Atomic Force Microscopy Studies Research Articles

Evaluation of PEGylation efficacy of curcumin-loaded nanoemulsions using complementary methods to assess protein interactions and physicochemical properties

Nanoemulsions (NEs) are frequently used in the food, cosmetics and pharmaceutical industries to deliver nutraceuticals, pharmaceutical or cosmetic active ingredients. When administering NEs parenterally, various stabilisers are added to prevent rapid plasma clearance and to successfully deliver the active ingredient to the target site. For this purpose, PEGylation is often used to prolong the circulation time of the droplets. However, the problem is to determine the optimal concentration of the PEGylating agent – the PEGylation efficacy – that ensures adequate surface protection. This is a particular challenge when the active ingredient is incorporated into the stabilising layer, where any changes could disrupt the stability of the droplet. For this reason, we aimed to determine the optimal concentration of PEG2000-DSPE for surface protection of curcumin-loaded NEs for parenteral administration using electron paramagnetic resonance (EPR) spectroscopy. NEs were prepared using the high pressure homogenisation technique with 0.1 %, 0.3 % or 0.6 % of the PEGylated phospholipid. A droplet size of approximately 100 nm and polydispersity index below 0.25 indicated suitability for parenteral application. EPR analysis showed that PEG2000-DSPE had a stabilising effect on selected NEs, which was most pronounced in the part of the stabilising layer closest to the aqueous phase. To confirm these results, protein interaction studies were carried out using dynamic light scattering, UV–Vis spectroscopy, atomic force microscopy and release studies from protein-enriched media – bovine serum albumin (BSA) or foetal bovine serum (FBS) in phosphate-buffered saline. These analyses confirmed that the addition of PEG2000-DSPE reduced protein binding to the droplets as a function of concentration, with 0.3 % providing the best protection for the droplets. Our conclusions from the EPR spectroscopy study demonstrate the usefulness of EPR in determining the optimal concentrations of PEGylating agents for surface coverage and its usefulness in the formulation development phase.

Localized surface plasmon resonance and atomic force microscopy study of model lipid membranes and their interactions with amyloid and melatonin

Alzheimer's disease (AD) is a progressive neurodegenerative disorder characterized by the accumulation of amyloid plaques in the brain. The toxicity of amyloid to neuronal cell surfaces arises from interactions between small intermediate aggregates, namely amyloid oligomers, and the cell membrane. The nature of these interactions changes with age and disease progression. In our previous work, we demonstrated that both membrane composition and nanoscale structure play crucial roles in amyloid toxicity, and that membrane models mimicking healthy neuron were less affected by amyloid than model membranes mimicking AD neuronal membranes. This understanding introduces the possibility of modifying membrane properties with membrane-active molecules, such as melatonin, to protect them from amyloid-induced damage. In this study, we employed atomic force microscopy and localized surface plasmon resonance to investigate the protective effects of melatonin. We utilized synthetic lipid membranes that mimic the neuronal cellular membrane at various stages of AD and explored their interactions with amyloid-β (1–42) in the presence of melatonin. Our findings reveal that the early diseased membrane model is particularly vulnerable to amyloid binding and subsequent damage. However, melatonin exerts its most potent protective effect on this early-stage membrane. These results suggest that melatonin could act at the membrane level to alleviate amyloid toxicity, offering the most protection during the initial stages of AD.

Comparative Evaluation of Action of RISA and Sodium Hypochlorite on the Surface Roughness of Heat Treated Single Files, Hyflex EDM and One Curve- An Atomic Force Microscopic Study

Aim: The aim of the study is to evaluate the action of RISA and Sodium hypochlorite on the surface roughness of heat treated single files, Hyflex EDM and One Curve using an Atomic Force Microscope.  Materials and Methods: A total of ten new files from each brand (Hyflex EDM and One Curve were taken. Before immersion , all the files were observed under Atomic Force Microscope to determine the surface roughness. Five files from Hyflex EDM were immersed in 5.25% sodium hypochlorite and five files were immersed in RISA solution. Five files from One Curve were immersed in 5.25 % sodium hypochlorite and the other five files were immersed in RISA solution. The dynamic immersion of the files were done by attaching it to an endomotor at constant speed [300 rpm] and torque [2.5 N Cm] into plastic tubes .After immersion, all the files were kept on the staging platform of AFM and 3mm section of the tip was examined for surface roughness.  Results: Within the limitations of this study, Hyflex EDM files immersed in sodium hypochlorite showed highest increase in surface roughness. Among the irrigant solutions used, increase in surface roughness was more for files immersed in Sodium hypochlorite as compared to files immersed in RISA solution.

