Bamboo Charcoal Addition Research Articles

Mechanical and Antibacterial Properties of Bamboo Charcoal/ZnO-Modified Bamboo Fiber/Polylactic Acid Composites

In this study, biodegradable bamboo fiber/PLA composites (BPCs) modified using bamboo charcoal (BC)/ZnO were prepared. The effects of BC/ZnO addition on the mechanical properties and antibacterial properties of BPCs were investigated. The chemical structure, microscopic morphology, and crystallization of the composites were analyzed using FTIR, SEM, and XRD, respectively. The results showed that in terms of mechanical strength, when the addition of BC was 2%, the tensile impact and flexural strength of the BPCs were most obviously improved, with a tensile strength of 51.6 MPa. However, when the addition of BC was more than 2%, the uneven dispersion of too much BC in the BPCs resulted in a reduction in their mechanical strength. A certain amount of ZnO did not affect the crystallinity of the BPCs. In addition, the uneven distribution of ZnO and its poor compatibility with PLA resulted in a deterioration in the tensile properties of the BPCs. In terms of antibacterial properties, when 2% ZnO was added, the BPCs had better antibacterial properties against Escherichia coli and Staphylococcus aureus, with values of 58.9% and 52.5% against both, respectively. BPC biodegradable materials with both mechanical strength and antimicrobial properties have promising medical uses.

Fracture behaviour of Sn-58Bi alloy reinforced by activated bamboo charcoal

Sn-Bi solders are considered by PV manufacturers as acceptable Pb-free alternative due to its low operating temperature and cost, despite being prone to brittleness caused by coarse Bi phases. Bamboo charcoal (BC) is a sustainable and environment-friendly resource with high surface area and its addition to Sn-Bi solder meets the requirement of a green solder, in line with environmental regulations. This study aims to improve the shear strength and reduce brittleness of the Sn-Bi solder alloy by using a sustainable reinforcement, the activated bamboo charcoal. Sn-58Bi solder paste was reinforced with 0.25, 0.50, 0.75 and 1.00 wt.% of activated BC, respectively and reflowed to create a single lap shear joint. Aging response was determined through accelerated aging at 120 °C for 7 days and 14 days. Shear strength of the joints increased as the activated BC content increased in the as-reflowed condition and there was lower degradation in shear strength for heat-aging specimens compared to pure Sn-Bi solder. No failures occurred via Mode 3 when the as-reflowed samples contained 0.50 wt.% or more of activated BC, and the 7- and 14-day heat-aged samples were free from Mode 3 failures when the activated BC composition was at 0.75 wt.% and above. Fracture surfaces showed transitions from flat and smooth surface to elongated-dimple structures even with just 0.25 wt.% of activated BC addition. While prolonged heat-aging increased cleavage presence, increasing amounts of activated BC reduced facet numbers and dimple sizes, indicating successful suppression of Bi phase segregation.

Bamboo charcoal affects soil properties and bacterial community in tea plantations.

Bamboo charcoal, a type of manufactured biochar, is produced by pyrolyzing bamboo residue under anoxic conditions. Its beneficial properties in absorption, catalyst support, and agricultural function have attracted significant attention; however, relatively few studies have examined its effects on the soil microbiota. In this study, we analyzed the effects of bamboo charcoal on soil physicochemical properties, enzymes, and microbial community structure in tea plantations and investigated the optimal amount of bamboo charcoal to be added to organic fertilizer. The results show that bamboo charcoal can further increase soil available nitrogen, total and available phosphorus and potassium, organic carbon content, pH, and urease activity. However, only the combined use of bamboo charcoal and organic fertilizer significantly increased total nitrogen, sucrase, and β-glucosidase activities in the soil. Bamboo charcoal also significantly increased the Chao1 and Shannon indices of microbiota diversity in a concentration-dependent manner. The structure of the bacterial community changed significantly after the bamboo charcoal addition, with Proteobacteria, Actinobacteria, and Firmicutes increasing and Acidobacteria decreasing. This study provides fundamental insights into the suitability of bamboo charcoal application for the ecological remediation of diseased soils.

