Ballistic Gelatin Research Articles

Three-Dimensional Modeling of Firearm Injuries in Forensic Medicine

Introduction. Forensic medical investigations, including illustration, evidence collection, and expert conclusion preparation, have faced significant challenges in recent years. One of the primary challenges for Ukraine’s forensic medical service today is the examination of firearm-related injuries, necessitating substantial improvements to traditional methodologies. The study aimed to develop a methodology for the three-dimensional spatial reconstruction of firearm injuries. Methods. An automatic pistol CZ83 of medium caliber, manufactured in the Czech Republic and chambered for 7.65x17 mm ammunition, was used in the study. Roma Plastilina No. 1 ballistic gelatin, produced in the USA, served as the target and reproducing material for controlled ballistics tests. The experiments included 15 shots, during which the main morphological elements of skin injury, the subcutaneous adipose tissue, and the wound channel at the entry, middle, and exit points were studied. These were photographed, analyzed using photogrammetry, and converted into a three-dimensional format with the graphic editors Agisoft PhotoScan and 3Ds Max. Results. Measurements of all parameters obtained through classical methods differed significantly (p<0.05) from those obtained using 3D modeling. However, Cohen’s d values indicated that the differences were very small for defect size measurements, small for the abrasion ring and wound channel diameter across all sections, and medium for the entry wound diameter. Conclusions. The developed methodology for three-dimensional modeling allows for the accurate recording of the main morphometric parameters of firearm injuries, making it a viable alternative to traditional measurement methods.

Distribution of bone fragments in angled shots: an experimental study conducted on composite models containing artificial bone plates.

In conventional gunshot injuries to targets containing bone the resulting osseous fragments do not precede but follow the bullet on its further way through adjacent soft tissues. The term "secondary projectiles" for the particles does not appear to be appropriate since they are not believed to have enough energy necessary for creating their own wound channels away from the temporary cavity. Former studies have shown that in angled shots to glass panes the bulk of splinters does not follow the bullet's trajectory: The majority of the glass fragments, especially the larger ones, move at right angles to the pane shot through. The aim of the presented study was to examine whether osseous fragments behave like glass splinters in angled shots to flat synthetic bone. In this context, it should also be assessed, whether the bone fragments might act as secondary projectiles in rare cases. To answer these questions, test shots were fired to composite models consisting of flat synthetic bone and ballistic gelatin. Pistol cartridges 9mm Luger were used to fire the shots which were video-documented with a high-speed camera. Afterwards, the composite models underwent CT examination and macroscopic inspection. Video-documentation revealed that the larger bone particles from the perforation site move at a roughly right angle from the osseous sheet into the gelatin, causing an eccentric bulge of the temporary cavity. The smaller bone fragments were also lodged along the bullet's path, predominantly in the cracks radiating from the permanent wound channel.

Monte Carlo modeling and simulation of a new 3D printed phantom for WBC calibration with ballistic gel as a tissue substitute

Whole-body counter (WBC) systems are used for in vivo monitoring in occupational internal dosimetry, typically calibrated using physical anthropomorphic phantoms. Our research group previously 3D-printed the Reference Female Phantom for Internal Dosimetry (RFPID) without internal organs specifically designed for WBC calibration. The RFPID and it is intended to fill it homogenously with ballistic gel, which is commonly used as a tissue equivalent in ballistic studies. However, comprehensive characterization of its physicochemical properties and radiological behavior as a tissue surrogate for dosimetry is limited. This study aims to evaluate the suitability of ballistic gel as a tissue substitute for physical phantoms in WBC system calibration and to analyze the RFPID as a model for WBC calibration. Ballistic gel tests determined its density and attenuation coefficients, comparing it to muscle, water, and PMMA. The RFPID was modeled and simulated using MCNP6.2 code and placed in an in vivo monitoring system using an 8”x4″ NaI(Tl) scintillator detector previously validated. The simulations were repeated with the RCP_AF of ICRP-110. Results indicate that ballistic gel has a density approximately 6% different from muscle and shows similar linear attenuation coefficients to muscle at intermediate and high energy levels (186–2200 keV). Simulations revealed a disparity of less than 9% in counting efficiency between RFPID and RCP_AF for energies from 100 to 3000 keV, confirming the phantom's suitability for WBC calibration and ballistic gel's viability as a tissue surrogate in internal dosimetry.