Isotope labeled 3D-Raman confocal imaging and atomic force microscopy study on epithelial cells interacting with the fungus Candida albicans

The human pathogenic fungus Candida albicans damages epithelial cells during superficial infections. Here we use three-dimensional-sequential-confocal Raman spectroscopic imaging and atomic force microscopy to investigate the interaction of C. albicans wild type cells, the secreted C. albicans peptide toxin candidalysin and mutant cells lacking candidalysin with epithelial cells. The candidalysin responsible for epithelial cell damage and exhibits in its deuterated form an identifiable Raman signal in a frequency region distinct from the cellular frequency region. Vibration modes at 2100–2200 cm−1 attributed to carbon‑deuterium bending and at 477 cm−1, attributed to the nitrogen‑deuterium out-of-plane bending, found around the nucleus, can be assigned to deuterated candidalysin. Atomic force microscopy visualized 100 nm deep lesions on the cell and force-distance curves indicate the higher adhesion on pore surrounding after incubation with candidalysin. Candidalysin targets the plasma membrane, but is also found inside of the cytosol of epithelial cells during C. albicans infection.

A Novel Mechano-Synthesized Zeolitic Tetrazolate Framework for a High-Performance Triboelectric Nanogenerator and Self-Powered Selective Neurochemical Detection.

Designing a high-performing triboelectric novel material with eco-friendly, rapid, and cost-effective synthesis is the future of material research in triboelectric nanogenerators (TENG). We report a mechanochemical ball mill synthesis of a zeolitic tetrazolate framework (ZTF-8) that is isostructural with the well-known zeolitic imidazolate framework ZIF-8. ZTF-8 is extremely stable in water, 0.1 M aqueous acid/base solutions for 75 days at 25 °C, and boiling water (100 °C) for 7 days. Kelvin probe force microscopy and molecular electrostatic surface potential computational analysis exhibited that ZTF-8 has a very high positive surface potential. Atomic force microscopy and three-dimensional digital microscopy studies reveal the high roughness profile in the ZTF-8 film. The unique structure, exceptional acid/base stability, good dielectric property, and high roughness profile combined with the extremely electropositive nature of ZTF-8 make it a suitable candidate as a polymer-free triboelectric positive material in TENG with outstanding performance (power density of 720 mW/m2). High triboelectric output was further validated using the COMSOL Multiphysics simulation tool. Simple mechanical hand tapping of the ZTF-based TENG (ZTF-TENG) device generates high electric output, which was practically used to power numerous low-powered devices like tally counter, clinical thermometer, and digital clock and also illuminates 125 light-emitting diodes. In addition, the efficiency of ZTF-TENG was utilized as a self-powered device for a selective dopamine (DA) sensor with good sensitivity (377.76 mV/μM/cm2), wide range linearity (5-120 μM), and excellent limit of detection (0.42 μM).

Improving the Adhesion of Multi-Walled Carbon Nanotubes to Titanium by Irradiating the Interface with He+ Ions: Atomic Force Microscopy and X-ray Photoelectron Spectroscopy Study.

A complex study of the adhesion of multi-walled carbon nanotubes to a titanium surface, depending on the modes of irradiation with He+ ions of the "MWCNT/Ti" system, was conducted using atomic force microscopy and X-ray photoelectron spectroscopy. A quantitative assessment of the adhesion force at the interface, performed using atomic force microscopy, demonstrated its significant increase as a result of treatment of the "MWCNT/Ti" system with a beam of helium ions. The nature of the chemical bonding between multi-walled carbon nanotubes and the surface of the titanium substrate, which causes this increase in the adhesion of nanotubes to titanium as a result of ion irradiation, was investigated by X-ray photoelectron spectroscopy. It was established that this bonding is the result of the formation of chemical C-O-Ti bonds between titanium and carbon atoms with the participation of oxygen atoms of oxygen-containing functional groups, which are localized on defects in the nanotube walls formed during ion irradiation. It is significant that there are no signs of direct bonding between titanium and carbon atoms.