Effects of the Addition of Bamboo Charcoal on the Water Purification Ability of Micro-organism-Supported Crystallization Type Phosphorus Removal Materials

In order to prevent water pollution in closed waters such as inner bays and lakes, it is essential to establish a method to remove phosphorus and organic substances which cause water pollution. We have tried to give organic substances removal ability to a crystallization type phosphorus remover composed of gypsum and CaCO3 by supporting useful microorganisms on the surface of the remover. In this study, the effects of loading micro-organisms derived from activated sludge on the water purification ability of the phosphorus remover were investigated. In addition, the effects of adding bamboo charcoal as a carbon source to the phosphorus remover on the adherence of microorganisms and the organic matter removal capacity were examined. The phosphorus removal material was obtained by mixing gypsum, CaCO3 and bamboo charcoal in specified volume proportions. Microorganisms were loaded on the specimens by immersing them in activated sludge for 5 days. The microorganisms supported samples by immersing in activated sludge showed higher organic matter removal capacity than the non-microbial-supported sample. Furthermore, the bamboo charcoal-added samples were able to remove organic matter in a short time than the samples without bamboo charcoal. The phosphorus removal ratio of the sample after immersing in activated sludge was almost the same as that before immersion, but when the amount of bamboo charcoal added was excessive, the phosphorus removal ratio decreased drastically. This decrease in phosphorus removal ratio would be attributed to a decrease in the content of CaCO3, which acts as a crystallization site for calcium phosphate, and to the coating of CaCO3 exposed on the surface of the phosphorus remover by the adherence of a large amount of microorganisms due to the excessive addition of bamboo charcoal.

Effect of different amounts of bamboo charcoal on properties of biodegradable bamboo charcoal/polylactic acid composites

Biodegradable composites were prepared from polylactic acid (PLA) and bamboo charcoal (BC) by melt blending and hot pressing. The effects of BC addition on the mechanical properties, water absorption, DMA, TGA, DSC, and CONE of BC/PLA composites were investigated. The microscopic morphology of the composites was analyzed by SEM. The results showed that for BC addition of 40 wt%, the mechanical strength, thermal properties, and flame retardant properties of the composites were improved compared with those of PLA, with a 2.24 % increase in flexural strength and a 1535 % increase (500 °C) in TG mass retention rate. The crystallinity increased by 129.66 %, the peak loss factor decreased by 31.15 %, the time required for combustion was delayed by 168 s, the peak heat release rate decreased by 29.40 %, the carbon residue rate detected by cone calorimetry increased by 48.50 %, and the peak mass loss rate decreased by 48.82 %. The addition of BC enhanced the crystallization capacity of PLA, and improved the thermal properties and flame retardant properties of the prepared composites. The results showed that materials prepared with a BC content of 40 wt% exhibited the best overall performance.

Bamboo charcoal fused with polyurethane foam for efficiently removing organic solvents from wastewater: experimental and simulation

The development of a multifunctional oil adsorbing material which could effectively and quickly separate oily wastewater is one of the focuses in water environment restoration. In this study, bamboo charcoal (BC) was used as an improver to modify polyurethane (PU) foam. The results of scanning electron microscope (SEM) and Fourier-transform infrared spectroscopy (FTIR) revealed that the addition of BC could effectively improve the mechanical properties of PU. The adsorption data exhibited that the BC-loaded PU (BC/PU) foam composites effectively removed seven organic solvents (OSs, including octane, petroleum ether, soybean oil, chlorobenzene, 1,2-dichloroethane, n-hexane, cyclohexane), and the maximum adsorption capacity of BC/PU was 23.6 g g−1 when BC content was 5%. The order of pseudo-second-order kinetic constants and maximum adsorption capacity of seven OSs was octane < petroleum ether < soybean oil < chlorobenzene < 1, 2-dichloroethane < cyclohexane < n-hexane. Based on the experimental data and density functional theory (DFT) simulation, the adsorption mechanism of OSs on BC/PU-5 was discussed. The EHOMO and μ of OSs calculated by DFT were highly correlated with absorption affinity (K2, Qe and Qmax). Hence, the contribution of OSs to the adsorption efficiency of BC/PU-5 may be mainly due to electron donor–acceptor (EDA) interaction and non-hydrophobic interaction. In addition, the adsorption capacity did not change significantly after repeated recycling 5 times. Overall, the prepared BC/PU foam composites could be used as a potential candidate for separating OSs in engineering applications.Graphical