Experimental studies on penetration process of high-speed water-jet into ballistic gelatin

To reveal the penetration mechanism and present the penetration characteristics of high-speed micro-jet with injection volume larger than 0.3 mL into soft tissue, the present study conducted experimental research on high-speed water-jet penetration into ballistic gelatin. The free jet dynamics of an air-powered needle-free injector that can emit up to 1.27 mL of liquid at once and the penetration dynamics were visualized to reveal the details of the penetration process. In the early unstable stage, the jet is emitted in the form of pulses, and the first jet pulse can rapidly generate an initial slender channel in gelatin in a very short time. In the subsequent stable stage, energy input produces dispersion and further increases the penetration depth slowly. Changing the driving pressure by the power source mainly changes the penetration depth increment by dispersion; while changing the nozzle diameter mainly affects the penetration depth in the initial stage. The central position of the dispersion area in the injection direction was firstly defined in the present work and it was found that an approximate linear relationship between this position and the maximum penetration depth exits for different nozzle diameters and driving pressures when injecting the same liquid dose. These research results can provide a basis for a thorough understanding of the penetration characteristics of high-speed micro-jet with injection volume larger than 0.3 mL into soft tissue, as well as the design and operation of the air-powered needle-free injector.

A Multicomponent Microneedle Patch for the Delivery of Meloxicam for Veterinary Applications.

This study evaluates the use of poly(vinyl alcohol), collagen, and chitosan blends for developing a microneedle patch for the delivery of meloxicam (MEL). Results confirm successful MEL encapsulation, structural integrity, and chemical stability even after ethylene oxide sterilization. Mechanical testing indicates the patch has the required properties for effective skin penetration and drug delivery, as demonstrated by load-displacement curves showing successful penetration of pig ear surfaces at 3N of normal load. In vitro imaging confirms the microneedle patch penetrates the pig's ear cadaver skin effectively and uniformly, with histological evaluation revealing the sustained presence and gradual degradation of microneedles within the skin. Additionally, in vitro drug diffusion experiments utilizing ballistic gel suggest that microneedles commence dissolution almost immediately upon insertion into the gel, steadily releasing the drug over 24 h. Furthermore, the microneedle patch demonstrates ideal drug release capabilities, achieving nearly 100% release of meloxicam content from a single patch within 18 h. Finally, in vivo studies using pigs demonstrate the successful dissolution and transdermal drug delivery efficacy of biodegradable microneedle patches delivering meloxicam in a porcine model, with over 70% of microneedles undergoing dissolution after 3 days. While low detectable meloxicam concentrations were observed in the bloodstream, high levels were detected in the ear tissue, confirming the release and diffusion of the drug from microneedles. This work highlights the potential of microneedle patches for controlled drug release in veterinary applications.

Three-dimensional visualization of gunshot cavities in ballistic gelatine with computed tomography – A forensic ballistics case study

Three-dimensional (3D) imaging, primarily computed tomography (CT), has proven valuable in the documentation and analysis of gunshot injuries. Explicit visualization of findings may play a pivotal role in judicial settings. This forensic ballistics case study aimed to examine the potential of CT-based 3D reconstruction to digitally visualize gunshot cavities in ballistic gelatine. Three .30 caliber bullets of different types (full metal jacket, soft point, and expanding monolithic) were fired into standardized blocks of 10% ballistic gelatine. The blocks underwent CT scanning with clinical equipment. Gelatine and air were segmented from the CT data using an open-source software. 3D reconstruction views of the segmented gelatine and air components were created. The gunshot cavities were clearly observed in both gelatine and air segmentation. The differences in cavitation between bullet types were evident in both reconstruction approaches, although gelatine segmentation produced higher resolution of small details. The obvious benefit of digital reconstruction was the ability to freely tilt and rotate the 3D images, with the possibility of taking measurements manually or automatically from any plane. Moreover, all the data can be stored for future analysis. This study introduces a preliminary method for digital visualization and documentation of gunshot cavitation in ballistic gelatine, to be fine-tuned and implemented for research purposes and routine practice in forensic institutions.