Biomechanical Characterization of Retinal Pigment Epitheliums Derived from hPSCs Using Atomic Force Microscopy

AbstractThe retinal pigment epithelium (RPE), a multifunctional cell monolayer located at the back of the eye, plays a crucial role in the survival and homeostasis of photoreceptors. Dysfunction or death of RPE cells leads to retinal degeneration and subsequent vision loss, such as in Age-related macular degeneration and some forms of Retinitis Pigmentosa. Therefore, regenerative medicine that aims to replace RPE cells by new cells obtained from the differentiation of human pluripotent stem cells, is the focus of intensive research. However, despite their critical interest in therapy, there is a lack of biomechanical RPE surface description. Such biomechanical properties are tightly related to their functions. Herein, we used atomic force microscopy (AFM) to analyze both the structural and mechanical properties of RPEs obtained from four cell lines and at different stages of epithelial formation. To characterize epitheliums, we used apical markers in immunofluorescence and showed the increase of transepithelial resistance, as well as the ability to secrete cytokines with an apico-basal polarity. Then, we used AFM to scan the apical surface of living or fixed RPE cells. We show that RPE monolayers underwent softening of apical cell center as well as stiffening of cell borders over epithelial formation. We also observed apical protrusions that depend on actin network, suggesting the formation of microvilli at the surface of RPE epitheliums. These RPE cell characteristics are essential for their functions into the retina and AFM studies may improve the characterization of the RPE epithelium suitable for cell therapy. Graphical Abstract

Processing of Thin Films Based on Cellulose Nanocrystals and Biodegradable Polymers by Space-Confined Solvent Vapor Annealing and Morphological Characteristics.

L-poly(lactic acid), poly(3-hydroxybutyrate), and poly-hydroxybutyrate-co-hydroxyvalerate are biodegradable polymers that can be obtained from renewable biomass sources. The aim of this study was to develop three types of environmentally friendly film biocomposites of altered microstructure by combining each of the above-mentioned polymers with cellulose nanocrystal fillers and further processing the resulting materials via space-confined solvent vapor annealing. Cellulose was previously obtained from renewable biomass and further converted to cellulose nanocrystals by hydrolysis with the lactic acid. The solutions of biodegradable polymers were spin-coated onto solid substrates before and after the addition of cellulose nanocrystals. The obtained thin film composites were further processed via space-confined solvent vapor annealing to eventually favor their crystallization and, thus, to alter the final microstructure. Indeed, atomic force microscopy studies have revealed that the presence of cellulose nanocrystals within a biodegradable polymer matrix promoted the formation of large crystalline structures exhibiting fractal-, spherulitic- or needle-like morphologies.

In-Situ AFM Studies of Surfactant Adsorption on Stainless Steel Surfaces during Electrochemical Polarization

Corrosion inhibitors are one of the best practices to prevent the far-reaching negative impacts of corrosion on ferrous alloys. A thorough understanding of their corrosion-inhibiting effects is essential for a sustainable economy and environment. Anionic surfactants are known to act efficiently as corrosion inhibitors. Here, we present that in-situ atomic force microscopy (AFM) measurements can provide deep insights into the adsorption and inhibition mechanism of surfactants on stainless steel surfaces during local corrosion. These include the configuration of surfactant molecules on the surface and how the microstructure of the stainless steel surface influences the inhibition process. Three different anionic surfactants, namely palm kernel oil (PKO), linear alkylbenzene sulfonate (LAS), and fatty alcohol ether sulfate (FAES), were investigated on a titanium-stabilized ferritic stainless steel (1.4510) in NaCl solution. For PKO, the results show random adsorption of bi- and multilayer whereas LAS and FAES adsorb only as local corrosion occurs. Thereby, LAS accumulates only locally and especially at the titanium precipitates of the 1.4510 and FAES forms a densely packed monolayer on the surface. This leads to better corrosion inhibiting properties for LAS and FAES compared to PKO.

