [2.05–14.76] μg m−3) and rural region (2.81 [ND-7.38] μg m−3). The significant positive correlations between all BTEX compounds and T/B ratio >1 indicated the vehicular traffic as the main source of emission. At 95th percentile probability, the non-cancer risk of t-BTEX in urban region was only less than one order of magnitude below the threshold level of unity (1.91E-01) and the cancer risk of benzene exceeded the recommended level of 1.0E-06 by U.S. EPA in urban (7.69E-06) and industrial (2.97E-06) regions. It was found that the indoor/outdoor ratio of BTEX concentration in beauty salon and hospital was greater than 1. Overall, the current levels of BTEX in the ambient air of study area, especially near urban roadside and in some indoor environments, should not be overlooked and appropriate mitigation actions should be undertaken.

Monoaromatic Hydrocarbon Bioremediation of Hydrocarbon-contaminated Soil Using HBB5 Biosurfactant Produced by Pseudomonas xiamenensis

Biodegradation of benzene toluene ethylbenzene and xylenes (BTEX) is a slow and complex process. However, many microbial organisms have been shown to possess the capacity to biodegrade various components of a hydrocarbon. This study was aimed at investigating the role of biosurfactant on soil polluted with these monoaromatics. Samples were collected and analyzed using standard techniques. The biodegradation set up was carried out using five earthen pots; each containing unpolluted soil, polluted soil alone, polluted soil + poultry wastes, polluted soil + HBB5 biosurfactant and polluted soil + poultry wastes + HBB5 biosurfactant. The biodegradation of BTEX were periodically monitored every seven days for 28 days using gas chromatograph-mass spectrometer coupled with head space (GC-MS-HS). The respective initial and final concentrations of BTEX (ppm) were as follows; 0.7936 and 0.2063, 0.9733 and 0.0231, 0.9526 and &lt;0.0001, 0.9241 and &lt;0.0001 with degradation efficiencies of 74.0%, 97.6%, 100% and 100% for polluted soil alone, polluted soil + poultry wastes, polluted soil + HBB5 biosurfactant and polluted soil + poultry wastes + HBB5 biosurfactant respectively. The microbial counts increased greatly, and the concentrations of the limiting nutrients reduced during the experimental period. The effective treatments for bioremediation increased in the following order: polluted soil alone &lt; polluted soil + poultry waste &lt; polluted soil + HBB5 biosurfactant &lt; polluted soil + poultry waste + HBB5 biosurfactant. Results clearly showed that application of HBB5 biosurfactant only or in combination with poultry wastes has the ability to degrade ethylbenzene and xylenes (BTEX) and thus, can be employed in the clean-up of crude oil contaminated soil.

Assessment of H2S and BTEX concentrations in ambient air using passive sampling method and the health risks.

Wastewater treatment plants (WWTPs) may be a source of nuisance in neighbouring places due to hydrogen sulphide (H2S) and BTEX (benzene, toluene, ethylbenzene, and xylenes) emissions. In this study, samples were collected from WWTP workplace ambient air and outdoor ambient air around one of the largest WWTPs in Istanbul with a capacity of 250,000 m3/day to evaluate the effects of H2S and BTEX emissions. Samples were collected in three seasons for 15-day durations: winter (November 2015), spring (May 2015), and summer (August 2016). Average concentrations of H2S and BTEX were determined as 1.1 and 56.2µg/m3, respectively. Average concentrations BTEX components were 4.9, 20.7, 6.4, and 24.2µg/m3, respectively. Health risk assessment for plant workers and local residents was performed for H2S and BTEX inhalation exposure using the method by USEPA. Results show that H2S and BTEX emissions do not have harmful effects on human health.

The Seasonality Impact of the BTEX Pollution on the Atmosphere of Arad City, Romania.

Benzene, toluene, and total BTEX (benzene, toluene, ethylbenzene, and xylene) concentrations registered for one year (2016) have been determined every month for one high-density traffic area. The assessment was performed in Arad City, Romania, to evaluate these pollutants and their influence on the inhabitants’ health. The contaminants were sampled using a static sampling method and analyzed by gas chromatography coupled with mass spectrometry. Benzene was the most dominant among the BTEX compounds—the average concentrations ranged from 18.00 ± 1.32 µg m−3 in December to 2.47 ± 0.74 µg m−3 in August. The average toluene concentration over the year was 4.36 ± 2.42 µg m−3 (with a maximum of 9.60 ± 2.39 µg m−3 in November and a minimum of 1.04 ± 0.29 µg m−3 in May). The toluene/benzene ratio (T/B) was around 0.5, indicating substantial contributions from mobile sources (vehicles). The emission and accumulation of different aromatic compounds (especially benzene) could deteriorate the urban air quality. The lifetime cancer risk (LTCR) for benzene was found to be more than 10−5 in winter, including the inhabitants in the “probable cancer risk” category.