Evaluation of synthetic clear gelatin as an acceptable surrogate for low-velocity penetrating impacts using the depth of penetration calibration standard

Ballistic gelatin has been extensively used in ballistics research for decades, but calibration standards were established on limited datasets, and only few studies have attempted to recreate these experiments with biological tissues. Recent studies have demonstrated better biofidelity with 20% ordnance ballistic gelatin, but researchers have discredited the use of synthetic gelatin claiming different behavior than ordnance gelatin. To investigate the use of synthetic clear gelatin as an acceptable surrogate of biological tissue, depth of penetration was compared between low-velocity impacts of various projectiles into porcine tissue (n = 192), post-mortem human subjects (n = 29), and Clear Ballistics synthetic gelatin (n = 39). The predicted depth of penetration of the 0.177" steel BB (38.1 mm) was consistent with the manufacturer's calibration standard (31.75–44.45 mm) and within calibration bounds of recently proposed empirical equations. Compared to impacts in biological tissue, synthetic gelatin demonstrated the least variability in depth of penetration (R2 = 0.96). Using ANCOVA, velocity was a significant covariate (p < 0.001), and there were no significant differences in normalized depth of penetration over density between porcine tissue, post-mortem human subjects, and 20% synthetic gelatin (p = 0.22). Ultimately, this study confirmed the use of 20% synthetic gelatin as an acceptable tissue simulant using standard calibration methods for use in future ballistic studies.

Terminal ballistics performance of 9 × 19mm cartridges in 10% ballistic gelatin: FBI Protocol based analysis of Brazilian-made law enforcement ammunition.

Understanding that a projectile entering the human body can cause damage or destruction to live tissues through a variety of wounding mechanisms - permanent cavity, temporary cavity, and fragmentation - is crucial for researching terminal ballistics and understand the patterns of gunshot wound configuration. The present work tested four different types of ammunition in caliber 9 × 19mm (Full Metal Jacketed, Gold Hex, Copper Bullet Tactical and Bonded), using ballistic gelatin at 10% as soft tissue surrogate. The tests were based on the Federal Bureau of Investigation Protocol and included shots through bare gelatin, heavy clothing, plywood, steel sheets and auto glass. As a comparison parameter, the American-made Federal™ HST, used by several law enforcement agencies in the USA, was also tested in the same conditions. The Full Metal Jacketed cartridge had a uniform performance throughout the experiment, showing high penetration levels and no expansion, as expected. Gold Hex demonstrated a strong tendency to fragment with low levels of penetration and weight retention. Copper Bullet Tactical did not achieve the 12" minimum penetration in the soft barrier phases but expanded aggressively. Finally, Bonded only failed to achieve the 12" mark of penetration in phase 5 (auto glass), the hardest barrier in the whole Protocol. Tested for comparison purposes, Federal HST showed aggressive expansion in the initial phases (over 100%), after surpassing the 12" threshold. The study concluded that heavier projectiles (CBC Bonded and Federal HST) performed better than lighter and faster bullets in terms of terminal ballistics.

Visco-hyperelastic material model fitting to experimental stress–strain curves using a genetic algorithm and its application to soft tissue simulants