Atomic Force Microscopy Study of the Long-Term Effect of the Glycerol Flow, Stopped in a Coiled Heat Exchanger, on Horseradish Peroxidase.

Glycerol is employed as a functional component of heat-transfer fluids, which are of use in both bioreactors and various biosensor devices. At the same time, flowing glycerol was reported to cause considerable triboelectric effects. Herein, by using atomic force microscopy (AFM), we have revealed the long-term effect of glycerol flow, stopped in a ground-shielded coiled heat exchanger, on horseradish peroxidase (HRP) adsorption on mica. Namely, the solution of HRP was incubated in the vicinity of the side of the cylindrical coil with stopped glycerol flow, and then HRP was adsorbed from this solution onto a mica substrate. This incubation has been found to markedly increase the content of aggregated enzyme on mica-as compared with the control enzyme sample. We explain the phenomenon observed by the influence of triboelectrically induced electromagnetic fields of non-trivial topology. The results reported should be further considered in the development of flow-based heat exchangers of biosensors and bioreactors intended for operation with enzymes.

Characterization of Nanocrystalline SnS Thin Film Fabricated used PLD Method for Photodetection Applications

Pulsed laser deposition was used to create tin sulfide (SnS) nanoparticles with a Nd:YAG laser (700 mJ) with laser pulses of (200, 250, 300, and 350 pulses). Nanoparticles were created and investigated using XRD, AFM, and UV-Vis spectroscopy to understand their optical, topographical, and electrical properties. After that, a SnS photodetector was built for the first time, and its performance, photoresponse, and sensitivity were evaluated. The development of monocrystalline SnS films was confirmed by X-ray diffraction (XRD) examination. Clear crystallization with increased crystalline size and the optimum orientation was observed in the sample synthesized SnS thin film treated with 300 pulses. The crystallite size increased from 44 at 200 to 77 nm for 350 pulses. These films were characterized by better surface morphology with (111) preferred crystals. In addition, atomic force microscopy (AFM) studies showed that the average diameter of generated SnS nanoparticles rose from (39.4 nm to 64.7) nm when the laser pulses increased in pulsed laser deposition. Transmission measurements were used to determine the films' absorption coefficient energy gap (Eg), and they showed that the optical transition was direct and that the transmittance value dropped with increasing laser pulses. Band gap energy is reduced from 2.139 to 1.773 eV. Moreover, Hall Effect measurements on all samples demonstrate that all thin films were n-type, with charge carrier concentration increasing with increased pulses and carrier mobility decreasing with increased pulses. The photodetectors ' photosensitivity was evaluated in the dark after depositing Al contacts on SnS thin films through a metal mask. The Pulses of enhancement cause a red shift in the values of particular detectivity and quantum efficiency. The highest responsivity was obtained at 350 pulses, 6.72×10−1 AW−1. The high (QE) of 150% at 200 p and detectivity of 2.9×1011 cm, Hz1/2.W-1 at 300p.

Dermal stiffness governs the topography of the epidermis and the underlying basement membrane in young and old human skin.

The epidermis is a stratified epithelium that forms the outer layer of the skin. It is composed primarily of keratinocytes and is constantly renewed by the proliferation of stem cells and their progeny that undergo terminal differentiation as they leave the basal layer and migrate to the skin surface. Basal keratinocytes rest on a basement membrane composed of an extracellular matrix that controls their fate via integrin-mediated focal adhesions and hemidesmosomes which are critical elements of the epidermal barrier and promote its regenerative capabilities. The distribution of basal cells with optimal activity provides the basement membrane with its characteristic undulating shape; this configuration disappears with age, leading to epidermal weakness. In this study, we present an in-depth imaging analysis of basal keratinocyte anchorage in samples of human skin from participants across the age spectrum. Our findings reveal that skin aging is associated with the depletion of hemidesmosomes that provide crucial support for stem cell maintenance; their depletion correlates with the loss of the characteristic basement membrane structure. Atomic force microscopy studies of skin and invitro experiments revealed that the increase in tissue stiffness observed with aging triggers mechanical signals that alter the basement membrane structure and reduce the extent of basal keratinocyte anchorage, forcing them to differentiate. Genomic analysis revealed that epidermal aging was associated with mechanical induction of the transcription factor Krüppel-like factor 4. The altered mechanical properties of tissue being a new hallmark of aging, our work opens new avenues for the development of skin rejuvenation strategies.

