Wideband Bandpass Filter Research Articles

A creative hybridization of metamaterial CSRR and multiple-mode resonators for designing a compact wideband bandpass filter for 5G/IOT/WLAN/Wi-Fi 6E applications

A creative hybridization of metamaterial CSRR and multiple-mode resonators for designing a compact wideband bandpass filter for 5G/IOT/WLAN/Wi-Fi 6E applications

Miniaturized broadband high out-of-band rejection bandpass filter based on spoof surface plasmon polaritons with defected ground structure

In this paper, a novel compact bandpass filter (BPF) with a wide out-of-band rejection is proposed. It can achieve broadband characteristics by combining hollow bowtie-type spoof surface plasmon polaritons (SSPPs) with complementary H-type defected grounded structures (DGSs) through aperture coupling. Compared with the conventional SSPP unit cells, the hollow bowtie-type structure exhibits much better slow-wave characteristics. The introduced slant antenna type port-coupling can produce a very strong high-performance rejection outside the high frequency stopband. Simulation results show that the SSPPs-DGS-based BPF has an excellent band pass characteristics in a broadband range with − 3dB fractional bandwidth of 43.5% at center frequency f0 of 2.04 GHz. The return loss in the passband is better than − 12 dB. Furthermore, because of the multiple transmission zeros generated in upper-stop-band, the designed BPF has an extremely strong out-of-band rejection of -40dB from 1.5 f0 to 4 f0 (f0 is the center frequency). The designed SSPPs-DGS-based BPF is fabricated by conventional printed circuit board (PCB) technology with a compact size of only 0.68λg*0.34λg (λg is the wavelength at the center frequency). The measured results have a good agreement with the simulation ones, which verifies the rationality and feasibility of the design. The miniaturized wideband BPF with broad out-of-band rejection may make it has good application prospect in the new generation microwave communication field.

A ridged waveguide filter design with ultra-wideband and harmonic suppression

In this paper, a new structure for wide-band rectangular waveguide bandpass filters with distinguished harmonic suppression is presented. The filter is realized by using ridged waveguides in both resonant cavities and coupling windows and a metal plate, which performs like a low-pass filter and makes it arduous to form parasitic passbands. According to the field analysis and out-of-band response, the ridge structure can expand pass bandwidth and obtain a wide stopband by harmonic suppression. The filter is designed to perform a passband of 67% fractional bandwidth at center frequency at 75 GHz. The harmonic suppression of the design is increased from 1.5 times to 3.6 times the center frequency of the filter with 20 dB suppression levels. Finally, the measurement results validate the proposed design.

Generation of frequency-shift keying (FSK) and amplitude-shift keying (ASK) RF signals by diode-tuned Fourier domain mode-locked opto-electronic oscillator

An approach to the generation of frequency-shift keying (FSK) and amplitude-shift keying (ASK) RF signals with a diode-tuned Fourier domain mode-locked opto-electronic oscillator (FDML OEO) is proposed and demonstrated. We use a low-cost varactor diode tuned phase shifter to form a high speed tunable bandpass filter (TBF) to implement the FDML-OEO. When a square wave modulation signal is used to drive the TBF, FSK RF signals are generated, with the flexibility to easily change the center frequency and tuning bandwidth of the FSK signals. For the ASK RF signal generation, a band-pass filter (BPF) with a bandwidth less than the TBF tuning range is added to the FDML OEO RF feedback loop. When the TBF center frequency hops in and out of the BPF bandwidth within a mode locking period, the FDML OEO generates ASK RF signals. The phase noises of the FSK and ASK RF signals generated by our FDML-OEO are both measured to be −123dBc/Hz at 10 kHz offset frequency. The key significance of this approach is that no microwave source is required to generate the ASK signal and reconfigurable FSK and signals, which may find wide applications in future radar and communications systems.