Ballistic impacts on human thorax without penetration can produce severe injuries or even death of the carrier. Soft tissue finite element models must capture the non-linear elasticity and strain-rate dependence to accurately estimate the dynamic human mechanical response. The objective of this work is the calibration of a visco-hyperelastic model for soft tissue simulants. Material model parameters have been calculated by fitting experimental stress–strain relations obtained from the literature using genetic algorithms. Several parametric analyses have been carried out during the definition of the optimization algorithm. In this way, we were able to study different optimization strategies to improve the convergence and accuracy of the final result. Finally, the genetic algorithm has been applied to calibrate two different soft tissue simulants: ballistic gelatin and styrene–ethylene–butylene–styrene. The algorithm is able to calculate the constants for visco-hyperelastic constitutive equations with high accuracy. Regarding synthetic stress–strain curves, a short computational time has been shown when using the semi-free strategy, leading to high precision results in stress–strain curves. The algorithm developed in this work, whose code is included as supplementary material for the reader use, can be applied to calibrate visco-hyperelastic parameters from stress–strain relations under different strain rates. The semi-free relaxation time strategy has shown to obtain more accurate results and shorter convergence times than the other strategies studied. It has been also shown that the understanding of the constitutive models and the complexity of the stress–strain objective curves is crucial for the accuracy of the method.

Fun with electricity: A novel ballistics gelatin model with LED tracking for ultrasound needle guidance.

Use of ultrasound (US) for procedural needle guidance can improve success rates, safety, and accuracy. Often, training is performed on task trainers, which can be prohibitively expensive. Determining undesired needle placement is difficult when the needle is poorly visualized with US. Currently available simulation phantoms cannot provide real-time feedback on the location of needle placement. The primary objective was to develop and determine feasibility of a low-cost simulation phantom with an internal circuit and LED light system to determine when a needle contacts internal structures. We also aimed to determine whether its use was associated with increased comfort level. Emergency medicine (EM) residents (PGY-1 to PGY-3) performed in-plane and out-of-plane US needle guidance using homemade phantoms. Comfort levels were assessed by pre- and post intervention survey. Outcomes were measured on Likert scale (minimum = 1, maximum = 5). The primary outcome was change in confidence markers before and after the simulation task. Secondary outcomes were survey results of comparisons of these models to prior training experiences on simulators and humans. All EM residents (30) in our program were invited to participate. Twenty participants enrolled and completed the study. In the primary outcome, median comfort with out-of-plane and in-plane guidance increased after using the model but was more pronounced for out-of-plane guidance. On a posttest survey, residents rated the models overall very similar to prior experience on simulators (median 5/5 [IQR 4.0-5.0]) and moderately similar to humans (median 3/5 [IQR 3.0-4.0]). We created a low-cost ballistic gelatin phantom with an internal electric needle guidance system. Use of the phantom for training was associated with increased learner comfort with the procedure. Learners rated the characteristics of the phantom as similar to higher-cost commercial equipment and humans.

Comparison of curved and straight tip radiofrequency cannula deflection in a ballistic model

BackgroundPercutaneous pain and spine procedures play an important diagnostic and therapeutic role in the treatment of various pain diagnoses. Accurate placement of needles or cannulae during these procedures is paramount to the success of these procedures. ObjectiveThe purpose of this study is to examine and quantify the amount of deflection of radiofrequency cannulae based on curved tip versus no curved tip, using a ballistic gel tissue simulant. Materials and methodsSix different types of cannulae commonly used for spinal and peripheral nerve ablations were selected, including 18, 20, and 22 gauge curved and straight radiofrequency cannulae. Ballistic gel samples were made in molds of 40 mm and 80 mm. Each cannula was mounted in a drill press to ensure accurate trajectory. ResultsCurved RFA cannula had increased deflection when compared to straight cannula for 18-, 20-, and 22-gauge cannulae at a depth of 40 mm. Curved RFA cannula had increased deflection when compared to straight cannula for 20- and 22-gauge cannulae at a depth of 80 mm. Overall, the mean deflection for a curved cannula increased 1.9x for 20-gauge cannulae and 2.5x for 22-gauge cannulae when compared to a straight cannula. ConclusionsFor interventionalists, understanding the effects of needle or cannula shape is crucial for accurate placement. When a procedure requires additional steerability, additional deflection up to 2.5x obtained by placing a bend in the needle or cannula tip should be considered.

Quantification of metallic artifact on CT associated with titanium pedicle screws.