Controlling spatial distribution of functional lipids in a supported lipid bilayer prepared from vesicles

Conjugating biomolecules, such as antibodies, to bioconjugate moieties on lipid surfaces is a powerful tool for engineering the surface of diverse biomaterials, including cells and nanoparticles. We developed supported lipid bilayers (SLBs) presenting well-defined spatial distributions of functional moieties as models for precisely engineered functional biomolecular-lipid surfaces. We used quartz crystal microbalance with dissipation (QCM-D) and atomic force microscopy (AFM) to determine how vesicles containing a mixture of 1,2-dipalmitoyl-sn-glycero-3-phosphatidylcholine (DPPC) and 1,2-distearoyl-sn-glycero-3-phosphoethanolamine-N-[azido(polyethylene glycol)-2000] (DSPE-PEG-N3) form SLBs as a function of the lipid phase transition temperature (Tm). Above the DPPC Tm, DPPC/DSPE-PEG-N3 vesicles form SLBs with functional azide moieties on SiO2 substrates via vesicle fusion. Below this Tm, DPPC/DSPE-PEG-N3 vesicles attach to SiO2 intact. Intact DPPC/DSPE-PEG-N3 vesicles on the SiO2 surfaces fuse and rupture to form SLBs when temperature is brought above the DPPC Tm. AFM studies show uniform and complete DPPC/DSPE-PEG-N3 SLB coverage of SiO2 surfaces for different DSPE-PEG-N3 concentrations. As the DSPE-PEG-N3 concentration increases from 0.01 to 6 mol%, the intermolecular spacing of DSPE-PEG-N3 in the SLBs decreases from 4.6 to 1.0 nm. The PEG moiety undergoes a mushroom to brush transition as DSPE-PEG-N3 concentration varies from 0.1 to 2.0 mol%. Via copper-free click reaction, IgG was conjugated to SLB surfaces with 4.6 nm or 1.3 nm inter-DSPE-PEG-N3 spacing. QCM-D and AFM data show; 1) uniform and complete IgG layers of similar mass and thickness on the two types of SLB; 2) a higher-viscosity/less rigid IgG layer on the SLB with 4.6 nm inter-DSPE-PEG-N3 spacing. Our studies provide a blueprint for SLBs modeling spatial control of functional macromolecules on lipid surfaces, including surfaces of lipid nanoparticles and cells.

Atomic force microscopy, deformation-recovery and numerical study of wheat dough

Experimental and numerical modelling work related to microstructure and deformation of starch, gluten and wheat dough was presented. Atomic force microscopy analyses through force spectroscopy on starch samples showed elastic behaviour of both dried and reconstituted wet starch granules, where wet starch was shown to be more cohesive than dried starch. Deformation-recovery test over time under compression mode showed almost complete recovery to original sample height of gluten, whereas only a slight recovery was observed for dough. Finite element modelling was then commenced to simulate gluten deformation-recovery and starch-gluten dough deformation. The gluten geometry used for the starch-gluten dough model was obtained from cryo-SEM image from the previous work before the starch geometry was then included. The interface between the starch and gluten model was defined using viscoelastic cohesive zone elements. The modelling results suggested significant influence of gluten cellular structure towards starch-gluten dough integrity. In addition, the results from the current work further supported the previous report of the starch-gluten interfacial behaviour using viscoelastic cohesive zone model.