Novel design and implementation of 3d packaged wideband bandpass filters

This study presents an innovative method for designing a 3D packaged wideband bandpass filter (BPF) by vertically integrating a high-pass filter (HPF) and a low-pass filter (LPF) using an air cavity and vertical interconnect accesses (VIAs). This integration enhances performance while significantly reducing system size. The fabricated BPF, constructed on multilayer substrates, achieves a passband from 2.175 to 4.2 GHz with less than 2.5 dB insertion loss and a return loss exceeding 10 dB. The design utilizes a partial substrate integrated suspended line (SISL) structure, enabling precise control over the equivalent dielectric constant and characteristic impedance to optimize insertion loss. The height of the air cavity, determined through theoretical analysis and S-parameter inversion, is critical for achieving optimal filter performance. The methodology allows for independent circuit designs on each layer, resulting in a 3D assembly. This refined approach makes it easier to produce compact bandpass and multi-band filters, simplifying circuit development and enabling scalable fabrication. This design is versatile across different frequency ranges, demonstrating significant practical and theoretical benefits.

High selectivity wideband two‐channel bandpass filter for 5G microwave communication systems

AbstractA two‐channel high‐selectivity, wideband bandpass filter has been presented. This is based on a microstrip mixed‐impedance resonator and defected ground structure with the mixed coupling strategy. Two pairs of peripheral stepped‐impedance resonator (SIR) structures are used as stubs, achieving TZs at the immediate lower and upper cut‐off sides of the passband and control the bandwidth, while the other two transmission zeros on the upper cut‐off side are yielded through the defected ground structure, and the coupling between the SIR and uniform‐impedance resonators components, respectively. A prototype of the circuit is fabricated and measured for validation. The measured results exhibited insertion and return losses better than 1.1 and 20.5 dB, respectively, and high isolation levels exceeding 19 dB. In total, four transmission zeros are achieved. The designed filtering circuit realized a 3‐dB fractional bandwidth of 58.1%. There is a 0.95f0 stopband at the upper cutoff. The fabrication of the prototype shows good agreement between the simulated and measured performance.

A compact dual‐band bandpass filter based on coupled stub‐loaded square ring resonators by using transversal signal‐interaction concepts

AbstractIn this paper, a novel dual‐band wideband bandpass filter (BPF) based on transversal signal‐interaction concepts with a wide upper stopband is proposed and investigated. The designed specification of two passbands can be managed and satisfied based on the independent controllable fractional bandwidth of the two passbands and the centered frequencies. The centered frequencies of dual‐band BPF are, respectively, 0.79 GHz (ƒ1) and 1.24 GHz (ƒ2) with 3 dB fraction bandwidths of 26.54% and 11.3%. Two transmission paths consisting of coupled stub‐loaded square ring resonators and anti‐coupled shorted lines are used to realize signal cancellation of multiple transmission path signal transmission from Port 1 to Port 2. Eleven transmission zeros (TZs) modify harmonic suppression up to 10 ƒ1 with stopband rejection higher than 15 dB. Butterworth lumped notch network and step impedance resonator (SIR) are also utilized to improve the selectivity and harmonic suppression. A compact filter with a circuit size of 0.08λg × 0.08λg is implemented and tested. Good agreement between simulation and measured results verifies the reliability of the designing scheme.

High-selectivity wideband bandpass filter based on quintuple-mode stub-loaded resonator and defected ground structures

Abstract A high-selectivity wideband bandpass filter (BPF) based on a quintuple-mode stub-loaded resonator and defected ground structures (DGSs) is presented. Thanks to the symmetrical topology, the even/odd theory is adopted for analyses. By properly adjusting the stub dimensions, the resonant frequencies of the transmission poles and zeros can be controlled to obtain wide passband and sharp out-of-band rejection performances. The bandwidth of the upper stopband is further extended by introducing a pair of DGSs under the interdigital coupled line feeding structures, and the spurious response rejection is improved by 18.9 dB. A BPF prototype that operates at 6 GHz with a fractional bandwidth (RBW) of 70 % is manufactured for validation. The measured insertion loss and return loss are 1.3 and 17 dB, respectively. The measured out-of-band rejection over DC-2 GHz and 8.8–21 GHz are better than −30 dB.