In dogs undergoing vertebral column stabilization, post-operative computed tomography (CT) evaluates implant placement. The impact on the interpretation of metallic artifact associated with titanium implants in dogs remains to be established. Our objective was to quantify metallic artifact on CT associated with titanium pedicle screws. The study design included an in vitro model and a retrospective review of 11 dogs with vertebral column stabilization. Twenty four titanium pedicle screws (6 each: 2.0 mm, 2.7 mm, 3.5 mm, and 4.5 mm) were inserted into a 20% ballistic gel, and CT scan of the construct was performed. Three blinded raters used a bone window to measure the maximum width (effective size) of each screw, one rater measured effective size using an ultrawide window and 45 titanium pedicle screws (3×2.0 mm, 5×2.7 mm, 30×3.5 mm, and 7×4.5 mm) in 11 clinical cases. Effective size measurements were compared to actual screw sizes. The effective size was 26.9-43.8%, 9.2-18.5%, and 21.1-30.5% larger than the actual size for the in vitro system (bone window), in vitro system (ultrawide window), and clinical cases, respectively. The mean gross difference for the in vitro measurements varied by implant size (p < 0.001) and was positively correlated with implant size (r = 0.846), but the mean percentage difference was negatively correlated with implant size (p < 0.001). Overestimation was larger for the in vitro model bone window compared to the ultrawide window (p < 0.001) and clinical cases (p = 0.001). Metallic artifact associated with titanium pedicle screws on CT resulted in an overestimation of screw size. This information might aid in the interpretation of implant placement on post-operative imaging.

Development of a flexible liver phantom for hepatocellular carcinoma treatment planning: a useful tool for training & education

PurposeHepatocellular carcinoma (HCC) is one of the most common types of liver cancer that could potentially be surrounded by healthy arteries or veins that a surgeon would have to avoid during treatment. A realistic 3D liver model is an unmet need for HCC preoperative planning.MethodsThis paper presents a method to create a soft phantom model of the human liver with the help of a 3D-printed mold, silicone, ballistic gel, and a blender.ResultsFor silicone, the elastic modulus of seven different ratios of base silicone and silicone hardener are tested; while for ballistic gel, a model using 20% gelatin and 10% gelatin is created for the tumor and the rest of the liver, respectively. It is found that the silicone modulus of elasticity matches with the real liver modulus of elasticity. It is also found that the 10% gelatin part of the ballistic gel model is an excellent emulation of a healthy human liver.ConclusionThe 3D flexible liver phantom made from a 10% gelatin-to-water mixture demonstrates decent fidelity to real liver tissue in terms of texture and elasticity. It holds significant potential for improving medical training, preoperative planning, and surgical research. We believe that continued development and validation of such models could further enhance their utility and impact in the field of hepatobiliary treatment planning and education.

Experimental Tests on External and Terminal Ballistics of Different Types of Projectiles Fired From .38 SPL Caliber Cartridges and Study of Permanent Cavitation in Anatomical Modeling With 10% Ballistic Gelatin.

The present study investigated the main morphological differences between the permanent cavities formed by 4 different types of projectiles fired from .38 SPL caliber cartridges in blocks of 10% ballistic gelatin with standardized formulation (Federal Bureau of Investigation Protocol), all fired from the same distance and from the same firearm, associated with its performances in external and terminal ballistics. The velocity or the mass presented by a firearm projectile will not always be solely responsible for the final configuration of the permanent cavity, in which the projectile design, for example, is an equally important element. Each type of projectile tested in the present work generated a different kind of permanent cavity, but they also varied in velocity (m/s) and energy (J). The use of 10% ballistic gelatin in scientific research that seeks to investigate the external and terminal ballistics of projectiles can contribute to the practice of professionals working either in forensic pathology or applied ballistics scenarios, as they can experimentally simulate the events that can occur in the tissues of victims inflicted by gunshot wounds, which also allows important applications in the medical, commercial, civil, and military sectors that deal with products and technologies related to the human body.

Ballistic Gels in Experimental Fracture Setting.