Synthesis and Characterization of Cerium Oxide Thin Films Fabricated via the Facile Doctor Blade Method

In this study, we present an in-depth investigation of cerium oxide (CeO2) thin films synthesized using the doctor blade approach, with polyethylene glycol employed as a binder. A comprehensive characterization employing X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), UV-visible spectroscopy, and atomic force microscopy (AFM) has been conducted to elucidate the structural, chemical, and morphological attributes of the fabricated films. The XRD analysis reveals distinctive wide diffraction peaks indicative of a face-centered cubic CeO2 crystalline structure existing in a singular phase. The morphological analysis using AFM delineates a mean square roughness of 34.54 nm, providing valuable insights into the surface topography of the CeO2 thin films. Additionally, the direct correlation between the material’s band gap, determined as 1.92 eV through UV-visible spectroscopy, and its nanostructural features is established using spectroscopic ellipsometry in conjunction with AFM studies. This approach offers a unique perspective on the optical characteristics of CeO2 films, enhancing our understanding of their nanostructures and facilitating the optimization of their performance for energy applications. Furthermore, the synergistic utilization of scanning electron microscopy (SEM) and spectroscopic ellipsometry contributes to a comprehensive understanding of the growth modes and surface characteristics of the thin films. The integration of these advanced techniques not only refines the fabrication process but also provides crucial insights into the intricate interplay between morphology and optical properties, crucial for optimizing thin films for various applications.

Conducting atomic force microscopy studies on domain wall currents of Bi5 Ti3 FeO15 nanodots fabricated by anodic aluminum oxide nanotemplate and sol-gel process.

We investigated the local current characteristics of Bi5 Ti3 FeO15 (BTFO) nanodots on Nb-doped SrTiO3 substrates affected by their ferroelectric domain structures and domain walls. The BTFO nanodots with a diameter of about 50 nm were fabricated by anodic aluminum oxide nanotemplates and a BTFO sol-gel process. Based on a piezoresponse force microscope, it was confirmed that domain walls were formed in the ferroelectric domain structures of the epitaxial BTFO nanodots. Current changes due to ferroelectric tunneling junctions according to ferroelectric polarizations in epitaxial BTFO nanodots were confirmed by conduction atomic force microscopy. In particular, the domain walls formed in the epitaxial BTFO nanodots formed high currents compared to the currents in ferroelectric tunneling junctions due to polarizations. RESEARCH HIGHLIGHTS: Ferroelectric Bi5 Ti3 FeO15 nanodots with a diameter of 50 nm. Ferroelectric domain structures observed with piezoresponse force microscopy. High domain wall currents observed at domain boundaries observed with conducting atomic force microscopy.

Phase-selective in-plane heteroepitaxial growth of H-phase CrSe2

Phase engineering of two-dimensional transition metal dichalcogenides (2D-TMDs) offers opportunities for exploring unique phase-specific properties and achieving new desired functionalities. Here, we report a phase-selective in-plane heteroepitaxial method to grow semiconducting H-phase CrSe2. The lattice-matched MoSe2 nanoribbons are utilized as the in-plane heteroepitaxial template to seed the growth of H-phase CrSe2 with the formation of MoSe2-CrSe2 heterostructures. Scanning tunneling microscopy and non-contact atomic force microscopy studies reveal the atomically sharp heterostructure interfaces and the characteristic defects of mirror twin boundaries emerging in the H-phase CrSe2 monolayers. The type-I straddling band alignments with band bending at the heterostructure interfaces are directly visualized with atomic precision. The mirror twin boundaries in the H-phase CrSe2 exhibit the Tomonaga-Luttinger liquid behavior in the confined one-dimensional electronic system. Our work provides a promising strategy for phase engineering of 2D TMDs, thereby promoting the property research and device applications of specific phases.

Highly Efficient DSSCs Sensitized Using NIR Responsive Bacteriopheophytine-a and Its Derivatives Extracted from Rhodobacter Sphaeroides Photobacteria.