Design of highly efficient filtering power amplifier with a wideband response for sub-6 GHz 5G applications

This paper presents the design of a filtering power amplifier (PA) with extra-high power-efficiency and wide bandwidth. To accomplish this, a novel approach is adopted by utilizing a wideband bandpass filter (BPF) as the output matching network (OMN) for the PA. The BPF compromises two paths, where each path consisting of two identical coupled lines that are interconnected to form a ring structure. The suggested configuration eliminates the need for a conventional OMN by integrating the input port of the filter with the drain node of the transistor, resulting in reduced size and losses and improved amplifier performance. The filter concept is illustrated using coupling matrix synthesis. A proof-of-concept filtering PA has been designed using a commercially available 10 W GaN HEMT. This amplifier was designed to operate in the frequency range of 3.0–5.0 GHz, yielding a fractional bandwidth of 50 %. According to achieved results, the drain efficiency and output power are 43.8–70.5 % and 40.2–41.8 dBm, respectively. As a result, the suggested filtering PA demonstrates significant performance in terms of filter bandwidth response and power amplification. Additionally, the proposed filtering PA has a broad operational bandwidth of 3.0–5.0 GHz, which covers the 5G New Radio (NR) n77 (3.3–4.2 GHz), n78 (3.3–3.8 GHz), and n79 (4.4–5.0 GHz) frequency bands.

Design of a miniaturized multi resonance resonator based highly selective dual wideband bandpass filter

This paper presents the design of a highly selective dual-wideband bandpass filter. The filter is designed by using multi-resonance resonator consisting of two stub-loaded step impedance resonators separated by an inter-digital capacitor. The inter-digital capacitor generates capacitive coupling, resulting in multiple resonating modes. The proposed filter generates two passband frequencies centered at 5.75 GHz and 11.5 GHz. Experimental measurements show that the maximum insertion loss in the passbands is 0.83 dB and 0.87 dB, while the reflection losses are better than 10.8 dB and 12.6 dB, respectively. The resonant frequencies can be adjusted by changing the length of the loaded stubs. The proposed dual-wideband bandpass filter offers improved out-of-band rejection and selectivity by generating seven transmission poles and seven transmission zeros around both passbands. The experimental results confirm the effectiveness of the proposed filter. Furthermore, the filter has a compact size of (0.61×0.66)λg, making it suitable for integration into microwave sensing devices.

Design of Coplanar Stripline Bandpass Filter With Reconfigurable Filter Switch

ABSTRACTThis article has designed a bandpass filter using a coplanar stripline stub (CPS) resonator consisting of open and short‐ended strip lines connected to the PIN diode switches. The use of spurline stub resonators inside CPS results in bandpass and bandstop filters, depending on the PIN diode switch configurations. The work presents a novel circuit architecture aimed at reducing the parasitic resonance of the spurline resonators and acquiring the necessary series stub characteristics. The proposed filter resonates at 6.9–9, 1.7–4.7, and 8.4 GHz when the PIN diodes are forward and reverse‐biased, respectively. It also resonates at 1–2.1, 4.8–5.3, and 6.9–9 GHz when one diode is reverse‐biased, and the other is connected in forward bias. An insertion loss below −0.55 dB and a return loss less than 10 dB have been obtained during simulation and measurement. The designed filter can find different applications for the 1.8 GHz GSM band, 2.4/5.8 GHz (WLAN), 3.6 GHz (WiMAX), long‐term evolution (LTE), and WIFI. The filter can be used in various multi‐frequency systems owing to its compact size. The measured and simulated findings of the proposed CPS spurline stub resonator wideband bandpass filters are substantially consistent.

Miniaturized wideband bandpass filter using capacitor-loaded coupled-lines

A compact wideband bandpass filter (BPF) based on capacitor-loaded parallel coupled-lines and open/short stubs is presented in this brief. The proposed BPF contains four lumped capacitors that can reduce the circuit size, which are connected in series or parallel with the coupled microstrip lines and open/short stubs. Owing to the symmetry of the circuit topology structure, odd- and even-mode methods are used for analysis, then the 3-dB fractional bandwidth (FBW) and return loss (RL) can be calculated by MATLAB using impedance deduction of each branch circuit. To demonstrate the feasibility of the proposed design, a wideband BPF prototype with a center frequency of 0.23 GHz and a 3-dB FBW of 117.8 % is fabricated and measured, which exhibits a miniaturized size of 0.026λg × 0.079λg (λg: guided wavelength at the center frequency). The results of experiment are very consistent with theoretical calculations, circuit and electromagnetic simulations, validating the concept of the proposed technique.