Bamboo Charcoal/Poly(L-lactide) Fiber Webs Prepared Using Laser-Heated Melt Electrospinning

Although several studies have reported that the addition of bamboo charcoal (BC) to polylactide (PLA) enhances the properties of PLA, to date, no study has been reported on the fabrication of ultrafine BC/poly(L-lactide) (PLLA) webs via electrospinning. Therefore, ultrafine fiber webs of PLLA and BC/PLLA were prepared using PLLA and BC/PLLA raw fibers via a novel laser electrospinning method. Ultrafine PLLA and BC/PLLA fibers with average diameters of approximately 1 μm and coefficients of variation of 13–23 and 20–46% were obtained. Via wide-angle X-ray diffraction (WAXD) analysis, highly oriented crystals were detected in the raw fibers; however, WAXD patterns of both PLLA and BC/PLLA webs implied an amorphous structure of PLLA. Polarizing microscopy images revealed that the webs comprised ultrafine fibers with uniform diameters and wide variations in birefringence. Temperature-modulated differential scanning calorimetry measurements indicated that the degree of order of the crystals in the fibers was lower and the molecules in the fibers had higher mobilities than those in the raw fibers. Transmittance of BC/PLLA webs with an area density of 2.6 mg/cm2 suggested that the addition of BC improved UV-shielding efficiencies.

Bamboo charcoal addition enhanced the nitrogen removal of anammox granular sludge with COD: Performance, physicochemical characteristics and microbial community

The effects of different chemical oxygen demand (COD) concentrations on the anammox granular sludge with Bamboo Charcoal (BC) addition were evaluated in UASB reactor. The results showed that the average total nitrogen (TN) removal efficiency was reduced from 85.9% to 81.4% when COD concentration was increased from 50 to 150 mg/L. However, the TN removal efficiency of BC addition reactors was dramatically 3.1%–6.4% higher than that without BC under different COD concentrations. The average diameter of granular sludge was 0.13 mm higher than that without BC. The settling velocity was increased by elevated COD concentration, while the EPS and VSS/SS were increased with BC addition. The high-throughput Miseq sequencing analyses revealed that the bacterial diversity and richness were decreased under COD addition, and the Planctomycetes related to anammox bacteria were Candidatus Brocadia and Candidatus Kuenenia. The Metagenomic sequencing indicated that the abundance of denitrification related functional genes all increased with elevated COD, while the abundance of anammox related functional genes of decreased. The functional genes related to anammox was hydrazine synthase encoding genes (hzsA, hzsB and hzsB). The average relative abundance of hzs genes in the reactor with BC addition was higher than the control at COD concentrations of 50 mg/L and 150 mg/L. The functional genes of denitrification mediated by BC were higher than those without BC throughout the operation phase. It is interesting to note that BC addition greatly enriched the related functional genes of denitrification and anammox.

Development of Biodegradable Flame-Retardant Bamboo Charcoal Composites, Part II: Thermal Degradation, Gas Phase, and Elemental Analyses.