Employing naturally extracted dyes and their derivatives as photosensitizers towards the construction of dye-sensitized solar cells (DSSCs) has been recently emerging for establishing sustainable energy conversion devices. In this present work, Rhodobacter Sphaeroides Photobacteria (Rh. Sphaeroides) was used as a natural source from which Bacteriopheophytine-a (Bhcl) dye was extracted. Further, two cationic derivatives of Bhcl, viz., Guanidino-bacteriopheophorbide-a (Gua-Bhcl) and (2-aminoethyl)triphenylphosphono-bacteriopheophorbide-a (2AETPPh-Bhcl) were synthesized. The thus obtained Bhcl, Gua-Bhcl and 2AETPPh-Bhcl were characterized using liquid chromatography-mass spectrometry (LC-MS) and their photophysical properties were investigated using excitation and emission studies. All three near-infrared (NIR) responsive dyes were employed as natural sensitizers towards the construction of DSSC devices, using platinum as a photocathode, dye-sensitized P25-TiO2 as a photoanode and I-/I3- as an electrolyte. DSSCs fabricated using all three dyes have shown reasonably good photovoltaic performance, among which 2AETPPh-Bhcl dye has shown a relatively higher power conversion efficiency (η) of 0.38% with a short circuit photocurrent density (JSC) of 1.03 mA cm-2. This could be attributed to the dye's natural optimal light absorption in the visible and NIR region and uniform dispersion through the electrostatic interaction of the cationic derivatives on the TiO2 photoanode. Furthermore, the atomic force microscopy studies and electrochemical investigations using cyclic voltammetry, electrochemical impedance spectroscopy and Bode's plot also supported the enhancement in performance attained with 2AETPPh-Bhcl dye.

Effect of Sterilization and Irrigating Solutions on Nanostructure Alteration of Ni-Ti Rotary Instruments in Endodontics: An Atomic Force Microscopic Study.

This study aimed to evaluate the effect of 5.25% sodium hypochlorite (NaOCl) and 17% ethylenediaminetetraacetic acid (EDTA) and sterilization on the nanostructural alteration of nickel titanium (Ni-Ti) rotary file systems in endodontics using the atomic force microscopy (AFM). The study was performed on four commercially available rotary Ni-Ti files: group I-Vortex Blue (Dentsply), group II-ProTaper Next (Dentsply), group III-Mtwo (VDW), and group IV-iRaCe (FKG). Each group was divided into four subgroups (n = 4), that is, subgroup A-control (new rotary file), subgroup B-subjected for five cycles of autoclave, subgroup C-immersed in 5.25% NaOCl for 5 minutes, and subgroup D-immersed in 17% EDTA solutions for 5 minutes. All the specimens were evaluated with AFM using roughness average (RA) and root-mean-square (RMS) values for surface roughness. Among control groups, Vortex Blue showed the least RA and RMS values; the highest surface roughness was seen with Mtwo files. All the Ni-Ti rotary files showed a statistically significant (P <0.05) increase in surface hardness when subjected to autoclave and treatment with different irrigating solutions. In particular, 17% EDTA caused the highest surface deterioration in all the groups. AFM analysis revealed increased surface roughness values recorded for all the rotary files when treated with irrigating solutions and autoclave cycles.

Thin film deposition of undoped and Ni-doped cobalt ferrite on MgO (110) substrates using pulsed laser deposition technique

The thin film samples of pristine and Ni-doped Cobalt ferrite(CFO) are deposited on MgO(110) substrates through pulsed laser deposition technique. The recorded X-ray diffraction scans of the samples confirms the thin film deposition of the said material on the given substrate. From the Atomic Force Microscopy studies, the surface roughness of CoFe1.7Ni0.3O4 thin film is found to be 0.62 nm, which is more than CoFe2O4 and CoFe1.5Ni0.5O4 (0.34 nm and 0.45 nm), attributed to the surface defects and recrystallization process. The x-ray photoelectron emission spectroscopy (XPS) survey spectra of the thin film samples confirm the presence of Co, Ni, Fe, O and C. In our case, the XPS-wide scans revealed the +2-oxidation state for Co and +2 as well as +3 oxidation states for Fe. The respective binding energy positions and the ratio of relative contribution to the overall intensity of Co and Fe ions at the octahedral and tetrahedral sites are also discussed in this paper. It has been shown that the Field Cooled-Zero Field Cooled magnetization curves do not merge until 400 K, which confirms that the Curie temperature Tc is higher than 400 K.