Biomechanical tests typically involve bending, compression, or shear stress, while fall tests are less common. The main challenge in performing fall tests is the non-reproducible directionality of bone when tested with soft tissue. Upon removal of the soft tissue, the explanted bone's resistance to impact diminishes. Therefore, ballistic gels can fix specimens in reproducible directions and simulate periosteal soft tissue. However, the use of ballistic gels in biomechanical studies is neither standardized nor widespread. This study aimed to optimize a ballistic gel consistency that mimics the upper thigh muscle in sheep. Our results suggest a standardized and flexible evaluation method by embedding samples in ballistic gel. Compression tests were conducted using cylindrical pieces of gluteal muscle from sheep. Various compositions of agarose and gelatin mixtures were tested to achieve a muscle-like consistency. The muscle-equivalent ballistic gel was found to consist of 29.5% gelatin and 0.35% agarose. Bones remained stable within the ballistic gel setup after freeze-thaw cycles between -20 °C and +20 °C. This method reduces the variability caused by muscle and improves storage quality, allowing for tests to be conducted under consistent conditionsBallistic gels of agarose and gelatin are suitable for bone fracture models. They have muscle-like strength, fix fractures simultaneously, are inexpensive to produce, and can be stored to allow repeated measurements of the same object with changing questions.

Development of a Novel Soft Tissue Measurement Device for Individualized Finite Element Modeling in Custom-Fit CPAP Mask Evaluation

PurposeIndividual facial soft tissue properties are necessary for creating individualized finite element (FE) models to evaluate medical devices such as continuous positive airway pressure (CPAP) masks. There are no standard tools available to measure facial soft tissue elastic moduli, and techniques in literature require advanced equipment or custom parts to replicate.MethodsWe propose a simple and inexpensive soft tissue measurement (STM) indenter device to estimate facial soft tissue elasticity at five sites: chin, cheek near lip, below cheekbone, cheekbone, and cheek. The STM device consists of a probe with a linear actuator and force sensor, an adjustment system for probe orientation, a head support frame, and a controller. The device was validated on six ballistics gel samples and then tested on 28 subjects. Soft tissue thickness was also collected for each subject using ultrasound.ResultsThickness and elastic modulus measurements were successfully collected for all subjects. The mean elastic modulus for each site is Ec = 53.04 ± 20.97 kPa for the chin, El = 16.33 ± 8.37 kPa for the cheek near lip, Ebc = 27.09 ± 11.38 kPa for below cheekbone, Ecb = 64.79 ± 17.12 kPa for the cheekbone, and Ech = 16.20 ± 5.09 kPa for the cheek. The thickness and elastic modulus values are in the range of previously reported values. One subject’s measured soft tissue elastic moduli and thickness were used to evaluate custom-fit CPAP mask fit in comparison to a model of that subject with arbitrary elastic moduli and thickness. The model with measured values more closely resembles in vivo leakage results.ConclusionOverall, the STM provides a first estimate of facial soft tissue elasticity and is affordable and easy to build with mostly off-the-shelf parts. These values can be used to create personalized FE models to evaluate custom-fit CPAP masks.

Three-Dimensional-Digital Image Correlation Methodology for Kinematic Measurements of Non-Penetrating Blunt Impacts.

Blunt force trauma remains a serious threat to many populations and is commonly seen in motor vehicle crashes, sports, and military environments. Effective design of helmets and protective armor should consider biomechanical tolerances of organs in which they intend to protect and require accurate measurements of deformation as a primary injury metric during impact. To overcome challenges found in velocity and displacement measurements during blunt impact using an integrated accelerometer and two-dimensional (2D) high-speed video, three-dimensional (3D) digital image correlation (DIC) measurements were taken and compared to the accepted techniques. A semispherical impactor was launched at impact velocities from 14 to 20 m/s into synthetic ballistic gelatin to simulate blunt impacts observed in behind armor blunt trauma (BABT), falls, and sports impacts. Repeated measures Analysis of Variance resulted in no significant differences in maximum displacement (p = 0.10), time of maximum displacement (p = 0.21), impact velocity (p = 0.13), and rebound velocity (p = 0.21) between methods. The 3D-DIC measurements demonstrated equal or improved percent difference and low root-mean-square deviation compared to the accepted measurement techniques. Therefore, 3D-DIC may be utilized in BABT and other blunt impact applications for accurate 3D kinematic measurements, especially when an accelerometer or 2D lateral camera analysis is impractical or susceptible to error.