Bamboo charcoal (BC) and aluminum hypophosphite (AHP) singly and in combination were investigated as flame-retardant fillers for polylactic acid (PLA). A set of BC/PLA/AHP composites were prepared by melt-blending and tested for thermal and flame-retardancy properties in Part I. Here, in Part II, the results for differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Fourier transform infrared (FTIR), thermogravimetry-Fourier transform infrared spectrometry (TG-FTIR), X-ray diffraction (XRD), and X-ray photoelectron analysis (XPS) are presented. The fillers either singly or together promoted earlier initial thermal degradation of the surface of BC/PLA/AHP composites, with a carbon residue rate up to 40.3%, providing a protective layer of char. Additionally, BC promotes heterogeneous nucleation of PLA, while AHP improves the mechanical properties and machinability. Gaseous combustion products CO, aromatic compounds, and carbonyl groups were significantly suppressed in only the BC-PLA composite, but not pure PLA or the BC/PLA/AHP system. The flame-retardant effects of AHP and BC-AHP co-addition combine effective gas-phase and condensed-phase surface phenomena that provide a heat and oxygen barrier, protecting the inner matrix. While it generated much CO2 and smoke during combustion, it is not yet clear whether BC addition on its own contributes any significant gas phase protection for PLA.

Responses of antibiotic and heavy metal resistance genes to bamboo charcoal and bamboo vinegar during aerobic composting

The application of compost in agriculture has led to the accumulation of antibiotic resistance genes (ARGs) and heavy metal resistance genes (MRGs) in the soil environment. In this study, the response of ARGs and MRGs to bamboo charcoal (BC) and bamboo vinegar (BV) during aerobic composting was investigated. Results showed that BC + BV treatment reduced the abundances of ARGs and mobile genetic elements (MGEs) during the thermophilic period, as well as achieved the lowest rebound during the cooling period. BC + BV promoted the growth of Firmicutes, thereby facilitating the thermophilic period of composting. The rebound of ARGs and MGEs can be explained by increasing the abundance of Actinobacteria and Proteobacteria at the end of composting. Composting reduced the abundances of MRGs comprising pcoA, tcrB, and cueO, whereas cusA and copA indicated the selective pressure imposed by heavy metals on bacteria. The fate of ARGs was mainly driven by MGEs, and heavy metals explained most of the variation in MRGs. Interestingly, nitrogen conversion also had an important effect on ARG and MRG profiles. Our current findings suggest that the addition of BC + BV during compost preparation is an effective method in controlling the mobility of ARGs and MRGs, thereby reducing the environmental problems.

Mechanical Properties of Bamboo Charcoal (BC)/Poly(Lactic) Acid (PLA) Composites

The influence of bamboo charcoal (BC) in Poly (lactic) acid (PLA) matrix as masterbatch was studied on mechanical 40:60, 50:50 and 60:40 of masterbatch. BC MBs were diluted at 1 phr, 3 phr, and 5 phr. BC showed even distribution in PLA matrix; however,, it decreased compatibility in the matrix. The infusion of BC in PLA matrix enhanced the tensile modulus; however, there was a reduction in the tensile strength and the elongation at break. It could also be ascertained that there is no signification difference in the hardness of BC/PLA composites compared with neat PLA. The addition of BC slightly decreased shear viscosity of the composites. The optimal BC content in the composites was found to be 2.82wt.% (5 phr 60:40).

Preparation and Characterization of PVA Alkaline Solid Polymer Electrolyte with Addition of Bamboo Charcoal.

Natural bamboo charcoal (BC) powder has been developed as a novel filler in order to further improve performances of the polyvinyl alcohol (PVA)-based alkaline solid polymer electrolyte (ASPE) by solution casting method. X-ray diffraction patterns of composite polymer electrolyte with BC revealed the decrease in the degree of crystallinity with increasing content of BC. Scanning electron microscopy images showed pores on a micrometer scale (average diameter about 2 μm) distributed inside and on the surface of the membranes, indicating a three-dimension network formed in the polymer framework. The ionic conductivity was measured by the alternating-current (AC) impedance method, and the highest conductivity value of 6.63 × 10−2 S·cm−1 was obtained with 16 wt % of BC content and mKOH:mPVA = 2:1.5 at 30 °C. The contents of BC and KOH could significantly influence the conductivity. The temperature dependence of the bulk electrical conductivity displayed a combination of Arrhenius nature, and the activation energy for the ion in polymer electrolyte has been calculated. The electrochemical stability window of the electrolyte membrane was over 1.6 V. The thermogravimetric analysis curves showed that the degradation temperatures of PVA-BC-KOH ASPE membranes shifted toward higher with adding BC. A simple nickel-hydrogen battery containing PVA-BC-KOH electrolyte membrane was assembled with a maximum discharge capacity of 193 mAh·g−1.