Surrogate-Assisted Differential Evolution for the Design of Multimode Resonator Topology.

The microstrip devices based on multimode resonators represent a class of electromagnetic microwave devices, promising use in tropospheric communication, radar, and navigation systems. The design of wideband bandpass filters, diplexers, and multiplexers with required frequency-selective properties, i.e., bandpass filters, is a complex problem, as electrodynamic modeling is a time-consuming and computationally intensive process. Various planar microstrip resonator topologies can be developed, differing in their topology type, and the search for high-quality structures with unique frequency-selective properties is an important research direction. In this study, we propose an approach for performing an automated search for multimode resonators' conductor topology parameters using a combination of evolutionary computation approach and surrogate modeling. In particular, a variant of differential evolution optimizer is applied, and the model of the target function landscape is built using Gaussian processes. At every iteration of the algorithm, the model is used to search for new high-quality solutions. In addition, a general approach for target function formulation is presented and applied in the proposed approach. The experiments with two microwave filters have demonstrated that the proposed algorithm is capable of solving the problem of tuning two types of topologies, namely three-mode resonators and six-mode resonators, to the required parameters, and the application of surrogated-assisted algorithm has significantly improved overall performance.

Investigating orthogonal frequency division multiplexing using high‐power LED for visible light communication

AbstractSpectrally efficient 16 quadrature amplitude modulation‐orthogonal frequency division multiplexing (QAM‐OFDM) system using specifications of commercially available high‐power phosphorous coated LED (PLED) is proposed in this study. To address the challenges of signal attenuation and limited bandwidth, systems integrated with a band pass filter (BPF) after the photodetector and optical preamplifier. The effect of BPF bandwidth and preamplifier gain on the performance of 16 QAM‐OFDM system have been investigated. Results demonstrated that 375 MHz bandwidth evaluated from 1.5 × symbol rate, offered an optimum performance achieving minimum bit‐error‐rate of 3.05 × 10−4. For preamplifier gain of 20 dB, we achieved a maximum distance of 3 m which is limited to 1.5 m for lower gain values. With BPF‐optimized bandwidth and a preamplifier gain of 20 dB, we have achieved a data rate of 5 Gbps for maximum distance up to 2 m while considering the super‐forward‐error‐correction limit of 1.863 × 10−2. With data rate of 6 and 7 Gbps, the distance lower down to 1.8 and 1.5 m, respectively.

Compact transversal signal-interaction wideband bandpass filter with multiple transmission zeros and wide stopband

In this paper, a compact wideband bandpass filter with multiple transmission zeros and a wide upper stopband is proposed based on the transversal signal-interaction concept. The filter has two transmission paths for signals to travel from the input port to the output port. The wideband bandpass filter is designed with a center frequency of 4.29 GHz (f0) and a 3-dB fractional bandwidth of 71.3 %. Six transmission zeros from 0 GHz to 4.2 f0 can be achieved due to the superposition of signals of the two transmission paths and the virtual short effect of open stub. The designed and fabricated wideband bandpass filter is of minimum insertion loss of 0.3 dB, group delay in the passband below 1.1 ns, and upper-sideband rejection up to 18 GHz (4.2 f0). Additionally, the proposed filter possesses compact size, and the overall circuit only occupies 0.23 λg × 0.15 λg (λg is the guide wave length of 50 Ohm microstrip line at 4.29 GHz). Measurement and simulation results are in good agreement.

A novel design method for wideband bandpass filters with fewer inductors

Inductors that are widely used in wideband filter designs could result in large filter size and high insertion loss. A novel design method using admittance matrix based on direct circuit implementation is introduced for wideband bandpass filters. Firstly, a frequency transformation is performed on cross-couplings to realize the conversion between inductor and capacitor, thereby reducing usage of inductors. Moreover, by virtue of an enhanced resonator (type I), an approach of adding extra transmission zero is proposed to improve the out-of-band rejection without any additional usage of inductors. Thirdly, based on the frequency transformation, another enhanced resonator (type II) is introduced to further improve the frequency characteristics without compromising usage of inductors. Finally, by cascading the enhanced resonators of type I and type II, a novel filter can be constructed. This novel filter is designed and fabricated using a glass-based integrated passive device (IPD) technology. The measurement results are highly consistent with the simulation results. It is shown that the proposed design method can reduce the filter size and thus improve the chip integration. It enriches the freedoms during the filter design.