Skin simulants for wound ballistic investigation – an experimental study

Gunshot wound analysis is an important part of medicolegal practice, in both autopsies and examinations of living persons. Well-established and studied simulants exist that exhibit both physical and biomechanical properties of soft-tissues and bones. Current research literature on ballistic wounds focuses on the biomechanical properties of skin simulants. In our extensive experimental study, we tested numerous synthetic and natural materials, regarding their macromorphological bullet impact characteristics, and compared these data with those from real bullet injuries gathered from medicolegal practice. Over thirty varieties of potential skin simulants were shot perpendicularly, and at 45°, at a distance of 10 m and 0.3 m, using full metal jacket (FMJ) projectiles (9 × 19 mm Luger). Simulants included ballistic gelatine at various concentrations, dental silicones with several degrees of hardness, alginates, latex, chamois leather, suture trainers for medical training purposes and various material compound models. In addition to complying to the general requirements for a synthetic simulant, results obtained from dental silicones shore hardness 70 (backed with 20 % by mass gelatine), were especially highly comparable to gunshot entry wounds in skin from real cases. Based on these results, particularly focusing on the macroscopically detectable criteria, we can strongly recommend dental silicone shore hardness 70 as a skin simulant for wound ballistics examinations.

LUFT: A low-frequency ultrasound tomography system designed for lung imaging.

Pulmonary imaging with ultrasound in the conventional MHz range suffers from significant artifacts, as the high frequency acoustic waves primarily reflect off of the lung pleura with little to no penetration through the lung tissue. Furthermore, B-mode ultrasound images are difficult to interpret and require a skilled technician to obtain. Motivated by the finding that acoustic frequencies in the kHz penetrate lung tissue, a low-frequency tomographic ultrasound system is presented. A Verasonics Vantage 64 low-frequency ultrasound system is programmed to work with a novel low-frequency Tonpilz transducers set arranged in a circular array on a belt. After signal processing, a time-of-flight (TOF) tomographic reconstruction algorithm with refraction correction is applied to estimate the sound speed in the plane of the transducer array. Data were collected on experimental phantoms made of ballistic gel containing targets of varying sound speeds, and reconstructions TOF were computed. Results demonstrate that the low-frequency ultrasound tomography system effectively detects targets in an experimental phantom with the ability to resolve multiple targets and distinguish between targets of high and low sound speed compared to the background medium.

Development and Implementation of a Basic Veterinary Ultrasound Curriculum.

Diagnostic ultrasound is an important imaging modality in veterinary medicine. Surveys of veterinarians suggest that ultrasound is a desired clinical competence and that new graduates are expected to practice basic ultrasound skills. This report describes the development and implementation of a basic ultrasound training program in the core curriculum at Iowa State University College of Veterinary Medicine (ISU-CVM). A multidisciplinary team of ISU-CVM faculty created and delivered a basic ultrasound training program consisting of two lectures and two hands-on laboratories incorporated into a second-year core course, utilizing ballistic gel and silicone phantoms as well as live-dog scanning. The focus of training was on basic image acquisition, image optimization, and regional sonographic anatomy of the canine abdomen. Students were surveyed at 6-month intervals during program implementation. Survey data from graduating students, alumni, and employers were also analyzed. The program was successfully implemented and was well-received by all key stakeholders. Alumni and employer surveys reinforced the importance of basic ultrasound skills as a competency for new graduates. Student survey data revealed that satisfaction with ultrasound training increased after implementation of the program, as did students' perception of their skill level in individual ultrasound competencies. Student surveys also identified ways to enrich the program by providing additional opportunities for ultrasound practice in subsequent laboratory courses and clinical rotations. This report summarizes lessons learned during development of basic ultrasound training in the core curriculum at ISU-CVM and can serve as a reference for other institutions considering similar programs.