Mechanical, electrical, and thermal properties of highly filled bamboo charcoal/ultra‐high molecular weight polyethylene composites

Highly filled bamboo charcoal (BC)/ultra‐high molecular weight polyethylene (UHMWPE) composites were prepared using extrusion and hot‐compression molding methods. The addition of BC remarkably improved the tensile properties of UHMWPE composites. When the BC content reached 70 wt%, the tensile strength and Young's modulus rose from 28.0 and 326.6 MPa for the neat UHMWPE to 128.9 and 2,027.7 MPa, increasing by 360 and 520%, respectively. The incorporation of BC also significantly improved the creep resistance, especially at high temperature. The creep strains of the composites with 60, 70 and 80 wt% were reduced by 70.1, 78.3, and 85.2% compared to the neat UHMWPE at 80°C, respectively. To understand the mechanism, the Burger's model was employed to illustrate the influence of BC on the creep performance of the polymer composites. The addition of BC also increased the electrical conductivity of the composites: the composite with 80 wt% BC had a conductivity of 0.53 S/cm. Moreover, the thermal stability of BC/UHMWPE composites improved apparently with the increased charcoal loading. POLYM. COMPOS., 39:E1858–E1866, 2018. © 2018 Society of Plastics Engineers

Size effect of charcoal particles on the properties of bamboo charcoal/ultra‐high molecular weight polyethylene composites

ABSTRACTThis study was aimed at examining the size effect of charcoal particles on the properties of bamboo charcoal (BC)/ultra‐high molecular weight polyethylene (UHMWPE) composites. Four types of BC with various particle sizes were mixed with UHMWPE using a twin‐screw extruder. It was found that the melting temperature and crystallinity of the composites were slightly decreased with the addition of BC. The incorporation of BC remarkably improved the tensile properties and creep resistance of UHMWPE, and the particle size of BC strongly affected the properties of BC/UHMWPE composites. The BC with lowest particle size exhibited best reinforcement, where the tensile strength and Young's modulus were increased by 385% and 517% compared with neat UHMWPE. The composites with 70 wt % BC possessed conductivities of 16.8, 14.1, 13.5, and 10.9 S/m. The storage modulus and glass transition temperature of the composites also increased with the addition of BC. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45530.

Effects of bamboo charcoal on fouling and microbial diversity in a flat-sheet ceramic membrane bioreactor

Membrane fouling is a problem in full-scale membrane bioreactors. In this study, bamboo charcoal (BC) was evaluated for its efficacy in alleviating membrane fouling in flat-sheet membrane bioreactors treating municipal wastewater. The results showed that BC addition markedly improved treatment performance based on COD, NH4+-N, total nitrogen, and total phosphorus levels. Adding BC slowed the increase in the trans-membrane pressure rate and resulted in lower levels of soluble microbial products and extracellular polymeric substances detected in the flat-sheet membrane bioreactor. BC has a porous structure, and a large quantity of biomass was detected using scanning electron microscopy. The microbial community analysis results indicated that BC increased the microbial diversity and Aminomonas, Anaerofustis, uncultured Anaerolineaceae, Anaerolinea, and Anaerotruncus were found in higher abundances in the reactor with BC. BC addition is an effective method for reducing membrane fouling, and can be applied to full-scale flat-sheet membrane bioreactors to improve their function.