Compact and miniaturized wideband bandpass filter based on substrate integrated waveguide and microstrip line

In this work, we present a simple design of a compact and miniaturized wideband bandpass filter (BPF) based on substrate integrated waveguide (SIW) and microstrip line. Through the order extension, the filtering effect and the order of the Chebyshev response of the designed BPF can be indirectly controlled by preserving square notches (SNs) on the SIW. By introducing one or two SNs in the SIW structure, the resonance frequencies of different modes can be controlled, thus achieving dual- and tri-mode BPFs with wideband and low insert loss. The working principle of the designed BPFs was illustrated by modal analysis, field distribution, and equivalent circuit theory. Based on this, the dual- and tri-mode BPFs with center frequencies of 6.8 and 7 GHz were designed and demonstrated numerically. Further experimental results indicate that the proposed tri-mode BPF has low insertion loss (0.25 dB), compact size (0.27λg2), and wideband bandwidth (60%). In addition, the tri-mode BPF achieves a broadband out-of-band rejection of 1.5f0 (f0 is the center resonance frequency) below the −10 dB level, making it highly promising for various applications in related fields.

A fast and effective approach for microstrip filter design using GA and TL-model

Microwaves and RF technology and their components like filters, antennas, etc. are commonly used in wireless networking and communication systems, wireless security systems, radar systems, and environmental remote sensing. In this paper, a fast and effective procedure has been proposed for microstrip filter design using a genetic algorithm (GA) with a transmission line model (TL). GA is modified to be highly efficient and accurate by encoding the topology. For the fixed filter topology, the electrical parameters of the filter are encoded in a single chromosome. To make the proposed procedure fast and effective, a transmission line model has been employed to compute the fitness value in GA. To demonstrate the effectiveness of the proposed procedure, a wideband second-order bandpass filter with a center frequency of 2.3 GHz is examined with a pair of short-circuited stubs and a pair of open-circuited stubs. The optimized design is validated using full-wave methods (MoM and EM simulator CST). The results show a low insertion loss of 0.1 dB and return loss better than 30 dB and a wide bandwidth of 46.95% with − 3 dB cutoff frequencies at 1.76 GHz and 2.84 GHz.

Wideband bandpass filter with ultra-wide stopband based on cross-shaped parallel coupled lines

A broadband out-of-band rejection capability and multiple transmission zeros of wideband bandpass filter are proposed and validated in this article, which employ quadruple anti-parallel coupled-line structures to form a novel cross-shaped resonator planar topology. The centered frequency of the single wideband bandpass filter designed for verification is located at 2.4 GHz (f 0) with a fractional bandwidth of 50%. The interaction of crossed multiple anti-coupled lines with a lowpass-loaded fan constitutes the wideband with nine transmission zeros in the 5 f 0 frequency range for improved suppression extending to 26.5 GHz (10.7 f 0) with a suppression level of 12.5 dB. Moreover, the designed prototype filter is implemented and tested with a measured minimum insertion loss of 0.9 dB. Good agreement between the measured and simulated results is attained to successfully validate the correctness of the proposed design approach.

Design of IPD-based wideband bandpass filter chips with controllable transmission zeros

ABSTRACT In this brief, two novel wideband bandpass filter (BPF) chips with independently controllable transmission zeros are proposed. BPF I uses bridge T-type highpass and lowpass structures cascaded to achieve wideband filtering. On this basis, BPF II adds three pairs of LC resonant circuits to add additional transmission zeros while retaining the lowpass structures. The analytical methods of odd-even mode and ABCD matrix to S-parameter matrix are used to analyze and calculate two designs. For validation, two prototypes of proposed BPFs in integrated passive device (IPD) have been designed, fabricated, and measured. One prototype operates at 5.3 GHz, providing a 3-dB fractional bandwidth (FBW) of 46.9%, while the other prototype operates at 4.7 GHz, providing a 3-dB FBW of 57.6%. Moreover, the two chips exhibit minimum insertion losses of 1.55 dB and 1.5 dB, respectively, while occupying compact sizes of 2.27 mm × 0.83 mm and 1.7 mm × 0.88 mm.