Enhancement of Photocatalytic and Antibacterial Activities of ZnO:Ag Nanopowders Through the Addition of Bamboo Charcoal: An Efficient Natural Adsorbent

This research article explains the removal of methylene blue (MB) and malachite green (MG) from aqueous solution using adsorption/photodegradation activity of ZnO:Ag/bamboo charcoal (BC) nanocomposite. In addition, the antibacterial studies of the prepared samples were tested against Staphylococcus aureus (S. aureus) Gram-positive and Escherichia coli (E. coli) Gram-negative bacteria by the well diffusion method. The ZnO:Ag/BC nanocomposite exhibits superior photocatalytic activity compared with ZnO:Ag. Remarkable degradation efficiencies of 93.95% (MB) and 95.75% (MG) were recorded for ZnO:Ag/BC nanocomposite after 45 min. The degradation process follows a pseudo-first-order kinetics. The rate constant of ZnO:Ag/BC nanocomposite is two times greater than that of pristine ZnO nanopowder for the degradation of MB dye, while for MG dye degradation, it is three times. It is found that the ZnO:Ag/BC nanocomposite shows a higher rate of dye removal due to excellent adsorbing properties of bamboo charcoal (BC). The ZnO:Ag/BC nanocomposite showed better antibacterial properties compared to ZnO:Ag. In this study, the samples were prepared using a simple and low-cost soft chemical route and they were characterized by optical, structural, surface morphological, antibacterial and photocatalytic properties. These characterization studies substantiate the discussions on the photocatalytic and antibacterial activities of the synthesized samples.

An enhanced anaerobic membrane bioreactor treating bamboo industry wastewater by bamboo charcoal addition: Performance and microbial community analysis

In this study, two anaerobic membrane bioreactors (AnMBRs) were operated for 150days to treat bamboo industry wastewater (BIWW), and one of them was enhanced with bamboo charcoal (B-AnMBR). During the steady period, average chemical oxygen demand (COD) removal efficiencies of 94.5±2.9% and 89.1±3.1% were achieved in B-AnMBR and AnMBR, respectively. The addition of bamboo charcoal (BC) increased the amount of biomass and improved the performance of the systems. A higher biogas production and methane yield were also observed in B-AnMBR. Regarding the issue of membrane fouling, BC lowered the soluble microbial product (SMP) content by approximately 62.73mg/L and decreased the membrane resistance, thereby mitigating membrane fouling. Analysis of the microbial communities demonstrated that BC increased the microbial diversity and promoted the activity of Methanosaeta, Methanospirillum, and Methanobacterium, which are dominant in methane production.

Enhanced antibiotic removal by the addition of bamboo charcoal during pig manure composting

The addition of bamboo charcoal during pig manure composting enhanced the depletion of antibiotics, ciprofloxacin, chlorotetracycline, and norfloxacin.

Use of bamboo charcoal reduced the cultivated anammox seed sludge dosage during the start-up period

Bamboo charcoal (BC) was used in an anaerobic ammonium oxidation (anammox) process used for synthetic wastewater treatment with the aim of evaluating its use as a biocarrier to reduce the cultivated anammox seed sludge (CASS) dosage. The CASS dosage was reduced by more than 50% after BC was added to the anammox reactor. Furthermore, the time required for the start-up of the anammox reactor under the experimental conditions was reduced about six weeks after the addition of BC. A genetic analysis of the organisms in the granular bed revealed an abundance of Kuenenia stuttgartiensis and uncultured bacterium clone KIST-JJY001 enriched in the reactor.

Improving Anammox start-up with bamboo charcoal

Three Upflow Anaerobic Sludge Blanket (UASB) reactors were compared for Anammox enrichment using synthetic wastewater with Spherical Plastic (SP) and Bamboo Charcoal (BC) addition, and without carrier (CK). After four months of operation, the Anammox activity occurred in all reactors allowing continuous removal of ammonium and nitrite. Ammonium and nitrite removal efficiencies were all higher than 98% in steady phase with the effluent concentrations below 1mgL−1. The start-up time could be shortened from 117 to 97d in CK and SP reactor to 85d in BC amendment reactor. Quantitative PCR (q-PCR) analyses indicated a significant increase in the number of Anammox bacteria in BC amended reactor as compared with CK and SP during the entire start-up periods. The copy numbers of Anammox of 16SrRNA gene in the reactor with BC amendment could reach up to 6×109copiesg−1 Volatile Suspended Solids, around 22.5times and 12.3times greater than that in CK and SP reactor, respectively. BC addition could accelerate the start-up of Anammox and significantly increase the Anammox bacteria number.